The cited commit started to reuse function mlx5e_update_ndo_stats() for
the representors as well.
However, the function is hard-coded to work on mlx5e_nic_stats_grps only.
Due to this issue, the representors statistics were not updated in the
output of "ip -s".

Fix it to work with the correct group by extracting it from the caller's
profile.

Also, while at it and since this function became generic, move it to
en_stats.c and rename it accordingly.

Fixes: 8a236b15 ("net/mlx5e: Convert rep stats to mlx5e_stats_grp-based infra")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the FW does not generate events for counters other than error
counters. Unlike ".get_ethtool_stats", ".ndo_get_stats64" (which ip -s
uses) might run in atomic context, while the FW interface is non atomic.
Thus, 'ip' is not allowed to issue FW commands, so it will only display
cached counters in the driver.

Add a SW counter (mcast_packets) in the driver to count rx multicast
packets. The counter also counts broadcast packets, as we consider it a
special case of multicast.
Use the counter value when calling "ip -s"/"ifconfig".

Fixes: f62b8bb8 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The field mask value is provided in network byte order and has to
be converted to host byte order before calculating pedit mask
first bit.

Fixes: 88f30bbc ("net/mlx5e: Bit sized fields rewrite support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The cited commit creates peer miss group during switchdev mode
initialization in order to handle miss packets correctly while in VF
LAG mode. This is done regardless of FW support of such groups which
could cause rules setups failure later on.

Fix by adding FW capability check before creating peer groups/rule.

Fixes: ac004b83 ("net/mlx5e: E-Switch, Add peer miss rules")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add missing mapping remove call when removing ct rule,
as the mapping was allocated when ct rule was adding with ct_label.
Also there is a missing mapping remove call in error flow.

Fixes: 54b154ec ("net/mlx5e: CT: Map 128 bits labels to 32 bit map ID")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When deleting vxlan flow rule under multipath, tun_info in parse_attr is
not freed when the rule is not ready.

Fixes: ef06c9ee ("net/mlx5e: Allow one failure when offloading tc encap rules under multipath")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

As described in the previous commit, napi_synchronize doesn't quite fit
the purpose when we just need to wait until the currently running NAPI
quits. Its implementation waits until NAPI is not running by polling and
waiting for 1ms in between. In cases where we need to deactivate one
queue (e.g., recovery flows) or where we deactivate them one-by-one
(deactivate channel flow), we may get stuck in napi_synchronize forever
if other queues keep NAPI active, causing a soft lockup. Depending on
kernel configuration (CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC), it may result
in a kernel panic.

To fix the issue, use synchronize_rcu to wait for NAPI to quit, and wrap
the whole NAPI in rcu_read_lock.

Fixes: acc6c595 ("net/mlx5e: Split open/close channels to stages")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, the RQs are temporarily deactivated while hot-replacing the
XDP program, and napi_synchronize is used to make sure rq->xdp_prog is
not in use. However, napi_synchronize is not ideal: instead of waiting
till the end of a NAPI cycle, it polls and waits until NAPI is not
running, sleeping for 1ms between the periodic checks. Under heavy
workloads, this loop will never end, which may even lead to a kernel
panic if the kernel detects the hangup. Such workloads include XSK TX
and possibly also heavy RX (XSK or normal).

The fix is inspired by commit 326fe02d ("net/mlx4_en: protect
ring->xdp_prog with rcu_read_lock"). As mlx5e_xdp_handle is already
protected by rcu_read_lock, and bpf_prog_put uses call_rcu to free the
program, there is no need for additional synchronization if proper RCU
functions are used to access the pointer. This patch converts all
accesses to rq->xdp_prog to use RCU functions.

Fixes: 86994156 ("net/mlx5e: XDP fast RX drop bpf programs support")
Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, when an FTE is allocated, its refcount is decreased to 0
with the purpose it will not be a stand alone steering object and every
rule (destination) of the FTE would increase the refcount.
When mlx5_cleanup_fs is called while not all rules were deleted by the
steering users, it hit refcount underflow on the FTE once clean_tree
calls to tree_remove_node after the deleted rules already decreased
the refcount to 0.

