- 02 Oct, 2012 40 commits
-
-
Manoj Iyer authored
commit 29d21457 upstream. On Intel Panther Point chipset USB 3.0 devices show up as high-speed devices on powerup, but after an s3 cycle they are correctly recognized as SuperSpeed. At powerup switch the port to xHCI so that USB 3.0 devices are correctly recognized. BugLink: http://bugs.launchpad.net/bugs/1000424 This patch should be backported to kernels as old as 3.0, that contain commit ID 69e848c2 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by:
Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Matthew Garrett authored
commit e955a1cd upstream. My test platform (Intel DX79SI) boots reliably under BIOS, but frequently crashes when booting via UEFI. I finally tracked this down to the xhci handoff code. It seems that reads from the device occasionally just return 0xff, resulting in xhci_find_next_cap_offset generating a value that's larger than the resource region. We then oops when attempting to read the value. Sanity checking that value lets us avoid the crash. I've no idea what's causing the underlying problem, and xhci still doesn't actually *work* even with this, but the machine at least boots which will probably make further debugging easier. This should be backported to kernels as old as 2.6.31, that contain the commit 66d4eadd "USB: xhci: BIOS handoff and HW initialization." Signed-off-by:
Matthew Garrett <mjg@redhat.com> Signed-off-by:
-
Dan Carpenter authored
commit 052c7f9f upstream. The intent was to test whether the flag was set. This patch should be backported to stable kernels as old as 3.0, since it fixes a bug in commit e95829f4 "xhci: Switch PPT ports to EHCI on shutdown.", which was marked for stable. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Keng-Yu Lin authored
commit a96874a2 upstream. With a previous patch to enable the EHCI/XHCI port switching, it switches all the available ports. The assumption is not correct because the BIOS may expect some ports not switchable by the OS. There are two more registers that contains the information of the switchable and non-switchable ports. This patch adds the checking code for the two register so that only the switchable ports are altered. This patch should be backported to kernels as old as 3.0, that contain commit ID 69e848c2 "Intel xhci: Support EHCI/xHCI port switching." Signed-off-by:
Keng-Yu Lin <kengyu@canonical.com> Signed-off-by:
-
Alan Stern authored
commit 92fc7a8b upstream. This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss infrared touchboard device. The device doesn't like to be asked for its interface strings. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
adam ? <adam3337@wp.pl> Signed-off-by:
-
Éric Piel authored
commit dafc4f7b upstream. Commit b69cc672 added support for the E-861. After acquiring a C-867, I realised that every Physik Instrumente's device has a different PID. They are listed in the Windows device driver's .inf file. So here are all PIDs for the current (and probably future) USB devices from Physik Instrumente. Compiled, but only actually tested on the E-861 and C-867. Signed-off-by:
Éric Piel <piel@delmic.com> Signed-off-by:
-
Bjørn Mork authored
commit f08dea73 upstream. The Microchip vid:pid 04d8:000a is used for their CDC ACM demo firmware application. This is a device with a single function conforming to the CDC ACM specification and with the intention of demonstrating CDC ACM class firmware and driver interaction. The demo is used on a number of development boards, and may also be used unmodified by vendors using Microchip hardware. Some vendors have re-used this vid:pid for other types of firmware, emulating FTDI chips. Attempting to continue to support such devices without breaking class based applications that by matching on interface class/subclass/proto being ff/ff/00. I have no information about the actual device or interface descriptors, but this will at least make the proper CDC ACM devices work again. Anyone having details of the offending device's descriptors should update this entry with the details. Reported-by:
