Although for the most part, the AB8500 uses common bindings, some
of the ways in which they are used differ slightly to the common
uses of those bindings. To clear up some of these varying concepts
we provide some documentation describing each of the properties and
how they are used.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Replace tps65910_misc_init with a dedicated init function for the
32-kHz-crystal input, and make the code more readable.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This was introduced in commit

        876989d5 (mfd: Add device tree probe support for mc13xxx)

for spi and later while introducing support for i2c copied to the i2c
driver.

Modifying driver details is very strange, for example probing an
mc13892 device (instantiated via dt) removes the driver's ability to
handle (traditionally probed) mc13783 devices in this case.
I'm not aware of any problems that make this hack necessary and if
there were some, they'd have to be fixed in the spi/i2c core, not in
a driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Current code has been converted to use regmap APIs, the io_mutex is not needed.
Thus remove the io_mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This fixes below section mismatch warning:

  LD      drivers/mfd/built-in.o
WARNING: drivers/mfd/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function pm800_probe() to the function .devexit.text:pm80x_deinit()
The function __devinit pm800_probe() references
a function __devexit pm80x_deinit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
pm80x_deinit() so it may be used outside an exit section.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Check the return value of regmap_read() rather than the read value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM5110 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices. It combines an advanced DSP
feature set with a flexible, high-performance audio hub CODEC.

The support is based on the Arizona core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.

This patch adds data tables for the WM5110.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There are many samsung multifunction devices which are
s2mps11, s5m8767, s5m8763 etc.
This devices can support regulator, rtc, charger.
I will be supporting the Samsung mfd drivers, that are currently
in development and will be upstreamed shortly.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch support irq handling driver for s2mps11.
As this patch use regmap_irq, s5m8767 and s5m8763 are modified with
regmap_irq.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch add Samsung S2MPS11 mfd driver.
The S2MPS11 can support regulators and RTC.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

As Prefix of Samsung pmic changed from s5m to s2m,
To make common mfd driver for s2m and s5m series,
This patch rename header of Samsung mfd and modify mfd driver.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Previous naming rule of samsung pmic start with s5m prefix.
But It is changed by s2m.
To cover various samsung s2m and s5m series,
This patch modify function and variable name for common usage.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Previously, Samsung PMIC naming rule start with prefix of s5m.
But Naming rule is changed.
From now on, Prefix will be changed to s2m.
So, To support pmic series of s5m and s2m, change mfd file and directory name.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

A few more registers used on newer devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The registers have stride 2 so we can write the loop properly now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This fixes below build error when CONFIG_MFD_88PM800=m.

ERROR: "pm80x_regmap_config" [drivers/mfd/88pm800.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This fixes below build warning if CONFIG_OF is not set.

  CC      drivers/mfd/max77686.o
drivers/mfd/max77686.c:37:42: warning: 'max77686_pmic_dt_match' defined but not used [-Wunused-variable]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

add rtc driver for MARVELL 88PM80X PMIC and enable rtc function.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Remove the clocks from the list of regulators to correct the value of
MAX77686_REG_MAX which is used in the regulator driver to represent the no.
of regulators present in max77686.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds device tree support for mfd driver and adds
Documentation/devicetree/bindings/mfd/max77686.txt.
This patch also intialize max77686 pointer to NULL in max77686_i2c_probe
to silent a compile time warning.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Presently driver expects irq_gpio pin in platform data and maps it to irq
itself. But we can also directly specify the interrupt in DT or platform file.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

According to TRM, though we mask the interrupts in interrupt-mask register,
interrupt source-register still provide the status of the masked interrupts.
So we should apply irq_mask_cur to read interrupt source-register value before
handling.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

PMIC's regmap should be used to read pmic interrupt registers.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

device_init_wakeup uses the dev_name() of the device to set the
name of the wakeup_source which appears in
/sys/kernel/debug/wakeup_sources.

For a platform device, that name is not set until platform_device_add
calls dev_set_name.

So the call to device_init_wakeup() must be after the call to
platform_device_add().
Making this change causes correct names to appear in the
wakeup_sources file.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

in hw design, 800 is mainly for pmic control, while 805 for audio.
but there are 3 registers which controls class D speaker property,
and they are defined in 800 i2c client domain. so 805 codec driver
needs to use 800 i2c client to access class D speaker reg for
audio path management. so add this workaround for the purpose to
let 805 access 800 i2c in some scenario.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

88PM800 and 88PM805 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according
to requirement.

88pm80x.c provides common i2c driver handling for both 800 and
805, such as i2c_driver init, regmap init, read/write api etc.

88pm800.c handles specifically for 800, such as chip init, irq
init/handle, mfd device register, including rtc, onkey, regulator(
to be add later) etc. besides that, 800 has three i2c device, one
regular i2c client, two other i2c dummy for gpadc and power purpose.

88pm805.c handles specifically for 805, such as chip init, irq
init/handle, mfd device register, including codec, headset/mic detect
etc.

the i2c operation of both 800 and 805 are via regmap, and 88pm80x-i2c
exported a group of r/w bulk r/w and bits set API for facility.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The core and irq Arizona parts should be boolean as they depend on non
exported symbols.

This fixes the following build errors:

ERROR: "wm5102_aod" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "wm5102_irq" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "irq_set_chip_and_handler_name" [drivers/mfd/arizona-irq.ko]  undefined!
ERROR: "wm5102_patch" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_init" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_exit" [drivers/mfd/arizona-core.ko] undefined!
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

ARRAY_SIZE() may be larger than the number of supplies actually used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

References to the WM5102 tables need to be guarded.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We're testing for a specific value and while SPI does not detect I/O
errors I2C can.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Ensures we don't leak the enable we just did.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

These registers will be used in future devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This ensures that if we are using a GPIO as a wake source it continues to
function while we're suspended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Now we have regcache sync region we can use it to do a more efficient
sync of the pin configuration after we reset the device during suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Rather than open coding the enable GPIO control in the MFD core use the
API to push the management on to the regulator driver. The immediate
advantage is slight for most systems but this will in future allow device
configurations where an external regulator is used for DCVDD.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

While the core isn't useful by itself it does depend on regmap so try to
force that on.
Reported-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>