FTE is no longer destroyed implicitly when the last rule (destination)
is deleted. mlx5_del_flow_rules avoids it by increasing the refcount on
the FTE and destroy it explicitly after all rules were deleted. So we
can avoid the refcount underflow by making FTE as stand alone object.
In addition need to set del_hw_func to FTE so the HW object will be
destroyed when the FTE is deleted from the cleanup_tree flow.

refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 15715 at lib/refcount.c:28 refcount_warn_saturate+0xd9/0xe0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
 tree_put_node+0xf2/0x140 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x5f/0xf0 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x5f/0xf0 [mlx5_core]
 mlx5_cleanup_fs+0x26/0x270 [mlx5_core]
 mlx5_unload+0x2e/0xa0 [mlx5_core]
 mlx5_unload_one+0x51/0x120 [mlx5_core]
 mlx5_devlink_reload_down+0x51/0x90 [mlx5_core]
 devlink_reload+0x39/0x120
 ? devlink_nl_cmd_reload+0x43/0x220
 genl_rcv_msg+0x1e4/0x420
 ? genl_family_rcv_msg_attrs_parse+0x100/0x100
 netlink_rcv_skb+0x47/0x110
 genl_rcv+0x24/0x40
 netlink_unicast+0x217/0x2f0
 netlink_sendmsg+0x30f/0x430
 sock_sendmsg+0x30/0x40
 __sys_sendto+0x10e/0x140
 ? handle_mm_fault+0xc4/0x1f0
 ? do_page_fault+0x33f/0x630
 __x64_sys_sendto+0x24/0x30
 do_syscall_64+0x48/0x130
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 718ce4d6 ("net/mlx5: Consolidate update FTE for all removal changes")
Fixes: bd71b08e ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

struct ethtool_fecparam carries bitmasks not bit numbers.
We want to return 1 (NONE), not 0.

Fixes: 0d087093 ("nfp: implement ethtool FEC mode settings")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rx_request_irq(), it will just return what irq_set_affinity_hint()
returns. If it is failed, the napi and irq requested are not freed
properly. So add exits for failures to handle these.
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: Unbind fixes

This patch series fixes a couple of issues with the unbinding of the PHY
drivers and then bringing down a network interface. The first is a NULL
pointer de-reference and the second was an incorrect warning being
triggered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When phy_is_started() was added to catch incorrect PHY states,
phy_stop() would not be qualified against PHY_DOWN. It is possible to
reach that state when the PHY driver has been unbound and the network
device is then brought down.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we have unbound the PHY driver prior to calling phy_detach() (often
via phy_disconnect()) then we can cause a NULL pointer de-reference
accessing the driver owner member. The steps to reproduce are:

echo unimac-mdio-0:01 > /sys/class/net/eth0/phydev/driver/unbind
ip link set eth0 down

Fixes: cafe8df8 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tunnel offload info code uses ETHTOOL_MSG_TUNNEL_INFO_GET message type (cmd
field in genetlink header) for replies to tunnel info netlink request, i.e.
the same value as the request have. This is a problem because we are using
two separate enums for userspace to kernel and kernel to userspace message
types so that this ETHTOOL_MSG_TUNNEL_INFO_GET (28) collides with
ETHTOOL_MSG_CABLE_TEST_TDR_NTF which is what message type 28 means for
kernel to userspace messages.

As the tunnel info request reached mainline in 5.9 merge window, we should
still be able to fix the reply message type without breaking backward
compatibility.

Fixes: c7d759eb ("ethtool: add tunnel info interface")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch sets skb->protocol before transmitting frames on the HDLC
device, so that a user listening on the HDLC device with an AF_PACKET
socket will see outgoing frames' sll_protocol field correctly set and
consistent with that of incoming frames.

1. Control frames in hdlc_cisco and hdlc_ppp

When these drivers send control frames, skb->protocol is not set.

This value should be set to htons(ETH_P_HDLC), because when receiving
control frames, their skb->protocol is set to htons(ETH_P_HDLC).

