Check if operation is valid before changing any
settings in hardware. Otherwise it results in
changes being made despite it not being a valid
operation.

Fixes: 78eab33b ("net: sparx5: add vlan support")
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function pci_find_capability() in t3_prep_adapter() can fail, so its
return value should be checked.

Fixes: 4d22de3e ("Add support for the latest 1G/10G Chelsio adapter, T3")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sukadev Bhattiprolu says:

====================
ibmvnic: Fix a race in ibmvnic_probe()

If we get a transport (reset) event right after a successful CRQ_INIT
during ibmvnic_probe() but before we set the adapter state to VNIC_PROBED,
we will throw away the reset assuming that the adapter is still in the
probing state. But since the adapter has completed the CRQ_INIT any
subsequent CRQs the we send will be ignored by the vnicserver until
we release/init the CRQ again. This can leave the adapter unconfigured.

While here fix a couple of other bugs that were observed (Patches 1,2,4).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently don't allow queuing resets when adapter is in VNIC_PROBING
state - instead we throw away the reset and return EBUSY. The reasoning
is probably that during ibmvnic_probe() the ibmvnic_adapter itself is
being initialized so performing a reset during this time can lead us to
accessing fields in the ibmvnic_adapter that are not fully initialized.
A review of the code shows that all the adapter state neede to process a
reset is initialized before registering the CRQ so that should no longer
be a concern.

Further the expectation is that if we do get a reset (transport event)
during probe, the do..while() loop in ibmvnic_probe() will handle this
by reinitializing the CRQ.

While that is true to some extent, it is possible that the reset might
occur _after_ the CRQ is registered and CRQ_INIT message was exchanged
but _before_ the adapter state is set to VNIC_PROBED. As mentioned above,
such a reset will be thrown away. While the client assumes that the
adapter is functional, the vnic server will wait for the client to reinit
the adapter. This disconnect between the two leaves the adapter down
needing manual intervention.

Because ibmvnic_probe() has other work to do after initializing the CRQ
(such as registering the netdev at a minimum) and because the reset event
can occur at any instant after the CRQ is initialized, there will always
be a window between initializing the CRQ and considering the adapter
ready for resets (ie state == PROBED).

So rather than discarding resets during this window, allow queueing them
- but only process them after the adapter is fully initialized.

To do this, introduce a new completion state ->probe_done and have the
reset worker thread wait on this before processing resets.

This change brings up two new situations in or just after ibmvnic_probe().
First after one or more resets were queued, we encounter an error and
decide to retry the initialization.  At that point the queued resets are
no longer relevant since we could be talking to a new vnic server. So we
must purge/flush the queued resets before restarting the initialization.
As a side note, since we are still in the probing stage and we have not
registered the netdev, it will not be CHANGE_PARAM reset.

Second this change opens up a potential race between the worker thread
in __ibmvnic_reset(), the tasklet and the ibmvnic_open() due to the
following sequence of events:

	1. Register CRQ
	2. Get transport event before CRQ_INIT completes.
	3. Tasklet schedules reset:
		a) add rwi to list
		b) schedule_work() to start worker thread which runs
		   and waits for ->probe_done.
	4. ibmvnic_probe() decides to retry, purges rwi_list
	5. Re-register crq and this time rest of probe succeeds - register
	   netdev and complete(->probe_done).
	6. Worker thread resumes in __ibmvnic_reset() from 3b.
	7. Worker thread sets ->resetting bit
	8. ibmvnic_open() comes in, notices ->resetting bit, sets state
	   to IBMVNIC_OPEN and returns early expecting worker thread to
	   finish the open.
	9. Worker thread finds rwi_list empty and returns without
	   opening the interface.

If this happens, the ->ndo_open() call is effectively lost and the
interface remains down. To address this, ensure that ->rwi_list is
not empty before setting the ->resetting  bit. See also comments in
__ibmvnic_reset().

Fixes: 6a2fb0e9 ("ibmvnic: driver initialization for kdump/kexec")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clear ->failover_pending flag that may have been set in the previous
pass of registering CRQ. If we don't clear, a subsequent ibmvnic_open()
call would be misled into thinking a failover is pending and assuming
that the reset worker thread would open the adapter. If this pass of
registering the CRQ succeeds (i.e there is no transport event), there
wouldn't be a reset worker thread.

