All of these ioctls are unused and most of them just duplicate what drm
already provides.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

Properly init the MMU and add MMU entries when adding GTT entries
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

Right now, all we need to know about the blitter is that it's not doing
anything that can be messed up when fiddling with MMU mappings.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

Add 2D blit status and MMU fault interrupts to the IRQ handler.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

Old MMU code never wrote PDs or PTEs to any registers. Now we do, and
that's a good start.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>

this is the second pull request for 3.15 radeon changes. Highlights this time:
- Better VRAM usage
- VM page table rework
- Enabling different UVD clocks again
- Some general cleanups and improvements

* 'drm-next-3.15' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: remove struct radeon_bo_list
  drm/radeon: drop non blocking allocations from sub allocator
  drm/radeon: remove global vm lock
  drm/radeon: use normal BOs for the page tables v4
  drm/radeon: further cleanup vm flushing & fencing
  drm/radeon: separate gart and vm functions
  drm/radeon: fix VCE suspend/resume
  drm/radeon: fix missing bo reservation
  drm/radeon: limit how much memory TTM can move per IB according to VRAM usage
  drm/radeon: validate relocations in the order determined by userspace v3
  drm/radeon: add buffers to the LRU list from smallest to largest
  drm/radeon: deduplicate code in radeon_gem_busy_ioctl
  drm/radeon: track memory statistics about VRAM and GTT usage and buffer moves v2
  drm/radeon: add a way to get and set initial buffer domains v2
  drm/radeon: use variable UVD clocks
  drm/radeon: cleanup the fence ring locking code
  drm/radeon: improve ring lockup detection code v2

Just move all fields into radeon_cs_reloc, removing unused/duplicated fields.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

- Fix the execbuf rebind performance regression due to topic/ppgtt (Chris).
- Fix up the connector cleanup ordering for sdvod i2c and dp aux devices (Imre).
- Try to preserve the firmware modeset config on driver load. And a bit of prep
  work for smooth takeover of the fb contents (Jesse).
- Prep cleanup for larger gtt address spaces on bdw (Ben).
- Improve our vblank_wait code to make hsw modesets faster (Paulo).
- Display debugfs file (Jesse).
- DRRS prep work from Vandana Kannan.
- pipestat interrupt handler to fix a few races around vblank/pageflip handling
  on byt (Imre).
- Improve display fuse handling for display-less SKUs (Damien).
- Drop locks while stalling for the gpu when serving pagefaults to improve
  interactivity (Chris).
- And as usual piles of other improvements and small fixes all over.

* tag 'drm-intel-next-2014-02-14' of ssh://git.freedesktop.org/git/drm-intel: (65 commits)
  drm/i915: fix NULL deref in the load detect code
  drm/i915: Only bind each object rather than for every execbuffer
  drm/i915: Directly return the vma from bind_to_vm
  drm/i915: Simplify i915_gem_object_ggtt_unpin
  drm/i915: Allow blocking in the PDE alloc when running low on gtt space
  drm/i915: Don't allocate context pages as mappable
  drm/i915: Handle set_cache_level errors in the status page setup
  drm/i915: Don't pin the status page as mappable
  drm/i915: Don't set PIN_MAPPABLE for legacy ringbuffers
  drm/i915: Handle set_cache_level errors in the pipe control scratch setup
  drm/i915: split PIN_GLOBAL out from PIN_MAPPABLE
  drm/i915: Consolidate binding parameters into flags
  drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
  drm/i915: sdvo: fix error path in sdvo_connector_init
  drm/i915: dp: fix order of dp aux i2c device cleanup
  drm/i915: add unregister callback to connector
  drm/i915: don't reference null pointer at i915_sink_crc
  drm/i915/lvds: Remove dead code from failing case
  drm/i915: don't preserve inherited configs with nothing on v2
  drm/i915/bdw: Split up PPGTT cleanup
  ...

