- 20 Aug, 2017 27 commits
-
-
Bhumika Goyal authored
Make this const as it is only stored in the type field of a device structure, which is const. Done using Coccinelle. Signed-off-by:
Bhumika Goyal <bhumirks@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Colin Ian King authored
The mask of sns_key_info1 suggests the upper nybble is being extracted however the following shift of 8 bits is too large and always results in 0. Fix this by shifting only by 4 bits to correctly get the upper nybble. Detected by CoverityScan, CID#142891 ("Operands don't affect result") Fixes: fa590c22 ("staging: rts5208: add support for rts5208 and rts5288") Signed-off-by:Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Xiangyang Zhang authored
space required before the open parenthesis, open brace should be on previous line. Signed-off-by:
Xiangyang Zhang <xyz.sun.ok@gmail.com> Signed-off-by:
-
Jamie Huang authored
checkpatch.pl gave ERROR: open brace '{' following function definitions go on the next line. Signed-off-by:Jamie Huang <jamienstar@163.com> Signed-off-by:
-
Dan Carpenter authored
We want to concatonate join string one, a '/' character, string two and then a NUL terminator. The destination buffer holds ori_gf->gf_pathlen characters. The strlen() function returns the number of characters not counting the NUL terminator. So we should be adding two extra spaces, one for the foward slash and one for the NUL. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
John L. Hammond <john.hammond@intel.com> Reviewed-by:
frank zago <fzago@cray.com> Signed-off-by:
-
Greg Kroah-Hartman authored
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: Second set of IIO new device support, features and cleanup for the 4.14 cycle. New device support: * ak8974 - support the AMI306. * st_magnetometer - add support for the LIS2MDL with bindings. * rockchip-saradc - add binding for rv1108 SoC (no driver change). * srf08 - add srf02 (i2c only) and srf10 support. * stm32-timer - support for the STM32H7 to existing driver. Features: * tools - move over to the tools buildsystem rather than hand rolling. - add an install section to the build. * ak8974 - use serial number to add device randomness. - add AMI306 calibration data output. * ccs811 - triggered buffer support. * srf08 - add a device tree table as the old style i2c probing is going away, - add triggered buffer support * st32-adc - add optional st,min-sample-time-nsecs binding to allow control of sampling against analog circuitry. * stm32-timer - add output compare triggers. * ti-ads1015 - add threshold event support. * ti-ads7950 - Allow use on ACPI platforms including providing a default reference voltage as there is no way to obtain this on ACPI currently. Cleanup and fixes: * ad7606 - fix an error return code in probe. * ads1015 - fix incorrect data rate setting update when capture in progress, - fix wrong scale information for the ADS1115, - make conversions work when CONFIG_PM is not set, - make sure we don't get a stale result after a runtime resume by ensuring we wait long enough, - avoid returning a false error form the buffer setup callbacks, - add enough wait time to get the correct conversion, - remove an unnecessary config register update, - add a helper to set conversion mode reducing repeated boilerplate, - use devm_iio_triggered_buffer_setup to simplify error and remove paths, - use iio_device_claim_direct_mode instead of opencoding the same. * ak8974 - mark the INT_CLEAR register as precious to prevent debugfs access. * apds9300 - constify the i2c_device_id. * at91-sama5 adc - add missing Kconfig dependency. * bma180 accel - constify the i2c_device_id. * rockchip_saradc - explicitly request exclusive reset control as part of the reset rework on going throughout the kernel. * st_accel - fix drdy configuration for a load of accelerometers that only have the int1 line. Fix is unimportant as presumably no deviec tree actually used the non existent hardware line. * st_pressure - fix drdy configuration for LPS22HB and LPS25H by dropping int2 support as they don't have this. Fix is unimportant as presumably no device tree actually used the non existent hardware line. * stm32-dac - explicitly request exclusive reset control (part of reset being reworked). * tsl2583 - constify the i2c_device_id. * xadc - coding style fixes.