This would leave the adapter unconfigured and require manual intervention
to bring it up during boot.

Fixes: 5a18e1e0 ("ibmvnic: Fix failover case for non-redundant configuration")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently initialize the ->init_done completion/return code fields
before issuing a CRQ_INIT command. But if we get a transport event soon
after registering the CRQ the taskslet may already have recorded the
completion and error code. If we initialize here, we might overwrite/
lose that and end up issuing the CRQ_INIT only to timeout later.

If that timeout happens during probe, we will leave the adapter in the
DOWN state rather than retrying to register/init the CRQ.

Initialize the completion before registering the CRQ so we don't lose
the notification.

Fixes: 032c5e82 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Finish initializing the adapter before registering netdev so state
is consistent.

Fixes: c26eba03 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we get a transport event, set the error and mark the init as
complete so the attempt to send crq-init or login fail sooner
rather than wait for the timeout.

Fixes: bbd669a8 ("ibmvnic: Fix completion structure initialization")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define and use a helper to flush the reset queue.

Fixes: 2770a798 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should initialize ->init_done_rc before calling complete(). Otherwise
the waiting thread may see ->init_done_rc as 0 before we have updated it
and may assume that the CRQ was successful.

Fixes: 6b278c0c ("ibmvnic delay complete()")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a tiny memory leak when flushing the reset work queue.

Fixes: 2770a798 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
1) Fix PMTU for IPv6 if the reported MTU minus the ESP overhead is
   smaller than 1280. From Jiri Bohac.

2) Fix xfrm interface ID and inter address family tunneling when
   migrating xfrm states. From Yan Yan.

3) Add missing xfrm intrerface ID initialization on xfrmi_changelink.
   From Antony Antony.

4) Enforce validity of xfrm offload input flags so that userspace can't
   send undefined flags to the offload driver.
   From Leon Romanovsky.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If I'm not mistaken (and I don't think I am), the way in which the
dcbnl_ops work is that drivers call dcb_ieee_setapp() and this populates
the application table with dynamically allocated struct dcb_app_type
entries that are kept in the module-global dcb_app_list.

However, nobody keeps exact track of these entries, and although
dcb_ieee_delapp() is supposed to remove them, nobody does so when the
interface goes away (example: driver unbinds from device). So the
dcb_app_list will contain lingering entries with an ifindex that no
longer matches any device in dcb_app_lookup().

Reclaim the lost memory by listening for the NETDEV_UNREGISTER event and
flushing the app table entries of interfaces that are now gone.

In fact something like this used to be done as part of the initial
commit (blamed below), but it was done in dcbnl_exit() -> dcb_flushapp(),
essentially at module_exit time. That became dead code after commit
7a6b6f51 ("DCB: fix kconfig option") which essentially merged
"tristate config DCB" and "bool config DCBNL" into a single "bool config
DCB", so net/dcb/dcbnl.c could not be built as a module anymore.

Commit 36b9ad80 ("net/dcb: make dcbnl.c explicitly non-modular")
recognized this and deleted dcbnl_exit() and dcb_flushapp() altogether,
leaving us with the version we have today.

Since flushing application table entries can and should be done as soon
as the netdevice disappears, fundamentally the commit that is to blame
is the one that introduced the design of this API.

Fixes: 9ab933ab ("dcbnl: add appliction tlv handlers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a potential leak issue under following execution sequence :

smc_release  				smc_connect_work
if (sk->sk_state == SMC_INIT)
					send_clc_confirim
	tcp_abort();
					...
					sk.sk_state = SMC_ACTIVE
smc_close_active
switch(sk->sk_state) {
...
case SMC_ACTIVE:
	smc_close_final()
	// then wait peer closed

Unfortunately, tcp_abort() may discard CLC CONFIRM messages that are
still in the tcp send buffer, in which case our connection token cannot
be delivered to the server side, which means that we cannot get a
passive close message at all. Therefore, it is impossible for the to be
disconnected at all.

