rndis_check_bssid_list() originally tried to check if bssid->mac and
match_bssid are equal using compare_ether_addr() when it should use
!compare_ether_addr(). This check was added by commit
b5257c95 as part of workaround for
hardware issue.

Commit 2e42e474 that replaced
compare_ether_addr with ether_addr_equal relieved that this compare
to be inverse of what it should be.

Compare was added as response to hardware bug, where bssid-list does
not contain BSSID and other information of currently connected AP
(spec insists that device must provide this information in the list
when connected). Lack bssid-data on current connection then causes
WARN_ON somewhere in cfg80211. Workaround was to check if bssid-list
returns current bssid and if it does not, manually construct bssid
information in other ways. And this workaround worked, with inverse
check. Which must mean that when hardware is experiencing the problem,
it's actually returning empty bssid-list and this check didn't make
any difference for workaround.

However inverse check causes workaround be activated when bssid-list
returns only entry, currently connected BSSID. That does not cause
problems in itself, just slightly more inaccurate information in
scan-list.

Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.

this patch is dependent on 'cfg80211: fix interface combinations'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

this patch is dependent on the patch "cfg80211: fix interface
combinations"

In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC.  we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.

The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.

        ath: phy0: Cannot create ADHOC interface when other
        interfaces already exist.
        WARNING: at net/mac80211/driver-ops.h:12
        ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
        Hardware name: 2842RK1
        wlan2:  Failed check-sdata-in-driver check, flags: 0x0

        Call Trace:
        [<c01361b2>] warn_slowpath_common+0x72/0xa0
        [<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
        [mac80211]
        [<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
        [mac80211]
        [<c0136283>] warn_slowpath_fmt+0x33/0x40
        [<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
        [<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
        [<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
        [<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]

Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

commit 24398e39
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Wed Mar 28 10:58:36 2012 +0200

    mac80211: set HT channel before association

removed IEEE80211_CONF_CHANGE_CHANNEL argument from ieee80211_hw_config,
which is required by iwl4965 driver, otherwise that driver does not
configure channel properly and is not able to associate.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

llcp_sock_getname() might get called before the LLCP socket was created.
This condition isn't checked, and llcp_sock_getname will simply deref a
NULL ptr in that case.

This exists starting with d646960f ("NFC: Initial LLCP support").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This feature has been reported to be buggy and enabled by
default. We therefore need to disable it manually.

Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When we remove a key, we put a key index which was supposed
to tell the fw that we are actually removing the key. But
instead the fw took that index as a valid index and messed
up the SRAM of the device.

This memory corruption on the device mangled the data of
the SCD. The impact on the user is that SCD queue 2 got
stuck after having removed keys.
The message is the log that was printed is:

Queue 2 stuck for 10000ms

This doesn't seem to fix the higher queues that get stuck
from time to time.

Cc: stable@vger.kernel.org [2.6.27+]
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

pc could be null if hosttype != BCMA_HOSTTYPE_PCI.
If we are on a device without a pci core this function is called with
pc = null by b43 and brcmsmac. If the host type is PCI we have a pci
core as well and pc can not be null.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

this patch fixes kernel Oops on "rmmod b43" if firmware was not loaded:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff8104e988>] drain_workqueue+0x25/0x142
PGD 153ac6067 PUD 153b82067 PMD 0
Oops: 0000 [#1] SMP
Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

My patch

   iwlwifi: use correct released ucode version

did not correctly report supported firmware
for the 6035 device. This patch fixes it. The
minimum supported firmware version for 6035
is v6.

Also correct the minimum supported firmware
version for the 6000g2 series of devices.

Cc: stable@kernel.org
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add my new trees to the MAINTAINERS file
for the components that I maintain in the
new trees.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211_hwsim: Set IEEE80211_STAT_ACK flag when userspace indicates that the frame has been acknowledged.