When receiving, hdlc_type_trans in hdlc.h is called, which then calls
cisco_type_trans or ppp_type_trans. The skb->protocol of control frames
is set to htons(ETH_P_HDLC) so that the control frames can be received
by hdlc_rcv in hdlc.c, which calls cisco_rx or ppp_rx to process the
control frames.

2. hdlc_fr

When this driver sends control frames, skb->protocol is set to internal
values used in this driver.

When this driver sends data frames (from upper stacked PVC devices),
skb->protocol is the same as that of the user data packet being sent on
the upper PVC device (for normal PVC devices), or is htons(ETH_P_802_3)
(for Ethernet-emulating PVC devices).

However, skb->protocol for both control frames and data frames should be
set to htons(ETH_P_HDLC), because when receiving, all frames received on
the HDLC device will have their skb->protocol set to htons(ETH_P_HDLC).

When receiving, hdlc_type_trans in hdlc.h is called, and because this
driver doesn't provide a type_trans function in struct hdlc_proto,
all frames will have their skb->protocol set to htons(ETH_P_HDLC).
The frames are then received by hdlc_rcv in hdlc.c, which calls fr_rx
to process the frames (control frames are consumed and data frames
are re-received on upper PVC devices).

Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver is a virtual driver stacked on top of Ethernet interfaces.

When this driver transmits data on the Ethernet device, the skb->protocol
setting is inconsistent with the Ethernet header prepended to the skb.

This causes a user listening on the Ethernet interface with an AF_PACKET
socket, to see different sll_protocol values for incoming and outgoing
frames, because incoming frames would have this value set by parsing the
Ethernet header.

This patch changes the skb->protocol value for outgoing Ethernet frames,
making it consistent with the Ethernet header prepended. This makes a
user listening on the Ethernet device with an AF_PACKET socket, to see
the same sll_protocol value for incoming and outgoing frames.

Cc: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the memory leak in mps during module unload
path by freeing mps reference entries if the list
adpter->mps_ref is not already empty

Fixes: 28b38705 ("cxgb4: Re-work the logic for mps refcounting")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest in the host-to-guest ring buffer. Ensure that
invalid values cannot cause indexing off the end of an array, or
subvert an existing validation via integer overflow. Ensure that
outgoing packets do not have any leftover guest memory that has not
been zeroed out.
Signed-off-by: Andres Beltran <lkmlabelt@gmail.com>
Co-developed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The KSZ9477 and KSZ8795 use the port_cnt field differently: For the
KSZ9477, it includes the CPU port(s), while for the KSZ8795, it doesn't.

It would be a good cleanup to make the handling of both drivers match,
but as a first step, fix the recently broken assignment of num_ports in
the KSZ8795 driver (which completely broke probing, as the CPU port
index was always failing the num_ports check).

Fixes: af199a1a ("net: dsa: microchip: set the correct number of ports")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds transport ports information for route lookup so that
IPsec can select Geneve tunnel traffic to do encryption. This is
needed for OVS/OVN IPsec with encrypted Geneve tunnels.

This can be tested by configuring a host-host VPN using an IKE
daemon and specifying port numbers. For example, for an
Openswan-type configuration, the following parameters should be
configured on both hosts and IPsec set up as-per normal:

$ cat /etc/ipsec.conf

conn in
...
left=$IP1
right=$IP2
...
leftprotoport=udp/6081
rightprotoport=udp
...
conn out
...
left=$IP1
right=$IP2
...
leftprotoport=udp
rightprotoport=udp/6081
...

The tunnel can then be setup using "ip" on both hosts (but
changing the relevant IP addresses):

$ ip link add tun type geneve id 1000 remote $IP2
$ ip addr add 192.168.0.1/24 dev tun
$ ip link set tun up

This can then be tested by pinging from $IP1:

$ ping 192.168.0.2

Without this patch the traffic is unencrypted on the wire.

Fixes: 2d07dc79 ("geneve: add initial netdev driver for GENEVE tunnels")
Signed-off-by: Qiuyu Xiao <qiuyu.xiao.qyx@gmail.com>
Signed-off-by: Mark Gray <mark.d.gray@redhat.com>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix some parameter description or spelling mistakes.
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2020-09-15

The following pull-request contains BPF updates for your *net* tree.