Florian Wöhrl <fw@woehrl.biz> Reported-by:
Xiaofan Chen <xiaofanc@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Bruno Thomsen <bruno.thomsen@gmail.com> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Horst Schirmeier authored
commit 26a538b9 upstream. This adds the USB PID for the NZR SEM 16+ USB energy monitor device <http://www.nzr.de>. It works perfectly with the GPL software on <http://schou.dk/linux/sparometer/>. Signed-off-by:
Horst Schirmeier <horst@schirmeier.com> Signed-off-by:
-
Pavankumar Kondeti authored
commit 3d037774 upstream. There is a possibility of QH overlay region having reference to a stale qTD pointer during unlink. Consider an endpoint having two pending qTD before unlink process begins. The endpoint's QH queue looks like this. qTD1 --> qTD2 --> Dummy To unlink qTD2, QH is removed from asynchronous list and Asynchronous Advance Doorbell is programmed. The qTD1's next qTD pointer is set to qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell interrupt. If QH's current qTD pointer points to qTD1, transfer overlay region still have reference to qTD2. But qtD2 is just unlinked and freed. This may cause EHCI system error. Fix this by updating qTD next pointer in QH overlay region with the qTD next pointer of the current qTD. Signed-off-by:
Pavankumar Kondeti <pkondeti@codeaurora.org> Acked-by:
-
Weston Andros Adamson authored
commit 01913b49 upstream. If decode_getfh failed, nfs4_xdr_dec_open would return 0 since the last decode_* call must have succeeded. Signed-off-by:
Weston Andros Adamson <dros@netapp.com> Signed-off-by:
Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by:
-
Trond Myklebust authored
commit 872ece86 upstream. Apparently, am-utils is still using the legacy binary mountdata interface, and is having trouble parsing /proc/mounts due to the 'port=' field being incorrectly set. The following patch should fix up the regression. Reported-by:
Marius Tolzmann <tolzmann@molgen.mpg.de> Signed-off-by:
-
Trond Myklebust authored
commit c3f52af3 upstream. When the NFS_COOKIEVERF helper macro was converted into a static inline function in commit 99fadcd7 (nfs: convert NFS_*(inode) helpers to static inline), we broke the initialisation of the readdir cookies, since that depended on doing a memset with an argument of 'sizeof(NFS_COOKIEVERF(inode))' which therefore changed from sizeof(be32 cookieverf[2]) to sizeof(be32 *). At this point, NFS_COOKIEVERF seems to be more of an obfuscation than a helper, so the best thing would be to just get rid of it. Also see: https://bugzilla.kernel.org/show_bug.cgi?id=46881Reported-by:
Andi Kleen <andi@firstfloor.org> Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
-
Gertjan van Wingerde authored
commit a396e100 upstream. We need to program the rfkill switch GPIO pin direction to input at device initialization time, not only when the interface is brought up. Doing this only when the interface is brought up could lead to rfkill detecting the switch is turned on erroneously and inability to create the interface and bringing it up. Reported-and-tested-by:
Andreas Messer <andi@bastelmap.de> Signed-off-by:
Gertjan van Wingerde <gwingerde@gmail.com> Acked-by:
Ivo Van Doorn <ivdoorn@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Gertjan van Wingerde authored
commit 6ced58a5 upstream. The register is 16 bits wide, not 32. Signed-off-by:
-
Nicolas Ferre authored
commit c4567976 upstream. Avoid the construction of a malformed DMA request sent to the DMA controller. Log message is for debug only because this condition is unlikely to append and may only trigger at driver development time. Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Vinod Koul <vinod.koul@linux.intel.com> Signed-off-by:
-
Nicolas Ferre authored
commit c618a9be upstream. s/dma_memcpy/slave_sg/ and it is sg length that we are talking about. Signed-off-by:
-
Luis R. Rodriguez authored