-
Philipp Zabel authored
Commit a53e35db ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Heiko Stuebner <heiko@sntech.de> Cc: linux-iio@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Philipp Zabel authored
Commit a53e35db ("reset: Ensure drivers are explicit when requesting reset lines") started to transition the reset control request API calls to explicitly state whether the driver needs exclusive or shared reset control behavior. Convert all drivers requesting exclusive resets to the explicit API call so the temporary transition helpers can be removed. No functional changes. Cc: Jonathan Cameron <jic23@kernel.org> Cc: Hartmut Knaack <knaack.h@gmx.de> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: linux-iio@vger.kernel.org Signed-off-by:
-
Akinobu Mita authored
The ADS1015 device provides programmable comparator that can issue an interrupt on the ALERT pin. This change adds the iio threshold event support for that feature. The ADS1015 device only have a single config register which contains an input multiplexer selection, comparator settings, and etc. So only a single event channel can be enabled at a time. Also enabling both buffer and event are prohibited for simplicity. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Akinobu Mita authored
While the iio buffer for the ti-ads1015 driver is enabled, reading the raw ADC channel data is restricted. We usually use the iio_device_claim_direct_mode()/iio_device_release_direct_mode() pair for that. This change consequently reverses the locking order for the driver's private lock and indio_dev->mlock which acquired by iio_device_claim_direct_mode() internally. But it's safe because there is no other dependency between these locks. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Akinobu Mita authored
Use devm_iio_triggered_buffer_setup to simplify the error path in the probe() and remove() function. This changes the remove order, but the end result of remove function actually does the reverse of probe. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Akinobu Mita authored
This adds a helper function to set conversion mode as there are a fair number of users. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Akinobu Mita authored
The ti-ads1015 driver has eight iio voltage channels and each iio channel can hold own scale information. The ADS1015 device only have a single config register which contains an input multiplexer selection, PGA and data rate settings. So the driver should load the correct settings when the input multiplexer selection is changed. However, regardless of which channlel is currently selected, changing any iio channel's scale information immediately overwrites the current PGA setting in the config register. It is harmless because the correct PGA settings are reloaded just before getting adc result anyway. But it is unnecessary register update and should be removed. Cc: Daniel Baluta <daniel.baluta@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Akinobu Mita authored
This driver assumes that the device is operating in the continuous conversion mode which performs the conversion continuously. So this driver inserts a wait time before reading the conversion register if the configuration is changed from a previous request. Currently, the wait time is only the period required for a single conversion that is calculated as the reciprocal of the sampling frequency. However we also need to wait for the the previous conversion to complete. Otherwise we probably get the conversion result for the previous configuration when the sampling frequency is lower. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Akinobu Mita authored
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on success, 1 if the device's runtime PM status was already requested status or error code on failure. So a positive return value doesn't indicate an error condition. However, any non-zero return values from buffer preenable and postdisable callbacks are recognized as an error and this driver reuses the return value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in these callbacks. This change fixes the false error detections. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Akinobu Mita authored
This driver assumes that the device is operating in the continuous conversion mode which performs the conversion continuously. So this driver doesn't insert a wait time before reading the conversion register if the configuration is not changed from a previous request. This assumption is broken if the device is runtime suspended and entered a power-down state. The forthcoming request causes reading a stale result from the conversion register as the device is runtime resumed just before. Fix it by adding a flag to detect that condition and insert a necessary wait time. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Akinobu Mita authored
The ADS1015 device have two operating modes, continuous conversion mode and single-shot mode. This driver assumes that the continuous conversion mode is selected by runtime resume callback when the ADC result is requested. If CONFIG_PM is disabled, the device is always in the default single-shot mode and no one begins a single conversion. So the conversion register doesn't contain valid ADC result. Fix it by changing the continuous mode in probe function. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Akinobu Mita authored
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same scale information is used for both devices in this driver, however they have actually different values and the ADS1115's one is not correct. These devices have the same full-scale input voltage range for each PGA selection. So instead of adding another hardcoded scale information, compute a correct scale on demand from each device's resolution. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Akinobu Mita authored
The ti-ads1015 driver has eight iio voltage channels and each iio channel can hold own sampling frequency information. The ADS1015 device only have a single config register which contains an input multiplexer selection, PGA and data rate settings. So the driver should load the correct settings when the input multiplexer selection is changed. However, regardless of which channlel is currently selected, changing any iio channel's sampling frequency information immediately overwrites the current data rate setting in the config register. It breaks the current data rate setting if the different channel's sampling frequency information is changed because the data rate setting is not reloaded when the input multiplexer is switched. This removes the unexpected config register update and correctly load the data rate setting before getting adc result. Cc: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
-
Andy Shevchenko authored
