- 29 Feb, 2016 29 commits
-
-
Chen-Yu Tsai authored
Now that clock delay settings for 8 bit DDR are correct, and vqmmc support is available, we can enable MMC_CAP_1_8V_DDR support. This enables MMC HS-DDR at up to 52 MHz, even if signal voltage switching is not available. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Chen-Yu Tsai authored
Allwinner's MMC controller needs to run at double the card clock rate for 8 bit DDR transfer modes. Interestingly, this is not needed for 4 bit DDR transfers. Different clock delays are needed for 8 bit eMMC DDR, due to the increased module clock rate. For the A80 though, the same values for 4 bit and 8 bit are shared. The new values for the other SoCs were from A83T user manual's "new timing mode" default values, which describes them in clock phase, rather than delay periods. These values were used without any modification. They may not be correct, but they work. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Chen-Yu Tsai authored
DDR transfer modes include UHS-1 DDR50 and MMC HS-DDR (or MMC_DDR52). Consider MMC_DDR52 when setting clock delays. Since MMC high speed mode goes up to 52 MHz instead of 50 MHz for SD, and this number is visible in the capability macro, increase the clock rate upper limit to 52 MHz. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Wolfram Sang authored
The bus width is sometimes the actual bus width, and sometimes indices to different arrays encoding the bus width. In my debugging case "2" could mean 8-bit as well as 4-bit, which was extremly confusing. Let's use the human-readable actual bus width in all places. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Jaehoon Chung authored
In linux/mmc/host.h, mmc_card_is_removable() is already defined. There is no reason that it doesn't use. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Jisheng Zhang authored
The sdhci_iproc_remove() is jsut a wrapper to sdhci_pltfm_unregister. So use the sdhci_pltfm_unregister() for the .remove hook directly. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Acked-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Stefan Wahren authored
Since sdhci-iproc can support bcm2835 we need add the compatible string to the binding. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Scott Branden <sbranden@broadcom.com> Acked-by: Eric Anholt <eric@anholt.net> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Scott Branden <sbranden@broadcom.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Stefan Wahren authored
Scott Branden from Broadcom said that the BCM2835 eMMC IP core is very similar to IPROC and share most of the quirks. So use this driver instead of separate one. The sdhci-iproc contains a better workaround for the clock domain crossing problem which doesn't need any delays. This results in a better write performance. Btw we get the rid of the SDHCI_CAPABILITIES hack in the sdhci_readl function. Suggested-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Acked-by: Scott Branden <sbranden@broadcom.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Stefan Wahren authored
This patch moves the definition of the MMC capabilities from the probe function into iproc platform data. After that we are able to add support for another platform more easily. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Suggested-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Scott Branden <sbranden@broadcom.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Wolfram Sang authored
I had to use the source to determine what I need to write to 'test' so that all tests are run. Let's mention this explicitly in 'testlist'. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Wolfram Sang authored
I don't see a reason why a host driver should depend on the card driver. It also prevents that we can use the mmc_test driver. So, remove it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Wolfram Sang authored
IMO this info is only useful for developers. Most users won't need this information, since there is not much they can do about it. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Arnd Bergmann authored
When DT based probing is used but the DMA request fails, the driver will print uninitialized stack data from the rx_req and tx_req variables, as indicated by this warning: drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_probe': drivers/mmc/host/omap_hsmmc.c:2162:3: warning: 'rx_req' may be used uninitialized in this function [-Wmaybe-uninitialized] dev_err(mmc_dev(host->mmc), "unable to obtain RX DMA engine channel %u\n", rx_req); This removes the DMA request line number from the warning, which is the easiest solution and won't hurt us any more as we are planning to remove the legacy code path anyway. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Fu, Zhonghui authored
This patch enables sdhci-acpi devices to suspend/resume asynchronously. This will improve system suspend/resume speed. After enabling the sdhci-acpi devices and all their child devices to suspend/resume asynchronously on ASUS T100TA, the system suspend-to-idle time is reduced from 1645ms to 1089ms, and the system resume time is reduced from 940ms to 908ms. Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Fu, Zhonghui authored
