When PCI error is detected, in some architectures (like PowerPC) a slot
reset is performed - the driver's error handlers are in charge of "disable"
device before the reset, and re-enable it after a successful slot reset.

There are two cases though that another path is taken on the code: if the
slot reset is not successful or if too many errors already happened in the
specific adapter (meaning that possibly the device is experiencing a HW
failure that slot reset is not able to solve), the core PCI error mechanism
(called EEH in PowerPC) will remove the adapter from the system, since it
will consider this as a permanent failure on device. In this case, a path
is taken that leads to bnx2x_chip_cleanup() calling bnx2x_reset_hw(), which
then tries to perform a HW reset on chip. This reset won't succeed since
the HW is in a fault state, which can be seen by multiple messages on
kernel log like below:

	bnx2x: [bnx2x_issue_dmae_with_comp:552(eth1)]DMAE timeout!
	bnx2x: [bnx2x_write_dmae:600(eth1)]DMAE returned failure -1

After some time, the PCI error mechanism gives up on waiting the driver's
correct removal procedure and forcibly remove the adapter from the system.
We can see soft lockup while core PCI error mechanism is waiting for driver
to accomplish the right removal process.

This patch adds a verification to avoid a chip reset whenever the function
is in PCI error state - since this case is only reached when we have a
device being removed because of a permanent failure, the HW chip reset is
not expected to work fine neither is necessary.

Also, as a minor improvement in error path, we avoid the MCP information dump
in case of non-recoverable PCI error (when adapter is about to be removed),
since it will certainly fail.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original codes depend on that the function parameters are evaluated from
left to right. But the parameter's evaluation order is not defined in C
standard actually.

When flow_keys_have_l4(&keys) is invoked before ___skb_get_hash(skb, &keys,
hashrnd) with some compilers or environment, the keys passed to
flow_keys_have_l4 is not initialized.

Fixes: 6db61d79 ("flow_dissector: Ignore flow dissector return value from ___skb_get_hash")
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung noticed that on the first TFO server data packet sent after
the (TFO) handshake, the server echoed the TCP timestamp value in the
SYN/data instead of the timestamp value in the final ACK of the
handshake. This problem did not happen on regular opens.

The tcp_replace_ts_recent() logic that decides whether to remember an
incoming TS value needs tp->rcv_wup to hold the latest receive
sequence number that we have ACKed (latest tp->rcv_nxt we have
ACKed). This commit fixes this issue by ensuring that a TFO server
properly updates tp->rcv_wup to match tp->rcv_nxt at the time it sends
a SYN/ACK for the SYN/data.
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Fixes: 168a8f58 ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: David S. Miller <davem@davemloft.net>

pskb_may_pull may fail due to various reasons (e.g. alloc failure), but the
skb isn't changed/dropped and processing continues so we shouldn't
increment tx_dropped.

CC: Kyeyoon Park <kyeyoonp@codeaurora.org>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Fixes: 95850116 ("bridge: Add support for IEEE 802.11 Proxy ARP")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All changes are notified, but the initial state was missing.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'default' value was not advertised.

Fixes: f3a1bfb1 ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
net: thunderx: Fixes for TSO offload issues

This patch series fixes couple of issues w.r.t HW TSO offload
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On ThunderX 88xx pass 2.x chips when TSO is offloaded to HW,
HW posts a CQE for every TSO segment transmitted. Current code
does handles this, but is prone to issues when segment sizes are
small resulting in SW processing too many CQEs and also at times
frees a SKB which is not yet transmitted.

This patch handles the errata in a different way and eliminates issues
with earlier approach, TSO packet is submitted to HW with post_cqe=0,
so that no CQE is posted upon completion of transmission of TSO packet
but a additional HDR + IMMEDIATE descriptors are added to SQ due to
which a CQE is posted and will have required info to be used while
cleanup in napi. This way only one CQE is posted for a TSO packet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a issue in HW where-in while sending GSO sized pkts
as part of TSO, if pkt len falls below configured min packet
size i.e 60, NIC will zero PAD packet and also updates IP total length.
Hence set this value to lessthan min pkt size of MAC + IP + TCP
headers, BGX will anyway do the padding to transmit 64 byte pkt
including FCS.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If DCB is configured on the link partner switch with an
unsupported traffic class configuration (e.g. non-contiguous TCs),
the driver is flagging DCB as disabled.  But, for future DCB
LLDPDUs, the driver was checking if the interface was DCB capable
instead of enabled.  This was causing a kernel panic when LLDP
was enabled/disabled on the link partner switch.