This patch tries a very simple way to avoid this issue, once the state
has changed to SMC_ACTIVE after tcp_abort(), we can actively abort the
smc connection, considering that the state is SMC_INIT before
tcp_abort(), abandoning the complete disconnection process should not
cause too much problem.

In fact, this problem may exist as long as the CLC CONFIRM message is
not received by the server. Whether a timer should be added after
smc_close_final() needs to be discussed in the future. But even so, this
patch provides a faster release for connection in above case, it should
also be valuable.

Fixes: 39f41f36 ("net/smc: common release code for non-accepted sockets")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In this driver's ->ndo_open() callback, it enables DMA interrupts,
starts the DMA channels, then requests interrupts with request_irq(),
and then finally enables napi.

If RX DMA interrupts are received before napi is enabled, no processing
is done because napi_schedule_prep() will return false.  If the network
has a lot of broadcast/multicast traffic, then the RX ring could fill up
completely before napi is enabled.  When this happens, no further RX
interrupts will be delivered, and the driver will fail to receive any
packets.

Fix this by only enabling DMA interrupts after all other initialization
is complete.

Fixes: 523f11b5 ("net: stmmac: move hardware setup for stmmac_open to new function")
Reported-by: Lars Persson <larper@axis.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xennet_destroy_queues() relies on info->netdev->real_num_tx_queues to
delete queues. Since d7dac083
("net-sysfs: update the queue counts in the unregistration path"),
unregister_netdev() indirectly sets real_num_tx_queues to 0. Those two
facts together means, that xennet_destroy_queues() called from
xennet_remove() cannot do its job, because it's called after
unregister_netdev(). This results in kfree-ing queues that are still
linked in napi, which ultimately crashes:

    BUG: kernel NULL pointer dereference, address: 0000000000000000
    #PF: supervisor read access in kernel mode
    #PF: error_code(0x0000) - not-present page
    PGD 0 P4D 0
    Oops: 0000 [#1] PREEMPT SMP PTI
    CPU: 1 PID: 52 Comm: xenwatch Tainted: G        W         5.16.10-1.32.fc32.qubes.x86_64+ #226
    RIP: 0010:free_netdev+0xa3/0x1a0
    Code: ff 48 89 df e8 2e e9 00 00 48 8b 43 50 48 8b 08 48 8d b8 a0 fe ff ff 48 8d a9 a0 fe ff ff 49 39 c4 75 26 eb 47 e8 ed c1 66 ff <48> 8b 85 60 01 00 00 48 8d 95 60 01 00 00 48 89 ef 48 2d 60 01 00
    RSP: 0000:ffffc90000bcfd00 EFLAGS: 00010286
    RAX: 0000000000000000 RBX: ffff88800edad000 RCX: 0000000000000000
    RDX: 0000000000000001 RSI: ffffc90000bcfc30 RDI: 00000000ffffffff
    RBP: fffffffffffffea0 R08: 0000000000000000 R09: 0000000000000000
    R10: 0000000000000000 R11: 0000000000000001 R12: ffff88800edad050
    R13: ffff8880065f8f88 R14: 0000000000000000 R15: ffff8880066c6680
    FS:  0000000000000000(0000) GS:ffff8880f3300000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 0000000000000000 CR3: 00000000e998c006 CR4: 00000000003706e0
    Call Trace:
     <TASK>
     xennet_remove+0x13d/0x300 [xen_netfront]
     xenbus_dev_remove+0x6d/0xf0
     __device_release_driver+0x17a/0x240
     device_release_driver+0x24/0x30
     bus_remove_device+0xd8/0x140
     device_del+0x18b/0x410
     ? _raw_spin_unlock+0x16/0x30
     ? klist_iter_exit+0x14/0x20
     ? xenbus_dev_request_and_reply+0x80/0x80
     device_unregister+0x13/0x60
     xenbus_dev_changed+0x18e/0x1f0
     xenwatch_thread+0xc0/0x1a0
     ? do_wait_intr_irq+0xa0/0xa0
     kthread+0x16b/0x190
     ? set_kthread_struct+0x40/0x40
     ret_from_fork+0x22/0x30
     </TASK>

Fix this by calling xennet_destroy_queues() from xennet_uninit(),
when real_num_tx_queues is still available. This ensures that queues are
destroyed when real_num_tx_queues is set to 0, regardless of how
unregister_netdev() was called.

