- 24 Jul, 2018 7 commits
-
-
Ivan Khoronzhuk authored
This document describes MQPRIO and CBS Qdisc offload configuration for cpsw driver based on examples. It potentially can be used in audio video bridging (AVB) and time sensitive networking (TSN). Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ivan Khoronzhuk authored
Need to restore shapers configuration after interface was down/up. This is needed as appropriate configuration is still replicated in kernel settings. This only shapers context restore, so vlan configuration should be restored by user if needed, especially for devices with one port where vlan frames are sent via ALE. Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ivan Khoronzhuk authored
The cpsw has up to 4 FIFOs per port and upper 3 FIFOs can feed rate limited queue with shaping. In order to set and enable shaping for those 3 FIFOs queues the network device with CBS qdisc attached is needed. The CBS configuration is added for dual-emac/single port mode only, but potentially can be used in switch mode also, based on switchdev for instance. Despite the FIFO shapers can work w/o cpdma level shapers the base usage must be in combine with cpdma level shapers as described in TRM, that are set as maximum rates for interface queues with sysfs. One of the possible configuration with txq shapers and CBS shapers: Configured with echo RATE > /sys/class/net/eth0/queues/tx-0/tx_maxrate /--------------------------------------------------- / / cpdma level shapers +----+ +----+ +----+ +----+ +----+ +----+ +----+ +----+ | c7 | | c6 | | c5 | | c4 | | c3 | | c2 | | c1 | | c0 | \ / \ / \ / \ / \ / \ / \ / \ / \ / \ / \ / \ / \ / \ / \ / \ / \/ \/ \/ \/ \/ \/ \/ \/ +---------|------|------|------|-------------------------------------+ | +----+ | | +---+ | | | +----+ | | | | v v v v | | +----+ +----+ +----+ +----+ p p+----+ +----+ +----+ +----+ | | | | | | | | | | o o| | | | | | | | | | | f3 | | f2 | | f1 | | f0 | r CPSW r| f3 | | f2 | | f1 | | f0 | | | | | | | | | | | t t| | | | | | | | | | \ / \ / \ / \ / 0 1\ / \ / \ / \ / | | \ X \ / \ / \ / \ / \ / \ / \ / | | \/ \ \/ \/ \/ \/ \/ \/ \/ | +-------\------------------------------------------------------------+ \ \ FIFO shaper, set with CBS offload added in this patch, \ FIFO0 cannot be rate limited ------------------------------------------------------ CBS shaper configuration is supposed to be used with root MQPRIO Qdisc offload allowing to add sk_prio->tc->txq maps that direct traffic to appropriate tx queue and maps L2 priority to FIFO shaper. The CBS shaper is intended to be used for AVB where L2 priority (pcp field) is used to differentiate class of traffic. So additionally vlan needs to be created with appropriate egress sk_prio->l2 prio map. If CBS has several tx queues assigned to it, the sum of their bandwidth has not overlap bandwidth set for CBS. It's recomended the CBS bandwidth to be a little bit more. The CBS shaper is configured with CBS qdisc offload interface using tc tool from iproute2 packet. For instance: $ tc qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1 $ tc -g class show dev eth0 +---(100:ffe2) mqprio | +---(100:3) mqprio | +---(100:4) mqprio | +---(100:ffe1) mqprio | +---(100:2) mqprio | +---(100:ffe0) mqprio +---(100:1) mqprio $ tc qdisc add dev eth0 parent 100:1 cbs locredit -1440 \ hicredit 60 sendslope -960000 idleslope 40000 offload 1 $ tc qdisc add dev eth0 parent 100:2 cbs locredit -1470 \ hicredit 62 sendslope -980000 idleslope 20000 offload 1 The above code set CBS shapers for tc0 and tc1, for that txq0 and txq1 is used. Pay attention, the real set bandwidth can differ a bit due to discreteness of configuration parameters. Here parameters like locredit, hicredit and sendslope are ignored internally and are supposed to be set with assumption that maximum frame size for frame - 1500. It's supposed that interface speed is not changed while reconnection, not always is true, so inform user in case speed of interface was changed, as it can impact on dependent shapers configuration. For more examples see Documentation. Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ivan Khoronzhuk authored
That's possible to offload vlan to tc priority mapping with assumption sk_prio == L2 prio. Example: $ ethtool -L eth0 rx 1 tx 4 $ qdisc replace dev eth0 handle 100: parent root mqprio num_tc 3 \ map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 1 $ tc -g class show dev eth0 +---(100:ffe2) mqprio | +---(100:3) mqprio | +---(100:4) mqprio | +---(100:ffe1) mqprio | +---(100:2) mqprio | +---(100:ffe0) mqprio +---(100:1) mqprio Here, 100:1 is txq0, 100:2 is txq1, 100:3 is txq2, 100:4 is txq3 txq0 belongs to tc0, txq1 to tc1, txq2 and txq3 to tc2 The offload part only maps L2 prio to classes of traffic, but not to transmit queues, so to direct traffic to traffic class vlan has to be created with appropriate egress map. Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ivan Khoronzhuk authored
According to TRM tx rated channels should be in 7..0 order, so correct it. Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ivan Khoronzhuk authored