commit a85d0d7f upstream. When call_crda() is called we kick off a witch hunt search for the same regulatory domain on our internal regulatory database and that work gets kicked off on a workqueue, this is done while the cfg80211_mutex is held. If that workqueue kicks off it will first lock reg_regdb_search_mutex and later cfg80211_mutex but to ensure two CPUs will not contend against cfg80211_mutex the right thing to do is to have the reg_regdb_search() wait until the cfg80211_mutex is let go. The lockdep report is pasted below. cfg80211: Calling CRDA to update world regulatory domain ====================================================== [ INFO: possible circular locking dependency detected ] 3.3.8 #3 Tainted: G O ------------------------------------------------------- kworker/0:1/235 is trying to acquire lock: (cfg80211_mutex){+.+...}, at: [<816468a4>] set_regdom+0x78c/0x808 [cfg80211] but task is already holding lock: (reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (reg_regdb_search_mutex){+.+...}: [<800a8384>] lock_acquire+0x60/0x88 [<802950a8>] mutex_lock_nested+0x54/0x31c [<81645778>] is_world_regdom+0x9f8/0xc74 [cfg80211] -> #1 (reg_mutex#2){+.+...}: [<800a8384>] lock_acquire+0x60/0x88 [<802950a8>] mutex_lock_nested+0x54/0x31c [<8164539c>] is_world_regdom+0x61c/0xc74 [cfg80211] -> #0 (cfg80211_mutex){+.+...}: [<800a77b8>] __lock_acquire+0x10d4/0x17bc [<800a8384>] lock_acquire+0x60/0x88 [<802950a8>] mutex_lock_nested+0x54/0x31c [<816468a4>] set_regdom+0x78c/0x808 [cfg80211] other info that might help us debug this: Chain exists of: cfg80211_mutex --> reg_mutex#2 --> reg_regdb_search_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(reg_regdb_search_mutex); lock(reg_mutex#2); lock(reg_regdb_search_mutex); lock(cfg80211_mutex); *** DEADLOCK *** 3 locks held by kworker/0:1/235: #0: (events){.+.+..}, at: [<80089a00>] process_one_work+0x230/0x460 #1: (reg_regdb_work){+.+...}, at: [<80089a00>] process_one_work+0x230/0x460 #2: (reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211] stack backtrace: Call Trace: [<80290fd4>] dump_stack+0x8/0x34 [<80291bc4>] print_circular_bug+0x2ac/0x2d8 [<800a77b8>] __lock_acquire+0x10d4/0x17bc [<800a8384>] lock_acquire+0x60/0x88 [<802950a8>] mutex_lock_nested+0x54/0x31c [<816468a4>] set_regdom+0x78c/0x808 [cfg80211] Reported-by:
Felix Fietkau <nbd@openwrt.org> Tested-by:
Luis R. Rodriguez <mcgrof@do-not-panic.com> Reviewed-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Ira W. Snyder authored
commit e21093ef upstream. The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for the reset registers. To support older hardware, the code is changed to use the hardware reset register on the Janz VMOD-ICAN3 hardware itself. Signed-off-by:
Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Marc Kleine-Budde authored
commit ab04c8bd upstream. This patch fixes an oops which occurs when unloading the driver, while the network interface is still up. The problem is that first the io mapping is teared own, then the CAN device is unregistered, resulting in accessing the hardware's iomem: [ 172.744232] Unable to handle kernel paging request at virtual address c88b0040 [ 172.752441] pgd = c7be4000 [ 172.755645] [c88b0040] *pgd=87821811, *pte=00000000, *ppte=00000000 [ 172.762207] Internal error: Oops: 807 [#1] PREEMPT ARM [ 172.767517] Modules linked in: ti_hecc(-) can_dev [ 172.772430] CPU: 0 Not tainted (3.5.0alpha-00037-g3554cc0 #126) [ 172.778961] PC is at ti_hecc_close+0xb0/0x100 [ti_hecc] [ 172.784423] LR is at __dev_close_many+0x90/0xc0 [ 172.789123] pc : [<bf00c768>] lr : [<c033be58>] psr: 60000013 [ 172.789123] sp : c5c1de68 ip : 00040081 fp : 00000000 [ 172.801025] r10: 00000001 r9 : c5c1c000 r8 : 00100100 [ 172.806457] r7 : c5d0a48c r6 : c5d0a400 r5 : 00000000 r4 : c5d0a000 [ 172.813232] r3 : c88b0000 r2 : 00000001 r1 : c5d0a000 r0 : c5d0a000 [ 172.820037] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 172.827423] Control: 10c5387d Table: 87be4019 DAC: 00000015 [ 172.833404] Process rmmod (pid: 600, stack limit = 0xc5c1c2f0) [ 172.839447] Stack: (0xc5c1de68 to 0xc5c1e000) [ 172.843994] de60: bf00c6b8 c5c1dec8 c5d0a000 c5d0a000 00200200 c033be58 [ 172.852478] de80: c5c1de44 c5c1dec8 c5c1dec8 c033bf2c c5c1de90 c5c1de90 c5d0a084 c5c1de44 [ 172.860992] dea0: c5c1dec8 c033c098 c061d3dc c5d0a000 00000000 c05edf28 c05edb34 c000d724 [ 172.869476] dec0: 00000000 c033c2f8 c5d0a084 c5d0a084 00000000 c033c370 00000000 c5d0a000 [ 172.877990] dee0: c05edb00 c033c3b8 c5d0a000 bf00d3ac c05edb00 bf00d7c8 bf00d7c8 c02842dc [ 172.886474] df00: c02842c8 c0282f90 c5c1c000 c05edb00 bf00d7c8 c0283668 bf00d7c8 00000000 [ 172.894989] df20: c0611f98 befe2f80 c000d724 c0282d10 bf00d804 00000000 00000013 c0068a8c [ 172.903472] df40: c5c538e8 685f6974 00636365 c61571a8 c5cb9980 c61571a8 c6158a20 c00c9bc4 [ 172.911987] df60: 00000000 00000000 c5cb9980 00000000 c5cb9980 00000000 c7823680 00000006 [ 172.920471] df80: bf00d804 00000880 c5c1df8c 00000000 000d4267 befe2f80 00000001 b6d90068 [ 172.928985] dfa0: 00000081 c000d5a0 befe2f80 00000001 befe2f80 00000880 b6d90008 00000008 [ 172.937469] dfc0: befe2f80 00000001 b6d90068 00000081 00000001 00000000 befe2eac 00000000 [ 172.945983] dfe0: 00000000 befe2b18 00023ba4 b6e6addc 60000010 befe2f80 a8e00190 86d2d344 [ 172.954498] [<bf00c768>] (ti_hecc_close+0xb0/0x100 [ti_hecc]) from [<c033be58>] (__dev__registered_many+0xc0/0x2a0) [ 172.984161] [<c033c098>] (rollback_registered_many+0xc0/0x2a0) from [<c033c2f8>] (rollback_registered+0x20/0x30) [ 172.994750] [<c033c2f8>] (rollback_registered+0x20/0x30) from [<c033c370>] (unregister_netdevice_queue+0x68/0x98) [ 173.005401] [<c033c370>] (unregister_netdevice_queue+0x68/0x98) from [<c033c3b8>] (unregister_netdev+0x18/0x20) [ 173.015899] [<c033c3b8>] (unregister_netdev+0x18/0x20) from [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc]) [ 173.026245] [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc]) from [<c02842dc>] (platform_drv_remove+0x14/0x18) [ 173.036712] [<c02842dc>] (platform_drv_remove+0x14/0x18) from [<c0282f90>] (__device_release_driver+0x7c/0xbc) Tested-by:
Jan Luebbe <jlu@pengutronix.de> Cc: Anant Gole <anantgole@ti.com> Signed-off-by:
-
Søren Holm authored
commit ed3770a9 upstream. Signed-off-by:
Søren Holm <sgh@sgh.dk> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Anisse Astier authored
commit 8669cf67 upstream. On Toshiba Satellite C850D, the touchpad and the keyboard might randomly not work at boot. Preventing MUX mode activation solves this issue. Signed-off-by:
Anisse Astier <anisse@astier.eu> Signed-off-by:
Dmitry Torokhov <dtor@mail.ru> Signed-off-by:
-
Wen Congyang authored
commit 85f2a2ef upstream. When allocating memory fails, page is NULL. page_to_pfn() will cause the kernel panicked if we don't use sparsemem vmemmap. Link: http://lkml.kernel.org/r/505AB1FF.8020104@cn.fujitsu.comAcked-by:
Mel Gorman <mel@csn.ul.ie> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Reviewed-by:
Minchan Kim <minchan@kernel.org> Signed-off-by:
Wen Congyang <wency@cn.fujitsu.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Matthew Leach authored
commit e1e5b7e4 upstream. This patch zeroes the SCTLR.TRE bit prior to setting the mapping as cacheable for ARMv7 cores in the decompressor, ensuring that the memory region attributes are obtained from the C and B bits, not from the page tables. Cc: Nicolas Pitre <nico@fluxnic.net> Reviewed-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Matthew Leach <matthew.leach@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Tetsuyuki Kobayashi authored
No upstream commit as this is a merge error in the 3.0 tree. ARM_ERRATA_764369 and PL310_ERRATA_769419 do not appear in config menu in stable 3.0.y tree. This is because backported patch for arm/arm/Kconfig applied wrong place. This patch solves it. Signed-off-by:
Tetsuyuki Kobayashi <koba@kmckk.co.jp> Signed-off-by:
-
Toshi Kani authored
