pos is redundant (it's iocb->ki_pos), and iov/nr_segs/count are taken
care of by lifting iov_iter into the caller.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Now It Can Be Done(tm) - we don't need to do iov_shorten() in
generic_file_direct_write() anymore, now that all ->direct_IO()
instances are converted to proper iov_iter methods and honour
iter->count and iter->iov_offset properly.

Get rid of count/ocount arguments of generic_file_direct_write(),
while we are at it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... and don't open-code iov_iter_alignment() there
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

same as iov_iter_get_pages(), except that pages array is allocated
(kmalloc if possible, vmalloc if that fails) and left for caller to
free.  Lustre and NFS ->direct_IO() switched to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

counts the pages covered by iov_iter, up to given limit.
do_block_direct_io() and fuse_iter_npages() switched to
it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... to fuse_direct_{read,write}().  ->direct_IO() path uses the
iov_iter passed by the caller instead.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

iov_iter_get_pages(iter, pages, maxsize, &start) grabs references pinning
the pages of up to maxsize of (contiguous) data from iter.  Returns the
amount of memory grabbed or -error.  In case of success, the requested
area begins at offset start in pages[0] and runs through pages[1], etc.
Less than requested amount might be returned - either because the contiguous
area in the beginning of iterator is smaller than requested, or because
the kernel failed to pin that many pages.

direct-io.c switched to using iov_iter_get_pages()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

For now, just use the same thing we pass to ->direct_IO() - it's all
iovec-based at the moment.  Pass it explicitly to iov_iter_init() and
account for kvec vs. iovec in there, by the same kludge NFS ->direct_IO()
uses.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

iov_iter-using variant of generic_file_aio_read().  Some callers
converted.  Note that it's still not quite there for use as ->read_iter() -
we depend on having zero iter->iov_offset in O_DIRECT case.  Fortunately,
that's true for all converted callers (and for generic_file_aio_read() itself).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

returns the value aligned as badly as the worst remaining segment
in iov_iter is.  Use instead of open-coded equivalents.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

the thing is, we want to advance what's given to ->direct_IO() as we
are forming the request; however, the callers care about the amount
of data actually transferred, not the amount we tried to transfer.
It's more convenient to allow ->direct_IO() instances do use
iov_iter_advance() on the copy of iov_iter, leaving the actual
advancing of the original to caller.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

all callers have iov_length(iter->iov, iter->nr_segs) == iov_iter_count(iter)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

unmodified, for now
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

all callers of ->aio_read() and ->aio_write() have iov/nr_segs already
checked - generic_segment_checks() done after that is just an odd way
to spell iov_length().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

all callers can use copy_page_from_iter() and it actually simplifies
them.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Merge misc fixes from Andrew Morton:
 "13 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  agp: info leak in agpioc_info_wrap()
  fs/affs/super.c: bugfix / double free
  fanotify: fix -EOVERFLOW with large files on 64-bit
  slub: use sysfs'es release mechanism for kmem_cache
  revert "mm: vmscan: do not swap anon pages just because free+file is low"
  autofs: fix lockref lookup
  mm: filemap: update find_get_pages_tag() to deal with shadow entries
  mm/compaction: make isolate_freepages start at pageblock boundary
  MAINTAINERS: zswap/zbud: change maintainer email address
  mm/page-writeback.c: fix divide by zero in pos_ratio_polynom
  hugetlb: ensure hugepage access is denied if hugepages are not supported
  slub: fix memcg_propagate_slab_attrs
  drivers/rtc/rtc-pcf8523.c: fix month definition

On 64 bit systems the agp_info struct has a 4 byte hole between
->agp_mode and ->aper_base.  We need to clear it to avoid disclosing
stack information to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 842a859d ("affs: use ->kill_sb() to simplify ->put_super()
and failure exits of ->mount()") adds .kill_sb which frees sbi but
doesn't remove sbi free in case of parse_options error causing double
free+random crash.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>	[3.14.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On 64-bit systems, O_LARGEFILE is automatically added to flags inside
the open() syscall (also openat(), blkdev_open(), etc).  Userspace
therefore defines O_LARGEFILE to be 0 - you can use it, but it's a
no-op.  Everything should be O_LARGEFILE by default.

But: when fanotify does create_fd() it uses dentry_open(), which skips
all that.  And userspace can't set O_LARGEFILE in fanotify_init()
because it's defined to 0.  So if fanotify gets an event regarding a
large file, the read() will just fail with -EOVERFLOW.

This patch adds O_LARGEFILE to fanotify_init()'s event_f_flags on 64-bit
systems, using the same test as open()/openat()/etc.

