- 18 May, 2015 40 commits
-
-
Jemma Denson authored
Algorithm copied from cx24117.c - it seems to work. Showing 95% on a signal I know to be somewhere around 74dBuV. [mchehab@osg.samsung.net: merged two patches, to avoid breaking compilation] Signed-off-by:
Jemma Denson <jdenson@gmail.com> Signed-off-by:
Patrick Boettcher <patrick.boettcher@posteo.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Jemma Denson authored
This patch changes DVBv3 signal strength to read from the cache by moving the signal strength reading routine into get_stat, and reducing read_signal_strength to just returning the cached value. Signed-off-by:
-
Jemma Denson authored
get_frontend was making a call to read_status, which is being called periodically anyway. Have read_status store fe_status in the state struct instead and use that within get_frontend. Signed-off-by:
-
Jemma Denson authored
Previous patch added in collection, this patch enables them by signalling they are available. Signed-off-by:
-
Jemma Denson authored
Add new get_stats function, called from read_status, for collecting DVBv5 stats into the frontend cache. Only signal strength for now, can add others later. Not currently marked as available, future patch will enable. Signed-off-by:
-
Jemma Denson authored
Change calculate_vco function to send_vco to tidy up cx24120_init function. xxyyzz variable is remnants of a manual div & remainder codepath to perform a u64 rounded div; replace with kernel macro DIV_ROUND_CLOSEST_ULL Hex values provided to the message are mainly variables calculated within this function, replace with these to remove hardcoding. Signed-off-by:
-
Jemma Denson authored
msg.len has been ++'d so msg.len is one too many. Signed-off-by:
-
Jemma Denson authored
This patch adds in a missing command to cx24120_check_cmd. This part of the old reverse engineered driver was quite hard to follow - it's presumed the compiler did some neat optimisation that wasn't easy to decode. This command was checked for in that version but not copied across to the new switch statement. For reference, old reverse engineered code: xxzz = cmd->id - 0x11; // look for specific message id if ( xxzz <= 0x13 ) { msg_cmd_mask = 1 << xxzz; //0x0F8021 // if cmd_id 17 or 22 or 33-36, 42, 47, 57-61 etc. disable mpeg output if ( msg_cmd_mask & 0x0F8021 ) { // 000011111000000000100001b cx24120_msg_mpeg_output_global_config(state, 0); msleep(100); state->dvb_s2_mode &= 0xFD; // reset mpeg out enable flag } } Signed-off-by: -
Jemma Denson authored
This patch removes the requirement of waiting for tune in set_frontend by moving the clock set call into read_status Signed-off-by:
-
Jemma Denson authored
This patch changes DVB-S/DVB-S2 to the more commonly used DVB-S/S2 in the description for DVB_CX24120 Signed-off-by:
-
Patrick Boettcher authored
This patches fixes all checkpatch-errors. Even the ones created --strict. Signed-off-by:
-
Patrick Boettcher authored
Mauro pointed out some coding style issues in his review. This patch fixes them. Signed-off-by:
-
Patrick Boettcher authored
Add maintainer for the cx24120 frontend-driver. Signed-off-by:
-
Patrick Boettcher authored
Some i2c-hosts are quite limited regarding maximum i2c-burst-write-sizes. This patch makes the previously hardcoded field configurable by users of the driver. Signed-off-by:
-
Patrick Boettcher authored
This patch fixes printk-related checkpatch warnings. All printks have been converted to pr_warn or pr_info or pr_err. Signed-off-by:
-
Jemma Denson authored
This patch adds support for the Technisat Skystar S2 - this has been tried before but the cx24120 driver was a bit out of shape and it didn't got any further: https://patchwork.linuxtv.org/patch/10575/ It is an old card, but currently being sold off for next to nothing, so it's proving quite popular of late. Noticing it's quite similar to the cx24116 and cx24117 I've rewritten the driver in a similar way. There were a few registers and commands from those drivers missing from this one I've tested out and found they do something so they've been added in to speed up tuning and to make get_frontend return something useful. Signed-off-by:
-
Hans Verkuil authored
Missing varlistentry tags. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
Explain which clock was used to make the timestamp. Signed-off-by:
-
Hans Verkuil authored
Looks ugly, a space before a period at the end of a sentence. Remove it. Signed-off-by:
-
Hans Verkuil authored
Even though the rcar-vin driver tells userspace that it will give a monotonic timestamp, it is actually using gettimeofday. Replace this with a proper monotonic timestamp. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Hans Verkuil authored
V4L2 drivers should use MONOTONIC timestamps instead of gettimeofday, which is affected by daylight savings time. Signed-off-by:
Federico Vaga <federico.vaga@gmail.com> Signed-off-by:
-
Prashant Laddha authored
The intermediate calculation in the expression for hblank can exceed 32 bit signed range. This overflow can lead to negative values for hblank. Typecasting intermediate variable to higher precision. Cc: Martin Bugge <marbugge@cisco.com> Signed-off-by:
Prashant Laddha <prladdha@cisco.com> [hans.verkuil@cisco.com: made the denominator u32, since that's what div_u64 expects] Signed-off-by:
-
Ricardo Ribalda authored
Remove code duplication by merging two cases in a switch. Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
-
Ricardo Ribalda authored
Support for V4L2_PIX_FMT_Y16, a 16 bit greyscale format. Signed-off-by:
-
Antti Palosaari authored
Load rtl2832_sdr driver for devices having fc2580 tuner. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Add initial support for fc2580 tuner based devices. Tuner is controlled via V4L2 subdevice API. Passes v4l2-compliance tests. Signed-off-by:
-
Antti Palosaari authored
Implement V4L2 subdevice for bandwidth and frequency controls of SDR usage. That driver now implements both DVB frontend and V4L2 subdevice. Driver itself is I2C driver. Lets see how it works. Signed-off-by:
-
Antti Palosaari authored
Calculate low-pass filter control word dynamically from given radio channel bandwidth. Signed-off-by:
-
Antti Palosaari authored
rtl2832 demod driver has support for FC2580 tuner config, no need to abuse FC0012 settings anymore. Signed-off-by:
-
Antti Palosaari authored
Add reg/val inittab for FC2580 tuner. Signed-off-by:
-
Antti Palosaari authored
Use div_u64() to simplify and remove home made divides. Signed-off-by:
-
Antti Palosaari authored
Use regmap for I2C register access. Signed-off-by:
-
Antti Palosaari authored
Fix logging. Style issues. Rename things. Signed-off-by:
-
Antti Palosaari authored
We are using I2C client binding now, so remove old media attach. Signed-off-by:
-
Antti Palosaari authored
Change tua9001 driver from media binding to I2C client binding. Signed-off-by:
-
Antti Palosaari authored
Change tua9001 driver from media binding to I2C client binding. Signed-off-by:
-
Antti Palosaari authored
Add I2C bindings. Signed-off-by:
-
Antti Palosaari authored
Driver supports multiple chipset versions. Devices are ordered to ID table per used chipset type. "ITE 9303 Generic" device uses IT9303 chipset and was added mistakenly between IT9135 IDs. Signed-off-by:
-
Antti Palosaari authored
Replace home made register access routines with regmap. Signed-off-by:
-
Antti Palosaari authored
Rename driver state from priv to dev. Remove legacy i2c-gate control. Use I2C client for proper dev_() logging. Signed-off-by:
-
