- 29 Nov, 2013 40 commits
-
-
Takashi Iwai authored
commit d183b4fc upstream. snd_hda_codec_reset() is called either in resetting the whole setup at error paths or hwdep clear/reconfig sysfs triggers. But all of these don't assume that the power has to be off, rather they want to keep the power state unchanged (e.g. reconfig_codec() calls the power up/down by itself). Thus, unconditionally clearing the power state in snd_hda_codec_reset() leads to the inconsistency, confuses the further operation. This patch gets rid of the lines doing that bad thing. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Takashi Iwai authored
commit 7a3e6107 upstream. The only EAPD on AD1986A is on NID 0x1b where usually the speaker. But this doesn't control only the speaker amp but may influence on all outputs, e.g. Lenovo N100 laptop seems to have this issue. Signed-off-by:
-
Takashi Iwai authored
commit 468ac413 upstream. We don't change the EAPD bit in set_pin_eapd() if keep_eapd_on flag is set by the codec driver and enable is false. But, we also apply the flipping of enable value according to inv_eapd flag in the same function, and this confused the former check, handled as if it's turned ON. The inverted EAPD check must be applied after keep_eapd_on check, instead. Signed-off-by:
-
David Henningsson authored
commit 5959a6bc upstream. In case there is both a multifunction headset jack and a Line Out jack, automuting was not working properly from the Line Out jack. This patch fixes that issue. BugLink: https://bugs.launchpad.net/bugs/1250377Tested-by:
Cyrus Lien <cyrus.lien@canonical.com> Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Takashi Iwai authored
commit 487a588d upstream. BIOS on ASUS W5A laptop with ALC880 codec doesn't provide any pin configurations, so we have to set up all pins manually. Reported-and-tested-by:
nb <nb@dagami.org> Signed-off-by:
-
Takashi Iwai authored
commit 8f42d769 upstream. It's a superset of the existing CX2075x codecs, so we can reuse the existing parser code. Signed-off-by:
-
David Henningsson authored
commit d5b6b65e upstream. Some HP machines with Realtek codecs have mute LEDs connected to VREF pins. However when these go into runtime suspend, the pin powers down and its pin control is disabled, thus disabling the LED too. This patch fixes that issue by making sure that the pin stays in D0 with correct pin control. BugLink: https://bugs.launchpad.net/bugs/1248465Tested-by:
Franz Hsieh <franz.hsieh@canonical.com> Signed-off-by:
-
Takashi Iwai authored
commit 33499a15 upstream. Haswell HDMI audio controllers seem to get stuck when unaligned buffer size is used. Let's enable the buffer alignment for the corresponding entries. Since AZX_DCAPS_INTEL_PCH contains AZX_DCAPS_BUFSIZE that disables the buffer alignment forcibly, define AZX_DCAPS_INTEL_HASWELL and put the necessary AZX_DCAPS bits there. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60769Reported-by:
Alexander E. Patrakov <patrakov@gmail.com> Signed-off-by:
-
Takashi Iwai authored
commit 24eff328 upstream. BIOS on Acer TravelMate 6293 doesn't set up the SPDIF output pin correctly as default, so enable it via a fixup entry. Reported-and-tested-by:
Hagen Heiduck <heiduck.suse@fmail.postpro.net> Signed-off-by:
-
Takashi Iwai authored
commit a1114a8c upstream. Add a bitmask to hda_gen_spec indicating NIDs to exclude from the possible volume controls. That is, when the bit is set, the NID corresponding to the bit won't be picked as an output volume control any longer. Basically this is just a band-aid for working around the issue found with CS4208 codec, where only the headphone pin has a volume AMP with different dB steps. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811Signed-off-by:
-
Kailang Yang authored
commit 1d04c9de upstream. It's just another variant of ALC269 & co. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