commit 308b135e upstream. kdump can be interrupted by watchdog timer when the timer is left activated on the crash kernel. Changed the hpwdt driver to disable watchdog timer at boot-time. This assures that watchdog timer is disabled until /dev/watchdog is opened, and prevents watchdog timer to be left running on the crash kernel. Signed-off-by:
Toshi Kani <toshi.kani@hp.com> Tested-by:
Lisa Mitchell <lisa.mitchell@hp.com> Signed-off-by:
Thomas Mingarelli <Thomas.Mingarelli@hp.com> Signed-off-by:
Wim Van Sebroeck <wim@iguana.be> Signed-off-by:
-
Stephen M. Cameron authored
commit 256d0eaa upstream. If a command status of CMD_PROTOCOL_ERR is received, this information should be conveyed to the SCSI mid layer, not dropped on the floor. CMD_PROTOCOL_ERR may be received from the Smart Array for any commands destined for an external RAID controller such as a P2000, or commands destined for tape drives or CD/DVD-ROM drives, if for instance a cable is disconnected. This mostly affects multipath configurations, as disconnecting a cable on a non-multipath configuration is not going to do anything good regardless of whether CMD_PROTOCOL_ERR is handled correctly or not. Not handling CMD_PROTOCOL_ERR correctly in a multipath configaration involving external RAID controllers may cause data corruption, so this is quite a serious bug. This bug should not normally cause a problem for direct attached disk storage. Signed-off-by:
Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Eddie Wai authored
commit d6532207 upstream. This patch fixes the following kernel panic invoked by uninitialized fields in the chip initialization for the 1G bnx2 iSCSI offload. One of the bits in the chip initialization is being used by the latest firmware to control overflow packets. When this control bit gets enabled erroneously, it would ultimately result in a bad packet placement which would cause the bnx2 driver to dereference a NULL ptr in the placement handler. This can happen under certain stress I/O environment under the Linux iSCSI offload operation. This change only affects Broadcom's 5709 chipset. Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP: [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5 Pid: 0, comm: swapper Tainted: G ---- 2.6.18-333.el5debug #2 RIP: 0010:[<ffffffff881f0e7d>] [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5 RSP: 0018:ffff8101b575bd50 EFLAGS: 00010216 RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000 RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220 RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000 R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010 R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558 FS: 0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0 Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820) Stack: 000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520 ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20 0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8 Call Trace: <IRQ> [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b [<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231 [<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1 [<ffffffff800125a0>] __do_softirq+0x89/0x133 [<ffffffff8005e30c>] call_softirq+0x1c/0x28 [<ffffffff8006d5de>] do_softirq+0x2c/0x7d [<ffffffff8006d46e>] do_IRQ+0xee/0xf7 [<ffffffff8005d625>] ret_from_intr+0x0/0xa <EOI> [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341 [<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341 [<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341 [<ffffffff80049560>] cpu_idle+0x95/0xb8 [<ffffffff80078b1c>] start_secondary+0x479/0x488 Signed-off-by:
Eddie Wai <eddie.wai@broadcom.com> Reviewed-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
sreekanth.reddy@lsi.com authored
commit 10cce6d8 upstream. This patch checks whether HBA is SAS2008 B0 controller. if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX, as SAS2008 B0 controller doesn't support MSIX interrupts. [jejb: fix whitespace problems] Signed-off-by:
