We should use the same buffer size we set up for DMA also in the hardware
descriptor. Previously we used common->rx_bufsize for setting up the DMA
mapping, but used skb_tailroom(skb) for the size we tell to the hardware in the
descriptor itself. The problem is that skb_tailroom(skb) can give us a larger
value than the size we set up for DMA before. This allows the hardware to write
into memory locations not set up for DMA. In practice this should rarely happen
because all packets should be smaller than the maximum 802.11 packet size.

On the tested platform rx_bufsize is 2528, and we allocated an skb of 2559
bytes length (including padding for cache alignment) but sbk_tailroom() was
2592. Just consistently use rx_bufsize for all RX DMA memory sizes.

Also use the return value of the descriptor setup function.

Cc: stable@kernel.org
Signed-off-by: Bruno Randolf <br1@einfach.org>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Specifying a valid channel type will get
goto out rather than continuing, due to
missing braces. This affects both remain
on channel and action frame TX commands.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Remove (hopefully) last use of WEXT in rndis_wlan. Replace wireless_send_event
with missing cfg80211_disconnected in rndis_wlan_do_link_down_work.
Reported-by: "Rogério Brito" <rbrito@ime.usp.br>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We tried to squeeze as much AR9003 support into this kernel
release cycle but there are a few features which are still
being tested and developed. Some of these features are critical
to the stable operation of AR9003 so for now disable AR9003 support
all together. This will get re-enabled once all necessary features
are in place but very likely will not happen for 2.6.35.
Reviewed-by: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since wdev can be NULL, check it before dereferencing it
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The current frame length used by the driver for RX frames is the SPI bus
transfer length. This length has padding bytes, which do not belong to the
WLAN frame.

As there is no other length information in the WLAN frame except the skb
length this problem caused for instance extra ESSID's to be listed at the
end of scan results (IE id 0) with zero length.

Fix the frame length by removing padding.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is possible for internal scan to race against itself if the device is
not returning the scan results from first requests. What happens in this
case is the cleanup done during the abort of the first internal scan also
cleans up part of the new scan, causing it to access memory it shouldn't.

Here are details:
* First internal scan is triggered and scan command sent to device.
* After seven seconds there is no scan results so the watchdog timer
  triggers a scan abort.
* The scan abort succeeds and a SCAN_COMPLETE_NOTIFICATION is received for
 failed scan.
* During processing of SCAN_COMPLETE_NOTIFICATION we clear STATUS_SCANNING
  and queue the "scan_completed" work.
** At this time, since the problem that caused the internal scan in first
   place is still present, a new internal scan is triggered.
The behavior at this point is a bit different between 2.6.34 and 2.6.35
since 2.6.35 has a lot of this synchronized. The rest of the race
description will thus be generalized.
** As part of preparing for the scan "is_internal_short_scan" is set to
true.
* At this point the completion work for fist scan is run. As part of this
  there is some locking missing around the "is_internal_short_scan"
  variable and it is set to "false".
** Now the second scan runs and it considers itself a real (not internal0
   scan and thus causes problems with wrong memory being accessed.

The fix is twofold.
* Since "is_internal_short_scan" should be protected by mutex, fix this in
  scan completion work so that changes to it can be serialized.
* Do not queue a new internal scan if one is in progress.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=15824Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

signal_type is enum cfg80211_signal_type.

This fixes the gcc warning:

scan.c: In function `cfg80211_inform_bss':
scan.c:518:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'
scan.c: In function `cfg80211_inform_bss_frame':
scan.c:574:6: warning: comparison between `enum cfg80211_signal_type' and `enum nl80211_bss'
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix some issues introduced in batch skb dequeuing for input_pkt_queue.
The primary issue it that the queue head must be incremented only
after a packet has been processed, that is only after
__netif_receive_skb has been called.  This is needed for the mechanism
to prevent OOO packet in RFS.  Also when flushing the input_pkt_queue
and process_queue, the process queue should be done first to prevent
OOO packets.

Because the input_pkt_queue has been effectively split into two queues,
the calculation of the tail ptr is no longer correct.  The correct value
would be head+input_pkt_queue->len+process_queue->len.  To avoid
this calculation we added an explict input_queue_tail in softnet_data.
The tail value is simply incremented when queuing to input_pkt_queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As remarked by Sam Ravnborg the spin_lock variable, that has been introduced
in commit 57c8a456 ("can: Fix SJA1000 command
register writes on SMP systems") has not been initialized properly.