Originally reported at
https://github.com/QubesOS/qubes-issues/issues/7257

Fixes: d7dac083 ("net-sysfs: update the queue counts in the unregistration path")
Cc: stable@vger.kernel.org
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Fixes for 5.17

Patch 1 fixes an issue with the SIOCOUTQ ioctl in MPTCP sockets that
have performed a fallback to TCP.

Patch 2 is a selftest fix to correctly remove temp files.

Patch 3 fixes a shift-out-of-bounds issue found by syzkaller.
====================

Link: https://lore.kernel.org/r/20220225005259.318898-1-mathew.j.martineau@linux.intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Syzkaller with UBSAN uncovered a scenario where a large number of
DATA_FIN retransmits caused a shift-out-of-bounds in the DATA_FIN
timeout calculation:

================================================================================
UBSAN: shift-out-of-bounds in net/mptcp/protocol.c:470:29
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 1 PID: 13059 Comm: kworker/1:0 Not tainted 5.17.0-rc2-00630-g5fbf21c90c60 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Workqueue: events mptcp_worker
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
 ubsan_epilogue+0xb/0x5a lib/ubsan.c:151
 __ubsan_handle_shift_out_of_bounds.cold+0xb2/0x20e lib/ubsan.c:330
 mptcp_set_datafin_timeout net/mptcp/protocol.c:470 [inline]
 __mptcp_retrans.cold+0x72/0x77 net/mptcp/protocol.c:2445
 mptcp_worker+0x58a/0xa70 net/mptcp/protocol.c:2528
 process_one_work+0x9df/0x16d0 kernel/workqueue.c:2307
 worker_thread+0x95/0xe10 kernel/workqueue.c:2454
 kthread+0x2f4/0x3b0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
 </TASK>
================================================================================

This change limits the maximum timeout by limiting the size of the
shift, which keeps all intermediate values in-bounds.

Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/259
Fixes: 6477dd39 ("mptcp: Retransmit DATA_FIN")
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After commit 05be5e27 ("selftests: mptcp: add disconnect tests")
the mptcp selftests leave behind a couple of tmp files after
each run. run_tests_disconnect() misnames a few variables used to
track them. Address the issue setting the appropriate global variables

Fixes: 05be5e27 ("selftests: mptcp: add disconnect tests")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The MPTCP SIOCOUTQ implementation is not very accurate in
case of fallback: it only measures the data in the MPTCP-level
write queue, but it does not take in account the subflow
write queue utilization. In case of fallback the first can be
empty, while the latter is not.

The above produces sporadic self-tests issues and can foul
legit user-space application.

Fix the issue additionally querying the subflow in case of fallback.

Fixes: 644807e3 ("mptcp: add SIOCINQ, OUTQ and OUTQNSD ioctls")
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/260Reported-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

 - Fix regression with RFCOMM
 - Fix regression with LE devices using Privacy (RPA)
 - Fix regression with LE devices not waiting proper timeout to
   establish connections
 - Fix race in smp

* tag 'for-net-2022-02-24' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
  Bluetooth: hci_sync: Fix not using conn_timeout
  Bluetooth: hci_sync: Fix hci_update_accept_list_sync
  Bluetooth: assign len after null check
  Bluetooth: Fix bt_skb_sendmmsg not allocating partial chunks
  Bluetooth: fix data races in smp_unregister(), smp_del_chan()
  Bluetooth: hci_core: Fix leaking sent_cmd skb
====================

Link: https://lore.kernel.org/r/20220224210838.197787-1-luiz.dentz@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull pci fixes from Bjorn Helgaas:

 - Fix a merge error that broke PCI device enumeration on mvebu
   platforms, including Turris Omnia (Armada 385) (Pali Rohár)

 - Avoid using ATS on all AMD Navi10 and Navi14 GPUs because some
   VBIOSes don't account for "harvested" (disabled) parts of the chip
   when initializing caches (Alex Deucher)

* tag 'pci-v5.17-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Mark all AMD Navi10 and Navi14 GPU ATS as broken
  PCI: mvebu: Fix device enumeration regression

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf and netfilter.

