- 07 Jun, 2017 18 commits
-
-
Arnd Bergmann authored
We get a link error when CCU_MULT is not set with the newly added driver: drivers/clk/sunxi-ng/ccu-sun8i-a83t.o:(.data.__compound_literal.1+0x4): undefined reference to `ccu_mult_ops' drivers/clk/sunxi-ng/ccu-sun8i-a83t.o:(.data.__compound_literal.3+0x4): undefined reference to `ccu_mult_ops' Fixes: 46b492116666 ("clk: sunxi-ng: Add driver for A83T CCU") Signed-off-by:Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Chen-Yu Tsai <wens@csie.org>
-
Chen-Yu Tsai authored
The divider of the audio PLL has an offset of 1. Fix this in the driver. Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com>
-
Chen-Yu Tsai authored
The offset for the PLL lock status register was incorrectly set to 0x208, which actually points to an unused register. The correct register offset is 0x20c. Signed-off-by:
-
Chen-Yu Tsai authored
The A83T clock control unit is a hybrid of some new style clock designs from the A80, and old style layout from the other Allwinner SoCs. Like the A80, the SoC does not have a low speed 32.768 kHz oscillator. Unlike the A80, there is no clock input either. The only low speed clock available is the internal oscillator which runs at around 16 MHz, divided by 512, yielding a low speed clock around 31.250 kHz. Also, the MMC2 module clock supports switching to a "new timing" mode. This mode divides the clock output by half, and disables the CCU based clock delays. The MMC controller must be configure to the same mode, and then use its internal clock delays. This driver does not support runtime switching of the timing modes. Instead, the new timing mode is enforced at probe time. Consumers can check which mode is active by trying to get the current phase delay of the MMC2 phase clocks, which will return -ENOTSUPP if the new timing mode is active. Signed-off-by:
-
Chen-Yu Tsai authored
On the A83T, the AHB1 clock has a shared pre-divider on the two PLL-PERIPH clock parents. To support such instances of shared pre-dividers, this patch extends the mux clock type to support multiple variable pre-dividers. As the pre-dividers are only used to calculate the rate, but do not participate in the factorization process, this is fairly straightforward. Signed-off-by:
-
Chen-Yu Tsai authored
The A83T clock control unit is a hybrid of some new style clock designs from the A80, and old style layout from the other Allwinner SoCs. Like the A80, the SoC does not have a low speed 32.768 kHz oscillator. Unlike the A80, there is no clock input either. The only low speed clock available is the internal oscillator which runs at around 16 MHz, divided by 512, yielding a low speed clock around 31.250 kHz. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Wei Yongjun authored
PTR_ERR should access the value just tested by IS_ERR, otherwise the wrong error code will be returned. Fixes: b0d9a4bd52bd ("clk: sunxi-ng: add support for DE2 CCU") Signed-off-by:Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by:
-
Maxime Ripard authored
The video PLLs are used directly by the HDMI controller. Export them so that we can use them in our DT node. Signed-off-by:
-
Maxime Ripard authored
Currently, the parent rate given back to the clock framework in our request is the original parent rate we calculated before trying to round the rate of our clock. This works fine unless our clock also changes its parent rate, in which case we will simply ignore that change and still use the previous parent rate. Create a new function to re-adjust the parent rate to take the pre-dividers into account, and give that back to the clock framework. Signed-off-by:
-
Maxime Ripard authored
The current function name is a bit confusing, and doesn't really allow to create an explicit function to reverse the operation. We also for now change the parent rate through a pointer, while we don't return anything. In order to be less confusing, and easier to use for downstream users, change the function name to something hopefully clearer, and return the adjusted rate instead of changing the pointer. Signed-off-by:
-
Maxime Ripard authored
