The patch below removes the uses of save_flags/restore_flags/cli
etc. from the macserial driver and replaces them with a spinlock.

This patch updates the CUDA driver (the power/reset/ADB controller on
older powermacs) to fix some SMP issues and to match the 2.4 version
of the driver.

From Ben Herrenschmidt.

This patch updates include/linux/adb.h and include/linux/pmu.h with
some additional definitions that we need on powermacs and powerbooks.

into home.transmeta.com:/home/torvalds/v2.5/linux

into samba.org:/home/paulus/kernel/for-linus-ppc

into samba.org:/home/paulus/kernel/for-linus-ppc

Convert the pcnet_cs driver to use the new registration call.

Remove the linked list of pcmcia_drivers. It didn't even handle removal of a
driver properly, so it won't be missed all that much.

Register all pcmcia drivers with the pcmcia bus within the old
register_pccard_driver() function. Alternatively, a new
registration function "pcmcia_register_driver()" (and its
counterpart,  "pcmcia_unregister_driver()") can be used.

Register a bus_type pcmcia_bus_type. This means the initialization of
the ds module needs to be done in two levels: one quite early
(subsys_initcall) so that drivers may use the bus_type; the other one
must stay that late (late_initcall). As only one initcall can be
specified within one module, some tweaking is needed.

into penguin.transmeta.com:/home/penguin/torvalds/repositories/kernel/linux

Since it gets 1 device right it wasnt hard to fix 8)

I'm looking into the other IDE problem from the merge - several people
see hangs. Bartolomiej has found one suspicious looking candidate. I'll
try and pin it down ASAP.

- Redo the timing stuff using jiffies properly
- Clean up the exit paths
- Make the ioctl use a semaphore
- Fix broken locking on the AEN list

Two problems with the original change

1. We should return bytes actually processed on an error according to
SuS/POSIX. Technically the EFAULT path is outside the spec but its best
we follow

2. We need to fix most of this anyway because the final section of the
change was wrong. If retval was set we retried and got an efault again
in some cases

I think this way of doing it is right but it could do with further
review

into home.transmeta.com:/home/torvalds/v2.5/linux

* Increase default Rx descriptors from 80 to 256 to give
  better Rx buffering capability in the case of heavy
  Rx load with small packets.

into home.transmeta.com:/home/torvalds/v2.5/linux

Fix incorrect PCI cache line size assumptions on i386 and thus
avoid potential memory corruption with Memory Write-and-Invalidate.

Comments from rmk:

Make setup-bus.c properly aware of cardbus bridges.  We treat the
bus behind a cardbus bridge more or less like any other bus, except
we don't explicitly descend below.  We do, however, explicitly
reserve IO and memory space as we have done in the past.  Memory
space is doubed to 32MB as a measure to allow the Mobility
cardbus-pci stuff to work.  The amount of space reserved is now
specified by a couple of #defines at the top of the file.

This allows pci_bus_assign_resources() and pci_bus_size_bridges()
to be called for both root buses as well as cardbus secondary buses.

Comments from Ivan follows:

This patch combines your(rmk) cardbus changes (formerly pci-11)
and my "arbitrary resource layout" stuff. This + current bk works
on nautilus.

Most interesting feature: this can be used on partially
allocated PCI tree. For instance, i386 PCI code has always been
absolutely helpless wrt incorrectly initialized p2p bridges.
Now it can just call pci_assign_unassigned_resources() in the
end of PCI init and it would fix following problems:
- completely uninitialized bridge windows (with base and limit 0);
- erroneously "closed" windows;
- windows overlapping with something else.

  
Minor cleanup: don't call pci_update_resource() for bridges,
get rid of bogus "trying to set non-standard region" messages thus.