This patch corrects the situation by having the LLDP event handler
check the correct flag in the pf structure.  It also cleans up the
setting and clearing of the enabled flag for other checks.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.8

ath9k

* fix regression in client mode beacon configuration
* fix a station pointer which resulted in spurious crashes

mwifiex

* fix large amsdu packets causing firmware hang

brcmfmac

* fix deadlock when removing interface
* fix use of mutex in atomic context
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In a dual bearer configuration, if the second tipc link becomes
active while the first link still has pending nametable "bulk"
updates, it randomly leads to reset of the second link.

When a link is established, the function named_distribute(),
fills the skb based on node mtu (allows room for TUNNEL_PROTOCOL)
with NAME_DISTRIBUTOR message for each PUBLICATION.
However, the function named_distribute() allocates the buffer by
increasing the node mtu by INT_H_SIZE (to insert NAME_DISTRIBUTOR).
This consumes the space allocated for TUNNEL_PROTOCOL.

When establishing the second link, the link shall tunnel all the
messages in the first link queue including the "bulk" update.
As size of the NAME_DISTRIBUTOR messages while tunnelling, exceeds
the link mtu the transmission fails (-EMSGSIZE).

Thus, the synch point based on the message count of the tunnel
packets is never reached leading to link timeout.

In this commit, we adjust the size of name distributor message so that
they can be tunnelled.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent commit 087d7a8c "tg3: Fix for diasllow rx coalescing
time to be 0" disallow to set Rx coalescing time to be 0 as this stops
generating interrupts for the incoming packets. I found the zero
Tx coalescing time stops generating interrupts for outgoing packets
as well and fires Tx watchdog later. To avoid this, don't allow to set
Tx coalescing time to 0 and also remove subsequent checks that become
senseless.

Cc: satish.baddipadige@broadcom.com
Cc: siva.kallam@broadcom.com
Cc: michael.chan@broadcom.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1230:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1192:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset

 Use kzalloc rather than kmalloc followed by memset with 0

 This considers some simple cases that are common and easy to validate
 Note in particular that there are no ...s in the rule, so all of the
 matched code has to be contiguous

Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci

CC: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: couple of fixes

Couple of fixes from Ido and myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When a VLAN is added on a bridge port we should use the existing unicast
flood configuration of the port instead of assuming it's enabled.

Fixes: 0293038e ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 14d39461 ("mlxsw: spectrum: Use per-FID struct for the
VLAN-aware bridge") I added a per-FID struct, which member ports can
take a reference on upon VLAN membership configuration.

However, sometimes only the VLAN flags (e.g. egress untagged) are
toggled without changing the VLAN membership. In these cases we
shouldn't take another reference on the FID.

Fixes: 14d39461 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the notifier is registered for every asic instance, however the
same block. Fix this by moving the registration to module init.

Fixes: c723c735 ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add forgotten notifier unregister.

Fixes: 99724c18 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Originally, I expected that there would be needed to call update
operation in case RALUE record action is changed. However, that is not
needed since write operation takes care of that nicely. Remove prepared
construct and always call the write operation.

Fixes: 61c503f9 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mlxsw we squash tables 254 and 255 together into HW. Kernel adds/dels
/32 ip to/from both 254 and 255. On del path, that causes the same
prefix being removed twice. Fix this by introducing reference counting
for private mlxsw fib entries. That required a bit of code reshuffle.
Also put dev into fib entry key so the same prefix could be represented
once per every router interface.

Fixes: 61c503f9 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
qed*: dcbx fix series.

The series contains several small fixes for qed* dcbx module.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch takes care of clearing the uninitialized buffer before using it.
1. pfc pri-enable bitmap need to be cleared before setting the requested
   enable bits. Without this, the un-touched values will be merged with
   requested values and sent to MFW.
2. The data in app-entry field need to be cleared before using it.
3. Clear the output data buffer used in qed_dcbx_query_params().
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Management firmware requires the selection-field (SF) to be set for
configuring the application/protocol entry in IEEE mode. Without this
setting, the app entry will be configured incorrectly in MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry reported a double free on kcm socket, which could
be easily reproduced by:

	#include <unistd.h>
	#include <sys/syscall.h>

	int main()
	{
	  int fd = syscall(SYS_socket, 0x29ul, 0x5ul, 0x0ul, 0, 0, 0);
	  syscall(SYS_ioctl, fd, 0x89e2ul, 0x20a98000ul, 0, 0, 0);
	  return 0;
	}

This is because on the error path, after we install
the new socket file, we call sock_release() to clean
up the socket, which leaves the fd pointing to a freed
socket. Fix this by calling sys_close() on that fd
directly.