The pre-divider retrieval code was merged into the function to apply the current pre-divider onto the parent clock rate so that we can use that adjusted value to do our factors computation. However, since we'll need to do the reverse operation, we need to split out that code into a function that will be shared. Signed-off-by:
-
Maxime Ripard authored
The current code only rely on the parent to change its rate in the case where CLK_SET_RATE_PARENT is set. However, some clock rates might be obtained only through a modification of the parent and the clock divider. Just rely on the round rate of the clocks to give us the best computation that might be achieved for a given rate. round_rate functions now need to honor CLK_SET_RATE_PARENT, but either the functions already do that if they modify the parent, or don't modify the praents at all. Signed-off-by:
-
Maxime Ripard authored
divider_round_rate_parent already evaluates changing the parent rate if CLK_SET_RATE_PARENT is set. Now that we can do that on muxes too, let's just use it. Signed-off-by:
-
Maxime Ripard authored
The clocks might need to modify their parent clocks. In order to make that possible, give them access to the parent clock being evaluated, and to a pointer to the parent rate so that they can modify it if needed. Signed-off-by:
-
Maxime Ripard authored
So far, divider_round_rate only considers the parent clock returned by clk_hw_get_parent. This works fine on clocks that have a single parents, this doesn't work on muxes, since we will only consider the first parent, while other parents may totally be able to provide a better combination. Clocks in that case cannot use divider_round_rate, so would have to come up with a very similar logic to work around it. Instead of having to do something like this, and duplicate that logic everywhere, create a divider_round_rate parent to allow caller to give an additional parameter for the parent clock to consider. Reviewed-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Tobias Klauser authored
ccu_reset.h and ccu_reset.c use spinlock_t and associated functions but rely on implict inclusion of linux/spinlock.h which means that changes in other headers could break the build. Thus, add an explicit include. Signed-off-by:
Tobias Klauser <tklauser@distanz.ch> Acked-by:
-
Icenowy Zheng authored
The "Display Engine 2.0" in Allwinner newer SoCs contains a clock management unit for its subunits, like the DE CCU in A80. Add a sunxi-ng style driver for it. Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Signed-off-by:
-
Icenowy Zheng authored
Allwinner "Display Engine 2.0" contains some clock controls in it. In order to add them as clock drivers, we need a device tree binding. Add the binding here. Also add the device tree binding headers. Signed-off-by:
-
- 31 May, 2017 3 commits
-
-
Chen-Yu Tsai authored
The PRCM takes PLL_PERIPH0 as one of its parents for the AR100 clock. As such we need to be able to describe this relationship in the device tree. Export the PLL_PERIPH0 clock so we can reference it in the PRCM node. Signed-off-by:
-
Chen-Yu Tsai authored
The PRCM takes PLL_PERIPH0 as one of its parents for the AR100 clock. As such we need to be able to describe this relationship in the device tree. Export the PLL_PERIPH0 clock so we can reference it in the PRCM node. Signed-off-by:
-
Chen-Yu Tsai authored
The AR100 clock in the PRCM has parents, one of which is pll-periph from the main CCU. Add it to the list of required clocks for the PRCM CCU. Signed-off-by:
-
- 18 May, 2017 1 commit
-
-
Arnd Bergmann authored
The newly added PRCM CCU driver uses SUNXI_CCU_MP_WITH_MUX_GATE, which causes a link error when no other driver enables SUNXI_CCU_MP: drivers/clk/built-in.o:(.data+0x5c8c8): undefined reference to `ccu_mp_ops' This adds an explicit 'select' statement for it. Signed-off-by:
-
- 14 May, 2017 2 commits
-
-
Yong Deng authored
V3S's usb otg device reset bit should be 24, not 23. Cc: stable@vger.kernel.org Signed-off-by:
Yong Deng <iemdey@gmail.com> Reviewed-By:
-
Chen-Yu Tsai authored
