Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Set the Latency Tolerance Reporting (LTR) values for the "PCIe-like"
GbE MAC in the Lynx Point PCH based on Rx buffer size and link speed
when link is up (which must not exceed the maximum latency supported
by the platform), otherwise specify there is no LTR requirement.
Unlike true-PCIe devices which set the LTR maximum snoop/no-snoop
latencies in the LTR Extended Capability Structure in the PCIe Extended
Capability register set, on this device LTR is set by writing the
equivalent snoop/no-snoop latencies in the LTRV register in the MAC and
set the SEND bit to send an Intel On-chip System Fabric sideband (IOSF-SB)
message to the PMC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Now that IEEE802.3az-2010 Energy Efficient Ethernet has been approved as
standard (September 2010) and the driver can enable and disable it via
ethtool, enable the feature by default on parts which support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Devices supported by the driver which support EEE (currently 82579, I217
and I218) are advertising EEE capabilities during auto-negotiation even
when EEE has been disabled.  In addition to not acting as expected, this
also caused the EEE status reported by 'ethtool --show-eee' to be wrong
when two of these devices are connected back-to-back and EEE is disabled
on one.  In addition to fixing this issue, the ability for the user to
specify which speeds (100 or 1000 full-duplex) to advertise EEE support
has been added.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the MAC and PHY are in two different modes (different power levels
and interconnect speeds), it could take a long time before a PHY register
access timed out using the existing MAC-PHY interconnect configuration
coded into the driver for ICH- and PCH-based LOMs.  Introduce an I217/I218-
specific .setup_physical_interface operation which does not override the
interconnect configuration in the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When the LEDs are driven by cathode, the bit logic is reversed.  Use the
LED Invert bit to invert the logic.  Cleanup use of a magic number and
change the for loop increment to reduce the number of shifts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Two 82579 LOMs connected via a 10Mb hub experience extraordinarily low
performance.  This is because 82579 is excessively aggressive on transmit
at 10Mb half-duplex and will not provide sufficient time for the link
partner to transmit.  When the link partner is also 82579, the result is a
lot of collisions (and corresponding re-transmits) that cause the poor
performance. To work-around this issue, significantly increase the IPG in
the MAC to allow enough gap for the link partner to transmit and reduce the
Rx latency in the analog PHY to 0 to reduce the number of collisions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

PHY reads/writes via the MDIC register could potentially return results
from a previous PHY register access.  If that happens, the offset in the
returned results will be that of the previous access and if that is
different from the expected offset, log a debug message and error out.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move mutex initialization by allocation of the mailbox it protects.

introduced in commit 1d6f3cd8 'bnx2x: Prevent VF race'
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tokenring support was deleted in v3.5. One last holdout of the macro
CONFIG_TR escaped that fate. Until now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 40893fd0(net: switch to use skb_probe_transport_header())
involes a new error accidently. When NET_SKBUFF_DATA_USES_OFFSE is
not enabled, below compile error happens:

  CC      net/packet/af_packet.o
  net/packet/af_packet.c: In function ‘packet_sendmsg_spkt’:
  net/packet/af_packet.c:1516:2: error: implicit declaration of function ‘skb_probe_transport_header’ [-Werror=implicit-function-declaration]
  cc1: some warnings being treated as errors
  make[2]: *** [net/packet/af_packet.o] Error 1
  make[1]: *** [net/packet] Error 2
  make: *** [net] Error 2

As it seems skb_probe_transport_header() is not related to
NET_SKBUFF_DATA_USES_OFFSE, we should move the definition of
skb_probe_transport_header() out of scope of
NET_SKBUFF_DATA_USES_OFFSE macro.

Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

yam_open has a redundant null check on null,  it will
never be called with dev == NULL. Remove this redundant check.
This also cleans up a smatch warning:

drivers/net/hamradio/yam.c:869 yam_open() warn: variable
  dereferenced before check 'dev' (see line 867)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	include/net/ipip.h

The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

===================
this is a pull-request for net-next/master. It consists of three
patches by Lars-Peter Clausen to clean up the mcp251x spi-can driver,
two patches from Ludovic Desroches to bring device tree support to the
at91_can driver and a patch by me to fix a sparse warning in the
blackfin driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of fixed speed set up for a NIC (e.g. ethtool -s eth0 autoneg off speed
100 duplex full) with an ethernet cable plugged off, the mentioned algorithm
slows down a NIC speed, so further cable hook-up leads to nonoperable link state.
Signed-off-by: Kirill Kapranov <kapranoff@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the protection of netns_frags.nqueues updates under the LRU_lock,
instead of the write lock.  As they are located on the same cacheline,
and this is also needed when transitioning to use per hash bucket locking.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LRU list is protected by its own lock, since commit 3ef0eb0d
(net: frag, move LRU list maintenance outside of rwlock), and
no-longer by a read_lock.