Addresses https://bugzilla.redhat.com/show_bug.cgi?id=696821Signed-off-by: Will Woods <wwoods@redhat.com>
Acked-by: Eric Paris <eparis@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

debugobjects warning during netfilter exit:

    ------------[ cut here ]------------
    WARNING: CPU: 6 PID: 4178 at lib/debugobjects.c:260 debug_print_object+0x8d/0xb0()
    ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x20
    Modules linked in:
    CPU: 6 PID: 4178 Comm: kworker/u16:2 Tainted: G        W 3.11.0-next-20130906-sasha #3984
    Workqueue: netns cleanup_net
    Call Trace:
      dump_stack+0x52/0x87
      warn_slowpath_common+0x8c/0xc0
      warn_slowpath_fmt+0x46/0x50
      debug_print_object+0x8d/0xb0
      __debug_check_no_obj_freed+0xa5/0x220
      debug_check_no_obj_freed+0x15/0x20
      kmem_cache_free+0x197/0x340
      kmem_cache_destroy+0x86/0xe0
      nf_conntrack_cleanup_net_list+0x131/0x170
      nf_conntrack_pernet_exit+0x5d/0x70
      ops_exit_list+0x5e/0x70
      cleanup_net+0xfb/0x1c0
      process_one_work+0x338/0x550
      worker_thread+0x215/0x350
      kthread+0xe7/0xf0
      ret_from_fork+0x7c/0xb0

Also during dcookie cleanup:

    WARNING: CPU: 12 PID: 9725 at lib/debugobjects.c:260 debug_print_object+0x8c/0xb0()
    ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x20
    Modules linked in:
    CPU: 12 PID: 9725 Comm: trinity-c141 Not tainted 3.15.0-rc2-next-20140423-sasha-00018-gc4ff6c4 #408
    Call Trace:
      dump_stack (lib/dump_stack.c:52)
      warn_slowpath_common (kernel/panic.c:430)
      warn_slowpath_fmt (kernel/panic.c:445)
      debug_print_object (lib/debugobjects.c:262)
      __debug_check_no_obj_freed (lib/debugobjects.c:697)
      debug_check_no_obj_freed (lib/debugobjects.c:726)
      kmem_cache_free (mm/slub.c:2689 mm/slub.c:2717)
      kmem_cache_destroy (mm/slab_common.c:363)
      dcookie_unregister (fs/dcookies.c:302 fs/dcookies.c:343)
      event_buffer_release (arch/x86/oprofile/../../../drivers/oprofile/event_buffer.c:153)
      __fput (fs/file_table.c:217)
      ____fput (fs/file_table.c:253)
      task_work_run (kernel/task_work.c:125 (discriminator 1))
      do_notify_resume (include/linux/tracehook.h:196 arch/x86/kernel/signal.c:751)
      int_signal (arch/x86/kernel/entry_64.S:807)

Sysfs has a release mechanism.  Use that to release the kmem_cache
structure if CONFIG_SYSFS is enabled.

Only slub is changed - slab currently only supports /proc/slabinfo and
not /sys/kernel/slab/*.  We talked about adding that and someone was
working on it.

[akpm@linux-foundation.org: fix CONFIG_SYSFS=n build]
[akpm@linux-foundation.org: fix CONFIG_SYSFS=n build even more]
Signed-off-by: Christoph Lameter <cl@linux.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Greg KH <greg@kroah.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 0bf1457f ("mm: vmscan: do not swap anon pages
just because free+file is low") because it introduced a regression in
mostly-anonymous workloads, where reclaim would become ineffective and
trap every allocating task in direct reclaim.

The problem is that there is a runaway feedback loop in the scan balance
between file and anon, where the balance tips heavily towards a tiny
thrashing file LRU and anonymous pages are no longer being looked at.
The commit in question removed the safe guard that would detect such
situations and respond with forced anonymous reclaim.

This commit was part of a series to fix premature swapping in loads with
relatively little cache, and while it made a small difference, the cure
is obviously worse than the disease.  Revert it.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@kernel.org>		[3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

autofs needs to be able to see private data dentry flags for its dentrys
that are being created but not yet hashed and for its dentrys that have
been rmdir()ed but not yet freed.  It needs to do this so it can block
processes in these states until a status has been returned to indicate
the given operation is complete.

It does this by keeping two lists, active and expring, of dentrys in
this state and uses ->d_release() to keep them stable while it checks
the reference count to determine if they should be used.