ACPI enabled platforms do not have a mean of regulators. Instead we use hard coded voltage value for reference pin. When value is 0 (default) we fall back to request a regulator. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Michał Mirosław authored
Use AMI306 calibration data for randomness and debugging. Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Michał Mirosław authored
Reading INT_CLEAR has side effects - disallow reading it via debugfs. Signed-off-by:
-
Michał Mirosław authored
Mix device-specific data into randomness pool. Signed-off-by:
-
Michał Mirosław authored
Add support for AMI306 magnetometer - very similar to AMI305. Signed-off-by:
-
Arvind Yadav authored
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
-
Arvind Yadav authored
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by:
-
Arvind Yadav authored
i2c_device_id are not supposed to change at runtime. All functions working with i2c_device_id provided by <linux/i2c.h> work with const i2c_device_id. So mark the non-const structs as const. Signed-off-by:
-
- 19 Aug, 2017 4 commits
-
-
Cihangir Akturk authored
The config_log_add() function first calls config_log_put() with the variable 'cld' and then jumps to label 'out_cld', which will call the same function with the same 'cld' variable. However, at this point, 'cld' might have been already freed by the first invocation of config_log_put(). Even if we remove the invocation at that point, we will still get into trouble. This is because, in the error path, just below the label 'out_cld', we try to put 'params_cls' and 'sptlrpc_cld', which might also have been freed by config_log_put(). The point is that, config_llog_data::cld_sptlrpc and config_llog_data::cld_params members are assigned at the beginning of this function. To avoid this, do not call config_log_put() inside the else block, immediately jump to 'out_cld' instead. Moreover, remove assignments to config_llog_data::cld_sptlrpc and config_llog_data::cld_params at the beginning, since we already assign them below in the function with 'cld_lock' held. As an additional benefit, code size gets smaller. before: text data bss dec hex filename 26188 2256 4208 32652 7f8c drivers/staging/lustre/lustre/mgc/mgc_request.o after: text data bss dec hex filename 26092 2256 4208 32556 7f2c drivers/staging/lustre/lustre/mgc/mgc_request.o Signed-off-by:
Cihangir Akturk <cakturk@gmail.com> Reviewed-by:
James Simmons <jsimmons@infradead.org> Signed-off-by:
-
Bhumika Goyal authored
Declare echo_lock_ops object of type cl_lock_operations as const as it is only passed to the function cl_lock_slice_add. The corresponding argument is of type const, so make the object const. Signed-off-by:
-
David Wittman authored
Declare fiemap_for_stripe as static to fix sparse warnings: > warning: symbol 'fiemap_for_stripe' was not declared. Should it be > static? Signed-off-by:
David Wittman <dwittman@gmail.com> Acked-by:
-
NeilBrown authored
Fix minor typos in comments. Signed-off-by:
NeilBrown <neilb@suse.com> Acked-by:
-
- 18 Aug, 2017 9 commits
-
-
Badhri Jagan Sridharan authored
While in SNK_READY state, the explicit_contract seems to be set to true irrespective of whether an explicit contract was established for the current connection. TCPM also seems to report the pwr_opmode as TYPEC_PWR_MODE_PD always once the port gets into SNK_READY state. This isn't completely true as port gets into the SNK_READY state for non-pd type-c ports as well. This patch sets the explicit_contract flag only when the PS_READY message is received and the vbus has been detected by the port controller. Signed-off-by:
Badhri Jagan Sridharan <Badhri@google.com> Signed-off-by:
-
Shreeya Patel authored
Alignment should match with open parenthesis. This fixes the coding style issue. Signed-off-by:
Shreeya Patel <shreeya.patel23498@gmail.com> Reviewed-by:
Bryan O'Donoghue <pure.logic@nexus-software.ie> Signed-off-by:
-
Okash Khawaja authored
When an external USB synth is unplugged while the module is loaded, we get a null pointer deref. This is because the tty disappears while speakup tries to use to to communicate with the synth. This patch fixes it by checking tty for null before using it. Since tty can become null between the check and its usage, a mutex is introduced. tty usage is now surrounded by the mutex, as is the code in speakup_ldisc_close which sets the tty to null. The mutex also serialises calls to tty from speakup code. In case of tty being null, this sets synth->alive to zero and restarts ttys in case they were stopped by speakup. Signed-off-by:
Okash Khawaja <okash.khawaja@gmail.com> Reviewed-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by:
-
Okash Khawaja authored
Testing has shown that lp* devices don't work correctly with speakup just yet. That will require some additional work. Until then, this patch removes code related to that. Signed-off-by:
-
Gustavo A. R. Silva authored
platform_get_irq() returns an error code, but the dim2_hdm driver ignores it and always returns -ENODEV. This is not correct and, prevents -EPROBE_DEFER from being propagated properly. Also, notice that platform_get_irq() no longer returns 0 on error: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af Print and propagate the return value of platform_get_irq on failure. This issue was detected with the help of Coccinelle. Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
-
Ricardo Silva authored
The 'linkstatus' field from struct 'hfa384x_link_status' represents a 16-bit little-endian integer, so declare it as such to avoid the following sparse warning when accessing it through the 'le16_to_cpu()' function: prism2sta.c:1450:31: warning: cast to restricted __le16 Signed-off-by:
Ricardo Silva <rjpdasilva@gmail.com> Signed-off-by:
-
AbdAllah-MEZITI authored
The same structure is used in both side, so we dont need to cast. This will fix the following sparse warnings: drivers/staging/wlan-ng/prism2sta.c:1139:13: warning: cast to restricted __le16 drivers/staging/wlan-ng/prism2sta.c:1150:24: warning: cast to restricted __le16 drivers/staging/wlan-ng/prism2sta.c:1157:37: warning: cast to restricted __le16 drivers/staging/wlan-ng/prism2sta.c:1158:37: warning: cast to restricted __le16 drivers/staging/wlan-ng/prism2sta.c:1159:40: warning: cast to restricted __le16 drivers/staging/wlan-ng/prism2sta.c:1450:31: warning: cast to restricted __le16 Signed-off-by:
AbdAllah MEZITI <abdallah.meziti.pro@gmail.com> Signed-off-by:
-
Lynn Lei authored
Fixed a potential memory leak inside skb_ether_to_p80211() When the wep_encrypt() fails the code return 2 directly Which causes the p80211_wep->data dangling Add a kfree statement to reclaim that memory allocated Signed-off-by:
Lynn Lei <lynnl.yet@gmail.com> Signed-off-by:
-
John Smith authored
ethernet-rx.c: fix WARNING: line over 80 characters The code was restructured a bit, a helper function was added to cvm_oct_poll. Signed-off-by:
John Smith <catalinnow@gmail.com> Signed-off-by:
-
