Add the debugfs framework to the driver and create a debugfs
command interface for each device.

example command:
"echo queue info > cmd" Query the packet forwarding queue information.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ptp_clock_register never return NULL, so no need check this
in cavium_ptp_probe.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A more featureful support for VSC8574 was recently added to the
Microsemi (mscc.c) driver. I checked that features supported in the
Vitesse driver are also supported in the Microsemi driver.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Linu Cherian says:

====================
octeontx2-af: CGX LMAC link bringup and cleanups

Patch 1: Code cleanup
Patch 2: Adds support for an unhandled hardware configuration
Patch 3: Preparatory patch for enabling cgx lmac links
Patch 4: Support for enabling cgx lmac links
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

- Added new CGX firmware interface API for sending link up/down
  commands

- Do link up for cgx lmac ports by default at the time of CGX
  driver probe. Since cgx link up in driver probe affects the
  Linux boot time, linkup procedure is kept threaded using
  workqueues.
  For this, a new cgx API cgx_lmac_linkup_start has been added.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added provision to unregister cgx event callbacks.
This enables the exit path to ensure event callbacks are
unregistered before workqueues get destroyed.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For this, cgx_id(struct cgx) definition has been changed to
reflect cgx port id instead of device instance id.
Now cgx_id can be directly used as channel offset for NPC configuration.
Assumptions on contiguous cgx port ids has been removed from
nix_calibrate_x2p as well.

As a side effect, allocation of conversion tables that were based
on cgx count are changed to cgx port id max value.
Tables would return NULL for invalid cgx ports.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* Do CGX init before NIX init
  This would add consistency in NIX code that depends on cgx ports

* Few other misc cleanups
  - rvu_cgx_probe renamed as rvu_cgx_init for consistency
  - rvu_cgx_exit wrapper added to take care of the exit path
  - Added error check on cgx_lmac_event_handler_init
  - Minor cleanups in cgx.h related to tab alignment
  - Removed redundant ids from enum cgx_cmd_id
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer hwdev is being dereferenced when declaring hwif , however, later
on hwdev is being null checked, hence we have dereference before null
check error. Fix this by assigning hwif and pdef only once hwdev has
been null checked.

Detected by CoverityScan, CID#1485581 ("Dereference before null check")

Fixes: 4a61abb1 ("net-next/hinic:add rx checksum offload for HiNIC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: patches 2018-11-22

here are more patches for SMC:
* patches 1-3 and 7 are cleanups without functional change
* patches 4-6 and 8 are optimizations of existing code
* patches 9 and 10 introduce and exploit LLC message DELETE RKEY
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When an rmb is no longer in use by a connection, unregister its rkey at
the remote peer with an LLC DELETE RKEY message. With this change,
unused buffers held in the buffer pool are no longer registered at the
remote peer. They are registered before the buffer is actually used and
unregistered when they are no longer used by a connection.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the infrastructure to send LLC messages of type DELETE RKEY to
unregister a shared memory region at the peer.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a send failed then don't start to wait for a response in
smc_llc_do_confirm_rkey.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For easier reading move the unlock of mutex smc_create_lgr_pending into
smc_listen_work(), i.e. into the function the mutex has been locked.
No functional change.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After sending one of the initial LLC messages CONFIRM LINK or
ADD LINK, there is already a wait for the LLC response. It does
not make sense to wait another long time for a CLC DECLINE. Thus
this patch introduces a shorter wait time for these cases.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a link is terminated that has never reached the active state,
there is no need to trigger an LLC DELETE LINK.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If connection initialization fails for the LLC CONFIRM LINK or the
LLC ADD LINK step, fallback to TCP should be enabled. Thus
the negative return code -EAGAIN should switch to a positive timeout
reason code in these cases, and the internal CLC socket should
not have a set sk_err.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to store the return value in sk_err, if it is
afterwards cleared again with sock_error(). This patch sets the
return value directly. Just cleanup, no functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smc_lgr_free() is just called inside smc_core.c. Make it static.
Just cleanup, no functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tcp_listen_worker is already initialized when socket is
created (in smc_sock_alloc()). Get rid of the duplicate
initialization in smc_listen(). No functional change.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fixes the smatch warning:

drivers/net/ethernet/marvell/mvneta.c:4252 mvneta_ethtool_set_eee() warn:
 unsigned 'eee->tx_lpi_timer' is never less than zero.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2018-11-21

This series contains updates to all of the Intel LAN drivers and
documentation.

Shannon Nelson updates the ixgbe kernel documentation to include IPsec
hardware offload.

Joe Perches cleans up whitespace issues in the igb driver.

Jesse update the netdev kernel documentation for NETIF_F_GSO_UDP_L4 to
align with the actual code.  Also aligned all the NAPI driver code for
all of the Intel drivers to implement the recommendations of Eric
Dumazet to check the return code of the napi_complete_done() to
determine whether or not to enable interrupts or exit poll.

Paul E. McKenney replaces synchronize_sched() with synchronize_rcu() for
ixgbe.