This makes it possible, to remove the inet_frag_queue, which is about
to be "evicted", from the LRU list head.  This avoids the problem, of
several CPUs grabbing the same frag queue.

Note, cannot remove the inet_frag_lru_del() call in fq_unlink()
called by inet_frag_kill(), because inet_frag_kill() is also used in
other situations.  Thus, we use list_del_init() to allow this
double list_del to work.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a native function to dump hex buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In kernel we have fast and pretty implementation of the isxdigit() function.
Let's use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make few alignments, comment fixes and debug messages.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add full support for "ethtool -m" command.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mail box containing the Vf-Pf messages is susceptible
to a race - it's possible for 2 flows to try and write commands,
causing one to override the other's message.
Use a mutex to synchronize the access, preventing said race.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Outer vlan removal in VF queues was made according to the VF's
multi-function mode (which is never set).
Instead, the PF's multi-function mode should be used to determine
if outer vlan removal is needed.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After a VF performs load/unload its statistics become corrupt -
we now zero the statistics structures upon a VF device load.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ARI forwarding flag is missing from the PCI bridge, remove SR-IOV
support instead of failing the probe process.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 7fa6f34 "AER revised" erroneously inserted an error-flow
in which a semaphore is released even though the attempt to take it
has failed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch to use the new help skb_probe_transport_header() to do the l4 header
probing for untrusted sources. For packets with partial csum, the header should
already been set by skb_partial_csum_set().

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes, we need probe and set the transport header for packets (e.g from
untrusted source). This patch introduces a new helper
skb_probe_transport_header() which tries to probe and set the l4 header through
skb_flow_dissect(), if not just set the transport header to the hint passed by
caller.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For untrusted packets with partial checksum, we need to set the transport header
for precise packet length estimation. We can just let skb_pratial_csum_set() to
do this to avoid extra call to skb_flow_dissect() and simplify the caller.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a number of sparse warnings like:
  warning: incorrect type in argument 2 (different address spaces)
    expected void volatile [noderef] <asn:2>*addr
    got unsigned int *<noident>

  warning: Using plain integer as NULL pointer

Additionally this fixes a warning from checkpatch.pl like:
  WARNING: sizeof pch_param.station should be sizeof(pch_param.station)
Signed-off-by: Sahara <keun-o.park@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull IOMMU fixes from Joerg Roedel:
 "Here are some fixes which have collected since Linux v3.9-rc1.

  The most important one fixes a long-standing regressen which make
  re-hotplugged devices unusable when AMD IOMMU is used.

  The other patches fix build issues (build regression on OMAP and a
  section mismatch).  One patch just removes a duplicate header include."

* tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Make sure dma_ops are set for hotplug devices
  x86, io_apic: remove duplicated include from irq_remapping.c
  iommu: OMAP: build only on OMAP2+
  amd_iommu_init: remove __init from amd_iommu_erratum_746_workaround

Commit 06ae43f3 ("Don't bother with redoing rw_verify_area() from
default_file_splice_from()") lost the checks to test existence of the
write/aio_write methods.  My apologies ;-/

Eventually, we want that in fs/splice.c side of things (no point
repeating it for every buffer, after all), but for now this is the
obvious minimal fix.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes the following sparse warning:

drivers/net/can/bfin_can.c:415:13: warning: symbol 'bfin_can_interrupt' was not declared. Should it be static?
drivers/net/can/bfin_can.c:507:19: warning: symbol 'alloc_bfin_candev' was not declared. Should it be static?
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register() so
we can drop the manual assignment.

The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
	.driver = {
-		.bus = &spi_bus_type,
	},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

SAMA5D3 devices also embed CAN feature. Moreover if we want to produce a single
kernel image it is not useful to be too restrictive.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add device tree support.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

There is a bug introduced with commit 27c2127 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.

Cc: stable@vger.kernel.org
Reported-by: Andreas Degert <andreas.degert@googlemail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>

Signed-off-by: Tony Cheneau <tony.cheneau@amnesiak.org>
Signed-off-by: David S. Miller <davem@davemloft.net>