As discussed on irc, I'm sending a pull request with one important change:

- Disable support for 32-bit user processes. This is done due to AMD's decision
  to remove support for 32-bit user processes on Linux for its HSA stack.

* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
  amdkfd: Disable support for 32-bit user processes

Linux 3.18

Backmerge Linus tree into -next as we had conflicts in i915/radeon/nouveau,
and everyone was solving them individually.

* tag 'v3.18': (57 commits)
  Linux 3.18
  watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7
  uapi: fix to export linux/vm_sockets.h
  i2c: cadence: Set the hardware time-out register to maximum value
  i2c: davinci: generate STP always when NACK is received
  ahci: disable MSI on SAMSUNG 0xa800 SSD
  context_tracking: Restore previous state in schedule_user
  slab: fix nodeid bounds check for non-contiguous node IDs
  lib/genalloc.c: export devm_gen_pool_create() for modules
  mm: fix anon_vma_clone() error treatment
  mm: fix swapoff hang after page migration and fork
  fat: fix oops on corrupted vfat fs
  ipc/sem.c: fully initialize sem_array before making it visible
  drivers/input/evdev.c: don't kfree() a vmalloc address
  cxgb4: Fill in supported link mode for SFP modules
  xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
  mm/vmpressure.c: fix race in vmpressure_work_fn()
  mm: frontswap: invalidate expired data on a dup-store failure
  mm: do not overwrite reserved pages counter at show_mem()
  drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
  ...

Conflicts:
	drivers/gpu/drm/i915/intel_display.c
	drivers/gpu/drm/nouveau/nouveau_drm.c
	drivers/gpu/drm/radeon/radeon_cs.c

Pull libata fixes from Tejun Heo:
 "Three libata fixes for v3.18.  Nothing too interesting.  PCI ID ID and
  quirk additions to ahci and an error handling path fix in sata_fsl"

* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: disable MSI on SAMSUNG 0xa800 SSD
  sata_fsl: fix error handling of irq_of_parse_and_map
  AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller

Pull watchdog fix from Wim Van Sebroeck:
 "Fix the watchdog mask bit offset for Exynos7"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: s3c2410_wdt: Fix the mask bit offset for Exynos7

Pull i2c fixes from Wolfram Sang:
 "Here are two more driver bugfixes for I2C which would be good to have"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: cadence: Set the hardware time-out register to maximum value
  i2c: davinci: generate STP always when NACK is received

This patch checks if the process that opens the /dev/kfd device is 32-bit
process. If so, it returns -EPERM and prints a warning message in dmesg.

This is done to prevent 32-bit user processes from using amdkfd, and hence, HSA
features.

AMD's HSA userspace stack will also support only 64-bit processes on Linux.
Reviewed-by: Alexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>

The watchdog mask bit offset listed for Exynos7 is incorrect.
Fix this.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Naveen Krishna Chatradhi <naveenkrishna.ch@gmail.com
Reviewd-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Pull x86 fixes from Thomas Gleixner:
 "Two final fixlets for 3.18:
   - Prevent microcode reload wreckage on 32bit
   - Unbreak cross compilation"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, microcode: Limit the microcode reloading to 64-bit for now
  x86: Use $(OBJDUMP) instead of plain objdump

Pull sound fixlet from Takashi Iwai:
 "Just one commit for adding a copule of HD-audio quirk entries"

* tag 'sound-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Add headset Mic support for new Dell machine

Pull drm intel fixes from Dave Airlie:
 "Two intel stable fixes, that should be it from me for this round"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: Unlock panel even when LVDS is disabled
  drm/i915: More cautious with pch fifo underruns

Pull ACPI backlight fix from Rafael Wysocki:
 "This is a simple fix for an ACPI backlight regression introduced by a
  recent commit that overlooked a corner case which should have been
  taken into account"

* tag 'pm+acpi-3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / video: update condition to check if device is in _DOD list

Silence some pch fifo underrun reports and panel locking backtraces,
both cc: stable.

* tag 'drm-intel-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Unlock panel even when LVDS is disabled
  drm/i915: More cautious with pch fifo underruns

Merge tag 'drm-intel-next-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel into drm-next

Fixes for 3.20. I did stick the gen3/4 reset work from Ville in because we
have an awful lot of gen4 mesa hangs, and with this reset should also work
on vintage i965g/gm (we already have reset for g4x/gen4.5). So should help
to appease users suffering from these hangs. Otherwise all over.