Sreekanth Reddy <sreekanth.reddy@lsi.com> Signed-off-by:
-
Guenter Roeck authored
commit 4e21f4ea upstream. The 'name' sysfs attribute is mandatory for hwmon devices, but was missing in this driver. Cc: Paul Thomas <pthomas8589@gmail.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Jean Delvare <khali@linux-fr.org> Acked-by:
Paul Thomas <pthomas8589@gmail.com> Signed-off-by:
-
Andreas Herrmann authored
commit 5f0ecb90 upstream. The quirk introduced with commit 00250ec9 (hwmon: fam15h_power: fix bogus values with current BIOSes) is not only required during driver load but also when system resumes from suspend. The BIOS might set the previously recommended (but unsuitable) initilization value for the running average range register during resume. Signed-off-by:
Andreas Herrmann <andreas.herrmann3@amd.com> Tested-by:
Andreas Hartmann <andihartmann@01019freenet.de> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 8d54db79 upstream. The hypervisor is in charge of allocating the proper "NUMA" memory and dealing with the CPU scheduler to keep them bound to the proper NUMA node. The PV guests (and PVHVM) have no inkling of where they run and do not need to know that right now. In the future we will need to inject NUMA configuration data (if a guest spans two or more NUMA nodes) so that the kernel can make the right choices. But those patches are not yet present. In the meantime, disable the NUMA capability in the PV guest, which also fixes a bootup issue. Andre says: "we see Dom0 crashes due to the kernel detecting the NUMA topology not by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA). This will detect the actual NUMA config of the physical machine, but will crash about the mismatch with Dom0's virtual memory. Variation of the theme: Dom0 sees what it's not supposed to see. This happens with the said config option enabled and on a machine where this scanning is still enabled (K8 and Fam10h, not Bulldozer class) We have this dump then: NUMA: Warning: node ids are out of bound, from=-1 to=-1 distance=10 Scanning NUMA topology in Northbridge 24 Number of physical nodes 4 Node 0 MemBase 0000000000000000 Limit 0000000040000000 Node 1 MemBase 0000000040000000 Limit 0000000138000000 Node 2 MemBase 0000000138000000 Limit 00000001f8000000 Node 3 MemBase 00000001f8000000 Limit 0000000238000000 Initmem setup node 0 0000000000000000-0000000040000000 NODE_DATA [000000003ffd9000 - 000000003fffffff] Initmem setup node 1 0000000040000000-0000000138000000 NODE_DATA [0000000137fd9000 - 0000000137ffffff] Initmem setup node 2 0000000138000000-00000001f8000000 NODE_DATA [00000001f095e000 - 00000001f0984fff] Initmem setup node 3 00000001f8000000-0000000238000000 Cannot find 159744 bytes in node 3 BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96 Pid: 0, comm: swapper Not tainted 3.3.6 #1 AMD Dinar/Dinar RIP: e030:[<ffffffff81d220e6>] [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96 .. snip.. [<ffffffff81d23024>] sparse_early_usemaps_alloc_node+0x64/0x178 [<ffffffff81d23348>] sparse_init+0xe4/0x25a [<ffffffff81d16840>] paging_init+0x13/0x22 [<ffffffff81d07fbb>] setup_arch+0x9c6/0xa9b [<ffffffff81683954>] ? printk+0x3c/0x3e [<ffffffff81d01a38>] start_kernel+0xe5/0x468 [<ffffffff81d012cf>] x86_64_start_reservations+0xba/0xc1 [<ffffffff81007153>] ? xen_setup_runstate_info+0x2c/0x36 [<ffffffff81d050ee>] xen_start_kernel+0x565/0x56c " so we just disable NUMA scanning by setting numa_off=1. Reported-and-Tested-by:
Andre Przywara <andre.przywara@amd.com> Acked-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
qiuxishi authored