The station fail average is not updated correctly since the
IEEE80211_STAT_ACK flag is not set when using wmediumd with
mac80211_hwsim. Set this flag when wmediumd indicates that the frame
was successfully transmitted (eventually).
Signed-off-by: Qasim Javed <qasimj@gmail.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix:

BUG: sleeping function called from invalid context at kernel/workqueue.c:2547
in_atomic(): 1, irqs_disabled(): 0, pid: 629, name: wpa_supplicant
2 locks held by wpa_supplicant/629:
 #0:  (rtnl_mutex){+.+.+.}, at: [<c08b2b84>] rtnl_lock+0x14/0x20
 #1:  (&trigger->leddev_list_lock){.+.?..}, at: [<c0867f41>] led_trigger_event+0x21/0x80
Pid: 629, comm: wpa_supplicant Not tainted 3.3.0-0.rc3.git5.1.fc17.i686
Call Trace:
 [<c046a9f6>] __might_sleep+0x126/0x1d0
 [<c0457d6c>] wait_on_work+0x2c/0x1d0
 [<c045a09a>] __cancel_work_timer+0x6a/0x120
 [<c045a160>] cancel_delayed_work_sync+0x10/0x20
 [<f7dd3c22>] rtl8187_led_brightness_set+0x82/0xf0 [rtl8187]
 [<c0867f7c>] led_trigger_event+0x5c/0x80
 [<f7ff5e6d>] ieee80211_led_radio+0x1d/0x40 [mac80211]
 [<f7ff3583>] ieee80211_stop_device+0x13/0x230 [mac80211]

Removing _sync is ok, because if led_on work is currently running
it will be finished before led_off work start to perform, since
they are always queued on the same mac80211 local->workqueue.

Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=795176Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The problem was found by Larry Finger:
http://marc.info/?l=linux-wireless&m=133702401700614&w=2

The problem is identical to the one for ipw2200 which is already fixed:
http://marc.info/?l=linux-wireless&m=133457257407196&w=2

[   17.766431] ------------[ cut here ]------------
[   17.766467] WARNING: at net/wireless/core.c:562 wiphy_register+0x34c/0x3c0 [cfg80211]()
[   17.766471] Hardware name: Latitude D600
[   17.766474] Modules linked in: ipw2100(+) libipw pcmcia cfg80211 ppdev parport_pc yenta_socket sr_mod pcmcia_rsrc parport iTCO_wdt cdrom sg rfkill pcmcia_
core lib80211 tg3 video button battery ac iTCO_vendor_support joydev shpchp pcspkr pciehp pci_hotplug autofs4 radeon ttm drm_kms_helper uhci_hcd ehci_hcd rtc
_cmos thermal drm hwmon i2c_algo_bit i2c_core processor usbcore usb_common ata_generic ata_piix ahci libahci libata
[   17.766525] Pid: 474, comm: modprobe Not tainted 3.4.0-rc7-wl+ #6
[   17.766528] Call Trace:
[   17.766541]  [<c066ad08>] ? printk+0x28/0x2a
[   17.766552]  [<c0230edd>] warn_slowpath_common+0x6d/0xa0
[   17.766563]  [<e0b253bc>] ? wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766573]  [<e0b253bc>] ? wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766578]  [<c0230f2d>] warn_slowpath_null+0x1d/0x20
[   17.766588]  [<e0b253bc>] wiphy_register+0x34c/0x3c0 [cfg80211]
[   17.766605]  [<e0b5b0d6>] ipw2100_wdev_init+0x196/0x1c0 [ipw2100]
[   17.766616]  [<e0b5d962>] ipw2100_pci_init_one+0x2b2/0x694 [ipw2100]
[   17.766632]  [<c047ce52>] local_pci_probe+0x42/0xb0
[   17.766637]  [<c047e2b0>] pci_device_probe+0x60/0x90
[   17.766645]  [<c0376de2>] ? sysfs_create_link+0x12/0x20
[   17.766654]  [<c050f1f6>] really_probe+0x56/0x2e0
[   17.766659]  [<c037636d>] ? create_dir+0x5d/0xa0
[   17.766667]  [<c0518c6b>] ? pm_runtime_barrier+0x3b/0xa0
[   17.766672]  [<c050f5e4>] driver_probe_device+0x44/0xa0
[   17.766677]  [<c047e227>] ? pci_match_device+0x97/0xa0
[   17.766681]  [<c050f6c9>] __driver_attach+0x89/0x90
[   17.766686]  [<c050f640>] ? driver_probe_device+0xa0/0xa0
[   17.766691]  [<c050da2a>] bus_for_each_dev+0x3a/0x70
[   17.766695]  [<c050ee6c>] driver_attach+0x1c/0x30
[   17.766699]  [<c050f640>] ? driver_probe_device+0xa0/0xa0
[   17.766704]  [<c050ea77>] bus_add_driver+0x187/0x280
[   17.766710]  [<c045b9cd>] ? kset_find_obj+0x2d/0x60
[   17.766715]  [<c047e2e0>] ? pci_device_probe+0x90/0x90
[   17.766719]  [<c047e2e0>] ? pci_device_probe+0x90/0x90
[   17.766724]  [<c050fb85>] driver_register+0x65/0x110
[   17.766729]  [<c047e09d>] __pci_register_driver+0x3d/0xa0
[   17.766738]  [<e09f705c>] ipw2100_init+0x5c/0x1000 [ipw2100]
[   17.766743]  [<c020110f>] do_one_initcall+0x2f/0x170
[   17.766749]  [<e09f7000>] ? 0xe09f6fff
[   17.766757]  [<c0287ce8>] sys_init_module+0xa8/0x210
[   17.766766]  [<c067a075>] syscall_call+0x7/0xb
[   17.766769] ---[ end trace 559898c6bb0d1c75 ]---
[   17.767093] ipw2100: probe of 0000:02:03.0 failed with error -5