This is the last 3.20 pull from me, from here on Jani will take over. By Ville Syrjälä (8) and others
* tag 'drm-intel-next-fixes-2014-12-04' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Reject modeset when the same digital port is used more than once
  drm/i915: mask RPS IRQs properly when disabling RPS
  drm/i915: Tune down spurious CRC interrupt warning
  drm/i915: Fix context object leak for legacy contexts
  drm/i915/skl: Update in Gen9 multi-engine forcewake range
  drm/i915/eDP: When enabling panel VDD cancel pending disable worker
  drm/i915: Handle runtime pm in the CRC setup code
  drm/i915: Disable crtcs gracefully before GPU reset on gen3/4
  drm/i915: Grab modeset locks for GPU rest on pre-ctg
  drm/i915: Implement GPU reset for g33
  drm/i915: Implement GPU reset for 915/945
  drm/i915: Restore the display config after a GPU reset on gen4
  drm/i915: Fix gen4 GPU reset
  drm/i915: Stop gathering error states for CS error interrupts
  drm/i915: Disallow pin ioctl completely for kms drivers
  drm/i915: Only warn the first time we attempt to mmio whilst suspended
  drm/i915/chv: Enable AVI, SPD and HDMI infoframes for CHV.
  drm/i915: Don't clobber crtc->new_config when nothing changes

Just three more fixes for 3.19.
This is the last request until -rc1. I will have our QA team run a full
HSA stack test on 3.19-rc1 and if we find problems, I will send a fixes pull
request.

* 'amdkfd-next-3.19' of git://people.freedesktop.org/~gabbayo/linux:
  amdkfd: Set *buffer_ptr to NULL in case of error
  amdkfd: use atomic allocations within srcu callbacks
  amdkfd: use sizeof(long) granularity for the pasid bitmask

- More cursor and hotspot handling fixes
- Fix some typos in the new smc fan control code and enable on CI
- VM and CS cleanups

* 'drm-next-3.19-wip' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: enable smc fan control on CI
  drm/radeon: use pointers instead of indexes for CS chunks
  drm/radeon: remove duplicates check
  drm/ttm: optionally move duplicates to a separate list
  drm/radeon: check the right ring in radeon_evict_flags()
  drm/radeon: fix copy paste typos in fan control for si/ci
  drm/radeon: Hide cursor on CRTCs used by fbdev (v2)
  drm/radeon: add spinlock for BO_VA status protection (v2)
  drm/radeon: fence PT updates as shared
  drm/radeon: rename radeon_cs_reloc to radeon_bo_list
  drm/radeon: drop the handle from radeon_cs_reloc
  drm/radeon drop gobj from radeon_cs_reloc
  drm/radeon: fix typo in new fan control registers for SI/CI
  drm/radeon: sync all BOs involved in a CS
  drm/radeon: Move hotspot handling out of radeon_set_cursor
  drm/radeon: Re-show the cursor after a modeset

Pull media fixes from Mauro Carvalho Chehab:
 "A core fix and some driver fixes:
   - regression fix in Remote Controller core affecting RC6 protocol
     handling
   - fix video buffer handling in cx23885
   - race fix in solo6x10
   - fix image selection in smiapp
   - fix reported payload size on s2255drv
   - two updates for MAINTAINERS file"

* tag 'media/v3.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] rc-core: fix toggle handling in the rc6 decoder
  MAINTAINERS: Update mchehab's addresses
  [media] cx23885: use sg = sg_next(sg) instead of sg++
  [media] s2255drv: fix payload size for JPG, MJPEG
  [media] Update MAINTAINERS for solo6x10
  [media] solo6x10: fix a race in IRQ handler
  [media] smiapp: Only some selection targets are settable

A typo "header=y" was introduced by commit 7071cf7f ("uapi: add
missing network related headers to kbuild").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.

Hence, fix it by generating Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Just like 0x1600 which got blacklisted by 66a7cbc3 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled.  Disable MSI.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Cc: stable@vger.kernel.org

In function acquire_packet_buffer() we may return -ENOMEM. In that case, we
should set the *buffer_ptr to NULL, so that calling functions which check the
*buffer_ptr value as a criteria for success, will know that
acquire_packet_buffer() failed.
Reviewed-by: Alexey Skidanov <alexey.skidanov@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>

It appears that some SCHEDULE_USER (asm for schedule_user) callers
in arch/x86/kernel/entry_64.S are called from RCU kernel context,
and schedule_user will return in RCU user context.  This causes RCU
warnings and possible failures.