The cpdma channel highest priority is from hi to lo number. The driver has limited number of descriptors that are shared between number of cpdma channels. Number of queues can be tuned with ethtool, that allows to not spend descriptors on not needed cpdma channels. In AVB usually only 2 tx queues can be enough with rate limitation. The rate limitation can be used only for hi priority queues. Thus, to use only 2 queues the 8 has to be created. It's wasteful. So, in order to allow using only needed number of rate limited tx queues, save resources, and be able to set rate limitation for them, let assign tx cpdma channels in backward order to queues. Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'mlx5e-updates-2018-07-18-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5e-updates-2018-07-18 This series includes update for mlx5e net device driver. 1) From Feras Daoud, Added the support for firmware log tracing, first by introducing the firmware API needed for the task and then For each PF do the following: 1- Allocate memory for the tracer strings database and read it from the FW to the SW. 2- Allocate and dma map tracer buffers. Traces that will be written into the buffer will be parsed as a group of one or more traces, referred to as trace message. The trace message represents a C-like printf string. Once a new trace is available FW will generate an event indicates new trace/s are available and the driver will parse them and dump them using tracepoints event tracing Enable mlx5 fw tracing by: echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable Read traces by: cat /sys/kernel/debug/tracing/trace 2) From Roi Dayan, Remove redundant WARN when we cannot find neigh entry 3) From Jianbo Liu, TC double vlan support - Support offloading tc double vlan headers match - Support offloading double vlan push/pop tc actions 4) From Boris, re-visit UDP GSO, remove the splitting of UDP_GSO_L4 packets in the driver, and exposes UDP_GSO_L4 as a PARTIAL_GSO feature. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 23 Jul, 2018 33 commits
-
-
Boris Pismenny authored
This patch removes the splitting of UDP_GSO_L4 packets in the driver, and exposes UDP_GSO_L4 as a PARTIAL_GSO feature. Thus, the network stack is not responsible for splitting the packet into two. Signed-off-by: Boris Pismenny <borisp@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Jianbo Liu authored
As we can configure two push/pop actions in one flow table entry, add support to offload those double vlan actions in a rule to HW. Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Jianbo Liu authored
Extract actions offloading code to a new function, and also extend data structures for double vlan actions. Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Jianbo Liu authored
We can match on both outer and inner vlan tags, add support for offloading that. Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Roi Dayan authored
It is possible for neigh entry not to exist if it was cleaned already. When we bring down an interface the neigh gets deleted but it could be that our listener for neigh event to clear the encap valid bit didn't start yet and the neigh update last used work is started first. In this scenario the encap entry has valid bit set but the neigh entry doesn't exist. Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Saeed Mahameed authored
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Feras Daoud authored
Add the tracer file to the makefile and add the init function to the load one flow. Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Feras Daoud authored
For each message the driver should do the following: 1- Find the message string in the strings database 2- Count the param number of each message 3- Wait for the param events and accumulate them 4- Calculate the event timestamp using the local event timestamp and the first timestamp event following it. 5- Print message to trace log Enable the tracing by: echo 1 > /sys/kernel/debug/tracing/events/mlx5/mlx5_fw/enable Read traces by: cat /sys/kernel/debug/tracing/trace Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Feras Daoud authored
The tracer has one event, event 0x26, with two subtypes: - Subtype 0: Ownership change - Subtype 1: Traces available An ownership change occurs in the following cases: 1- Owner releases his ownership, in this case, an event will be sent to inform others to reattempt acquire ownership. 2- Ownership was taken by a higher priority tool, in this case the owner should understand that it lost ownership, and go through tear down flow. The second subtype indicates that there are traces in the trace buffer, in this case, the driver polls the tracer buffer for new traces, parse them and prepares the messages for printing. The HW starts tracing from the first address in the tracer buffer. Driver receives an event notifying that new trace block exists. HW posts a timestamp event at the last 8B of every 256B block. Comparing the timestamp to the last handled timestamp would indicate that this is a new trace block. Once the new timestamp is detected, the entire block is considered valid. Block validation and parsing, should be done after copying the current block to a different location, in order to avoid block overwritten during processing. Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Saeed Mahameed authored
Create a memory key and protection domain for the tracer log buffer. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Feras Daoud authored
For each PF do the following: 1- Allocate memory for the tracer strings database and read the strings from the FW to the SW. These strings will be used later for parsing traces. 2- Allocate and dma map tracer buffers. Traces that will be written into the buffer will be parsed as a group of one or more traces, referred to as trace message. The trace message represents a C-like printf string. First trace of a message holds the pointer to the correct string in strings database. The following traces holds the variables of the message. Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