-
Takashi Iwai authored
commit 092f9cd1 upstream. msnd_pinnacle.c is used for both snd-msnd-pinnacle and snd-msnd-classic drivers, and both should have different driver names. Using the same driver name results in the sysfs warning for duplicated entries like kobject: 'msnd-pinnacle.7' (cec33408): kobject_release, parent (null) (delayed) kobject: 'msnd-pinnacle' (cecd4980): kobject_release, parent cf3ad9b0 (delayed) ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:486 sysfs_warn_dup+0x7d/0xa0() sysfs: cannot create duplicate filename '/bus/isa/drivers/msnd-pinnacle' ...... Reported-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
Takashi Iwai authored
commit 885845d7 upstream. The commit [8fe7b65a: ALSA: hda - Apply GPIO setup for MacBooks with CS4208] added a fixup entry matching with the vendor id 0x106b. This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID vendor id matches before evaluating the codec SSIDs. We had a similar issue on Mac with Sigmatel codecs, and solve this problem again similarly, by introducing a skeleton entry matching with the all MacBooks, then remap to the right one. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401 Fixes: 8fe7b65a ('ALSA: hda - Apply GPIO setup for MacBooks with CS4208') Signed-off-by:
-
Takashi Iwai authored
commit 8fe7b65a upstream. Apply the existing GPIO0 fixup as default for MacBooks with CS4208 codec. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401Signed-off-by:
-
Takashi Iwai authored
commit 6408eac2 upstream. The current code may access to the already freed object. The input device must be accessed and unregistered before freeing the top level sound object. Signed-off-by:
-
Vinod Koul authored
commit f44f2a54 upstream. The drain and drain_notify callback were blocked by low level driver until the draining was complete. Due to this being invoked with big fat mutex held, others ops like reading timestamp, calling pause, drop were blocked. So to fix this we add a new snd_compr_drain_notify() API. This would be required to be invoked by low level driver when drain or partial drain has been completed by the DSP. Thus we make the drain and partial_drain callback as non blocking and driver returns immediately after notifying DSP. The waiting is done while releasing the lock so that other ops can go ahead. [ The commit 917f4b5c was wrongly applied from the preliminary patch. This commit corrects to the final version. Sorry for inconvenience! -- tiwai ] Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Vinod Koul authored
commit 917f4b5c upstream. The drain and drain_notify callback were blocked by low level driver untill the draining was complete. Due to this being invoked with big fat mutex held, others ops like reading timestamp, calling pause, drop were blocked. So to fix this we add a new snd_compr_drain_notify() API. This would be required to be invoked by low level driver when drain or partial drain has been completed by the DSP. Thus we make the drain and partial_drain callback as non blocking and driver returns immediately after notifying DSP. The waiting is done while relasing the lock so that other ops can go ahead. Signed-off-by:
-
Takashi Iwai authored
commit 9b389a8a upstream. The probe code of snd-usb-6fire driver overrides the devices[] pointer wrongly without checking whether it's already occupied or not. This would screw up the device disconnection later. Spotted by coverity CID 141423. Signed-off-by:
-
Kees Cook authored
