- 02 Mar, 2010 19 commits
-
-
Pete Zaitcev authored
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API checker, so I have no choice but band-aid it quick. There's no attempt to reuse DMA buffers. Control messages are only sent rarely anyway. Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Enrico Scholz authored
hardware reports wrong interrupt. Although such a situation should not happen, the compiler complains about this access. This patch adds a sanity check and generates warning to detect such issues. Signed-off-by:
Enrico Scholz <enrico.scholz@sigma-chemnitz.de> Acked-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
Valentin Longchamp authored
On various mxc boards, the intial ULPI reads resulted in a timeout which prevented the transceiver to be identified and thus the ehci device to be probed. Initializing the hardware lines connected to the transceiver (through pdata->init call) before actually enabling clocks and configuring registers in the devices fixes this problem. Signed-off-by:
Valentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by:
-
Mark Adamson authored
Removed CS5 and CS6 from data bits since these are not supported in FTDI hardware. Signed-off-by:
Mark J. Adamson <mark.adamson@ftdichip.com> Signed-off-by:
-
Johan Hovold authored
Latency timeout was read but never stored on port probe. When ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0 rather than the default 16ms. Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Johan Hovold authored
Fixes confusing "serial_chars_in_buffer = port 0" messages. Signed-off-by:
-
Johan Hovold authored
We always push characters to ldisc immediately regardless of ASYNC_LOW_LATENCY. Signed-off-by:
-
Johan Hovold authored
Resubmitting read urb fails with -EPERM if completion handler runs while urb is being killed on close. This should not be reported as an error. Signed-off-by:
-
Simon Arlott authored
Changes: Return an empty string for modulation when there is no connection Fix sysfs unload race conditions Log firmware load process, remove delay Add new configuration interface Remove cxacru-cf.bin Signed-off-by:Simon Arlott <simon@fire.lp0.eu> Signed-off-by:
-
Simon Arlott authored
This has never worked properly because wsize passed to cxacru_cm() is incorrectly set to the number of values instead of the data bytes. The maximum number of values that can be set at once is 7 which means the device will not get enough data to work with and none of the configuration values will be used. At least one existing cxacru-cf.bin file contains invalid data which will prevent the modem from syncing properly. Fixing it is likely to break existing systems, and the new sysfs interface for setting configuration parameters can provide the same functionality. A script is provided to convert from the original format. Signed-off-by:
-
Simon Arlott authored
The modem can be configured using CM_REQUEST_CARD_DATA_SET, although CM_REQUEST_CARD_DATA_GET does not return any data. Tested by setting the modulation (0x0a) option. There is a list of parameters in the following archive, but the meaning of many of them is not well documented: http://sourceforge.net/project/shownotes.php?release_id=301825 This source also indicates that the highest parameter set is 0x4a but this varies by model so an arbitrary limit of 0x7f has been used (the index is a 32-bit integer). Signed-off-by:
-
Simon Arlott authored
Firmware writing takes 256ms per 4KB with OHCI, which is very slow compared to 7ms per 4KB with UHCI. Until I have access to a hardware USB analyser it may not be possible to determine why this happens. Instead of appearing to do nothing, log progress when writing firmware and then log the ATM device information when finished. Remove an unnecessary 4 second delay. Signed-off-by:
-
Simon Arlott authored
These commands were found by accident... fortunately it still works even if the flash memory is erased, despite having no USB device IDs. Some example sysfs code for raw command access: http://simon.arlott.org/pub/cxacru/raw.cSigned-off-by:
-
Simon Arlott authored
It is possible for usb_get_intfdata() to return NULL if sysfs is accessed while the module is being unloaded or the device is being removed. Move the access code to an inline function in usbatm.h, and return -ENODEV if any of the pointers are NULL. It should not be possible for the instance data or atm device to be invalid until after unbind() completes and the sysfs attributes have been removed. Signed-off-by:
-
Simon Arlott authored
When attempting to read data that is not actually an array of values, the length may be negative which causes an Oops due to a likely access off the end of the data array. This bug should not occur under normal use unless the device returns an invalid response. Signed-off-by:
-
Simon Arlott authored
When there is no connection, return an empty string instead of "0" for the connection modulation. Signed-off-by:
-
Martin Fuzzey authored
Signed-off-by:
Martin Fuzzey <mfuzzey@gmail.com> Signed-off-by:
-
Martin Fuzzey authored
Also fixes tab/space issue causing checkpatch to complain. Signed-off-by:
-
Martin Fuzzey authored
This driver is a Full / Low speed only USB host for the i.MX21. Signed-off-by:
-
- 01 Mar, 2010 21 commits
-
-
Linus Torvalds authored
Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci * 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits) DaVinci DM365: Adding support for SPI EEPROM DaVinci DM365: Adding DM365 SPI support DaVinci DM355: Modifications to DM355 SPI support DaVinci: SPI: Adding header file for SPI support. davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table() DaVinci: DM365: Voice codec support for the DM365 SoC davinci: clock: let clk->set_rate function sleep Add SDA and SCL pin numbers to i2c platform data davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138 davinci: build list of unused EDMA events dynamically davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case davinci: Keep count of channel controllers on a platform davinci: Correct return value of edma_alloc_channel api davinci: add CDCE949 support on DM6467 EVM davinci: add support for CDCE949 clock synthesizer davinci: da850/omap-l138 EVM: register for suspend support davinci: da850/omap-l138: add support for SoC suspend davinci: add power management support DaVinci: DM365: Changing default queue for DM365. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-devLinus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits) sata_via: Delay on vt6420 when starting ATAPI DMA write ata: Detect Delkin Devices compact flash pata_efar: Enable parallel scanning pata_atiixp: enable parallel scan [libata] pata_atiixp: add locking for parallel scanning [libata] pata_efar: add locking for parallel scanning libata: Pass host flags into the pci helper [libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI libata: Allow pata_legacy to be built on non-ISA but PCI systems pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards [libata] pata_at91: fix backslash-continued string pata_via: store UDMA masks in via_isa_bridges table pata_via: fix address setup timings underlocking pata_serverworks: fix error message pata_serverworks: fix PIO setup for the second channel pata_efar: fix secondary port support pata_cypress: fix PIO timings underclocking pata_cs5535: use correct values for PIO1 and PIO2 data timings pata_cmd64x: remove unused definitions ...