This warning appears only if we apply Ben Hutchings' fix
http://marc.info/?l=linux-wireless&m=132720204412667&w=2
for the bug reported by Cesare Leonardi
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=656813
with cfg80211 warning during device registration
("cfg80211: failed to add phy80211 symlink to netdev!").

We separate device bring up and registration with network stack
to avoid the problem.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.

Cc: stable@kernel.org
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.

Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Linus reported that due to mac80211 failing to register
the device (due to WoWLAN) his machine crashed etc. as
we double-freed the vmalloc() firmware area. His patch
to fix it was very similar to this one but I noticed
that there's another bug in the area: we complete the
completion before starting, so since we're running in
a work struct context stop() could be called while in
the middle of start() which will almost certainly lead
to issues.

Make a modification similar to his to avoid the double-
free but also move the completion to another spot so it
is only done after start() either finished or failed so
that stop() can have a consistent state.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Most probably a typo, the check should have been for BT_SK_DEFER_SETUP
instead of BT_DEFER_SETUP (which right now only represents a socket
option).
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.

Cc: stable@kernel.org
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

sta_info_cleanup locks the sta_list using rcu_read_lock however
the delete operation isn't rcu safe. A race between sta_info_cleanup
timer being called and a STA being removed can occur which leads
to a panic while traversing sta_list. Fix this by switching to the
RCU-safe versions.

Cc: stable@vger.kernel.org
Reported-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MacBook Pro models with BCM4331 wireless have been found to have the ext
PA lines disabled after resuming from S3 without external power attach.
This causes them to be unable to transmit. Add a workaround to ensure
that the ext PA lines are enabled on BCM4331. Also extend all handling
of ext PA line muxing to BCM43431 as is done in the Broadcom SDK.

BugLink: http://bugs.launchpad.net/bugs/925577
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove spinlock as atomic_t can be used instead. Note we use only 16
lower bits, upper bits are changed but we impilcilty cast to u16.