commit d049f74f upstream. The get_dumpable() return value is not boolean. Most users of the function actually want to be testing for non-SUID_DUMP_USER(1) rather than SUID_DUMP_DISABLE(0). The SUID_DUMP_ROOT(2) is also considered a protected state. Almost all places did this correctly, excepting the two places fixed in this patch. Wrong logic: if (dumpable == SUID_DUMP_DISABLE) { /* be protective */ } or if (dumpable == 0) { /* be protective */ } or if (!dumpable) { /* be protective */ } Correct logic: if (dumpable != SUID_DUMP_USER) { /* be protective */ } or if (dumpable != 1) { /* be protective */ } Without this patch, if the system had set the sysctl fs/suid_dumpable=2, a user was able to ptrace attach to processes that had dropped privileges to that user. (This may have been partially mitigated if Yama was enabled.) The macros have been moved into the file that declares get/set_dumpable(), which means things like the ia64 code can see them too. CVE-2013-2929 Reported-by:
Vasily Kulikov <segoon@openwall.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Mimi Zohar authored
commit 08de59eb upstream. This reverts commit 4c2c3927. Everything in the initramfs should be measured and appraised, but until the initramfs has extended attribute support, at least measured. Signed-off-by:
Mimi Zohar <zohar@us.ibm.com> Signed-off-by:
-
Hans de Goede authored
commit b1a80144 upstream. Many btusb devices have 2 modes, a hid mode and a bluetooth hci mode. These devices default to hid mode for BIOS use. This means that after having been reset they will revert to HID mode, and are no longer usable as a HCI. Therefor it is a very bad idea to just blindly make reset_resume point to the regular resume handler. Note that the btusb driver has no clue how to switch these devices from hid to hci mode, this is done in userspace through udev rules, so the proper way to deal with this is to not have a reset-resume handler and instead let the usb-system re-enumerate the device, and re-run the udev rules. I must also note, that the commit message for the commit causing this problem has a very weak motivation for the change: "Add missing reset_resume dev_pm_ops. Missing reset_resume results in the following message after power management device test. This change sets reset_resume to btusb_resume(). [ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb? [ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?" Making a change solely to silence a warning while also changing important behavior (normal resume handling versus re-enumeration) requires a commit message with a proper explanation why it is safe to do so, which clearly lacks here, and unsurprisingly it turns out to not be safe to make this change. Reverting the commit in question fixes bt no longer working on my Dell E6430 after a suspend/resume, and I believe it likely also fixes the following bugs: https://bugzilla.redhat.com/show_bug.cgi?id=988481 https://bugzilla.redhat.com/show_bug.cgi?id=1010649 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1213239 This reverts commit 502f7696. Cc: Shuah Khan <shuah.kh@samsung.com> Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
-
Stanislaw Gruszka authored
commit 3d8bfe14 upstream. Since: commit 36323f81 Author: Thomas Huehn <thomas@net.t-labs.tu-berlin.de> Date: Mon Jul 23 21:33:42 2012 +0200 mac80211: move TX station pointer and restructure TX we do not pass sta pointer to rt2x00queue_create_tx_descriptor_ht(), hence we do not correctly set station WCID and AMPDU density parameters. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Gabor Juhos authored
commit 0beb1bbf upstream. In commit 3d81535e (rt2800: 5592: add chip specific vgc calculations) the rt2800_link_tuner function has been modified to adjust VGC level for the RT5592 chipset. On the RT5592 chipset, the VGC level must be adjusted only if rssi is greater than -65. However the current code adjusts the VGC value by 0x10 regardless of the actual chipset if the rssi value is between -80 and -65. Fix the broken behaviour by reordering the if-else statements. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Acked-by:
Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by:
-
Stanislaw Gruszka authored