Not needed any more.
Signed-off-by: Christian König <christian.koenig@amd.com>

Not needed any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

No need to make it more complicated than necessary,
just allocate the page tables as normal BO and
flush whenever the address change.

v2: update comments and function name
v3: squash bug fixes, page directory and tables patch
v4: rebased on Mareks changes
Signed-off-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Both are complex enough on their own.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Userspace should set the first 4 bits of drm_radeon_cs_reloc::flags to
a number from 0 to 15. The higher the number, the higher the priority,
which means a buffer with a higher number will be validated sooner.

The old behavior is preserved: Buffers used for write are prioritized over
read-only buffers if the userspace doesn't set the number.

v2: add buffers to buckets directly, then concatenate them
v3: use a stable sort
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

The statistics are:
- VRAM usage in bytes
- GTT usage in bytes
- number of bytes moved by TTM

The last one is actually a counter, so you need to sample it before and after
command submission and take the difference.

This is useful for finding performance bottlenecks. Userspace queries are
also added.

v2: use atomic64_t
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

When passing buffers between processes, the receiving process needs to know
the original buffer domain, so that it doesn't accidentally move the buffer.

v2: reserve the buffer
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Now that Christian fixed the performance problems with
the feedback buffer in mesa, we can enable variable UVD
clocks.  There are multiple UVD power states associated
with different types and numbers of streams.  This uses
the appropriate state based on that information rather
than always using the fastest UVD clocks which saves some
power.  One possible downside is that this may adversely
affect decode benchmarks since these power states target
specific playback requirements rather than maximum
performance.  If that becomes an issue, we can add a
sysfs attribute to force the max UVD state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

We no longer need to take the ring lock while checking for
a gpu lockup, so just cleanup the code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Use atomics and jiffies_64, so that we don't need to have the
ring mutex locked any more and avoid wrap arounds.

v2: fix some checkpatch warnings
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

So this is the initial pull request for radeon drm-next 3.15. Highlights:
- VCE bringup including DPM support
- Few cleanups for the ring handling code

* 'drm-next-3.15' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: cleanup false positive lockup handling
  drm/radeon: drop radeon_ring_force_activity
  drm/radeon: drop drivers copy of the rptr
  drm/radeon/cik: enable/disable vce cg when encoding v2
  drm/radeon: add support for vce 2.0 clock gating
  drm/radeon/dpm: properly enable/disable vce when vce pg is enabled
  drm/radeon/dpm: enable dynamic vce state switching v2
  drm/radeon: add vce dpm support for KV/KB
  drm/radeon: enable vce dpm on CI
  drm/radeon: add vce dpm support for CI
  drm/radeon: fill in set_vce_clocks for CIK asics
  drm/radeon/dpm: fetch vce states from the vbios
  drm/radeon/dpm: fill in some initial vce infrastructure
  drm/radeon/dpm: move platform caps fetching to a separate function
  drm/radeon: add callback for setting vce clocks
  drm/radeon: add VCE version parsing and checking
  drm/radeon: add VCE ring query
  drm/radeon: initial VCE support v4
  drm/radeon: fix CP semaphores on CIK

Updates from Jean-Fracois for the TDA998x driver, which are on top of
the fixes you have previously pulled, except these changes aren't
intended for -rc, but the next merge window.

Several of these are issues of correctness - passing more correct HDMI
info packets, not reading registers in older chips documented as write
only (despite appearing to be read/write in later chips).  Others are
code cleanups (using definitions rather than constants where we have
them already in the kernel).

Additional functionality is also added by way of optional support for
the IRQ from the TDA998x, which allows us to avoid busy-waiting for
the EDID reads.

* 'tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
  drm/i2c: tda998x: always use the same device for all kernel messages
  drm/i2c: tda998x: adjust the audio clock divider for S/PDIF
  drm/i2c: tda998x: code optimization
  drm/i2c: tda998x: remove the unused variable ca_i2s
  drm/i2c: tda998x: make the audio code more readable
  drm/i2c: tda998x: use irq for connection status and EDID read
  drm/i2c: tda998x: always enable EDID read IRQ
  drm/i2c: tda998x: add DT documentation
  drm/i2c: tda998x: add DT support
  drm/i2c: tda998x: don't read write-only registers
  drm/i2c: tda998x: don't freeze the system at audio startup time
  drm/i2c: tda998x: change probe message origin
  drm/i2c: tda998x: code cleanup
  drm/i2c: tda998x: clean up error chip version checking
  drm/i2c: tda998x: check more I/O errors
  drm/i2c: tda998x: simplify the i2c read/write functions
  drm/i2c: tda998x: use ALSA IEC958 definitions and update audio frequency
  drm/i2c: tda998x: add the active aspect in HDMI AVI frame
  drm/i2c: tda998x: use HDMI constants

