Only userspace can make an educated decision when
a trigger frame is required so make sure the
autotrigger service is disabled.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

New wmi-tlv firmware for qca6174 has u-UAPSD
autotrigger service. If it is enabled firmware
generates trigger frames automatically as
configured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The workaround couldn't work correctly because the
802.11 header wasn't properly stripped of QoS Data
bit so it wasn't recognized in the later parts of
tx path as NullFunc frame and ended up in HTT Tx
instead of HTT Mgmt Tx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Firmware supporting beacon templates (i.e. wmi-tlv
for qca6174) doesn't implicitly take dtim period
from the template. Instead it requires vdev param
to be set accordingly.

This fixes dtim period being stuck at 3.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

HTT Tx protocol uses arbitrary host assigned ids
too associate with MSDUs when delivering
completions.

Instead of rolling out own id generation scheme
use the tools provided in kernel.

This should have little to no effect on
performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Both 10.2 firmware binaries 10.2-00082-4 and
10.2.4.20 have introduced ABI changes to fw_stats
each. This caused fw_stats to output wrong data.

Define new structures and use them to parse the
statistics correctly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This will make it easier to implement fw stats
parsing for firmware 10.2.

This also renames a few structures for
consistency.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The QCA6174 in combination with new wmi-tlv firmware is capable of
multi-channel, beamforming, tdls and other features.

This patch just makes it possible to boot these devices and do some basic stuff
like connect to an AP without encryption. Some things may not work or may be
unreliable. New features will be implemented later. This will be addressed
eventually with future patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The QCA6174 chip has an extra 4 bytes in
rx_ppdu_end structure which is used in htt_rx_desc
and HTT Rx ring offset setup. This is necessary
for correct Rx for QCA6174 (otherwise Rx
descriptors are overwritten and corrupted).

This means QCA988X will have an extra 4 byte
padding in Rx descriptor layout which is harmless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There are some very rare cases with some hardware
configuration that the device doesn't init quickly
enough in which case reading chip_id yielded 0.
This caused driver to subsequently fail to setup
the device.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

New firmware and firmware (qca6174 hw3.0+ and fw
266+) are capable of full aggregation rx
reordering. If it's enabled then Rx is handled via
a new, separate htt event.

The rx ring behaviour is changed a little to
support the new rx scheme. These changes shouldn't
affect qca988x performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It doesn't make much sense to share the
ath10k_skb_cb with Rx path. The Rx path doesn't
need to keep any mac80211's data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions may report this event as
part of their diagnostics.

This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions may report this event as
part of their diagnostics.

This avoids `unknown event` warnings and adds
tracing for the event.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

To be compliant with the hwmon interface the unit needs to be
millidegree Celsius. Fix that.
Reported-by: Matthias Kaehlcke <mka@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add a comment for indicating that the ATH10K_SCAN_RUNNING case falls
through to the ATH10K_SCAN_ABORTING case in __ath10k_scan_finish.  This
will document that the lack of a break is intentional.

Coverity: CID 1260017
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Originally the explicit fw register dump was added
to wait_for_target_init because interrupts are
masked early during power_up.

Due to some changes in power_up/reset sequences
sometimes when fw crashed ath10k would print the
dump more than once via hif_stop -> warm_reset ->
wait_for_target_init, possibly with different
values each.

Prevent this by doing the explicit fw register
dump only during power_up instead of
wait_for_target_init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The duty cycle (% of quiet duration) is used to put the device
in quiet mode for the given period. Currently the quiet duration
is wrongly calculated which results in not enabling quiet mode.
Fix the calculation as below

     duration = (period * duty cycle) / 100
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

New firmware revisions support beacon and probe
response templates instead. This means SWBA events
are no longer delivered for these firmware
revisions.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Along beacon template host is expected to setup
p2p information elements as well. Implement wmi
interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

New firmware revisions with beacon templates need
probe templates as well because they don't forward
probe requests to host at all.

This is required for new firmware to work with
direct probe requests (notably required by hidden
ssid AP).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

New firmware revisions may support setting beacon
template. Implement wmi interface for it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This event is delivered to host by firmware if it
supports beacon templates only.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Because of wrong macro check in commit 96bba983 ("ath10k: fix build error
when hwmon is off"), hwmon never be enabled. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When replenishing Rx buffers driver updates the address of the
buffer and the index of rx buffer in rx ring to the firmware.
Change in order by CPU can cause rx ring corruption. Add memory
barrier before updating rx buffer index to guarantee the order.

This could fix some instances of rx ring corruption due to done
bit in rx attention flag not set.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

wait_for_completion_timeout does not return negative values so the tests
for <= 0 are not needed and the case differentiation in the error handling
path unnecessary.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Recent commit
30c78167 ("ath10k:
set max_num_vdevs based on wmi op version")
skipped wmi-tlv case and left max_num_vdevs reset.
Make sure it is properly set.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

htt->max_throughput_mbps is not used anywhere.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Return a negative error code on failure.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This per-station debugfs entry helps to send delba in manual mode
for debugging purpose. It accepts tid, initiator and reason code
as inputs.

To send delba,

echo 0 1 37 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	     stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This per-station debugfs entry helps to send addba response in
manual mode for debugging purpose. It accepts tid and status code
as input arguments.

To send addba response,

echo 0 25 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	   stations/XX:XX:XX:XX:XX:XX/addba_resp
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This per-station debugfs entry helps to send addba request in manual
mode. Need to pass two configuration parameters (tid, buffer size)
as input.

To send addba,

echo 1 32 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	   stations/XX:XX:XX:XX:XX:XX/addba
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add per station debugfs files when a station is added to mac80211's
station list. This helps to group peer specific debugfs entries
altogether. Right now this callback adds support to test aggregation
procedures (addba/addba_resp/delba) manually.

To enable automatic aggregation in target,
echo 0 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	stations/XX:XX:XX:XX:XX:XX/aggr_mode

For manual mode,
echo 1 >/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
	stations/XX:XX:XX:XX:XX:XX/aggr_mode
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for sending delba request. This command is used for
debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for sending addba response manually. This command
is used for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for sending addba request. This command is meant
for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add WMI support for clearing addba response before switching aggregation
mode (auto/manual) for debugging purpose.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This feature allows the FW to batch RX indications,
reducing the rate of host interrupt generation, which
in turn reduces CPU load. Currently, this is enabled
only for the 10.2 firmware.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

A value of zero indicates that 128B is the maximum
DMA request size for read/writes. But PCI cards based
on AR9880 can support 256B, so enable this for
the 10.2 firmware.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* Device tree support

* Major restructuring how to handle different WMI interface versions

* Add WMI TLV interface in preparation for new firmware interface support

* Support new firmware branch 10.2.4

* Add thermal cooling interface

* Add hwmon interface to read temparture from the device

And of course lots of small fixes and cleanups.