  Current release - regressions:

   - bpf: fix crash due to out of bounds access into reg2btf_ids

   - mvpp2: always set port pcs ops, avoid null-deref

   - eth: marvell: fix driver load from initrd

   - eth: intel: revert "Fix reset bw limit when DCB enabled with 1 TC"

  Current release - new code bugs:

   - mptcp: fix race in overlapping signal events

  Previous releases - regressions:

   - xen-netback: revert hotplug-status changes causing devices to not
     be configured

   - dsa:
      - avoid call to __dev_set_promiscuity() while rtnl_mutex isn't
        held
      - fix panic when removing unoffloaded port from bridge

   - dsa: microchip: fix bridging with more than two member ports

  Previous releases - always broken:

   - bpf:
      - fix crash due to incorrect copy_map_value when both spin lock
        and timer are present in a single value
      - fix a bpf_timer initialization issue with clang
      - do not try bpf_msg_push_data with len 0
      - add schedule points in batch ops

   - nf_tables:
      - unregister flowtable hooks on netns exit
      - correct flow offload action array size
      - fix a couple of memory leaks

   - vsock: don't check owner in vhost_vsock_stop() while releasing

   - gso: do not skip outer ip header in case of ipip and net_failover

   - smc: use a mutex for locking "struct smc_pnettable"

   - openvswitch: fix setting ipv6 fields causing hw csum failure

   - mptcp: fix race in incoming ADD_ADDR option processing

   - sysfs: add check for netdevice being present to speed_show

   - sched: act_ct: fix flow table lookup after ct clear or switching
     zones

   - eth: intel: fixes for SR-IOV forwarding offloads

   - eth: broadcom: fixes for selftests and error recovery

   - eth: mellanox: flow steering and SR-IOV forwarding fixes

  Misc:

   - make __pskb_pull_tail() & pskb_carve_frag_list() drop_monitor
     friends not report freed skbs as drops

   - force inlining of checksum functions in net/checksum.h"

* tag 'net-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (85 commits)
  net: mv643xx_eth: process retval from of_get_mac_address
  ping: remove pr_err from ping_lookup
  Revert "i40e: Fix reset bw limit when DCB enabled with 1 TC"
  openvswitch: Fix setting ipv6 fields causing hw csum failure
  ipv6: prevent a possible race condition with lifetimes
  net/smc: Use a mutex for locking "struct smc_pnettable"
  bnx2x: fix driver load from initrd
  Revert "xen-netback: Check for hotplug-status existence before watching"
  Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"
  net/mlx5e: Fix VF min/max rate parameters interchange mistake
  net/mlx5e: Add missing increment of count
  net/mlx5e: MPLSoUDP decap, fix check for unsupported matches
  net/mlx5e: Fix MPLSoUDP encap to use MPLS action information
  net/mlx5e: Add feature check for set fec counters
  net/mlx5e: TC, Skip redundant ct clear actions
  net/mlx5e: TC, Reject rules with forward and drop actions
  net/mlx5e: TC, Reject rules with drop and modify hdr action
  net/mlx5e: kTLS, Use CHECKSUM_UNNECESSARY for device-offloaded packets
  net/mlx5e: Fix wrong return value on ioctl EEPROM query failure
  net/mlx5: Fix possible deadlock on rule deletion
  ...

When using hci_le_create_conn_sync it shall wait for the conn_timeout
since the connection complete may take longer than just 2 seconds.

Also fix the masking of HCI_EV_LE_ENHANCED_CONN_COMPLETE and
HCI_EV_LE_CONN_COMPLETE so they are never both set so we can predict
which one the controller will use in case of HCI_OP_LE_CREATE_CONN.