We've added 12 non-merge commits during the last 19 day(s) which contain
a total of 10 files changed, 47 insertions(+), 38 deletions(-).

The main changes are:

1) docs/bpf fixes, from Andrii.

2) ld_abs fix, from Daniel.

3) socket casting helpers fix, from Martin.

4) hash iterator fixes, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Running selftest
  ./btf_btf -p
the kernel had the following warning:
  [   51.528185] WARNING: CPU: 3 PID: 1756 at kernel/bpf/hashtab.c:717 htab_map_get_next_key+0x2eb/0x300
  [   51.529217] Modules linked in:
  [   51.529583] CPU: 3 PID: 1756 Comm: test_btf Not tainted 5.9.0-rc1+ #878
  [   51.530346] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.3-1.el7.centos 04/01/2014
  [   51.531410] RIP: 0010:htab_map_get_next_key+0x2eb/0x300
  ...
  [   51.542826] Call Trace:
  [   51.543119]  map_seq_next+0x53/0x80
  [   51.543528]  seq_read+0x263/0x400
  [   51.543932]  vfs_read+0xad/0x1c0
  [   51.544311]  ksys_read+0x5f/0xe0
  [   51.544689]  do_syscall_64+0x33/0x40
  [   51.545116]  entry_SYSCALL_64_after_hwframe+0x44/0xa9

The related source code in kernel/bpf/hashtab.c:
  709 static int htab_map_get_next_key(struct bpf_map *map, void *key, void *next_key)
  710 {
  711         struct bpf_htab *htab = container_of(map, struct bpf_htab, map);
  712         struct hlist_nulls_head *head;
  713         struct htab_elem *l, *next_l;
  714         u32 hash, key_size;
  715         int i = 0;
  716
  717         WARN_ON_ONCE(!rcu_read_lock_held());

In kernel/bpf/inode.c, bpffs map pretty print calls map->ops->map_get_next_key()
without holding a rcu_read_lock(), hence causing the above warning.
To fix the issue, just surrounding map->ops->map_get_next_key() with rcu read lock.

Fixes: a26ca7c9 ("bpf: btf: Add pretty print support to the basic arraymap")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200916004401.146277-1-yhs@fb.com

The bpf_skc_to_* type casting helpers are available to
BPF_PROG_TYPE_TRACING.  The traced PTR_TO_BTF_ID may be NULL.
For example, the skb->sk may be NULL.  Thus, these casting helpers
need to check "!sk" also and this patch fixes them.

Fixes: 0d4fad3e ("bpf: Add bpf_skc_to_udp6_sock() helper")
Fixes: 478cfbdf ("bpf: Add bpf_skc_to_{tcp, tcp_timewait, tcp_request}_sock() helpers")
Fixes: af7ec138 ("bpf: Add bpf_skc_to_tcp6_sock() helper")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200915182959.241101-1-kafai@fb.com

Kfir reported that pmtu exceptions are not created properly for
deployments where multipath routes use the same device.

After some digging I see 2 compounding problems:
1. ip_route_output_key_hash_rcu is updating the flowi4_oif *after*
   the route lookup. This is the second use case where this has
   been a problem (the first is related to use of vti devices with
   VRF). I can not find any reason for the oif to be changed after the
   lookup; the code goes back to the start of git. It does not seem
   logical so remove it.

2. fib_lookups for exceptions do not call fib_select_path to handle
   multipath route selection based on the hash.

The end result is that the fib_lookup used to add the exception
always creates it based using the first leg of the route.

An example topology showing the problem:

                 |  host1
             +------+
             | eth0 |  .209
             +------+
                 |
             +------+
     switch  | br0  |
             +------+
                 |
       +---------+---------+
       | host2             |  host3
   +------+             +------+
   | eth0 | .250        | eth0 | 192.168.252.252
   +------+             +------+

