The GW53xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW52xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Node names should be generic, so change the sdma node name format 'sdma'
into 'dma-controller'.
Acked-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Start to use more generic resistive-adc-touch node. ti,tsc2046 is an ADC
controller used for resistive touchscreen. So, define it as ADC and
attach resistive-adc-touch to it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes the following warning:

arch/arm/boot/dts/imx6sx-udoo-neo.dtsi:309: check: Please don't use multiple
blank lines

While at it, use tabs indent for some pinctrl entries.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes the following error:

arch/arm/boot/dts/imx6sl.dtsi:714: error: code indent should use tabs
where possible
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

LPI2C requires two clocks, add the missed IPG clock.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The clock name should be per clock, not ipg clock.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add DDR pinmux which may be used in U-Boot after synchronising all
them device trees (and includes) from Linux.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SoM itself provides the display interface, see [1] page 20.
Those pins have to be used as the RGB/DPI interface or not used
at all. So rather than duplicate the pinmux settings in every
carrier board DT, better move them into the SoM DTSI.

[1] https://wiki.dh-electronics.com/images/2/2e/DOC_DHCOM-Standard-Specification_R01_2016-11-17.pdfSigned-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx6ull-kontron-bl.dtb wasn't build as part of the
CONFIG_SOC_IMX6UL option. Add it to the list.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is no need in differentiating between the different SoM versions
that only differ in memory size, etc. It's much cleaner to simplify
the devicetrees and let them be more generic.

If necessary the bootloader will update the devicetree dynamically
to contain the correct size of the memory.

We also get rid of the N6xxx notation in the compatibles and file
names, as they are not really used anymore and often result in
confusion.

This is a breaking change, but the impact shouldn't be too big and it
makes usage and maintenance easier in the future.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add fixed power supplies to the EEPROM nodes to suppress a warning:

  at24 2-0050: supply vcc not found, using dummy regulator
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

DT spec expects generic DMA controller node name as "dma-controller" to
enable validations.
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i2c2 is routed to the pins dedicated as DDC in the module standard.
Reduce clock rate to 100kHz to be in line with VESA standard and hook
this bus up to the HDMI node.

Fixes: 708ed264 ("ARM: dts: imx6qdl-kontron-samx6i: increase i2c-frequency")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[m.felsch@pengutronix.de: add fixes line]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add ethernet-phy node so we can drop the deprecated fec phy-reset-gpios
property. The reset-assert-us value is taken from the existing logic
since the fec driver will add an 1ms assert delay per default if
phy-reset-gpios is used and phy-reset-duration is not specified.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On some older hardware models this is needed. It will do no harm if used
with newer models though.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,

[17:19:39.183] event1  - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1  - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1  - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1  - not using input device '/dev/input/event1'

This will then cause the APP weston-touch-calibrator can't list touch devices.

root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.

And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warning:

arch/arm/boot/dts/vf610.dtsi:5: check: Please don't use multiple blank
 lines
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warning:

arch/arm/boot/dts/vf610-twr.dts:172: warning: please, no spaces at the
 start of a line
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid spaces in indent but rather use tabs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx7d-pico.dtsi:44: error: code indent should use tabs
 where possible
arch/arm/boot/dts/imx7d-pico.dtsi:44: warning: please, no spaces at the
 start of a line
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Replace the license text with SPDX identifiers.

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx6qdl-sabrelite.dtsi:1: warning: Missing or
 malformed SPDX-License-Identifier tag in line 1
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warnings:

arch/arm/boot/dts/imx6qdl-phytec-mira-peb-av-02.dtsi:67: error: code
 indent should use tabs where possible
arch/arm/boot/dts/imx6qdl-phytec-mira-peb-av-02.dtsi:67: warning:
 please, no spaces at the start of a line
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx6qdl-mba6.dtsi:247: check: Please don't use
 multiple blank lines
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Replace the license text with SPDX identifiers.

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx6q-sabrelite.dts:1: warning: Missing or malformed
 SPDX-License-Identifier tag in line 1
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add property for ERR006687 hardware workaround.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In most cases this is related to fsl,err006687-workaround-present, which
requires a GPIO interrupt next a GIC interrupt.

This fixes the dtbs_check warning:
imx6dl-mba6a.dtb: ethernet@2188000: More than one condition true in oneOf schema:
        {'$filename': 'Documentation/devicetree/bindings/net/fsl,fec.yaml',
[...]
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add connection between the backlight controller and LCD panel.
With that the backlight is automatically switched on when the panel
is on or switched off when the panel is blanked.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>