The register offset for the lcd1-ch1 clock was incorrectly pointing to the lcd0-ch1 clock. This resulted in the lcd0-ch1 clock being disabled when the clk core disables unused clocks. This then stops the simplefb HDMI output path. Reported-by:
Bob Ham <rah@settrans.net> Fixes: c6e6c96d ("clk: sunxi-ng: Add A31/A31s clocks") Cc: stable@vger.kernel.org # 4.9.x- Signed-off-by:
-
- 13 May, 2017 5 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull some more input subsystem updates from Dmitry Torokhov: "An updated xpad driver with a few more recognized device IDs, and a new psxpad-spi driver, allowing connecting Playstation 1 and 2 joypads via SPI bus" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: cros_ec_keyb - remove extraneous 'const' Input: add support for PlayStation 1/2 joypads connected via SPI Input: xpad - add USB IDs for Mad Catz Brawlstick and Razer Sabertooth Input: xpad - sync supported devices with xboxdrv Input: xpad - sort supported devices by USB ID
-
git://git.infradead.org/linux-ubifsLinus Torvalds authored
Pull UBI/UBIFS updates from Richard Weinberger: - new config option CONFIG_UBIFS_FS_SECURITY - minor improvements - random fixes * tag 'upstream-4.12-rc1' of git://git.infradead.org/linux-ubifs: ubi: Add debugfs file for tracking PEB state ubifs: Fix a typo in comment of ioctl2ubifs & ubifs2ioctl ubifs: Remove unnecessary assignment ubifs: Fix cut and paste error on sb type comparisons ubi: fastmap: Fix slab corruption ubifs: Add CONFIG_UBIFS_FS_SECURITY to disable/enable security labels ubi: Make mtd parameter readable ubi: Fix section mismatch
-
git://git.kernel.org/pub/scm/linux/kernel/git/rw/umlLinus Torvalds authored
Pull UML fixes from Richard Weinberger: "No new stuff, just fixes" * 'for-linus-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: um: Add missing NR_CPUS include um: Fix to call read_initrd after init_bootmem um: Include kbuild.h instead of duplicating its macros um: Fix PTRACE_POKEUSER on x86_64 um: Set number of CPUs um: Fix _print_addr()
-
Linus Torvalds authored
Merge misc fixes from Andrew Morton: "15 fixes" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: mm, docs: update memory.stat description with workingset* entries mm: vmscan: scan until it finds eligible pages mm, thp: copying user pages must schedule on collapse dax: fix PMD data corruption when fault races with write dax: fix data corruption when fault races with write ext4: return to starting transaction in ext4_dax_huge_fault() mm: fix data corruption due to stale mmap reads dax: prevent invalidation of mapped DAX entries Tigran has moved mm, vmalloc: fix vmalloc users tracking properly mm/khugepaged: add missed tracepoint for collapse_huge_page_swapin gcov: support GCC 7.1 mm, vmstat: Remove spurious WARN() during zoneinfo print time: delete current_fs_time() hwpoison, memcg: forcibly uncharge LRU pages
-
- 12 May, 2017 11 commits
-
-
Roman Gushchin authored
Commit 4b4cea91691d ("mm: vmscan: fix IO/refault regression in cache workingset transition") introduced three new entries in memory stat file: - workingset_refault - workingset_activate - workingset_nodereclaim This commit adds a corresponding description to the cgroup v2 docs. Link: http://lkml.kernel.org/r/1494530293-31236-1-git-send-email-guro@fb.comSigned-off-by:Roman Gushchin <guro@fb.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: Li Zefan <lizefan@huawei.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Minchan Kim authored
Although there are a ton of free swap and anonymous LRU page in elgible zones, OOM happened. balloon invoked oom-killer: gfp_mask=0x17080c0(GFP_KERNEL_ACCOUNT|__GFP_ZERO|__GFP_NOTRACK), nodemask=(null), order=0, oom_score_adj=0 CPU: 7 PID: 1138 Comm: balloon Not tainted 4.11.0-rc6-mm1-zram-00289-ge228d67e9677-dirty #17 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014 Call Trace: oom_kill_process+0x21d/0x3f0 out_of_memory+0xd8/0x390 __alloc_pages_slowpath+0xbc1/0xc50 __alloc_pages_nodemask+0x1a5/0x1c0 pte_alloc_one+0x20/0x50 __pte_alloc+0x1e/0x110 __handle_mm_fault+0x919/0x960 handle_mm_fault+0x77/0x120 __do_page_fault+0x27a/0x550 trace_do_page_fault+0x43/0x150 do_async_page_fault+0x2c/0x90 async_page_fault+0x28/0x30 