This fix possible deadlock on IBSS mode reproted by lockdep:

=================================
[ INFO: inconsistent lock state ]
3.4.0-wl+ #4 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/u:2/30374 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (&(&intf->seqlock)->rlock){+.?...}, at: [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
{IN-SOFTIRQ-W} state was registered at:
  [<c04978ab>] __lock_acquire+0x47b/0x1050
  [<c0498504>] lock_acquire+0x84/0xf0
  [<c0835733>] _raw_spin_lock+0x33/0x40
  [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
  [<f9979f2a>] rt2x00queue_write_tx_frame+0x1a/0x300 [rt2x00lib]
  [<f997834f>] rt2x00mac_tx+0x7f/0x380 [rt2x00lib]
  [<f98fe363>] __ieee80211_tx+0x1b3/0x300 [mac80211]
  [<f98ffdf5>] ieee80211_tx+0x105/0x130 [mac80211]
  [<f99000dd>] ieee80211_xmit+0xad/0x100 [mac80211]
  [<f9900519>] ieee80211_subif_start_xmit+0x2d9/0x930 [mac80211]
  [<c0782e87>] dev_hard_start_xmit+0x307/0x660
  [<c079bb71>] sch_direct_xmit+0xa1/0x1e0
  [<c0784bb3>] dev_queue_xmit+0x183/0x730
  [<c078c27a>] neigh_resolve_output+0xfa/0x1e0
  [<c07b436a>] ip_finish_output+0x24a/0x460
  [<c07b4897>] ip_output+0xb7/0x100
  [<c07b2d60>] ip_local_out+0x20/0x60
  [<c07e01ff>] igmpv3_sendpack+0x4f/0x60
  [<c07e108f>] igmp_ifc_timer_expire+0x29f/0x330
  [<c04520fc>] run_timer_softirq+0x15c/0x2f0
  [<c0449e3e>] __do_softirq+0xae/0x1e0
irq event stamp: 18380437
hardirqs last  enabled at (18380437): [<c0526027>] __slab_alloc.clone.3+0x67/0x5f0
hardirqs last disabled at (18380436): [<c0525ff3>] __slab_alloc.clone.3+0x33/0x5f0
softirqs last  enabled at (18377616): [<c0449eb3>] __do_softirq+0x123/0x1e0
softirqs last disabled at (18377611): [<c041278d>] do_softirq+0x9d/0xe0

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&intf->seqlock)->rlock);
  <Interrupt>
    lock(&(&intf->seqlock)->rlock);

 *** DEADLOCK ***

4 locks held by kworker/u:2/30374:
 #0:  (wiphy_name(local->hw.wiphy)){++++.+}, at: [<c045cf99>] process_one_work+0x109/0x3f0
 #1:  ((&sdata->work)){+.+.+.}, at: [<c045cf99>] process_one_work+0x109/0x3f0
 #2:  (&ifibss->mtx){+.+.+.}, at: [<f98f005b>] ieee80211_ibss_work+0x1b/0x470 [mac80211]
 #3:  (&intf->beacon_skb_mutex){+.+...}, at: [<f997a644>] rt2x00queue_update_beacon+0x24/0x50 [rt2x00lib]