But with the recent lockref changes dentrys being freed sometimes don't
transition to a reference count of 0 before being freed so autofs can
occassionally use a dentry that is invalid which can lead to a panic.
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Dave Jones reports the following crash when find_get_pages_tag() runs
into an exceptional entry:

  kernel BUG at mm/filemap.c:1347!
  RIP: find_get_pages_tag+0x1cb/0x220
  Call Trace:
    find_get_pages_tag+0x36/0x220
    pagevec_lookup_tag+0x21/0x30
    filemap_fdatawait_range+0xbe/0x1e0
    filemap_fdatawait+0x27/0x30
    sync_inodes_sb+0x204/0x2a0
    sync_inodes_one_sb+0x19/0x20
    iterate_supers+0xb2/0x110
    sys_sync+0x44/0xb0
    ia32_do_call+0x13/0x13

  1343                         /*
  1344                          * This function is never used on a shmem/tmpfs
  1345                          * mapping, so a swap entry won't be found here.
  1346                          */
  1347                         BUG();

After commit 0cd6144a ("mm + fs: prepare for non-page entries in
page cache radix trees") this comment and BUG() are out of date because
exceptional entries can now appear in all mappings - as shadows of
recently evicted pages.

However, as Hugh Dickins notes,

  "it is truly surprising for a PAGECACHE_TAG_WRITEBACK (and probably
   any other PAGECACHE_TAG_*) to appear on an exceptional entry.

   I expect it comes down to an occasional race in RCU lookup of the
   radix_tree: lacking absolute synchronization, we might sometimes
   catch an exceptional entry, with the tag which really belongs with
   the unexceptional entry which was there an instant before."

And indeed, not only is the tree walk lockless, the tags are also read
in chunks, one radix tree node at a time.  There is plenty of time for
page reclaim to swoop in and replace a page that was already looked up
as tagged with a shadow entry.

Remove the BUG() and update the comment.  While reviewing all other
lookup sites for whether they properly deal with shadow entries of
evicted pages, update all the comments and fix memcg file charge moving
to not miss shmem/tmpfs swapcache pages.

Fixes: 0cd6144a ("mm + fs: prepare for non-page entries in page cache radix trees")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The compaction freepage scanner implementation in isolate_freepages()
starts by taking the current cc->free_pfn value as the first pfn.  In a
for loop, it scans from this first pfn to the end of the pageblock, and
then subtracts pageblock_nr_pages from the first pfn to obtain the first
pfn for the next for loop iteration.

This means that when cc->free_pfn starts at offset X rather than being
aligned on pageblock boundary, the scanner will start at offset X in all
scanned pageblock, ignoring potentially many free pages.  Currently this
can happen when

 a) zone's end pfn is not pageblock aligned, or

 b) through zone->compact_cached_free_pfn with CONFIG_HOLES_IN_ZONE
    enabled and a hole spanning the beginning of a pageblock

This patch fixes the problem by aligning the initial pfn in
isolate_freepages() to pageblock boundary.  This also permits replacing
the end-of-pageblock alignment within the for loop with a simple
pageblock_nr_pages increment.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Heesub Shin <heesub.shin@samsung.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Acked-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Dongjun Shin <d.j.shin@samsung.com>
Cc: Sunghwan Yun <sunghwan.yun@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sjenning@linux.vnet.ibm.com is no longer a viable entity.
Signed-off-by: Seth Jennings <sjennings@variantweb.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It is possible for "limit - setpoint + 1" to equal zero, after getting
truncated to a 32 bit variable, and resulting in a divide by zero error.

Using the fully 64 bit divide functions avoids this problem.  It also
will cause pos_ratio_polynom() to return the correct value when
(setpoint - limit) exceeds 2^32.

Also uninline pos_ratio_polynom, at Andrew's request.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently, I am seeing the following when I `mount -t hugetlbfs /none
/dev/hugetlbfs`, and then simply do a `ls /dev/hugetlbfs`.  I think it's
related to the fact that hugetlbfs is properly not correctly setting
itself up in this state?:

  Unable to handle kernel paging request for data at address 0x00000031
  Faulting instruction address: 0xc000000000245710
  Oops: Kernel access of bad area, sig: 11 [#1]
  SMP NR_CPUS=2048 NUMA pSeries
  ....

In KVM guests on Power, in a guest not backed by hugepages, we see the
following:

  AnonHugePages:         0 kB
  HugePages_Total:       0
  HugePages_Free:        0
  HugePages_Rsvd:        0
  HugePages_Surp:        0
  Hugepagesize:         64 kB

HPAGE_SHIFT == 0 in this configuration, which indicates that hugepages
are not supported at boot-time, but this is only checked in
hugetlb_init().  Extract the check to a helper function, and use it in a
few relevant places.

This does make hugetlbfs not supported (not registered at all) in this
environment.  I believe this is fine, as there are no valid hugepages
and that won't change at runtime.

[akpm@linux-foundation.org: use pr_info(), per Mel]
[akpm@linux-foundation.org: fix build when HPAGE_SHIFT is undefined]
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

After creating a cache for a memcg we should initialize its sysfs attrs
with the values from its parent.  That's what memcg_propagate_slab_attrs
is for.  Currently it's broken - we clearly muddled root-vs-memcg caches
there.  Let's fix it up.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>