commit f14851af upstream. There may be a bug when registering section info. For example, on my Itanium platform, the pfn range of node0 includes the other nodes, so other nodes' section info will be double registered, and memmap's page count will equal to 3. node0: start_pfn=0x100, spanned_pfn=0x20fb00, present_pfn=0x7f8a3, => 0x000100-0x20fc00 node1: start_pfn=0x80000, spanned_pfn=0x80000, present_pfn=0x80000, => 0x080000-0x100000 node2: start_pfn=0x100000, spanned_pfn=0x80000, present_pfn=0x80000, => 0x100000-0x180000 node3: start_pfn=0x180000, spanned_pfn=0x80000, present_pfn=0x80000, => 0x180000-0x200000 free_all_bootmem_node() register_page_bootmem_info_node() register_page_bootmem_info_section() When hot remove memory, we can't free the memmap's page because page_count() is 2 after put_page_bootmem(). sparse_remove_one_section() free_section_usemap() free_map_bootmem() put_page_bootmem() [akpm@linux-foundation.org: add code comment] Signed-off-by:
Xishi Qiu <qiuxishi@huawei.com> Signed-off-by:
Jiang Liu <jiang.liu@huawei.com> Acked-by:
Mel Gorman <mgorman@suse.de> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jianguo Wu authored
commit 05cf9639 upstream. I found following definition in include/linux/memory.h, in my IA64 platform, SECTION_SIZE_BITS is equal to 32, and MIN_MEMORY_BLOCK_SIZE will be 0. #define MIN_MEMORY_BLOCK_SIZE (1 << SECTION_SIZE_BITS) Because MIN_MEMORY_BLOCK_SIZE is int type and length of 32bits, so MIN_MEMORY_BLOCK_SIZE(1 << 32) will will equal to 0. Actually when SECTION_SIZE_BITS >= 31, MIN_MEMORY_BLOCK_SIZE will be wrong. This will cause wrong system memory infomation in sysfs. I think it should be: #define MIN_MEMORY_BLOCK_SIZE (1UL << SECTION_SIZE_BITS) And "echo offline > memory0/state" will cause following call trace: kernel BUG at mm/memory_hotplug.c:885! sh[6455]: bugcheck! 0 [1] Pid: 6455, CPU 0, comm: sh psr : 0000101008526030 ifs : 8000000000000fa4 ip : [<a0000001008c40f0>] Not tainted (3.6.0-rc1) ip is at offline_pages+0x210/0xee0 Call Trace: show_stack+0x80/0xa0 show_regs+0x640/0x920 die+0x190/0x2c0 die_if_kernel+0x50/0x80 ia64_bad_break+0x3d0/0x6e0 ia64_native_leave_kernel+0x0/0x270 offline_pages+0x210/0xee0 alloc_pages_current+0x180/0x2a0 Signed-off-by:
Jianguo Wu <wujianguo@huawei.com> Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
-
Benoît Locher authored
commit cab32f39 upstream. The MCP2515 has a silicon bug causing repeated frame transmission, see section 5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007). Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually cause the bug. The workaround proposed by Microchip is to use mode 00 and send a RTS command on the SPI bus to initiate the transmission. Signed-off-by:
Benoît Locher <Benoit.Locher@skf.com> Signed-off-by:
-
Guenter Roeck authored
commit 73d7c119 upstream. twl4030_madc_conversion uses do_avg and type structure elements of twl4030_madc_request. Initialize structure to avoid random operation. Fix for: Coverity CID 200794 Uninitialized scalar variable. Cc: Keerthy <j-keerthy@ti.com> Signed-off-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
-
Kevin Hilman authored
commit 8dcebaa9 upstream. On some platforms, bootloaders are known to do some interesting RTC programming. Without going into the obscurities as to why this may be the case, suffice it to say the the driver should not make any assumptions about the state of the RTC when the driver loads. In particular, the driver probe should be sure that all interrupts are disabled until otherwise programmed. This was discovered when finding bursty I2C traffic every second on Overo platforms. This I2C overhead was keeping the SoC from hitting deep power states. The cause was found to be the RTC firing every second on the I2C-connected TWL PMIC. Special thanks to Felipe Balbi for suggesting to look for a rogue driver as the source of the I2C traffic rather than the I2C driver itself. Special thanks to Steve Sakoman for helping track down the source of the continuous RTC interrups on the Overo boards. Signed-off-by:
Kevin Hilman <khilman@ti.com> Cc: Felipe Balbi <balbi@ti.com> Tested-by:
Steve Sakoman <steve@sakoman.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Tested-by:
Shubhrajyoti Datta <omaplinuxkernel@gmail.com> Signed-off-by:
-
Li Haifeng authored