Mem-Info: active_anon:424716 inactive_anon:65314 isolated_anon:0 active_file:52 inactive_file:46 isolated_file:0 unevictable:0 dirty:27 writeback:0 unstable:0 slab_reclaimable:3967 slab_unreclaimable:4125 mapped:133 shmem:43 pagetables:1674 bounce:0 free:4637 free_pcp:225 free_cma:0 Node 0 active_anon:1698864kB inactive_anon:261256kB active_file:208kB inactive_file:184kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:532kB dirty:108kB writeback:0kB shmem:172kB writeback_tmp:0kB unstable:0kB all_unreclaimable? no DMA free:7316kB min:32kB low:44kB high:56kB active_anon:8064kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB writepending:0kB present:15992kB managed:15908kB mlocked:0kB slab_reclaimable:464kB slab_unreclaimable:40kB kernel_stack:0kB pagetables:24kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB lowmem_reserve[]: 0 992 992 1952 DMA32 free:9088kB min:2048kB low:3064kB high:4080kB active_anon:952176kB inactive_anon:0kB active_file:36kB inactive_file:0kB unevictable:0kB writepending:88kB present:1032192kB managed:1019388kB mlocked:0kB slab_reclaimable:13532kB slab_unreclaimable:16460kB kernel_stack:3552kB pagetables:6672kB bounce:0kB free_pcp:56kB local_pcp:24kB free_cma:0kB lowmem_reserve[]: 0 0 0 959 Movable free:3644kB min:1980kB low:2960kB high:3940kB active_anon:738560kB inactive_anon:261340kB active_file:188kB inactive_file:640kB unevictable:0kB writepending:20kB present:1048444kB managed:1010816kB mlocked:0kB slab_reclaimable:0kB slab_unreclaimable:0kB kernel_stack:0kB pagetables:0kB bounce:0kB free_pcp:832kB local_pcp:60kB free_cma:0kB lowmem_reserve[]: 0 0 0 0 DMA: 1*4kB (E) 0*8kB 18*16kB (E) 10*32kB (E) 10*64kB (E) 9*128kB (ME) 8*256kB (E) 2*512kB (E) 2*1024kB (E) 0*2048kB 0*4096kB = 7524kB DMA32: 417*4kB (UMEH) 181*8kB (UMEH) 68*16kB (UMEH) 48*32kB (UMEH) 14*64kB (MH) 3*128kB (M) 1*256kB (H) 1*512kB (M) 2*1024kB (M) 0*2048kB 0*4096kB = 9836kB Movable: 1*4kB (M) 1*8kB (M) 1*16kB (M) 1*32kB (M) 0*64kB 1*128kB (M) 2*256kB (M) 4*512kB (M) 1*1024kB (M) 0*2048kB 0*4096kB = 3772kB 378 total pagecache pages 17 pages in swap cache Swap cache stats: add 17325, delete 17302, find 0/27 Free swap = 978940kB Total swap = 1048572kB 524157 pages RAM 0 pages HighMem/MovableOnly 12629 pages reserved 0 pages cma reserved 0 pages hwpoisoned [ pid ] uid tgid total_vm rss nr_ptes nr_pmds swapents oom_score_adj name [ 433] 0 433 4904 5 14 3 82 0 upstart-udev-br [ 438] 0 438 12371 5 27 3 191 -1000 systemd-udevd With investigation, skipping page of isolate_lru_pages makes reclaim void because it returns zero nr_taken easily so LRU shrinking is effectively nothing and just increases priority aggressively. Finally, OOM happens. The problem is that get_scan_count determines nr_to_scan with eligible zones so although priority drops to zero, it couldn't reclaim any pages if the LRU contains mostly ineligible pages. get_scan_count: size = lruvec_lru_size(lruvec, lru, sc->reclaim_idx); size = size >> sc->priority; Assumes sc->priority is 0 and LRU list is as follows. N-N-N-N-H-H-H-H-H-H-H-H-H-H-H-H-H-H-H-H (Ie, small eligible pages are in the head of LRU but others are almost ineligible pages) In that case, size becomes 4 so VM want to scan 4 pages but 4 pages from tail of the LRU are not eligible pages. If get_scan_count counts skipped pages, it doesn't reclaim any pages remained after scanning 4 pages so it ends up OOM happening. This patch makes isolate_lru_pages try to scan pages until it encounters eligible zones's pages. [akpm@linux-foundation.org: clean up mind-bending `for' statement. Tweak comment text] Fixes: 3db65812 ("Revert "mm, vmscan: account for skipped pages as a partial scan"") Link: http://lkml.kernel.org/r/1494457232-27401-1-git-send-email-minchan@kernel.orgSigned-off-by:Minchan Kim <minchan@kernel.org> Acked-by:
Michal Hocko <mhocko@suse.com> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
David Rientjes authored
We have encountered need_resched warnings in __collapse_huge_page_copy() while doing {clear,copy}_user_highpage() over HPAGE_PMD_NR source pages. mm->mmap_sem is held for write, but the iteration is well bounded. Reschedule as needed. Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1705101426380.109808@chino.kir.corp.google.comSigned-off-by:David Rientjes <rientjes@google.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by:
