If recovery is called when the FW is off, we should clear the recovery
flag. Otherwise we risk booting the driver in permanent pending-recovery
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Don't read the FW panic log or print other debug data when recovery is
intended (i.e. FW type switch). This takes valuable time and can be
confusing to the user.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

This command is buggy (doesn't take the mutex) and unused. Instead, the
"start_recovery" file is used for the same purpose. Remove the code but
keep the command constant to avoid breaking the testmode ABI.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

If a Tx queue is currently stopped because of our Tx watermark flow
control, don't stop it again. This causes a warning to appear.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

Refuse to boot if the FW version is too old. The minimum version is set
per chip, with the option of setting it per PG in the future.

When boot fails because of an old FW, display a helpful message.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

New wl12xx firmware supports scheduled scans also while connected.
Stop blocking sched scan requests when connected and add a quirk to
block in hardware that don't support it (currently wl18xx doesn't).

This requires FW version 6/7.3.10.2.112 for single-role and
6/7.5.6.0.25 for multi-role.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

They both can potentially be NULL.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Some devices (e.g. Sony's PaSoRi) can not do type B polling, so we have
to make a distinction between ISO14443 type A and B poll modes.

Cc: Eric Lapuyade <eric.lapuyade@intel.com>
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Otherwise DATA_EXCHANGE seems to be just fine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Sony RC-S360 is also known as the Sony PaSoRi contactless reader.
Only type 2, 3 and 4 tag reading is supported at the moment.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We check for the polling flag before checking if the netlink PID caller
match.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The socket local pointer can be NULL when a socket is created but never
bound or connected.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When receiving such frame, the sockets waiting for a connection to finish
should be woken up. Connecting to an unbound LLCP service will trigger a
DM as a response.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

With the LLCP 16 local SAPs we can potentially quickly run out of source
SAPs for non well known services.
With the so called late binding we will reserve an SAP only when we actually
get a client connection for a local service. The SAP will be released once
the last client is gone, leaving it available to other services.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

With not Well Known Services there is no guarantees as to which
SSAP the server will be listening on, so there is no reason to
support binding to a specific source SAP.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch fixes a typo and return the correct error when trying to
bind 2 sockets to the same service name.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The LLCP SAP should only be freed when the socket owning it is released.
As long as the socket is alive, the SAP should be reserved in order to
e.g. send the right wks array when bringing the MAC up.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When the MAC link goes down, we should only keep the bound sockets
alive. They will be closed by sock_release or when the underlying
NFC device is moving away.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Drivers will need them before starting a poll or when being activated
as targets. Mostly WKS can have changed between device registration and
then so we need to re-build the whole array.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Set the right target index and use a better socket declaration routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Getting a valid CONNECT means we have a valid target index.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Some NFC chips will statically create and open pipes for both standard
and proprietary gates. The driver can now pass this information to HCI
such that HCI will not attempt to create and open them, but will instead
directly use the passed pipe ids.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If the device is polling we sent a 0 target found event.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The semantics for a zero target found event is that the polling operation
could not complete.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

There can ever be only one call to nfc_targets_found() after polling
has been engaged. This could be from a target discovered event from
the driver, or from an error handler to notify poll will never complete.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If there is an ongoing HCI command executing, it will be completed,
thereby pushing the error up to the core. Otherwise, HCI will directly
notify the core with the error.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

HCI cmd can be completed either from an HCI response or from an
internal driver or HCI error. This requires to factorize the
completion code outside of the device lock.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This API should be used by drivers, HCI, SHDLC or NCI stacks to report an
unrecoverable error.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

An HCI command can complete either from an HCI response
(with an HCI result) or as a consequence of any other system
error during processing. The completion therefore needs to take
a standard errno code. The HCI response will convert its result
to a standard errno before calling the completion.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We can now report an ENOMEM error up to the HCI layer.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

nfc_hci_recv_frame can not be called with a NULL skb.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

shdlc reset may leave HCI in an inconsistent state by loosing parts of
HCI frames. Handle this case by reporting an unrecoverable error to HCI.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The questions asked in the comments have been answered and addressed.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.

Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>