Sasha implements suggestions made by Joe Perches to remove obsolete code
and to use the dev_err() method.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We very often have few flows/chains to look at, and we
might increase GRO_HASH_BUCKETS to 32 or 64 in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Madalin Bucur says:

====================
dpaa_eth: add ethtool coalesce control

Add control of the DPAA portal interrupt coalescing settings from
ethtool.

changes from v2: read ithresh from HW, set previous values on failure
changes from v1: added range checking for the QMan APIs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow ethtool control of the DPAA QMan portal interrupt coalescing
settings.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check that the values received by the portal interrupt coalesce
change APIs are in range.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Read the DQRR interrupt threshold directly from the hardware.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Magnus Damm says:

====================
ravb: Duplex handling update V3

[PATCH v3 01/02] ravb: Do not announce HDX as supported
[PATCH v3 02/02] ravb: Clean up duplex handling

This series is V3 of duplex handling improvements for the Ethernet-AVB driver.

Previous versions of this series have been posted to linux-renesas-soc as RFC
so V3 is the first actual version to make it to netdev.

Based on the latest data sheet for R-Car Gen3 [1] and R-Car Gen2 [2]
the following information is part of the EthernetAVB-IF overview page:

Transfer speed: Supports transfer at 100 and 1000 Mbps
Mode: Full-duplex mode

It seems that the driver implementation is not matching the information
provided in the friendly data sheet, and on top of this during run-time
when changing PHY configuration of the link partner the Ethernet-AVB PHY
seems to want to announce unsupported modes.

[1] R-Car Series, 3rd Generation Rev.1.00 (Apr 2018)
[2] R-Car Series, 2nd Generation Rev.2.00 (Feb 2016)

Changes since V2:
- Updated patch 1/2 to make use of phy_remove_link_mode()
- Added Reviewed-by from Sergei - thanks!

Changes since V1:
- Updated patches to reflect input from Sergei and Geert - thanks!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since only full-duplex operation is supported by the
hardware, remove duplex handling code and keep the
register setting of ECMR.DM fixed at 1.

This updates the driver implementation to follow the
data sheet text "This bit should always be set to 1."

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the data sheet the Ethernet-AVB hardware in R-Car Gen3
and R-Car Gen2 SoCs do not support half duplex operation. So update
the driver to mark 100Mbit and 1Gbps HDX as unsupported.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the fw supports returning VIN/VIVLD in FW_VI_CMD save it
in port_info structure else retrieve these from viid and save
them  in port_info structure. Do the same for smt_idx from
FW_VI_MAC_CMD
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c5a54bbc ("net: bcmgenet: abort suspend on error")
mistakenly introduced register accesses that should not occur
in bcmgenet_wol_power_up_cfg().

Fixes: c5a54bbc ("net: bcmgenet: abort suspend on error")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Perform CQ initialization in the driver when the capability is supported
by the FW.  When passing the CQ to HW indicate that the CQ buffer has
been pre-initialized.

Doing so decreases CQ creation time.  Testing on P8 showed a single 2048
entry CQ creation time was reduced from ~395us to ~170us, which is
2.3x faster.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 3327a9c4 ("selftests: add functionals test for UDP GRO")
make use of ipv6 NAT, but such a feature is not currently implied by
selftests. Since the 'ip[6]tables' commands may actually create nft rules,
depending on the specific user-space version, let's pull both NF and
NFT nat modules plus the needed deps.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 3327a9c4 ("selftests: add functionals test for UDP GRO")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Add VxLAN learning support

This patchset adds VxLAN learning support in the mlxsw driver.

The first five patches from Petr add the required switchdev APIs which
allow device drivers to notify the VxLAN driver about learned / aged-out
FDB entries.

First in patch #1, an unnecessary argument is dropped from
__vxlan_fdb_delete().

In patches #2-#4, the VxLAN FDB handling code is extended to make
sending the switchdev events configurable; to mark user-added entries as
such; and to make sure HW-learned FDB entries do not take over
user-added ones.

Finally in patch #5, the necessary switchdev notifications are added and
handled by VxLAN, similarly to how this is handled in the bridge driver.

Patch #6 allows changing of the VxLAN's device ageing time since it is
useful for the selftest in the last patch.

Patch #7 adds support for querying bridge port flags of a given
netdevice, as a new entry should not be learned and notified to the
bridge driver in case learning is disabled on the bridge port.

Next patches gradually add learning support in mlxsw.

The last patch adds a new test case for VxLAN learning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test which checks that the VxLAN driver can learn FDB entries and
that these entries are correctly deleted and aged-out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test currently expects that a configuration which includes a VxLAN
device with learning enabled to fail.

Previous patches enabled VxLAN learning in mlxsw, so change the test
accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up until now the driver returned an error when learning was enabled on a
VxLAN device enslaved to an offloaded bridge.

Previous patches added VxLAN learning support, so remove the check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow users to delete learned FDB entries from the bridge's FDB before
enabling VxLAN learning.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Start processing two new entry types in addition to current ones:
* Learned unicast tunnel entry
* Aged-out unicast tunnel entry

In both cases the device reports on a new {MAC, FID, IP address} tuple
that was learned / aged-out. Based on this notification, the driver
instructs the device to add / delete the entry to / from its database.

The driver also makes sure to notify the bridge and VxLAN drivers about
the new entry.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>