-
Ross Zwisler authored
This is based on a patch from Jan Kara that fixed the equivalent race in the DAX PTE fault path. Currently DAX PMD read fault can race with write(2) in the following way: CPU1 - write(2) CPU2 - read fault dax_iomap_pmd_fault() ->iomap_begin() - sees hole dax_iomap_rw() iomap_apply() ->iomap_begin - allocates blocks dax_iomap_actor() invalidate_inode_pages2_range() - there's nothing to invalidate grab_mapping_entry() - we add huge zero page to the radix tree and map it to page tables The result is that hole page is mapped into page tables (and thus zeros are seen in mmap) while file has data written in that place. Fix the problem by locking exception entry before mapping blocks for the fault. That way we are sure invalidate_inode_pages2_range() call for racing write will either block on entry lock waiting for the fault to finish (and unmap stale page tables after that) or read fault will see already allocated blocks by write(2). Fixes: 9f141d6e ("dax: Call ->iomap_begin without entry lock during dax fault") Link: http://lkml.kernel.org/r/20170510172700.18991-1-ross.zwisler@linux.intel.comSigned-off-by:Ross Zwisler <ross.zwisler@linux.intel.com> Reviewed-by:
Jan Kara <jack@suse.cz> Cc: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Jan Kara authored
Currently DAX read fault can race with write(2) in the following way: CPU1 - write(2) CPU2 - read fault dax_iomap_pte_fault() ->iomap_begin() - sees hole dax_iomap_rw() iomap_apply() ->iomap_begin - allocates blocks dax_iomap_actor() invalidate_inode_pages2_range() - there's nothing to invalidate grab_mapping_entry() - we add zero page in the radix tree and map it to page tables The result is that hole page is mapped into page tables (and thus zeros are seen in mmap) while file has data written in that place. Fix the problem by locking exception entry before mapping blocks for the fault. That way we are sure invalidate_inode_pages2_range() call for racing write will either block on entry lock waiting for the fault to finish (and unmap stale page tables after that) or read fault will see already allocated blocks by write(2). Fixes: 9f141d6e Link: http://lkml.kernel.org/r/20170510085419.27601-5-jack@suse.czSigned-off-by: -
Jan Kara authored
DAX will return to locking exceptional entry before mapping blocks for a page fault to fix possible races with concurrent writes. To avoid lock inversion between exceptional entry lock and transaction start, start the transaction already in ext4_dax_huge_fault(). Fixes: 9f141d6e Link: http://lkml.kernel.org/r/20170510085419.27601-4-jack@suse.czSigned-off-by:
-
Jan Kara authored
Currently, we didn't invalidate page tables during invalidate_inode_pages2() for DAX. That could result in e.g. 2MiB zero page being mapped into page tables while there were already underlying blocks allocated and thus data seen through mmap were different from data seen by read(2). The following sequence reproduces the problem: - open an mmap over a 2MiB hole - read from a 2MiB hole, faulting in a 2MiB zero page - write to the hole with write(3p). The write succeeds but we incorrectly leave the 2MiB zero page mapping intact. - via the mmap, read the data that was just written. Since the zero page mapping is still intact we read back zeroes instead of the new data. Fix the problem by unconditionally calling invalidate_inode_pages2_range() in dax_iomap_actor() for new block allocations and by properly invalidating page tables in invalidate_inode_pages2_range() for DAX mappings. Fixes: c6dcf52c Link: http://lkml.kernel.org/r/20170510085419.27601-3-jack@suse.czSigned-off-by:
-
Ross Zwisler authored