stack backtrace:
Pid: 30374, comm: kworker/u:2 Not tainted 3.4.0-wl+ #4
Call Trace:
 [<c04962a6>] print_usage_bug+0x1f6/0x220
 [<c0496a12>] mark_lock+0x2c2/0x300
 [<c0495ff0>] ? check_usage_forwards+0xc0/0xc0
 [<c04978ec>] __lock_acquire+0x4bc/0x1050
 [<c0527890>] ? __kmalloc_track_caller+0x1c0/0x1d0
 [<c0777fb6>] ? copy_skb_header+0x26/0x90
 [<c0498504>] lock_acquire+0x84/0xf0
 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
 [<c0835733>] _raw_spin_lock+0x33/0x40
 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
 [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
 [<f997a5cf>] rt2x00queue_update_beacon_locked+0x5f/0xb0 [rt2x00lib]
 [<f997a64d>] rt2x00queue_update_beacon+0x2d/0x50 [rt2x00lib]
 [<f9977e3a>] rt2x00mac_bss_info_changed+0x1ca/0x200 [rt2x00lib]
 [<f9977c70>] ? rt2x00mac_remove_interface+0x70/0x70 [rt2x00lib]
 [<f98e4dd0>] ieee80211_bss_info_change_notify+0xe0/0x1d0 [mac80211]
 [<f98ef7b8>] __ieee80211_sta_join_ibss+0x3b8/0x610 [mac80211]
 [<c0496ab4>] ? mark_held_locks+0x64/0xc0
 [<c0440012>] ? virt_efi_query_capsule_caps+0x12/0x50
 [<f98efb09>] ieee80211_sta_join_ibss+0xf9/0x140 [mac80211]
 [<f98f0456>] ieee80211_ibss_work+0x416/0x470 [mac80211]
 [<c0496d8b>] ? trace_hardirqs_on+0xb/0x10
 [<c077683b>] ? skb_dequeue+0x4b/0x70
 [<f98f207f>] ieee80211_iface_work+0x13f/0x230 [mac80211]
 [<c045cf99>] ? process_one_work+0x109/0x3f0
 [<c045d015>] process_one_work+0x185/0x3f0
 [<c045cf99>] ? process_one_work+0x109/0x3f0
 [<f98f1f40>] ? ieee80211_teardown_sdata+0xa0/0xa0 [mac80211]
 [<c045ed86>] worker_thread+0x116/0x270
 [<c045ec70>] ? manage_workers+0x1e0/0x1e0
 [<c0462f64>] kthread+0x84/0x90
 [<c0462ee0>] ? __init_kthread_worker+0x60/0x60
 [<c083d382>] kernel_thread_helper+0x6/0x10

Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Using | with a constant is always true.
Likely this should have be &.

cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes a lockdep warning:

===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
net/mac80211/agg-rx.c:148 invoked rcu_dereference_check() without protection!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 1
1 lock held by arecord/11226:
 #0:  (&tid_agg_rx->session_timer){+.-...}, at: [<ffffffff81066bb0>] call_timer_fn+0x0/0x360

stack backtrace:
Pid: 11226, comm: arecord Not tainted 3.1.0-kml #16
Call Trace:
 <IRQ>  [<ffffffff81093454>] lockdep_rcu_dereference+0xa4/0xc0
 [<ffffffffa02778c9>] sta_rx_agg_session_timer_expired+0xc9/0x110 [mac80211]
 [<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211]
 [<ffffffff81066c3a>] call_timer_fn+0x8a/0x360
 [<ffffffff81066bb0>] ? init_timer_deferrable_key+0x30/0x30
 [<ffffffff81477bb0>] ? _raw_spin_unlock_irq+0x30/0x70
 [<ffffffff81067049>] run_timer_softirq+0x139/0x310
 [<ffffffff81091d5e>] ? put_lock_stats.isra.25+0xe/0x40
 [<ffffffff810922ac>] ? lock_release_holdtime.part.26+0xdc/0x160
 [<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211]
 [<ffffffff8105cb78>] __do_softirq+0xc8/0x3c0
 [<ffffffff8108f088>] ? tick_dev_program_event+0x48/0x110
 [<ffffffff8108f16f>] ? tick_program_event+0x1f/0x30
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff8147a43c>] call_softirq+0x1c/0x30
 [<ffffffff81004c55>] do_softirq+0xa5/0xe0
 [<ffffffff8105d1ee>] irq_exit+0xae/0xe0
 [<ffffffff8147ac6b>] smp_apic_timer_interrupt+0x6b/0x98
 [<ffffffff81479ab3>] apic_timer_interrupt+0x73/0x80
 <EOI>  [<ffffffff8146aac6>] ? free_debug_processing+0x1a1/0x1d5
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff8146ab2b>] __slab_free+0x31/0x2ca
 [<ffffffff81477c3a>] ? _raw_spin_unlock_irqrestore+0x4a/0x90
 [<ffffffff81253b8f>] ? __debug_check_no_obj_freed+0x15f/0x210
 [<ffffffff81097054>] ? lock_release_nested+0x84/0xc0
 [<ffffffff8113ec55>] ? kmem_cache_free+0x105/0x250
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff81153b15>] ? putname+0x35/0x50
 [<ffffffff8113ed8f>] kmem_cache_free+0x23f/0x250
 [<ffffffff81153b15>] putname+0x35/0x50
 [<ffffffff81146d8d>] do_sys_open+0x16d/0x1d0
 [<ffffffff81146e10>] sys_open+0x20/0x30
 [<ffffffff81478f42>] system_call_fastpath+0x16/0x1b
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When any interface goes down, it could be the one that we
were doing a remain-on-channel with. We therefore need to
cancel the remain-on-channel and flush the related work
structs so they don't run after the interface has been
removed or even destroyed.