- Yet more steps towards atomic modeset from Ville.
- DP panel power sequencing improvements from Paulo.
- irq code cleanups from Ville.
- 5.4 GHz dp lane clock support for bdw/hsw from Todd.
- Clock readout support for hsw/bdw (aka fastboot) from Jesse.
- Make pipe underruns report at ERROR level (Ville). This is to check our
  improved watermarks code.
- Full ppgtt support from Ben for gen7.
- More fbc fixes and improvements from Ville all over the place, unfortunately
  not yet enabled by default on more platforms.
- w/a cleanups from Ville.
- HiZ stall optimization settings (Chia-I Wu).
- Display register mmio offset refactor patch from Antti.
- RPS improvements for corner-cases from Jeff McGee.

* tag 'drm-intel-next-2014-02-07' of ssh://git.freedesktop.org/git/drm-intel: (166 commits)
  drm/i915: Update rps interrupt limits
  drm/i915: Restore rps/rc6 on reset
  drm/i915: Prevent recursion by retiring requests when the ring is full
  drm/i915: Generate a hang error code
  drm/i915: unify FLIP_DONE macro names
  drm/i915: vlv: s/spin_lock_irqsave/spin_lock/ in irq handler
  drm/i915: factor out valleyview_pipestat_irq_handler
  drm/i915: vlv: don't unmask IIR[DISPLAY_PIPE_A/B_VBLANK] interrupt
  drm/i915: Reorganize display pipe register accesses
  drm/i915: Treat using a purged buffer as a source of EFAULT
  drm/i915: Convert EFAULT into a silent SIGBUS
  drm/i915: release mutex in i915_gem_init()'s error path
  drm/i915: check for oom when allocating private_default_ctx
  drm/i915/vlv: WA to fix Voltage not getting dropped to Vmin when Gfx is power gated.
  drm/i915: Get rid of acthd based guilty batch search
  drm/i915: Use hangcheck score to find guilty context
  drm/i915: Drop WaDisablePSDDualDispatchEnable:ivb for IVB GT2
  drm/i915: Fix IVB GT2 WaDisableDopClockGating and WaDisablePSDDualDispatchEnable
  drm/i915: Don't access snooped pages through the GTT (even for error capture)
  drm/i915: Only print information for filing bug reports once
  ...

Conflicts:
	drivers/gpu/drm/i915/intel_dp.c

drm: DisplayPort AUX framework for v3.15-rc1

This series of patches implements a small framework that abstracts away
some of the functionality that the DisplayPort AUX channel provides. It
comes with a set of generic helpers that use the driver implementations
to reduce code duplication.

* tag 'drm/dp-aux-for-3.15-rc1' of git://anongit.freedesktop.org/tegra/linux:
  drm/dp: Allow registering AUX channels as I2C busses
  drm/dp: Add DisplayPort link helpers
  drm/dp: Add drm_dp_dpcd_read_link_status()
  drm/dp: Add AUX channel infrastructure

Implements an I2C-over-AUX I2C adapter on top of the generic drm_dp_aux
infrastructure. It extracts the retry logic from existing drivers, which
should help in porting those drivers to this new helper.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v5:
- move comments partially to to header file
- keep MOT set between I2C messages
- return -EPROTO on short reads

Changes in v4:
- fix typo "bitrate" -> "bit rate"

Changes in v3:
- add back DRM_DEBUG_KMS and DRM_ERROR messages
- embed i2c_adapter within struct drm_dp_aux
- fix typo in comment

Add a helper to probe a DP link (read out the supported DPCD revision,
maximum rate, link count and capabilities) as well as power up the DP
link and configure it accordingly.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v5:
- export helpers