   +-----+             +-----+
   | vti | .2          | vti | 192.168.247.3
   +-----+             +-----+
       \                  /
 =================================
 tunnels
         192.168.247.1/24

for h in host1 host2 host3; do
        ip netns add ${h}
        ip -netns ${h} link set lo up
        ip netns exec ${h} sysctl -wq net.ipv4.ip_forward=1
done

ip netns add switch
ip -netns switch li set lo up
ip -netns switch link add br0 type bridge stp 0
ip -netns switch link set br0 up

for n in 1 2 3; do
        ip -netns switch link add eth-sw type veth peer name eth-h${n}
        ip -netns switch li set eth-h${n} master br0 up
        ip -netns switch li set eth-sw netns host${n} name eth0
done

ip -netns host1 addr add 192.168.252.209/24 dev eth0
ip -netns host1 link set dev eth0 up
ip -netns host1 route add 192.168.247.0/24 \
        nexthop via 192.168.252.250 dev eth0 nexthop via 192.168.252.252 dev eth0

ip -netns host2 addr add 192.168.252.250/24 dev eth0
ip -netns host2 link set dev eth0 up

ip -netns host2 addr add 192.168.252.252/24 dev eth0
ip -netns host3 link set dev eth0 up

ip netns add tunnel
ip -netns tunnel li set lo up
ip -netns tunnel li add br0 type bridge
ip -netns tunnel li set br0 up
for n in $(seq 11 20); do
        ip -netns tunnel addr add dev br0 192.168.247.${n}/24
done

for n in 2 3
do
        ip -netns tunnel link add vti${n} type veth peer name eth${n}
        ip -netns tunnel link set eth${n} mtu 1360 master br0 up
        ip -netns tunnel link set vti${n} netns host${n} mtu 1360 up
        ip -netns host${n} addr add dev vti${n} 192.168.247.${n}/24
done
ip -netns tunnel ro add default nexthop via 192.168.247.2 nexthop via 192.168.247.3

ip netns exec host1 ping -M do -s 1400 -c3 -I 192.168.252.209 192.168.247.11
ip netns exec host1 ping -M do -s 1400 -c3 -I 192.168.252.209 192.168.247.15
ip -netns host1 ro ls cache

Before this patch the cache always shows exceptions against the first
leg in the multipath route; 192.168.252.250 per this example. Since the
hash has an initial random seed, you may need to vary the final octet
more than what is listed. In my tests, using addresses between 11 and 19
usually found 1 that used both legs.

With this patch, the cache will have exceptions for both legs.

Fixes: 4895c771 ("ipv4: Add FIB nexthop exceptions")
Reported-by: Kfir Itzhak <mastertheknife@gmail.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix parameter description of tipc_link_bc_create()
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 16ad3f40 ("tipc: introduce variable window congestion control")
Signed-off-by: Lu Wei <luwei32@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update supporters for IBM Power SRIOV Virtual NIC Device Driver.
Thomas Falcon is moving on to other works. Dany Madden, Lijun Pan
and Sukadev Bhattiprolu are the current supporters.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make path to bench_ringbufs.c just a text, not a special link.

Fixes: 97abb2b3 ("docs/bpf: Add BPF ring buffer design notes")
Reported-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200915005031.2748397-1-andriin@fb.com

For AF_XDP sockets, there was a discrepancy between the number of of
pinned pages and the size of the umem region.

The size of the umem region is used to validate the AF_XDP descriptor
addresses. The logic that pinned the pages covered by the region only
took whole pages into consideration, creating a mismatch between the
size and pinned pages. A user could then pass AF_XDP addresses outside
the range of pinned pages, but still within the size of the region,
crashing the kernel.

This change correctly calculates the number of pages to be
pinned. Further, the size check for the aligned mode is
simplified. Now the code simply checks if the size is divisible by the
chunk size.

Fixes: bbff2f32 ("xsk: new descriptor addressing scheme")
Reported-by: Ciara Loftus <ciara.loftus@intel.com>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Ciara Loftus <ciara.loftus@intel.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200910075609.7904-1-bjorn.topel@gmail.com

In fl_set_erspan_opt(), all bits of erspan md was set 1, as this
function is also used to set opt MASK. However, when setting for
md->u.index for opt VALUE, the rest bits of the union md->u will
be left 1. It would cause to fail the match of the whole md when
version is 1 and only index is set.