commit 5671ab05 upstream. Fix random kernel panic with below messages when remove dongle. [ 2212.355447] BUG: unable to handle kernel NULL pointer dereference at 0000000000000250 [ 2212.355527] IP: [<ffffffffa02667f2>] rt2x00usb_kick_tx_entry+0x12/0x160 [rt2x00usb] [ 2212.355599] PGD 0 [ 2212.355626] Oops: 0000 [#1] SMP [ 2212.355664] Modules linked in: rt2800usb rt2x00usb rt2800lib crc_ccitt rt2x00lib mac80211 cfg80211 tun arc4 fuse rfcomm bnep snd_hda_codec_realtek snd_hda_intel snd_hda_codec btusb uvcvideo bluetooth snd_hwdep x86_pkg_temp_thermal snd_seq coretemp aesni_intel aes_x86_64 snd_seq_device glue_helper snd_pcm ablk_helper videobuf2_vmalloc sdhci_pci videobuf2_memops videobuf2_core sdhci videodev mmc_core serio_raw snd_page_alloc microcode i2c_i801 snd_timer hid_multitouch thinkpad_acpi lpc_ich mfd_core snd tpm_tis wmi tpm tpm_bios soundcore acpi_cpufreq i915 i2c_algo_bit drm_kms_helper drm i2c_core video [last unloaded: cfg80211] [ 2212.356224] CPU: 0 PID: 34 Comm: khubd Not tainted 3.12.0-rc3-wl+ #3 [ 2212.356268] Hardware name: LENOVO 3444CUU/3444CUU, BIOS G6ET93WW (2.53 ) 02/04/2013 [ 2212.356319] task: ffff880212f687c0 ti: ffff880212f66000 task.ti: ffff880212f66000 [ 2212.356392] RIP: 0010:[<ffffffffa02667f2>] [<ffffffffa02667f2>] rt2x00usb_kick_tx_entry+0x12/0x160 [rt2x00usb] [ 2212.356481] RSP: 0018:ffff880212f67750 EFLAGS: 00010202 [ 2212.356519] RAX: 000000000000000c RBX: 000000000000000c RCX: 0000000000000293 [ 2212.356568] RDX: ffff8801f4dc219a RSI: 0000000000000000 RDI: 0000000000000240 [ 2212.356617] RBP: ffff880212f67778 R08: ffffffffa02667e0 R09: 0000000000000002 [ 2212.356665] R10: 0001f95254ab4b40 R11: ffff880212f675be R12: ffff8801f4dc2150 [ 2212.356712] R13: 0000000000000000 R14: ffffffffa02667e0 R15: 000000000000000d [ 2212.356761] FS: 0000000000000000(0000) GS:ffff88021e200000(0000) knlGS:0000000000000000 [ 2212.356813] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 2212.356852] CR2: 0000000000000250 CR3: 0000000001a0c000 CR4: 00000000001407f0 [ 2212.356899] Stack: [ 2212.356917] 000000000000000c ffff8801f4dc2150 0000000000000000 ffffffffa02667e0 [ 2212.356980] 000000000000000d ffff880212f677b8 ffffffffa03a31ad ffff8801f4dc219a [ 2212.357038] ffff8801f4dc2150 0000000000000000 ffff8800b93217a0 ffff8801f49bc800 [ 2212.357099] Call Trace: [ 2212.357122] [<ffffffffa02667e0>] ? rt2x00usb_interrupt_txdone+0x90/0x90 [rt2x00usb] [ 2212.357174] [<ffffffffa03a31ad>] rt2x00queue_for_each_entry+0xed/0x170 [rt2x00lib] [ 2212.357244] [<ffffffffa026701c>] rt2x00usb_kick_queue+0x5c/0x60 [rt2x00usb] [ 2212.357314] [<ffffffffa03a3682>] rt2x00queue_flush_queue+0x62/0xa0 [rt2x00lib] [ 2212.357386] [<ffffffffa03a2930>] rt2x00mac_flush+0x30/0x70 [rt2x00lib] [ 2212.357470] [<ffffffffa04edded>] ieee80211_flush_queues+0xbd/0x140 [mac80211] [ 2212.357555] [<ffffffffa0502e52>] ieee80211_set_disassoc+0x2d2/0x3d0 [mac80211] [ 2212.357645] [<ffffffffa0506da3>] ieee80211_mgd_deauth+0x1d3/0x240 [mac80211] [ 2212.357718] [<ffffffff8108b17c>] ? try_to_wake_up+0xec/0x290 [ 2212.357788] [<ffffffffa04dbd18>] ieee80211_deauth+0x18/0x20 [mac80211] [ 2212.357872] [<ffffffffa0418ddc>] cfg80211_mlme_deauth+0x9c/0x140 [cfg80211] [ 2212.357913] [<ffffffffa041907c>] cfg80211_mlme_down+0x5c/0x60 [cfg80211] [ 2212.357962] [<ffffffffa041cd18>] cfg80211_disconnect+0x188/0x1a0 [cfg80211] [ 2212.358014] [<ffffffffa04013bc>] ? __cfg80211_stop_sched_scan+0x1c/0x130 [cfg80211] [ 2212.358067] [<ffffffffa03f8954>] cfg80211_leave+0xc4/0xe0 [cfg80211] [ 2212.358124] [<ffffffffa03f8d1b>] cfg80211_netdev_notifier_call+0x3ab/0x5e0 [cfg80211] [ 2212.358177] [<ffffffff815140f8>] ? inetdev_event+0x38/0x510 [ 2212.358217] [<ffffffff81085a94>] ? __wake_up+0x44/0x50 [ 2212.358254] [<ffffffff8155995c>] notifier_call_chain+0x4c/0x70 [ 2212.358293] [<ffffffff81081156>] raw_notifier_call_chain+0x16/0x20 [ 2212.358361] [<ffffffff814b6dd5>] call_netdevice_notifiers_info+0x35/0x60 [ 2212.358429] [<ffffffff814b6ec9>] __dev_close_many+0x49/0xd0 [ 2212.358487] [<ffffffff814b7028>] dev_close_many+0x88/0x100 [ 2212.358546] [<ffffffff814b8150>] rollback_registered_many+0xb0/0x220 [ 2212.358612] [<ffffffff814b8319>] unregister_netdevice_many+0x19/0x60 [ 2212.358694] [<ffffffffa04d8eb2>] ieee80211_remove_interfaces+0x112/0x190 [mac80211] [ 2212.358791] [<ffffffffa04c585f>] ieee80211_unregister_hw+0x4f/0x100 [mac80211] [ 2212.361994] [<ffffffffa03a1221>] rt2x00lib_remove_dev+0x161/0x1a0 [rt2x00lib] [ 2212.365240] [<ffffffffa0266e2e>] rt2x00usb_disconnect+0x2e/0x70 [rt2x00usb] [ 2212.368470] [<ffffffff81419ce4>] usb_unbind_interface+0x64/0x1c0 [ 2212.371734] [<ffffffff813b446f>] __device_release_driver+0x7f/0xf0 [ 2212.374999] [<ffffffff813b4503>] device_release_driver+0x23/0x30 [ 2212.378131] [<ffffffff813b3c98>] bus_remove_device+0x108/0x180 [ 2212.381358] [<ffffffff813b0565>] device_del+0x135/0x1d0 [ 2212.384454] [<ffffffff81417760>] usb_disable_device+0xb0/0x270 [ 2212.387451] [<ffffffff8140d9cd>] usb_disconnect+0xad/0x1d0 [ 2212.390294] [<ffffffff8140f6cd>] hub_thread+0x63d/0x1660 [ 2212.393034] [<ffffffff8107c860>] ? wake_up_atomic_t+0x30/0x30 [ 2212.395728] [<ffffffff8140f090>] ? hub_port_debounce+0x130/0x130 [ 2212.398412] [<ffffffff8107baa0>] kthread+0xc0/0xd0 [ 2212.401058] [<ffffffff8107b9e0>] ? insert_kthread_work+0x40/0x40 [ 2212.403639] [<ffffffff8155de3c>] ret_from_fork+0x7c/0xb0 [ 2212.406193] [<ffffffff8107b9e0>] ? insert_kthread_work+0x40/0x40 [ 2212.408732] Code: 24 58 08 00 00 bf 80 00 00 00 e8 3a c3 e0 e0 5b 41 5c 5d c3 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 41 54 53 <48> 8b 47 10 48 89 fb 4c 8b 6f 28 4c 8b 20 49 8b 04 24 4c 8b 30 [ 2212.414671] RIP [<ffffffffa02667f2>] rt2x00usb_kick_tx_entry+0x12/0x160 [rt2x00usb] [ 2212.417646] RSP <ffff880212f67750> [ 2212.420547] CR2: 0000000000000250 [ 2212.441024] ---[ end trace 5442918f33832bce ]--- Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
Felix Fietkau authored
commit b4089d6d upstream. Commit "rt2x00: fix HT TX descriptor settings regression" assumes that the control parameter to rt2x00mac_tx is always non-NULL. There is an internal call in rt2x00lib_bc_buffer_iter where NULL is passed. Fix the resulting crash by adding an initialized dummy on-stack ieee80211_tx_control struct. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Acked-by:
-
K. Y. Srinivasan authored
commit 565ce642 upstream. Rescind of subchannels were not being correctly handled. Fix the bug. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
-
Kees Cook authored
commit 629c66a2 upstream. When tests were added to lkdtm that grew the stack frame, the stack corruption test stopped working. This isolates the test in its own function, and forces it not to be inlined. Signed-off-by:
-
Ian Abbott authored
commit 67aa4acb upstream. `comedi_alloc_spriv()` allocates private storage for a comedi subdevice and sets the `SRF_FREE_SPRIV` flag in the `runflags` member of the subdevice to allow the private storage to be automatically freed when the comedi device is being cleaned up. Unfortunately, the flag gets clobbered by `do_cmd_ioctl()` which calls `comedi_set_subdevice_runflags()` with a mask value `~0` and only the `SRF_USER` and `SRF_RUNNING` flags set, all the other SRF flags being cleared. Change the calls to `comedi_set_subdevice_runflags()` that currently use a mask value of `~0` to use a more relevant mask value. For `do_cmd_ioctl()`, the relevant SRF flags are `SRF_USER`, `SRF_ERROR` and `SRF_RUNNING`. (At one time, `SRF_RT` would be included in that set of flags, but it is no longer used.) For `comedi_alloc_spriv()` replace the call to `comedi_set_subdevice_runflags()` with a simple OR-assignment to avoid unnecessary use of a spin-lock. Signed-off-by:
Ian Abbott <abbotti@mev.co.uk> Signed-off-by:
-
Larry Finger authored
