At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add code to display driver version information in dmesg after
loading the driver successfully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The SDIO card is now fully powered down when the network interface is
brought down.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Modify the driver so that it does not function when the interface is
down, in preparation for runtime power management.

No commands can be run while the interface is down, so the ndo_dev_stop
routine now directly does all necessary work (including asking the device
to disconnect from the network and disabling multicast functionality)
directly.

power_save and power_restore hooks are added meaning that card drivers
can take steps to turn the device off when the interface is down.

The MAC address can now only be changed when all interfaces are down;
the new address will be programmed when an interface gets brought up.
This matches mac80211 behaviour.

Also, some small cleanups/simplifications were made in the surrounding
device handling logic.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some drivers (ath9k for example) are using skb->protocol to treat EAPOL
frames somehow special (disallow aggregation for example).

When running in AP mode hostapd injects the EAPOL frames through a
monitor interface and thus skb->protocol isn't set at all. Hence, if the
injected frame is a data frame and carries a rfc1042 headaer update the
skb->protocol field accordingly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Several uses were missing terminating newlines.
Typo fix and macro neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No need to process RxDone and ds_info status again in case
valid rx status is given.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch cleanups virtual wiphy specific frametype structure
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/modal_eeprom
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/base_eeprom
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This ieee80211 core was found on a Netgear wndr3400.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

They are SPROM specific, so all should be defined in ssb code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently ath9k presents the internal calibrated noise floor as channel
noise measurement, however this results in highly chip specific values
that are only useful as relative measurements but do not resemble any
real channel noise values.

In order to give a much better approximation of the real channel noise,
add the difference between the measured noise floor and the nominal
chip specific noise floor to the default minimum channel noise value,
which is currently used to calculate the signal strength from the RSSI
value. This may not be 100% accurate, but it's much better than what's
there before.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make mesh_preq_queue_lock locking consistent with mesh_queue_preq() using
spin_lock_bh().
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

OLPC power management code has recently gone upstream. This piece
completes the puzzle for libertas_usb, which now programs the OLPC EC
for wlan wakeups when they have been requested.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When testing for tx power, bypass the default limits.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use the previously calculated maximum of all rates instead of just the one
from the lowest rate of the selected PHY mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is always 0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove unnecessary includes from base.h.  Add includes to other files as
necessary.  Don't include base.h unless needed.

Move declarations for functions in base.c from ath5k.h to base.h.

Use a better named define to protect base.h against double inclusion.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01"
as the third product ID.  Those have Agere firmware.

With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be
assumed to have Intersil firmware.  Cards with Agere firmware use
"Version 01.01".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is needed to match wireless cards with Intersil firmware that have
ID 0x0156:0x0002 and the third ID "Version 01.02".  Such cards are
currently matched by orinoco_cs, which doesn't support WPA.  They should
be matched by hostap_cs.

The first and the second product ID vary widely, so there are few users
with some particular IDs.  Of those, very few can submit a patch for
hostap_cs or write a useful bugreport.  It's still important to support
their hardware properly.

With PCMCIA_DEVICE_MANF_CARD_PROD_ID3, it should be possible to cover
the remaining Intersil based designs that kept the numeric ID and the
"version" of the reference design.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

According to 802.11-2007, 7.3.1.14 it is compliant to use a buf_size of
0 in ADDBA requests. But some devices (AVM Fritz Stick N) arn't able to
handle that correctly and will reply with an ADDBA reponse with a
buf_size of 0 which in turn will disallow BA sessions for these
devices.

To work around this problem, initialize hw.max_tx_aggregation_subframes
to the maximum AMPDU buffer size 0x40.

Using 0 as default for the bufsize was introduced in commit
5dd36bc9 (mac80211: allow advertising
correct maximum aggregate size).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If we receive an ADDBA response with status code 0 and a buf_size of 0
we should stop the TX BA session as otherwise we'll end up queuing
frames in ieee80211_tx_prep_agg forever instead of sending them out as
non AMPDUs.

This fixes a problem with AVM Fritz Stick N wireless devices where
frames to this device are not transmitted anymore by mac80211.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Devices supported by b43legacy don't support 64-bit DMA.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for v2 of enhanced sensitivity table for 2000 series products
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>