This patch adds the initialization to allow spinlock debugging.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
CC: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocated memory for IRQs should be freed when releasing the mii_bus
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When GRO produces fraglist entries, and the resulting skb hits
an interface that is incapable of TSO but capable of FRAGLIST,
we end up producing a bogus packet with gso_size non-zero.

This was reported in the field with older versions of KVM that
did not set the TSO bits on tuntap.

This patch fixes that.
Reported-by: Igor Zhang <yugzhang@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (229 commits)
  USB: remove unused usb_buffer_alloc and usb_buffer_free macros
  usb: musb: update gfp/slab.h includes
  USB: ftdi_sio: fix legacy SIO-device header
  USB: kl5usb105: reimplement using generic framework
  USB: kl5usb105: minor clean ups
  USB: kl5usb105: fix memory leak
  USB: io_ti: use kfifo to implement write buffering
  USB: io_ti: remove unsused private counter
  USB: ti_usb: use kfifo to implement write buffering
  USB: ir-usb: fix incorrect write-buffer length
  USB: aircable: fix incorrect write-buffer length
  USB: safe_serial: straighten out read processing
  USB: safe_serial: reimplement read using generic framework
  USB: safe_serial: reimplement write using generic framework
  usb-storage: always print quirks
  USB: usb-storage: trivial debug improvements
  USB: oti6858: use port write fifo
  USB: oti6858: use kfifo to implement write buffering
  USB: cypress_m8: use kfifo to implement write buffering
  USB: cypress_m8: remove unused drain define
  ...

Fix up conflicts (due to usb_buffer_alloc/free renaming) in
	drivers/input/tablet/acecad.c
	drivers/input/tablet/kbtab.c
	drivers/input/tablet/wacom_sys.c
	drivers/media/video/gspca/gspca.c
	sound/usb/usbaudio.c

This is needed before the USB merge.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c

* 'docs-next' of git://git.lwn.net/linux-2.6:
  Add a document describing the padata interface

* 'viafb-next' of git://git.lwn.net/linux-2.6: (35 commits)
  viafb: move some include files to include/linux
  viafb: Eliminate some global.h references
  viafb: get rid of i2c debug cruft
  viafb: fold via_io.h into via-core.h
  viafb: Fix initialization error paths
  viafb: Do not remove gpiochip under spinlock
  viafb: make procfs entries optional
  viafb: fix proc entry removal
  viafb: improve misc register handling
  viafb: replace inb/outb
  viafb: move some modesetting functions to a seperate file
  viafb: unify modesetting functions
  viafb: Reserve framebuffer memory for the upcoming camera driver
  viafb: Add a simple VX855 DMA engine driver
  viafb: Add a simple interrupt management infrastructure
  via: Rationalize vt1636 detection
  viafb: Introduce viafb_find_i2c_adapter()
  via: Do not attempt I/O on inactive I2C adapters
  viafb: Turn GPIO and i2c into proper platform devices
  viafb: Convert GPIO and i2c to the new indexed port ops
  ...

Now that all callers are converted over, remove the compatibility
functions and all is good.

Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Length field of header was incorrectly set to available payload space
rather than the actual payload size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Kill custom read and write implementations (static per-port,
singleton(!) urb pool).

Also remove changelog header (can be retrieved through git).

Read processing and write-buffer handling tested using a cp210x device
in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Whitespace changes and some removed comments.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Private data was not freed on error path in startup.

Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Kill custom fifo implementation.

Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Kill custom fifo implementation.

Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Returned length should include header length.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Returned length should include header length.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Clean up read processing logic.

Tested using a cp210x device in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use process_read_urb to implement read processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Kill custom single-urb write implementation.

Note that this driver still depended on the write callback from the old
generic framework.

Tested against original read processing using a cp210x device in a
loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Right now quirks are printed only when the are manually overriden with
the module parameters. It's not so useful to remind the user that his
parameters are correctly applied; what is useful is to print out the
quirks the user is not aware are being applied.

So let's do the smart thing and print the quirks when they are present.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use pr_foo and dev_foo instead of printk. Maybe US_DEBUG* should be
replaced too.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Kill private write fifo and use port fifo instead (protected under
port lock).

Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Kill custom fifo implementation.

Use private write fifo to minimise changes to lock handling.

Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Kill custom fifo implementation.

Note that cypress_m8 has no port write fifo as it has no bulk-out
endpoint.

Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Driver uses tty-port drain these days.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use bulk_out_size in usb_serial_driver to set urb buffer size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>