commit 0d1206be upstream. The latest version of NetworkManager does not recognize the device as wireless without this change. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Rashika Kheria authored
commit 46a51c80 upstream. This patch fixes the bug in reset_store caused by accessing NULL pointer. The bdev gets its value from bdget_disk() which could fail when memory pressure is severe and hence can return NULL because allocation of inode in bdget could fail. Hence, this patch introduces a check for bdev to prevent reference to a NULL pointer in the later part of the code. It also removes unnecessary check of bdev for fsync_bdev(). Acked-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
Rashika Kheria <rashika.kheria@gmail.com> Acked-by:
Minchan Kim <minchan@kernel.org> Signed-off-by:
-
Rafael J. Wysocki authored
commit 176a88d7 upstream. According to the ACPI spec (5.0, Section 6.3.5), the "Device insertion in progress (pending)" (0x80) _OST status code is reserved for the "Insertion Processing" (0x200) source event which is "a result of an OSPM action". Specifically, it is not a notification, so that status code should not be used during notification processing, which unfortunately is done by acpi_scan_bus_device_check(). For this reason, drop the ACPI_OST_SC_INSERT_IN_PROGRESS _OST status evaluation from there (it was a mistake to put it in there in the first place). Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Rafael J. Wysocki authored
commit 2441191a upstream. It is required to do get_device() on the struct acpi_device in question before passing it to acpi_bus_hot_remove_device() through acpi_os_hotplug_execute(), because acpi_bus_hot_remove_device() calls acpi_scan_hot_remove() that does put_device() on that object. The ACPI PCI root removal routine, handle_root_bridge_removal(), doesn't do that, which may lead to premature freeing of the device object or to executing put_device() on an object that has been freed already. Fix this problem by making handle_root_bridge_removal() use get_device() as appropriate. Signed-off-by:
Toshi Kani <toshi.kani@hp.com> Signed-off-by:
-
Aaron Lu authored
commit 2c62333a upstream. Some firmware doesn't initialize initial backlight level to a proper value and _BQC will return 0 on first time evaluation. We used to be able to detect such incorrect value with our code logic, as value 0 normally isn't a valid value in _BCL. But with the introduction of Win8, firmware begins to fill _BCL with values from 0 to 100, now 0 becomes a valid value but that value will make user's screen black. This patch test initial _BQC for value 0, if such a value is returned, do not use it. References: https://bugzilla.kernel.org/show_bug.cgi?id=64031 References: https://bugzilla.kernel.org/show_bug.cgi?id=61231 References: https://bugzilla.kernel.org/show_bug.cgi?id=63111Reported-by:
Qingshuai Tian <qingshuai.tian@intel.com> Tested-by: Aaron Lu <aaron.lu@intel.com> # on "Idealpad u330p" Reported-and-tested-by: <erno@iki.fi> # on "Acer Aspire V5-573G" Reported-and-tested-by: Kirill Tkhai <tkhai@yandex.ru> # on "HP 250 G1" Signed-off-by:
Aaron Lu <aaron.lu@intel.com> Signed-off-by:
-
Puneet Kumar authored
commit 36b15875 upstream. A bug was introduced by commit b76b51ba ('ACPI / EC: Add more debug info and trivial code cleanup') that erroneously caused the struct member to be accessed before acquiring the required lock. This change fixes it by ensuring the lock acquisition is done first. Found by Aaron Durbin <adurbin@chromium.org> Fixes: b76b51ba ('ACPI / EC: Add more debug info and trivial code cleanup') References: http://crbug.com/319019Signed-off-by:
Puneet Kumar <puneetster@chromium.org> Reviewed-by:
Aaron Durbin <adurbin@chromium.org> [olof: Commit message reworded a bit] Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Steven Rostedt authored