It's also possible in this case that an off-channel SKB
was never transmitted, so free it if this is the case.
Note that this can also happen if the driver finishes
the off-channel period without ever starting it.

Cc: stable@kernel.org
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enforcing interface combinations broke uses of hwsim
with multiple virtual interfaces. Advertise that all
combinations are possible to fix this.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As part of hardware reconfig mac80211 tries
to restore the station state to its values
before the hardware reconfig, but it only
goes to the last-state - 1. Fix this
off-by-one error.

Cc: stable@kernel.org [3.4]
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since my commit
  iwlwifi: use valid TX/RX antenna from hw_params
the config values are pure overrides, not the
real values for all hardware. Therefore, the
EEPROM TX power reading code checks the wrong
values, it should check the hw_params values.

Cc: stable@kernel.org [3.4]
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mesh station that joins an MBSS is reachable using mesh portal with 6
address frame by mesh stations from another MBSS if these two different
MBSSes are bridged. However, if the mesh station later moves into the
same MBSS of those mesh stations, it is unreachable by mesh stations
in the MBSS due to the mpp_paths table is not deleted. A quick fix
is to perform mesh_path_lookup, if it is available for the target
destination, mpp_path_lookup is not performed. When the mesh station
moves back to its original MBSS, the mesh_paths will be deleted once
expired. So, it will be reachable using mpp_path_lookup again.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CFG80211_DEV_WARN_ON() at "net/wireless/ibss.c line 63"
is unnecessarily triggered even after successful connection,
when cfg80211_ibss_joined() is called by driver inside
.join_ibss handler.

This patch fixes the problem by changing 'sme_state' in ibss path
and having WARN_ON() check for 'sme_state' similar to infra
association.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

commit 133d40f9
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Wed Mar 28 16:01:19 2012 +0200

    mac80211: do not scan and monitor connection in parallel

add bug, which make possible to start a scan and never finish it, so
make every new scanning request finish with -EBUSY error. This can
happen on code paths where we finish connection monitoring and clear
IEEE80211_STA_*_POLL flags, but do not check if scan was deferred.
This patch fixes those code paths.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pull device-mapper updates from Alasdair G Kergon:
 "Improve multipath's retrying mechanism in some defined circumstances
  and provide a simple reserve/release mechanism for userspace tools to
  access thin provisioning metadata while the pool is in use."

* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
  dm thin: provide userspace access to pool metadata
  dm thin: use slab mempools
  dm mpath: allow ioctls to trigger pg init
  dm mpath: delay retry of bypassed pg
  dm mpath: reduce size of struct multipath

This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_.  This,
read-only snapshot can be accessed by userland, concurrently with the
live target.

Only one metadata snapshot can be held at a time.  The pool's status
line will give the block location for the current msnap.

Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:

    thin_dump -m <msnap root> <metadata dev>

Available here: https://github.com/jthornber/thin-provisioning-tools

Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:

     i) Incremental backups.

     By using metadata snapshots we can work out what blocks have
     changed over time.  Combined with data snapshots we can ensure
     the data doesn't change while we back it up.

     A short proof of concept script can be found here:

     https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb

     ii) Migration of thin devices from one pool to another.

     iii) Merging snapshots back into an external origin.

     iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>

After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device.  Until this has happened, ioctls return -EAGAIN.

With this patch, new paths are made available in response to an ioctl
too.  The processing of the ioctl gets delayed until this has happened.

Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.

Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure.  Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands).  For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too.  It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>