Changes in v4:
- fix a couple of typos in comments as pointed out by Alex Deucher

Changes in v3:
- split into drm_dp_link_power_up() and drm_dp_link_configure()
- do not change sink state for DPCD versions earlier than 1.1
- sleep for 1-2 ms after setting local sink to D0 state
- read and write consecutive registers where possible
- read DPCD revision when link is probed
- remove duplicate kerneldoc

The function reads the link status (6 bytes starting at offset 0x202)
from the DPCD so that it can be conveniently passed to other DPCD
helpers.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This is a superset of the current i2c_dp_aux bus functionality and can
be used to transfer native AUX in addition to I2C-over-AUX messages.

Helpers are provided to read and write the DPCD, either blockwise or
byte-wise. Many of the existing helpers for DisplayPort take a copy of a
portion of the DPCD and operate on that, without a way to write data
back to the DPCD (e.g. for configuration of the link).

Subsequent patches will build upon this infrastructure to provide common
functionality in a generic way.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v5:
- move comments partially to struct drm_dp_aux_msg in header file
- return -EPROTO on short reads in DPCD helpers

Changes in v4:
- fix a typo in a comment

Changes in v3:
- reorder drm_dp_dpcd_writeb() arguments to be more intuitive
- return number of bytes transferred in drm_dp_dpcd_write()
- factor out drm_dp_dpcd_access()
- describe error codes

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes for ARM platforms.  Most are fixes for DTS
  files, mostly from DT conversion on OMAP which is still finding a few
  issues here and there.

  There's a couple of small stale code removal patches that we usually
  queue for the next release instead, but they seemed harmless enough to
  bring in now.

  Also, a fix for backlight on some PXA platforms, and a cache
  configuration fix for Tegra, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
  MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
  ARM: tegra: only run PL310 init on systems with one
  ARM: tegra: Add head numbers to display controllers
  ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
  ARM: tegra: fix RTC0 alias for Cardhu
  ARM: dove: dt: revert PMU interrupt controller node
  Documentation: dt: OMAP: Update Overo/Tobi
  ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
  ARM: dts: omap3-tobi: Use the correct vendor prefix
  ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
  ARM: OMAP2+: Remove legacy macros for zoom platforms
  ARM: OMAP2+: Remove MACH_NOKIA_N800
  ARM: dts: N900: add missing compatible property
  ARM: dts: N9/N950: fix boot hang with 3.14-rc1
  ARM: OMAP1: nokia770: enable tahvo-usb
  ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
  ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
  ARM: dts: omap3-gta04: Fix mmc1 properties.
  ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
  ARM: OMAP2+: add missing ARCH_HAS_OPP
  ...

Pull regulator fixes from Mark Brown:
 "Mostly unexciting driver fixes, plus one fix to lower the severity of
  the log message when we don't use an optional regulator - the fixes
  for ACPI system made this come up more often and it was correctly
  observed that it was causing undue concern for users"

* tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: max14577: Fix invalid return value on DT parse success
  regulator: core: Change dummy supplies error message to a warning
  regulator: s5m8767: Add missing of_node_put
  regulator: s5m8767: Use of_get_child_by_name
  regulator: da9063: Bug fix when setting max voltage on LDOs 5-11

Pull timer fix from Thomas Gleixner:
 "Serialize the registration of a new sched_clock in the currently ARM
  only generic sched_clock facilty to avoid sched_clock havoc"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched_clock: Prevent callers from seeing half-updated data

Pull x86 fixes from Thomas Gleixner:

 - a bugfix which prevents a divide by 0 panic when the newly introduced
   try_msr_calibrate_tsc() fails

 - enablement of the Baytrail platform to utilize the newfangled msr
   based calibration

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: tsc: Add missing Baytrail frequency to the table
  x86, tsc: Fallback to normal calibration if fast MSR calibration fails

Pull irq fixes from Thomas Gleixner:
 "Another four fixlets to tame the ARM orion irq chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: orion: Fix getting generic chip pointer.
  irqchip: orion: clear stale interrupts in irq_startup
  irqchip: orion: use handle_edge_irq on bridge irqs
  irqchip: orion: clear bridge cause register on init