Fixes: 6cd29ec6 ("Bluetooth: hci_sync: Wait for proper events when connecting LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

hci_update_accept_list_sync is returning the filter based on the error
but that gets overwritten by hci_le_set_addr_resolution_enable_sync
return instead of using the actual result of the likes of
hci_le_add_accept_list_sync which was intended.

Fixes: ad383c2c ("Bluetooth: hci_sync: Enable advertising when LL privacy is enabled")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

len should be assigned after a null check
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Since bt_skb_sendmmsg can be used with the likes of SOCK_STREAM it
shall return the partial chunks it could allocate instead of freeing
everything as otherwise it can cause problems like bellow.

Fixes: 81be03e0 ("Bluetooth: RFCOMM: Replace use of memcpy_from_msg with bt_skb_sendmmsg")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/r/d7206e12-1b99-c3be-84f4-df22af427ef5@molgen.mpg.de
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215594Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> (Nokia N9 (MeeGo/Harmattan)
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Previous commit e0448092 ("Bluetooth: defer cleanup of resources
in hci_unregister_dev()") defers all destructive actions to
hci_release_dev() to prevent cocurrent problems like NPD, UAF.

However, there are still some exceptions that are ignored.

The smp_unregister() in hci_dev_close_sync() (previously in
hci_dev_do_close) will release resources like the sensitive channel
and the smp_dev objects. Consider the situations the device is detaching
or power down while the kernel is still operating on it, the following
data race could take place.

thread-A  hci_dev_close_sync  | thread-B  read_local_oob_ext_data
                              |
hci_dev_unlock()              |
...                           | hci_dev_lock()
if (hdev->smp_data)           |
  chan = hdev->smp_data       |
                              | chan = hdev->smp_data (3)
                              |
  hdev->smp_data = NULL (1)   | if (!chan || !chan->data) (4)
  ...                         |
  smp = chan->data            | smp = chan->data
  if (smp)                    |
    chan->data = NULL (2)     |
    ...                       |
    kfree_sensitive(smp)      |
                              | // dereference smp trigger UFA

That is, the objects hdev->smp_data and chan->data both suffer from the
data races. In a preempt-enable kernel, the above schedule (when (3) is
before (1) and (4) is before (2)) leads to UAF bugs. It can be
reproduced in the latest kernel and below is part of the report:

[   49.097146] ================================================================
[   49.097611] BUG: KASAN: use-after-free in smp_generate_oob+0x2dd/0x570
[   49.097611] Read of size 8 at addr ffff888006528360 by task generate_oob/155
[   49.097611]
[   49.097611] Call Trace:
[   49.097611]  <TASK>
[   49.097611]  dump_stack_lvl+0x34/0x44
[   49.097611]  print_address_description.constprop.0+0x1f/0x150
[   49.097611]  ? smp_generate_oob+0x2dd/0x570
[   49.097611]  ? smp_generate_oob+0x2dd/0x570
[   49.097611]  kasan_report.cold+0x7f/0x11b
[   49.097611]  ? smp_generate_oob+0x2dd/0x570
[   49.097611]  smp_generate_oob+0x2dd/0x570
[   49.097611]  read_local_oob_ext_data+0x689/0xc30
[   49.097611]  ? hci_event_packet+0xc80/0xc80
[   49.097611]  ? sysvec_apic_timer_interrupt+0x9b/0xc0
[   49.097611]  ? asm_sysvec_apic_timer_interrupt+0x12/0x20
[   49.097611]  ? mgmt_init_hdev+0x1c/0x240
[   49.097611]  ? mgmt_init_hdev+0x28/0x240
[   49.097611]  hci_sock_sendmsg+0x1880/0x1e70
[   49.097611]  ? create_monitor_event+0x890/0x890
[   49.097611]  ? create_monitor_event+0x890/0x890
[   49.097611]  sock_sendmsg+0xdf/0x110
[   49.097611]  __sys_sendto+0x19e/0x270
[   49.097611]  ? __ia32_sys_getpeername+0xa0/0xa0
[   49.097611]  ? kernel_fpu_begin_mask+0x1c0/0x1c0
[   49.097611]  __x64_sys_sendto+0xd8/0x1b0
[   49.097611]  ? syscall_exit_to_user_mode+0x1d/0x40
[   49.097611]  do_syscall_64+0x3b/0x90
[   49.097611]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[   49.097611] RIP: 0033:0x7f5a59f51f64
...
[   49.097611] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5a59f51f64
[   49.097611] RDX: 0000000000000007 RSI: 00007f5a59d6ac70 RDI: 0000000000000006
[   49.097611] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[   49.097611] R10: 0000000000000040 R11: 0000000000000246 R12: 00007ffec26916ee
[   49.097611] R13: 00007ffec26916ef R14: 00007f5a59d6afc0 R15: 00007f5a59d6b700