Patch series "mm,dax: Fix data corruption due to mmap inconsistency", v4. This series fixes data corruption that can happen for DAX mounts when page faults race with write(2) and as a result page tables get out of sync with block mappings in the filesystem and thus data seen through mmap is different from data seen through read(2). The series passes testing with t_mmap_stale test program from Ross and also other mmap related tests on DAX filesystem. This patch (of 4): dax_invalidate_mapping_entry() currently removes DAX exceptional entries only if they are clean and unlocked. This is done via: invalidate_mapping_pages() invalidate_exceptional_entry() dax_invalidate_mapping_entry() However, for page cache pages removed in invalidate_mapping_pages() there is an additional criteria which is that the page must not be mapped. This is noted in the comments above invalidate_mapping_pages() and is checked in invalidate_inode_page(). For DAX entries this means that we can can end up in a situation where a DAX exceptional entry, either a huge zero page or a regular DAX entry, could end up mapped but without an associated radix tree entry. This is inconsistent with the rest of the DAX code and with what happens in the page cache case. We aren't able to unmap the DAX exceptional entry because according to its comments invalidate_mapping_pages() isn't allowed to block, and unmap_mapping_range() takes a write lock on the mapping->i_mmap_rwsem. Since we essentially never have unmapped DAX entries to evict from the radix tree, just remove dax_invalidate_mapping_entry(). Fixes: c6dcf52c ("mm: Invalidate DAX radix tree entries only if appropriate") Link: http://lkml.kernel.org/r/20170510085419.27601-2-jack@suse.czSigned-off-by: -
Andrew Morton authored
Cc: Tigran Aivazian <aivazian.tigran@gmail.com> Signed-off-by:
-
Michal Hocko authored
Commit 1f5307b1 ("mm, vmalloc: properly track vmalloc users") has pulled asm/pgtable.h include dependency to linux/vmalloc.h and that turned out to be a bad idea for some architectures. E.g. m68k fails with In file included from arch/m68k/include/asm/pgtable_mm.h:145:0, from arch/m68k/include/asm/pgtable.h:4, from include/linux/vmalloc.h:9, from arch/m68k/kernel/module.c:9: arch/m68k/include/asm/mcf_pgtable.h: In function 'nocache_page': >> arch/m68k/include/asm/mcf_pgtable.h:339:43: error: 'init_mm' undeclared (first use in this function) #define pgd_offset_k(address) pgd_offset(&init_mm, address) as spotted by kernel build bot. nios2 fails for other reason In file included from include/asm-generic/io.h:767:0, from arch/nios2/include/asm/io.h:61, from include/linux/io.h:25, from arch/nios2/include/asm/pgtable.h:18, from include/linux/mm.h:70, from include/linux/pid_namespace.h:6, from include/linux/ptrace.h:9, from arch/nios2/include/uapi/asm/elf.h:23, from arch/nios2/include/asm/elf.h:22, from include/linux/elf.h:4, from include/linux/module.h:15, from init/main.c:16: include/linux/vmalloc.h: In function '__vmalloc_node_flags': include/linux/vmalloc.h:99:40: error: 'PAGE_KERNEL' undeclared (first use in this function); did you mean 'GFP_KERNEL'? which is due to the newly added #include <asm/pgtable.h>, which on nios2 includes <linux/io.h> and thus <asm/io.h> and <asm-generic/io.h> which again includes <linux/vmalloc.h>. Tweaking that around just turns out a bigger headache than necessary. This patch reverts 1f5307b1 and reimplements the original fix in a different way. __vmalloc_node_flags can stay static inline which will cover vmalloc* functions. We only have one external user (kvmalloc_node) and we can export __vmalloc_node_flags_caller and provide the caller directly. This is much simpler and it doesn't really need any games with header files. [akpm@linux-foundation.org: coding-style fixes] [mhocko@kernel.org: revert old comment] Link: http://lkml.kernel.org/r/20170509211054.GB16325@dhcp22.suse.cz Fixes: 1f5307b1 ("mm, vmalloc: properly track vmalloc users") Link: http://lkml.kernel.org/r/20170509153702.GR6481@dhcp22.suse.czSigned-off-by:
-
SeongJae Park authored
One return case of `__collapse_huge_page_swapin()` does not invoke tracepoint while every other return case does. This commit adds a tracepoint invocation for the case. Link: http://lkml.kernel.org/r/20170507101813.30187-1-sj38.park@gmail.comSigned-off-by:
SeongJae Park <sj38.park@gmail.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
-