This patch enables mmc hosts to suspend/resume asynchronously. This will improve system suspend/resume speed. After applying this patch and enabling all mmc hosts' child devices to suspend/resume asynchronously on ASUS T100TA, the system suspend-to-idle time is reduced from 1645ms to 1107ms, and the system resume time is reduced from 940ms to 914ms. Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com> Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Chen-Yu Tsai authored
eMMC chips require 2 power supplies, vmmc for internal logic, and vqmmc for driving output buffers. vqmmc also controls signaling voltage. Most boards we've seen use the same regulator for both, nevertheless the 2 have different usages, and should be set separately. This patch adds support for vqmmc regulator supply, including voltage switching. The MMC core can use this to try different signaling voltages for eMMC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Chen-Yu Tsai authored
Let .set_ios() fail if mmc_regulator_set_ocr() fails to enable and set a proper voltage for vmmc. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Chen-Yu Tsai authored
sunxi_mmc_init_host() originated from Allwinner kernel sources. The magic numbers written to various registers was never documented. Add comments for values found in Allwinner user manuals. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Stefan Wahren authored
The RPi firmware-based clocks driver can actually disable unused clocks, so when switching to use it we ended up losing our MMC clock once all devices were probed. This patch adopts the changes from 1e5a0a9a ("mmc: sdhci-bcm2835: Actually enable the clock") to sdhci-iproc. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Chuanxiao Dong authored
Clock frequency values written to an mmc host should not be less than the minimum clock frequency which the mmc host supports. Signed-off-by: Yuan Juntao <juntaox.yuan@intel.com> Signed-off-by: Pawel Wodkowski <pawelx.wodkowski@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Stefan Wahren authored
This patch adopts the changes from 475c9e43 ("mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails") to sdhci-iproc. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Scott Branden <sbranden@broadcom.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Rameshwar Prasad Sahu authored
The Arason SD host controller supports set block count command (cmd23) and high speed mode. This patch re-enable both of these features that was disabled. For device that doesn't support high speed, it should configure its capability register accordingly instead disables it explicitly. Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Kishon Vijay Abraham I authored
Since v4.3+, CONFIG_REGULATOR_PBIAS should be enabled (for platforms that have PBIAS regulator) in order for MMC1 to work. Add a more verbose print to help enable CONFIG_REGULATOR_PBIAS for users using a olddefconfig or a custom .config. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Masahiro Yamada authored
Variable assignment just before return is redundant. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Peter Chen authored
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Geliang Tang authored
Use to_delayed_work() instead of open-coding it. Signed-off-by: Geliang Tang <geliangtang@163.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Geliang Tang authored
Use to_delayed_work() instead of open-coding it. Signed-off-by: Geliang Tang <geliangtang@163.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Markus Elfring authored
This issue was detected by using the Coccinelle software. Two pointer checks could be repeated by the sdricoh_init_mmc() function during error handling even if the relevant properties can be determined for the involved variables before by source code analysis. * This implementation detail could be improved by adjustments for jump targets according to the Linux coding style convention. * Drop an unnecessary initialisation for the variable "mmc" then. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
Markus Elfring authored
These variables will eventually be set to an appropriate value a bit later. * host * iobase * result Thus let us omit the explicit initialisation at the beginning. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-
- 28 Feb, 2016 11 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Thomas Gleixner: "A rather largish series of 12 patches addressing a maze of race conditions in the perf core code from Peter Zijlstra" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf: Robustify task_function_call() perf: Fix scaling vs. perf_install_in_context() perf: Fix scaling vs. perf_event_enable() perf: Fix scaling vs. perf_event_enable_on_exec() perf: Fix ctx time tracking by introducing EVENT_TIME perf: Cure event->pending_disable race perf: Fix race between event install and jump_labels perf: Fix cloning perf: Only update context time when active perf: Allow perf_release() with !event->ctx perf: Do not double free perf: Close install vs. exit race