To solve these data races, this patch places the smp_unregister()
function in the protected area by the hci_dev_lock(). That is, the
smp_unregister() function can not be concurrently executed when
operating functions (most of them are mgmt operations in mgmt.c) hold
the device lock.

This patch is tested with kernel LOCK DEBUGGING enabled. The price from
the extended holding time of the device lock is supposed to be low as the
smp_unregister() function is fairly short and efficient.
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

sent_cmd memory is not freed before freeing hci_dev causing it to leak
it contents.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Pull block fixes from Jens Axboe:

 - NVMe pull request:
    - send H2CData PDUs based on MAXH2CDATA (Varun Prakash)
    - fix passthrough to namespaces with unsupported features (Christoph
      Hellwig)

 - Clear iocb->private at poll completion (Stefano)

* tag 'block-5.17-2022-02-24' of git://git.kernel.dk/linux-block:
  nvme-tcp: send H2CData PDUs based on MAXH2CDATA
  nvme: also mark passthrough-only namespaces ready in nvme_update_ns_info
  nvme: don't return an error from nvme_configure_metadata
  block: clear iocb->private in blkdev_bio_end_io_async()

Pull io_uring fixes from Jens Axboe:

 - Add a conditional schedule point in io_add_buffers() (Eric)

 - Fix for a quiesce speedup merged in this release (Dylan)

 - Don't convert to jiffies for event timeout waiting, it's way too
   coarse when we accept a timespec as input (me)

* tag 'io_uring-5.17-2022-02-23' of git://git.kernel.dk/linux-block:
  io_uring: disallow modification of rsrc_data during quiesce
  io_uring: don't convert to jiffies for waiting on timeouts
  io_uring: add a schedule point in io_add_buffers()

Merge tag 'platform-drivers-x86-v5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull more x86 platform driver fixes from Hans de Goede:
 "Two more fixes:

   - Fix suspend/resume regression on AMD Cezanne APUs in >= 5.16

   - Fix Microsoft Surface 3 battery readings"

* tag 'platform-drivers-x86-v5.17-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  surface: surface3_power: Fix battery readings on batteries without a serial number
  platform/x86: amd-pmc: Set QOS during suspend on CZN w/ timer wakeup

Obtaining a MAC address may be deferred in cases when the MAC is stored
in an NVMEM block, for example, and it may not be ready upon the first
retrieval attempt and return EPROBE_DEFER.

It is also possible that a port that does not rely on NVMEM has been
already created when getting the defer request. Thus, also the resources
allocated previously must be freed when doing a roll-back.

Fixes: 76723bca ("net: mv643xx_eth: add DT parsing support")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220223142337.41757-1-maukka@ext.kapsi.fiSigned-off-by: Jakub Kicinski <kuba@kernel.org>

As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().

Fixes: 35a79e64 ("ping: fix the dif and sdif check in ping_lookup")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/1ef3f2fcd31bd681a193b1fcf235eee1603819bd.1645674068.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Revert of a patch that instead of fixing a AQ error when trying
to reset BW limit introduced several regressions related to
creation and managing TC. Currently there are errors when creating
a TC on both PF and VF.

Error log:
[17428.783095] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783107] i40e 0000:3b:00.1: Failed configuring TC map 0 for VSI 391
[17428.783254] i40e 0000:3b:00.1: AQ command Config VSI BW allocation per TC failed = 14
[17428.783259] i40e 0000:3b:00.1: Unable to  configure TC map 0 for VSI 391

This reverts commit 3d250466.