commit 12ae030d upstream. The current default perf paranoid level is "1" which has "perf_paranoid_kernel()" return false, and giving any operations that use it, access to normal users. Unfortunately, this includes function tracing and normal users should not be allowed to enable function tracing by default. The proper level is defined at "-1" (full perf access), which "perf_paranoid_tracepoint_raw()" will only give access to. Use that check instead for enabling function tracing. Reported-by:
Dave Jones <davej@redhat.com> Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Tested-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Peter Zijlstra authored
commit ea811747 upstream. Mike reported that commit 7d1a9417 ("x86: Use generic idle loop") regressed several workloads and caused excessive reschedule interrupts. The patch in question failed to notice that the x86 code had an inverted sense of the polling state versus the new generic code (x86: default polling, generic: default !polling). Fix the two prominent x86 mwait based idle drivers and introduce a few new generic polling helpers (fixing the wrong smp_mb__after_clear_bit usage). Also switch the idle routines to using tif_need_resched() which is an immediate TIF_NEED_RESCHED test as opposed to need_resched which will end up being slightly different. Reported-by:
Mike Galbraith <bitbucket@online.de> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Cc: lenb@kernel.org Cc: tglx@linutronix.de Link: http://lkml.kernel.org/n/tip-nc03imb0etuefmzybzj7sprf@git.kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Suman Anna authored
commit 6423d6df upstream. The hwmod init sequence involves initializing and idling all the hwmods during bootup. If a module class has sysconfig, the init sequence utilizes the module register base for performing any sysc configuration. The module address space is being removed from hwmod database and retrieved from the <reg> property of the corresponding DT node. If a hwmod does not have its corresponding DT node defined and the memory address space is not defined in the corresponding omap_hwmod_ocp_if, then the module register target address space would be NULL and any sysc programming would result in a NULL pointer dereference and a kernel boot hang. Handle this scenario by checking for a valid module address space during the _init of each hwmod, and leaving it in the registered state if no module register address base is defined in either of the hwmod data or the DT data. Signed-off-by:
Suman Anna <s-anna@ti.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by:
Nishanth Menon <nm@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com> [paul@pwsan.com: use -ENXIO rather than -ENOMEM to indicate a missing address space error; fixed checkpatch.pl problem] Signed-off-by:
Paul Walmsley <paul@pwsan.com> Signed-off-by:
-
Takashi Iwai authored
commit cab66613 upstream. SNDRV_CARDS can be specified via Kconfig since 3.11 kernel, so this can be over 32bit integer range, which leads to a build error. Signed-off-by:
Matthew Garrett <matthew.garrett@nebula.com> Signed-off-by:
-
Ben Skeggs authored
commit 13d2b35a upstream. Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Cc: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
-
John Stultz authored
commit 59573240 upstream. Hopefully this isn't too late for 3.12. In commit 7dc19d5a (convert shrinkers to new count/scan API) the return value to PURGE_ALL_CACHES was dropped, causing -EPERM to always be returned. This patch re-adds the ret assignment, setting it to the the ashmem_shrink_count(), which is the lru_count. (Sorry this was missed in the review!) Fixes: 7dc19d5a ("convert shrinkers to new count/scan API") Cc: Colin Cross <ccross@android.com> Cc: Android Kernel Team <kernel-team@android.com> Cc: Glauber Costa <glommer@openvz.org> Reported-by:
YongQin Liu <yongqin.liu@linaro.org> Signed-off-by:
John Stultz <john.stultz@linaro.org> Acked-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
-