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sean Wang says:

====================
net: ethernet: mediatek: a couple of fixes

a couple of fixes come out from integrating with linux-4.8 rc1
they all are verified and workable on linux-4.8 rc1

Changes since v1:
- usage of loops to work out if all required clock are ready instead
of tedious coding
- remove redundant pinctrl setup that is already done by core driver
thanks for careful and patient reviewing by Andrew Lunn
- splitting distinct changes into the separate patches
- change variable naming from err to ret for readable coding

Changes since v2:
- restore to original clock disabling sequence that is changed
accidentally in the last version
- refine the commit log that would cause misunderstanding what has
been done in the changes
- refine the commit log that would cause footnote losing due to
improper delimiter use

Changes since v3:
- fix git rejects caused by mixing a change from net-next, so
remake the patch set based on the current net branch again.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Return -ENODEV if the MDIO bus is disabled in the device tree.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

a lot of parts in the driver uses devm_* APIs to gain benefits from the
device resource management, so devm_mdiobus_alloc is also used instead
of mdiobus_alloc to have more elegant code flow.

Using common code provided by the devm_* helps to
1) have simplified the code flow as [1] says
2) decrease the risk of incorrect error handling by human
3) only a few drivers used it since it was proposed on linux 3.16,
so just hope to promote for this.

Ref:
[1] https://patchwork.ozlabs.org/patch/344093/Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the missing of_node_put() after finishing the usage
of of_get_child_by_name.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

mtk_stop() must be called to stop for freeing DMA
resources acquired and restoring state changed by mtk_open()
firstly when module removal.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

original mdio_cleanup is not in the symmetric place against where
mdio_init is, so relocate mdio_cleanup to the right one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

these irqs are not used for shared irq and disabled during ethernet stops.
irq requested by devm_request_irq is safe to be freed automatically on
driver detach.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

use skb_free_frag() instead of legacy put_page()
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) If the return value of devm_clk_get is EPROBE_DEFER, we should
defer probing the driver. The change is verified and works based
on 4.8-rc1 staying with the latest clk-next code for MT7623.
2) Changing with the usage of loops to work out if all clocks
required are fine
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

which net device the SKB is complete for depends on the forward port
on txd4 on the corresponding TX descriptor, but the information isn't
set up well in case of  SKB fragments that would lead to watchdog timeout
from the upper layer, so fix it up.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit bc8c20ac ("bridge: multicast: treat igmpv3 report with
INCLUDE and no sources as a leave") seems to have accidentally reverted
commit 47cc84ce ("bridge: fix parsing of MLDv2 reports"). This
commit brings back a change to br_ip6_multicast_mld2_report() where
parsing of MLDv2 reports stops when the first group is successfully
added to the MDB cache.

Fixes: bc8c20ac ("bridge: multicast: treat igmpv3 report with INCLUDE and no sources as a leave")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Allow nf_tables reject expression from input, forward and output hooks,
   since only there the routing information is available, otherwise we crash.

2) Fix unsafe list iteration when flushing timeout and accouting objects.

3) Fix refcount leak on timeout policy parsing failure.

4) Unlink timeout object for unconfirmed conntracks too

5) Missing validation of pkttype mangling from bridge family.

6) Fix refcount leak on ebtables on second lookup for the specific
   bridge match extension, this patch from Sabrina Dubroca.

7) Remove unnecessary ip_hdr() in nf_tables_netdev family.

Patches from 1-5 and 7 from Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Three little fixes:
 * revert a recent wext patch, which Ben Hutchings noticed was
   wrong, and it turns out not to be necessary for any driver

 * fix an infinite loop that can occur under certain conditions
   in mac80211's TDLS code (depending on regulatory information)

 * add a cfg80211_get_station() static inline when cfg80211 isn't
   built, to allow other modules to not have to depend on it for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>