Follow sram/sram.yaml to update the sram node name.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The clocks and clocks-names are not documented in binding doc,
and the clk-imx8ulp driver not use the undocumented property,
so drop them.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Properties are not documented so lead to the following error:
'#address-cells', '#size-cells', 'interrupts' do not match any of the regexes: 'pinctrl-[0-9]+'

Fix this by removing unneeded properties.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In order to enable (PD and data) role switching on the Librem 5 phone,
add the usb-role-switch property to imx8mq's dwc3 node.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the connector properties to the USB type-c stanza to enable (PD)
role-switching on the Librem 5 phone.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Describe the RGB notification leds on the Librem 5 phone.
Use the common defines so we're sure to adhere to the common patterns,
use predefined led colors and functions so we're being warned in case
of deprecations.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Describe the focus motor that will be used for the rear camera - even
though the rear camera sensor driver is not yet in the mainline. The
focus motor is a separate device and can be controlled already.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In order for the LS1028A based boards to benefit from support for
multiple CPU ports, the second DSA master and its associated CPU port
must be enabled in the device trees. This does not change the default
CPU port from the current port 4.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LS1028A switch has 2 internal links to the ENETC controller.

With DSA's ability to support multiple CPU ports, we should mark both
ENETC ports as DSA masters.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Since the CPU port 4 of the switch is hardwired inside the SoC to go to
the enetc port 2, this shouldn't be something that the board files need
to set (but whether that CPU port is used or not is another discussion).

So move the DSA "ethernet" property to the common dtsi.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PCIe support on i.MX8MP EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8MP PCIe support.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes the following error:

arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h: error: do not set
 execute permissions for source files
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SNVS LPGPR bindings to MX8M Plus, the LPGPR is used to store
e.g. boot counter.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device trees for one of a number of MSC's (parent company, Avnet)
variants of the SM2S-IMX8PLUS system on module along with the compatible
SM2S-SK-AL-EP1 carrier board. As the name suggests, this family of SoMs use
the NXP i.MX8MP SoC and provide the SMARC module interface.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix the Amarula Solutions typo mistake in license text for Engicam
i.MX8M boards add in below commits.

commit <60ac3526> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M
Mini SoM")
commit <aec8ad34> ("arm64: dts: imx8mp: Add Engicam i.Core MX8M
Plus EDIMM2.2 Starter Kit")
commit <eefe06b2> ("arm64: dts: imx8mp: Add Engicam i.Core MX8M
Plus SoM")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8 LPI2C requires both PER and IPG clock, so add the missed IPG clk.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the Kontron Electronics SL i.MX8MM OSM-S SoM
and the matching baseboard BL i.MX8MM OSM-S.

The SoM hardware complies to the Open Standard Module (OSM) 1.0
specification, size S (https://sget.org/standards/osm).
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is the layout used by the bootloader. Add it to the kernel
devicetree to make the same layout available in Linux and have
the devicetrees synced.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Improve the naming of the regulators to contain the voltage rail
names from the schematic.
Suggested-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

For some reason there is a problem with finding a DDR configuration
that works on all operating points and all LPDDR4 types used on the
SoM. Therefore the bootloader currently doesn't configure the lowest
of the three operating points. Let's also skip this in the kernel
devicetree to make sure it isn't used.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.

Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The official naming includes "SL" (SoM-Line) or "BL" (Board-Line).
By updating we make sure, that we can maintain this more easily in
future and make sure that the proper devicetree can be selected for
the hardware.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8MP VPU blk ctrl node
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8MP PGC nodes for vpu, which are used to supply power for VPU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the cpu-supply property to all CPU nodes to enable the cpufreq
driver.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The GW7903-C revision introduced two additional GPIO's for controlling
the digital I/O direction. Add them.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'oscillator-frequency' property is not documented and it is
not used anywhere. Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SoM compatible string into i.MX8MP DHCOM PDK2 compatible strings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This PHY is not used on PDK2, the header was added due to copy-paste
error, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add information about which exact SoM variant is used on which PDK2 variant.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx8mq-mnt-reform2.dts:213: check: Please don't use
 multiple blank lines
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warning:

arch/arm/boot/dts/imx8mp-verdin.dtsi:281: check: Please don't use
 multiple blank lines
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Avoid the following checkpatch warning:

Found possible blank line(s) at end of file
 'arch/arm/boot/dts/imx8mm-venice-gw72xx-0x.dts'
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable the fec on i.MX8ULP EVK board.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the fec support on i.MX8ULP platforms.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add interconnect property for hsio blk ctrl
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add interconnect property for media blk ctrl
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX8DXL is a device targeting the automotive and industrial market
segments. The chip is designed to achieve both high performance and
low power consumption. It has a dual (2x) Cortex-A35 processor.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>