Fixes: 3d250466 (i40e: Fix reset bw limit when DCB enabled with 1 TC)
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220223175347.1690692-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.

Fix this by updating skb->csum if available.

Trace resulted by ipv6 ttl dec and then sending packet
to conntrack [actions: set(ipv6(hlimit=63)),ct(zone=99)]:
[295241.900063] s_pf0vf2: hw csum failure
[295241.923191] Call Trace:
[295241.925728]  <IRQ>
[295241.927836]  dump_stack+0x5c/0x80
[295241.931240]  __skb_checksum_complete+0xac/0xc0
[295241.935778]  nf_conntrack_tcp_packet+0x398/0xba0 [nf_conntrack]
[295241.953030]  nf_conntrack_in+0x498/0x5e0 [nf_conntrack]
[295241.958344]  __ovs_ct_lookup+0xac/0x860 [openvswitch]
[295241.968532]  ovs_ct_execute+0x4a7/0x7c0 [openvswitch]
[295241.979167]  do_execute_actions+0x54a/0xaa0 [openvswitch]
[295242.001482]  ovs_execute_actions+0x48/0x100 [openvswitch]
[295242.006966]  ovs_dp_process_packet+0x96/0x1d0 [openvswitch]
[295242.012626]  ovs_vport_receive+0x6c/0xc0 [openvswitch]
[295242.028763]  netdev_frame_hook+0xc0/0x180 [openvswitch]
[295242.034074]  __netif_receive_skb_core+0x2ca/0xcb0
[295242.047498]  netif_receive_skb_internal+0x3e/0xc0
[295242.052291]  napi_gro_receive+0xba/0xe0
[295242.056231]  mlx5e_handle_rx_cqe_mpwrq_rep+0x12b/0x250 [mlx5_core]
[295242.062513]  mlx5e_poll_rx_cq+0xa0f/0xa30 [mlx5_core]
[295242.067669]  mlx5e_napi_poll+0xe1/0x6b0 [mlx5_core]
[295242.077958]  net_rx_action+0x149/0x3b0
[295242.086762]  __do_softirq+0xd7/0x2d6
[295242.090427]  irq_exit+0xf7/0x100
[295242.093748]  do_IRQ+0x7f/0xd0
[295242.096806]  common_interrupt+0xf/0xf
[295242.100559]  </IRQ>
[295242.102750] RIP: 0033:0x7f9022e88cbd
[295242.125246] RSP: 002b:00007f9022282b20 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffda
[295242.132900] RAX: 0000000000000005 RBX: 0000000000000010 RCX: 0000000000000000
[295242.140120] RDX: 00007f9022282ba8 RSI: 00007f9022282a30 RDI: 00007f9014005c30
[295242.147337] RBP: 00007f9014014d60 R08: 0000000000000020 R09: 00007f90254a8340
[295242.154557] R10: 00007f9022282a28 R11: 0000000000000246 R12: 0000000000000000
[295242.161775] R13: 00007f902308c000 R14: 000000000000002b R15: 00007f9022b71f40

Fixes: 3fdbd1ce ("openvswitch: add ipv6 'set' action")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Link: https://lore.kernel.org/r/20220223163416.24096-1-paulb@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Niels Dossche <niels.dossche@ugent.be>
Link: https://lore.kernel.org/r/20220223131954.6570-1-niels.dossche@ugent.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

smc_pnetid_by_table_ib() uses read_lock() and then it calls smc_pnet_apply_ib()
which, in turn, calls mutex_lock(&smc_ib_devices.mutex).

read_lock() disables preemption. Therefore, the code acquires a mutex while in
atomic context and it leads to a SAC bug.

Fix this bug by replacing the rwlock with a mutex.

Reported-and-tested-by: syzbot+4f322a6d84e991c38775@syzkaller.appspotmail.com
Fixes: 64e28b52 ("net/smc: add pnet table namespace support")
Confirmed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20220223100252.22562-1-fmdefrancesco@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Commit b7a49f73 ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.

Fixes: b7a49f73 ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 2afeec08.

The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).

This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.

More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#uSigned-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Michael Brown <mbrown@fensystems.co.uk>
Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>