Feras Daoud authored
Implement FW tracer logic and registers access, initialization and cleanup flows. Initializing the tracer will be part of load one flow, as multiple PFs will try to acquire ownership but only one will succeed and will be the tracer owner. Signed-off-by: Feras Daoud <ferasda@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linuxSaeed Mahameed authored
mlx5 core infrastructure updates and fixes. From Eran: - Add MPEGC (Management PCIe General Configuration) registers and btis - Fix tristate and description for MLX5 module rom Feras: - Add hardware structures for the firmware tracer From Jainbo: - Core support for double vlan push/pop steering action From Max: - Add XRQ commands definitions From Noa: - Add missing SET_DRIVER_VERSION command translation From Roi: - Use ERR_CAST() instead of coding it From Tariq: - Better return types for CQE API Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-
David S. Miller authored
Bryan Whitehead says: ==================== lan743x: Add features to lan743x driver This patch series adds extra features to the lan743x driver. Updates for v4: Patch 6/8 - Modified get/set_wol to use super set of MAC and PHY driver support. Patch 7/9 - In set_eee, return the return value from phy_ethtool_set_eee. Updates for v3: Removed patch 9 from this series, regarding PTP support Patch 6/8 - Add call to phy_ethtool_get_wol to lan743x_ethtool_get_wol Patch 7/8 - Add call to phy_ethtool_set_eee on (!eee->eee_enabled) Updates for v2: Patch 3/9 - Used ARRAY_SIZE macro in lan743x_ethtool_get_ethtool_stats. Patch 5/9 - Used MAX_EEPROM_SIZE in lan743x_ethtool_set_eeprom. Patch 6/9 - Removed unnecessary read of PMT_CTL. Used CRC algorithm from lib. Removed PHY interrupt settings from lan743x_pm_suspend Change "#if CONFIG_PM" to "#ifdef CONFIG_PM" ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement RSS support Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement EEE support Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement power management Supports suspend, resume, and Wake on LAN Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement ethtool eeprom access Also provides access to OTP (One Time Programming) Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement ethtool message level Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement ethtool statistics Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Use default link setting functions Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bryan Whitehead authored
Implement ethtool get_drvinfo Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Sergei Shtylyov says: ==================== sh_eth: clean up the TSU register accessors Here's a set of 5 patches against DaveM's 'net-next.git' repo. They do a final clean up of the TSU register accessors... ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
sh_eth_tsu_read_entry() is still asymmetric with sh_eth_tsu_write_entry() WRT their prototypes -- make them symmetric by passing to the former a TSU register offset instead of its address and also adding the (now necessary) 'ndev' parameter... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
We can add the TSU register base address to a TSU register offset right in sh_eth_tsu_write_entry(), no need to do it in its callers... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
With sh_eth_tsu_get_offset() now actually returning TSU register's offset, we can at last use it in sh_eth_tsu_{read|write}(). Somehow this saves 248 bytes of object code with AArch64 gcc 4.8.5... :-) Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
sh_eth_tsu_get_offset(), despite its name, returns a TSU register's address, not its offset. Make this function match its name and return a register's offset from the TSU registers base address instead. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sergei Shtylyov authored
sh_eth_tsu_get_offset() is called several times by the driver, remove *inline* and move that function from the header to the driver itself to let gcc decide whether to expand it inline or not... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
YueHaibing authored
qe_muram_alloc return a unsigned long integer,which should not compared with zero. check it using IS_ERR_VALUE() to fix this. Fixes: c19b6d24 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ursula Braun says: ==================== net/smc: patches 2018-07-23 here are some small patches for SMC: Just the first patch contains a functional change. It allows to differ between the modes SMCR and SMCD on s390 when monitoring SMC sockets. The remaining patches are cleanups without functional changes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ursula Braun authored
The page map address is already stored in the RMB descriptor. There is no need to derive it from the cpu_addr value. Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ursula Braun authored
Link group field tokens_used_mask is a bitmap. Use macro DECLARE_BITMAP for its definition. Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stefan Raspl authored
Replace a frequently used construct with a more readable variant, reducing the code. Also might come handy when we start to support more than a single per link group. Signed-off-by: Stefan Raspl <raspl@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-