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "This update contains: - Hopefully the last ASM CLAC fixups - A fix for the Quark family related to the IMR lock which makes kexec work again - A off-by-one fix in the MPX code. Ironic, isn't it? - A fix for X86_PAE which addresses once more an unsigned long vs phys_addr_t hickup" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/mpx: Fix off-by-one comparison with nr_registers x86/mm: Fix slow_virt_to_phys() for X86_PAE again x86/entry/compat: Add missing CLAC to entry_INT80_32 x86/entry/32: Add an ASM_CLAC to entry_SYSENTER_32 x86/platform/intel/quark: Change the kernel's IMR lock bit to false
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixlet from Thomas Gleixner: "A trivial printk typo fix" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/deadline: Fix trivial typo in printk() message
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: "Four small fixes for irqchip drivers: - Add missing low level irq handler initialization on mxs, so interrupts can acutally be delivered - Add a missing barrier to the GIC driver - Two fixes for the GIC-V3-ITS driver, addressing a double EOI write and a cache flush beyond the actual region" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar() irqchip/mxs: Add missing set_handle_irq() irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull staging/android fix from Greg KH: "Here is one patch, for the android binder driver, to resolve a reported problem. Turns out it has been around for a while (since 3.15), so it is good to finally get it resolved. It has been in linux-next for a while with no reported issues" * tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds authored
Pull USB fixes from Greg KH: "Here are a few USB fixes for 4.5-rc6 They fix a reported bug for some USB 3 devices by reverting the recent patch, a MAINTAINERS change for some drivers, some new device ids, and of course, the usual bunch of USB gadget driver fixes. All have been in linux-next for a while with no reported issues" * tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: MAINTAINERS: drop OMAP USB and MUSB maintainership usb: musb: fix DMA for host mode usb: phy: msm: Trigger USB state detection work in DRD mode usb: gadget: net2280: fix endpoint max packet for super speed connections usb: gadget: gadgetfs: unregister gadget only if it got successfully registered usb: gadget: remove driver from pending list on probe error Revert "usb: hub: do not clear BOS field during reset device" usb: chipidea: fix return value check in ci_hdrc_pci_probe() usb: chipidea: error on overflow for port_test_write USB: option: add "4G LTE usb-modem U901" USB: cp210x: add IDs for GE B650V3 and B850V3 boards USB: option: add support for SIM7100E usb: musb: Fix DMA desired mode for Mentor DMA engine usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage usb: dwc2: USB_DWC2 should depend on HAS_DMA usb: dwc2: host: fix the data toggle error in full speed descriptor dma usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc usb: dwc3: Fix assignment of EP transfer resources usb: dwc2: Add extra delay when forcing dr_mode
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs fixes from Al Viro. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: do_last(): ELOOP failure exit should be done after leaving RCU mode should_follow_link(): validate ->d_seq after having decided to follow namei: ->d_inode of a pinned dentry is stable only for positives do_last(): don't let a bogus return value from ->open() et.al. to confuse us fs: return -EOPNOTSUPP if clone is not supported hpfs: don't truncate the file when delete fails
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "We didn't have a batch last week, so this one is slightly larger. None of them are scary though, a handful of fixes for small DT pieces, replacing properties with newer conventions. Highlights: - N900 fix for setting system revision - onenand init fix to avoid filesystem corruption - Clock fix for audio on Beaglebone-x15 - Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6) + misc smaller stuff" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: MAINTAINERS: Extend info, add wiki and ml for meson arch MAINTAINERS: alpine: add a new maintainer and update the entry ARM: at91/dt: fix typo in sama5d2 pinmux descriptions ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption Revert "regulator: tps65217: remove tps65217.dtsi file" ARM: shmobile: Remove shmobile_boot_arg ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code ARM: shmobile: Move shmobile_scu_base from .text to .bss ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid ARM: OMAP2+: Improve omap_device error for driver writers ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property ARM: OMAP2+: Set system_rev from ATAGS for n900 ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl ARM: dts: kirkwood: use unique machine name for ds112 ARM: dts: imx6: remove bogus interrupt-parent from CAAM node
-
Al Viro authored
... or we risk seeing a bogus value of d_is_symlink() there. Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
... otherwise d_is_symlink() above might have nothing to do with the inode value we've got. Cc: stable@vger.kernel.org # v4.2+ Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-