This patch is to fix by initializing with 0 before setting erspan
md->u.
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: 79b1011c ("net: sched: allow flower to match erspan options")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
net: improve vxlan option process in net_sched and lwtunnel

This patch is to do some mask when setting vxlan option in net_sched
and lwtunnel, so that only available bits can be set on vxlan md gbp.

This would help when users don't know exactly vxlan's gbp bits, and
avoid some mismatch because of some unavailable bits set by users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.

So do the mask when set it in lwtunnel, as it does in act_tunnel_key and
cls_flower.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.

So we'd better do the mask when set it in act_tunnel_key and cls_flower.
Otherwise, when users don't know these bits, they may configure with a
value which can never be matched.
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In tipc_buf_append() it may change skb's frag_list, and it causes
problems when this skb is cloned. skb_unclone() doesn't really
make this skb's flag_list available to change.

Shuang Li has reported an use-after-free issue because of this
when creating quite a few macvlan dev over the same dev, where
the broadcast packets will be cloned and go up to the stack:

 [ ] BUG: KASAN: use-after-free in pskb_expand_head+0x86d/0xea0
 [ ] Call Trace:
 [ ]  dump_stack+0x7c/0xb0
 [ ]  print_address_description.constprop.7+0x1a/0x220
 [ ]  kasan_report.cold.10+0x37/0x7c
 [ ]  check_memory_region+0x183/0x1e0
 [ ]  pskb_expand_head+0x86d/0xea0
 [ ]  process_backlog+0x1df/0x660
 [ ]  net_rx_action+0x3b4/0xc90
 [ ]
 [ ] Allocated by task 1786:
 [ ]  kmem_cache_alloc+0xbf/0x220
 [ ]  skb_clone+0x10a/0x300
 [ ]  macvlan_broadcast+0x2f6/0x590 [macvlan]
 [ ]  macvlan_process_broadcast+0x37c/0x516 [macvlan]
 [ ]  process_one_work+0x66a/0x1060
 [ ]  worker_thread+0x87/0xb10
 [ ]
 [ ] Freed by task 3253:
 [ ]  kmem_cache_free+0x82/0x2a0
 [ ]  skb_release_data+0x2c3/0x6e0
 [ ]  kfree_skb+0x78/0x1d0
 [ ]  tipc_recvmsg+0x3be/0xa40 [tipc]

So fix it by using skb_unshare() instead, which would create a new
skb for the cloned frag and it'll be safe to change its frag_list.
The similar things were also done in sctp_make_reassembled_event(),
which is using skb_copy().
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: 37e22164 ("tipc: rename and move message reassembly function")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_group_add_to_tree() returns silently if `key` matches `nkey` of an
existing node, causing tipc_group_create_member() to leak memory. Let
tipc_group_add_to_tree() return an error in such a case, so that
tipc_group_create_member() can handle it properly.

Fixes: 75da2163 ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+f95d90c454864b3b5bc9@syzkaller.appspotmail.com
Cc: Hillf Danton <hdanton@sina.com>
Link: https://syzkaller.appspot.com/bug?id=048390604fe1b60df34150265479202f10e13affSigned-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

flowi4_multipath_hash was added by the commit referenced below for
tunnels. Unfortunately, the patch did not initialize the new field
for several fast path lookups that do not initialize the entire flow
struct to 0. Fix those locations. Currently, flowi4_multipath_hash
is random garbage and affects the hash value computed by
fib_multipath_hash for multipath selection.

Fixes: 24ba1440 ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hauke Mehrtens says:

====================
net: lantiq: Fix bugs in NAPI handling

This fixes multiple bugs in the NAPI handling.

Changes since:
v1:
 - removed stable tag from "net: lantiq: use netif_tx_napi_add() for TX NAPI"
 - Check the NAPI budged in "net: lantiq: Use napi_complete_done()"
 - Add extra fix "net: lantiq: Disable IRQs only if NAPI gets scheduled"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The napi_schedule() call will only schedule the NAPI if it is not
already running. To make sure that we do not deactivate interrupts
without scheduling NAPI only deactivate the interrupts in case NAPI also
gets scheduled.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use napi_complete_done() and activate the interrupts when this function
returns true. This way the generic NAPI code can take care of activating
the interrupts.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>