commit 0ba8f2d5 upstream. The heuristic method for buddy has been introduced since commit 43506fad ("mm/page_alloc.c: simplify calculation of combined index of adjacent buddy lists"). But the page address of higher page's buddy was wrongly calculated, which will lead page_is_buddy to fail for ever. IOW, the heuristic method would be disabled with the wrong page address of higher page's buddy. Calculating the page address of higher page's buddy should be based higher_page with the offset between index of higher page and index of higher page's buddy. Signed-off-by:
Haifeng Li <omycle@gmail.com> Signed-off-by:
Gavin Shan <shangw@linux.vnet.ibm.com> Reviewed-by:
-
NeilBrown authored
commit 667a5313 upstream. commit 27a7b260 md: Fix handling for devices from 2TB to 4TB in 0.90 metadata. changed 0.90 metadata handling to truncated size to 4TB as that is all that 0.90 can record. However for RAID0 and Linear, 0.90 doesn't need to record the size, so this truncation is not needed and causes working arrays to become too small. So avoid the truncation for RAID0 and Linear This bug was introduced in 3.1 and is suitable for any stable kernels from then onwards. As the offending commit was tagged for 'stable', any stable kernel that it was applied to should also get this patch. That includes at least 2.6.32, 2.6.33 and 3.0. (Thanks to Ben Hutchings for providing that list). Signed-off-by:
Neil Brown <neilb@suse.de> Signed-off-by:
-
Mel Gorman authored
commit 67a806d9 upstream. The following build error occurred during an alpha build: net/core/sock.c:274:36: error: initializer element is not constant Dave Anglin says: > Here is the line in sock.i: > > struct static_key memalloc_socks = ((struct static_key) { .enabled = > ((atomic_t) { (0) }) }); The above line contains two compound literals. It also uses a designated initializer to initialize the field enabled. A compound literal is not a constant expression. The location of the above statement isn't fully clear, but if a compound literal occurs outside the body of a function, the initializer list must consist of constant expressions. Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
Michael Cree <mcree@orcon.net.nz> Acked-by:
Matt Turner <mattst88@gmail.com> Signed-off-by:
-
Bjørn Mork authored
commit 60e233a5 upstream. Fengguang Wu <fengguang.wu@intel.com> writes: > After the __devinit* removal series, I can still get kernel panic in > show_uevent(). So there are more sources of bug.. > > Debug patch: > > @@ -343,8 +343,11 @@ static ssize_t show_uevent(struct device > goto out; > > /* copy keys to file */ > - for (i = 0; i < env->envp_idx; i++) > + dev_err(dev, "uevent %d env[%d]: %s/.../%s\n", env->buflen, env->envp_idx, top_kobj->name, dev->kobj.name); > + for (i = 0; i < env->envp_idx; i++) { > + printk(KERN_ERR "uevent %d env[%d]: %s\n", (int)count, i, env->envp[i]); > count += sprintf(&buf[count], "%s\n", env->envp[i]); > + } > > Oops message, the env[] is again not properly initilized: > > [ 44.068623] input input0: uevent 61 env[805306368]: input0/.../input0 > [ 44.069552] uevent 0 env[0]: (null) This is a completely different CONFIG_HOTPLUG problem, only demonstrating another reason why CONFIG_HOTPLUG should go away. I had a hard time trying to disable it anyway ;-) The problem this time is lots of code assuming that a call to add_uevent_var() will guarantee that env->buflen > 0. This is not true if CONFIG_HOTPLUG is unset. So things like this end up overwriting env->envp_idx because the array index is -1: if (add_uevent_var(env, "MODALIAS=")) return -ENOMEM; len = input_print_modalias(&env->buf[env->buflen - 1], sizeof(env->buf) - env->buflen, dev, 0); Don't know what the best action is, given that there seem to be a *lot* of this around the kernel. This patch "fixes" the problem for me, but I don't know if it can be considered an appropriate fix. [ It is the correct fix for now, for 3.7 forcing CONFIG_HOTPLUG to always be on is the longterm fix, but it's too late for 3.6 and older kernels to resolve this that way - gregkh ] Reported-by:
-