This is intended to be a minimal fix suitable for 3.18.
Reported-and-tested-by: Dave Jones <davej@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This seems to work well on CI boards after fixing the
last few bugs noticed by Chernovsky Oleg.

On boards with a high default fan speed this should
reduce fan noise.  Manual fan control is not enabled
yet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Nobody is interested at which index the chunk is. What's needed is
a pointer to the chunk. Remove unused chunk_id field as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Completely unnecessary since the ww_mutex used to reserve a buffer
can detect double reservations from the same thread anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch adds an optional list_head parameter to ttm_eu_reserve_buffers.
If specified duplicates in the execbuf list are no longer reported as errors,
but moved to this list instead.
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Check the that ring we are using for copies is functional
rather than the GFX ring.  On newer asics we use the DMA
ring for bo moves.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Pull i2c bugfixes from Wolfram Sang:
 "A few driver bugfixes for 3.18"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: omap: fix i207 errata handling
  i2c: designware: prevent early stop on TX FIFO empty
  i2c: omap: fix NACK and Arbitration Lost irq handling

Pull PCI fix from Bjorn Helgaas:
 "This fixes a Tegra20 regression that we introduced during the v3.18
  merge window"

* tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: tegra: Use physical range for I/O mapping

Pull devicetree bugfix from Grant Likely:
 "One more bug fix for v3.18.  I debated whether or not to send you this
  merge request because we're at such a late rc.  The bug isn't critical
  in that there is only one system known to be affected and the patch is
  easy to backport.  The codepath is used by pretty much every DT based
  system, so there is risk a of regression (it /should/ be safe, but
  I've been bitten by stuff that should be safe before).  I've had it in
  linux-next for a week and haven't received any complaints.

  I think it probably should just be merged right away rather than
  waiting for the merge window and backporting.  It does fix a real bug
  and the code is theoretically safer after the change.  I can't think
  of any situation where it would be dangerous to reserve the DT memory
  an extra time.

  Summary from tag:

    Single bugfix for boot failure seen in the wild.  The memory reserve
    code tries to be clever about reserving the FDT, but it should just
    go ahead and reserve it unconditionally to avoid the problem of
    partial overlap described in the patch"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
  of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap

Pull block core regression fix from Jens Axboe:
 "Single fix for a regression introduced in this development cycle,
  where dm on top of dif/dix is broken.  From Darrick Wong"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix regression where bio_integrity_process uses wrong bio_vec iterator

Pull drm fixes from Dave Airlie:
 "Radeon and Nouveau fixes:

  So nouveau had a few regression introduced, Ben and Maarten finally
  tracked down the one that was causing problems on my MacBookPro, also
  nvidia gave some info on the an engine we were using incorrectly, so
  disable our use of it, and one regresion with pci hotplug affecting
  optimus users.

  Radeon has an oops fixs, sync fix, and one workaround to avoid broken
  functionality on 32-bit x86, this needs better root causing and a
  better fix, but the bandaid is a lot safer at this point"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
  drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
  drm/radeon: sync all BOs involved in a CS v2
  nouveau: move the hotplug ignore to correct place.
  drm/nouveau/gf116: remove copy1 engine
  drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
  drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it

Pull networking fixes from David Miller:

 1) Fill in ethtool link parameters for all link types in cxgb4, from
    Hariprasad Shenai.

 2) Fix probe regressions in stmmac driver, from Huacai Chen.

 3) Network namespace leaks on errirs in rtnetlink, from Nicolas
    Dichtel.

 4) Remove erroneous BUG check which can actually trigger legitimately,
    in xen-netfront.  From Seth Forshee.

 5) Validate length of IFLA_BOND_ARP_IP_TARGET netlink attributes, from
    Thomas Grag.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  cxgb4: Fill in supported link mode for SFP modules
  xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
  sh_eth: Fix sleeping function called from invalid context
  stmmac: platform: Move plat_dat checking earlier
  sh_eth: Fix skb alloc size and alignment adjust rule.
  rtnetlink: release net refcnt on error in do_setlink()
  bond: Check length of IFLA_BOND_ARP_IP_TARGET attributes

Since we are now preserving the cursor across modesets, the cursor could
be left over in console if e.g. X crashed.

v2: add comment about universal plane support
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Stop using the VM mutex for this

v2: fix typo in comment
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The BO_VA contains everything necessary.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Better match what it is actually doing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It's only used for duplicate check and that
can be done on the original as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>