- 25 Jan, 2008 40 commits
-
-
Aurelien Jarno authored
The patch below adds the "Pinnacle Dazzle DVC 100" to the list of cards supported by the em28xx driver. As the configuration is the same as the DVC 90 one, it simply adds a new USB ID to the list of devices supported by the DVC 90 configuration. Signed-off-by:
Aurelien Jarno <aurelien@aurel32.net> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Akinobu Mita authored
Check pci_register_driver() error in module_init. Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Michael Krufky authored
Ensure that the audio is muted at attach-time Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
struct tuner holds state for tuner-core, only -- move it into tuner-core.c Signed-off-by:
-
Michael Krufky authored
replace tda9887_info and tda9887_dbg printk macros with tuner_info and tuner_dbg, defined in tuner-i2c.h Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Use TUNER_SET_CONFIG to set configuration in tda9887's private state structure, rather than storing tda9887-specific configuration within struct tuner. Update handling of TUNER_SET_CONFIG by tuner-core, to call &t->fe.ops.analog_demod_ops rather than &t->fe.ops.tuner_ops analog_demod_ops.set_config passes the request to tuner_ops.set_config, so this does not break other drivers. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Prevent us from wasting some extra bytes of memory Thanks to Trent Piepho, for pointing this out. Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Frej Drejhammar authored
The auto selection of pertinent helper chips (VIDEO_HELPER_CHIPS_AUTO) should select the wm8775 driver, which is used by at least one Conexant 2388x based card (Hauppauge HVR-1300), if VIDEO_CX88 is selected. Signed-off-by:
Frej Drejhammar <frej.drejhammar@gmail.com> Signed-off-by:
Ricardo Cerqueira <v4l@cerqueira.org> Signed-off-by:
-
Ricardo Cerqueira authored
All cx2388 boards need the line-in audio to be routed from an external ADC (refered to as "ADC mode" in the spec sheet), since the chip is uncapable of dealing with baseband audio directly. So... this patch enables normal mode when using the tuner (TV or Radio), and enables ADC mode with any other source. It'll probably only work with boards that have supported ADCs (such as the Wolfson wm9775) Signed-off-by:
-
Michael Krufky authored
We should not mute the audio input when we stop the codec, because it will interfere with the live uncompressed stream. Signed-off-by:
Jelle Foks <jelle@foks.8m.com> Signed-off-by:
-
Ricardo Cerqueira authored
Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds. The wm8775 module initializes the audio input at "route 2", which doesn't hold true for all boards. The HVR-1300, for example, uses route 1 for tuner audio, and route 2 for baseband. So we must route the audio to the proper input depending on what video input is being used. Signed-off-by:
-
Jelle Foks authored
Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in cx88-blackbird.c The encoder is never muted, hence unmuting should then only be necessary once after hardware initialization. I tested this from warm boots and cold boots (with long power down time to ensure the sram in the chip is emptied), and found that after the firmware upload the encoder is apparently not muted, making the unmutes unnecessary. Signed-off-by:
-
Jelle Foks authored
Remove the unnecessary msleep()'s in cx88-blackbird.c Signed-off-by:
-
Jelle Foks authored
This patch should fix the 'muted audio' and 'raspy audio' problem for mpeg2 streams out of cx88-blackbird devices. Especially mythtv users would find that the audio would often sound bad (aliased, or 'raspy'), mainly related to channel changes, many (all?) other users would find that there was no audio at all in the mpeg data from the encoder chip, unless the audio was manually unmuted. The patch includes the following modifications: Don't actually start the mpeg2 encoder until the device is read from by the application. Wait until the audio is stable for at least 400ms before starting the mpeg encoder. Mute/Unmute the audio when starting/stopping the mpeg encoder. Stop the mpeg encoder when changing parameters and when changing tuner frequency. Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of whether or not the mpeg2 encoder is active. Load the firmware on cx88-blackbird driver load. Signed-off-by:
-
Mauro Carvalho Chehab authored
ATSC standard-specific firmware is D2633 on both v2.5 and v2.7. Better to auto-select this firmware, overriding ctrl.d2633. Signed-off-by: -
Michael Krufky authored
use VSB IF frequency ( 44 / 5.38 MHz ) if qam_if is invalid or unspecified Acked-by:
Steven Toth <stoth@hauppauge.com> Signed-off-by:
-
Michael Krufky authored
On the s5h1409 demod, the IF frequency for VSB is limited to 44 / 5.38 MHz. Hardcode VSB IF frequency within the driver to 44 / 5.38 MHz. QAM IF frequency remains configurable via attach-time configuration. Acked-by:
-
Andrew Morton authored
Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Acked-by:
Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by:
-
Mauro Carvalho Chehab authored
The previous code were a little bit messy. Cleans it up. Signed-off-by: -
Mauro Carvalho Chehab authored
Avoids de-alocating buffers before finishing to fill a buffer Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Daniel Walker authored
The ctrlUrbLock has all it's users commented out, and so it's unused. This patch removes it. Signed-off-by:
Daniel Walker <dwalker@mvista.com> Signed-off-by:
Thierry MERLE <thierry.merle@free.fr> Signed-off-by:
-
Andrew Morton authored
Signed-off-by:
-
Daniel Walker authored
There are a few error paths which don't unlock the usbvision->lock. So I've added mutex_unlock() calls to fix those paths. Signed-off-by:
-
Andrew Morton authored
drivers/media/video/et61x251/et61x251_core.c:390: warning: 'et61x251_i2c_read' defined but not used drivers/media/video/et61x251/et61x251_core.c:397: warning: 'et61x251_i2c_write' defined but not used Signed-off-by:
-
Andrew Morton authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
The changes at vivi_template make debug option to not work properly. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Thanks to Jean Delvare <khali@linux-fr.org> for pointing this. Signed-off-by: -
Michael Krufky authored
If we pass TDA18271_GATE_DIGITAL into tda18271_attach(), it will always try to use the digital demodulator's i2c gate. If we pass TDA18271_GATE_ANALOG into tda18271_attach(), it will always try to use the analog demodulator's i2c gate. If we pass TDA18271_GATE_AUTO into tda18271_attach(), it will try to use the analog demodulator's i2c gate when tuning in analog mode, and it will try to use the digital demodulator's i2c gate when tuning in digital mode. Signed-off-by:
-
Michael Krufky authored
Use an enum rather than an integer #define to store analog / digital state. Signed-off-by:
-
Mauro Carvalho Chehab authored
Those newer functions are used by saa7134-empress. Adds export for them: +EXPORT_SYMBOL_GPL(saa7134_g_ctrl); +EXPORT_SYMBOL_GPL(saa7134_s_ctrl); +EXPORT_SYMBOL_GPL(saa7134_queryctrl); Signed-off-by: -
Mauro Carvalho Chehab authored
saa7134 were converted to video_ioctl2, but saa7134_empress weren't. This broke saa7134-empress, since it were dependent of saa7134_common_ioctl. With the conversion, the module had a size decrease of 436 bytes on x86_64: text data bss dec hex filename 5196 4912 4 10112 2780 old/saa7134-empress.ko 4760 4912 4 9676 25cc new/saa7134-empress.ko Signed-off-by:
-