-
Bart Hartgers authored
When writing a disc on certain lite-on dvd-writers (also rebadged as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends up in the datastream and on the disc, causing silent corruption. Delaying between sending the CDB and starting DMA seems to prevent this. I do not know if there are burners that do not suffer from this, but the patch should be safe for those as well. There are many reports of this issue, but AFAICT no solution was found before. For example: http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.htmlSigned-off-by:
Bart Hartgers <bart.hartgers@gmail.com> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
Ben Gardner authored
I have a Delkin Devices compact flash card that isn't being recognized using the SATA/PATA drivers. The card is recognized and works with the deprecated ATA drivers. The error I am seeing is: ata1.00: failed to IDENTIFY (device reports invalid type, err_mask=0x0) I tracked it down to ata_id_is_cfa() in include/linux/ata.h. The Delkin card has id[0] set to 0x844a and id[83] set to 0. This isn't what the kernel expects and is probably incorrect. The simplest work-around is to add a check for 0x844a to ata_id_is_cfa(). Signed-off-by:
Ben Gardner <gardner.ben@gmail.com> Signed-off-by:
-
Alan Cox authored
Again originally proposed by Bartlomiej but this does it by using the generic helper logic instead. Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Alan Cox authored
This was originally proposed by Bartlomiej but as a device specific expansion of the init_one function rather than making the helper more generic. Enable the parallel scan via the generic flags. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
This is similar change as commit 60c3be38 for ata_piix host driver and while pata_atiixp doesn't enable parallel scan yet the race could probably also be triggered by requesting re-scanning of both ports at the same time using SCSI sysfs interface. [Ported to current tree without other patch dependancies by Alan Cox] Original is Signed-off-by:
Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> This one is Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Add clearing of UDMA enable bit also for PIO modes and then add extra locking for parallel scanning. This is similar change as commit 60c3be38 for ata_piix host driver and while pata_efar doesn't enable parallel scan yet the race could probably also be triggered by requesting re-scanning of both ports at the same time using SCSI sysfs interface. [Ported to current kernel without other patch dependancies by Alan Cox] Original is Signed-off-by:
-
Alan Cox authored
This allows parallel scan and the like to be set without having to stop using the existing full helper functions. This patch merely adds the argument and fixes up the callers. It doesn't undo the special cases already in the tree or add any new parallel callers. Signed-off-by:
-
Christoph Egger authored
The marvell driver comtains a fallback to ahci for the sata ports which is incorrectly checked as CONFIG_AHCI while the only AHCI config item is actually called SATA_AHCI (which also sounds sensible considering it's a fallback for the sata ports). Signed-off-by:
Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Signed-off-by:
-
Alan Cox authored
This is needed for some unsupported hardware setups on strange 64bit mainboards where crazy stuff has been done like putting flash ata adapters on the LPC bus, or where the real hardware is hidden/confused. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
PDC2026x chipsets need the same treatment as PDC20246 one. This is completely untested but will hopefully fix UDMA issues that people have been reporting against pata_pdc202xx_old for the last couple of years. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
On Monday 04 January 2010 02:30:24 pm Russell King wrote: > Found the problem - getting rid of the read of the alt status register > after the command has been written fixes the UDMA CRC errors on write: > > @@ -676,7 +676,8 @@ void ata_sff_exec_command(struct ata_port *ap, const struct > ata_taskfile *tf) > DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command); > > iowrite8(tf->command, ap->ioaddr.command_addr); > - ata_sff_pause(ap); > + ndelay(400); > +// ata_sff_pause(ap); > } > EXPORT_SYMBOL_GPL(ata_sff_exec_command); > > > This rather makes sense. The PDC20247 handles the UDMA part of the > protocol. It has no way to tell the PDC20246 to wait while it suspends > UDMA, so that a normal register access can take place - the 246 ploughs > on with the register access without any regard to the state of the 247. > > If the drive immediately starts the UDMA protocol after a write to the > command register (as it probably will for the DMA WRITE command), then > we'll be accessing the taskfile in the middle of the UDMA setup, which > can't be good. It's certainly a violation of the ATA specs. Fix it by adding custom ->sff_exec_command method for UDMA33 chipsets. Debugged-by:Russell King <rmk@arm.linux.org.uk> Signed-off-by:
-
Jeff Garzik authored
Noticed and rough patch by Joe Perches. Signed-off-by: -
Bartlomiej Zolnierkiewicz authored
* store UDMA masks in via_isa_bridges[] and while at it make "flags" field to be u8 instead of u16 * convert the driver to use UDMA masks from via_isa_bridges[] * remove no longer needed VIA_UDMA* defines Make some minor documentation and CodingStyle fixes while at it. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Correct via_do_set_mode() documentation while at it. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
Timing registers should be programmed with the desired number of clocks minus one clock. Signed-off-by:
-
Bartlomiej Zolnierkiewicz authored
There shouldn't be any problems with it as IDE cs5535 host driver has been using those values for years and they match values given in the (publicly available) datasheet. Signed-off-by:
-
