this patch adds avdd-0v9-supply and avdd-1v8-supply to hdmi node for
Radxa ROCK 4 series.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-6-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

sort nodes/properties alphabetically
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-5-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

fix regulator name

ref:
 https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi4_v13_sch_20181112.pdfSigned-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-4-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

sort nodes/properties alphabetically
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-3-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

fix regulator name.
also, add vcc_3v3 and vdd_log.

ref:
 https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi4c_plus_v12_sch_220304.pdfSigned-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-2-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

GPIO pins for LEDs on ROCK 4C+ are in APIO5
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220909195006.127957-1-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds the DSI controller nodes and DSI-DPHY controller nodes to the
rk356x device tree.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220919164616.12492-4-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This enables the GPU and HDMI output (including HDMI audio) on
the PINE64 Quartz64 Model B single board computer.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20220920143446.633956-1-frattaroli.nicolas@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The only diffrence against the standrard edition is that the enterprise
one has a built-in EEPROM chip which stores a globally unique MAC address.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Link: https://lore.kernel.org/r/20220915022511.4267-2-cnsztl@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add devicetree binding documentation for the FriendlyARM NanoPi R4S
Enterprise Edition.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220915022511.4267-1-cnsztl@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The Rockchip PX30 SoC has three I2S controllers, i2s1 and i2s2 are
2-channel I2S/PCM controllers handled by the same controller driver, and
i2s0 a 8-channel I2S/PCM/TDM controller handled by another controller
driver.

This adds the device tree node required to enable I2S0 on PX30.

This was tested in a 2-channel I2S with TX BCLK/LRCK for both TX and RX
(rockchip,trcm-sync-tx-only) setup on a soon-to-be-released board.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20220916091746.35108-1-foss+kernel@0leil.netSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add avdd-0v9-supply and avdd-1v8-supply to hdmi node for
rk3399-roc-pc to silence dmesg warning and match the name
of the 1v8 supply to the circuit sheet.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/20220915111138.1108-1-m.reichl@fivetechno.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The Gru-Scarlet family includes a variety of SKU identifiers, using
parts of a 3-bit space {0..7}. SKU2 and SKU4 devices (under a few
different manufacturer names) also use the Innolux display.

Without this, a SKU2 device may non-deterministically (depending on the
matching order of DTBs and bootloader behavior) select either one of the
INX DTBs (rk3399-gru-scarlet-dumo.dtb or rk3399-gru-scarlet-inx.dtb) or
the KingDisplay DTB (rk3399-gru-scarlet-kd.dtb), to ill effect.

For reference, the original vendor tree source:

CHROMIUM: arm64: dts: rockchip: add sku{0,2,4} compatibility
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/f6ed665c9e2eb37fb2680debbb36ec9fb0e8fb97

CHROMIUM: arm64: dts: rockchip: scarlet: add SKU0 device tree
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/9987c8776f4b087d135d761e59f7fa6cc83fc7fcSigned-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220817123350.2.I5f4fd0808a927b08e267c189712fb4a85931fd3b@changeidSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The Gru-Scarlet family includes a variety of SKU identifiers, using
parts of a 3-bit space {0..7}. SKU2 and SKU4 devices (under a few
different manufacturer names) also use the Innolux display.

For reference, the original vendor tree source:

CHROMIUM: arm64: dts: rockchip: add sku{0,2,4} compatibility
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/f6ed665c9e2eb37fb2680debbb36ec9fb0e8fb97

CHROMIUM: arm64: dts: rockchip: scarlet: add SKU0 device tree
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/9987c8776f4b087d135d761e59f7fa6cc83fc7fcSigned-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220817123350.1.Ibb15bab32dbfa0d89f86321c4eae7adbc8d7ad4a@changeidSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Define the memory region on RK3399 VOPs containing the gamma LUT at
base+0x2000.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Tested-by: Linus Heckemann <git@sphalerite.org>
Link: https://lore.kernel.org/r/20211019215843.42718-4-sigmaris@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the device tree nodes to enable video output on the Station M2.
Enable the GPU and HDMI nodes and fix the GPU regulator range.
Signed-off-by: Furkan Kardame <f.kardame@manjaro.org>
Link: https://lore.kernel.org/r/20220627202208.45770-1-f.kardame@manjaro.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.

In order to:
  1. prevent BCLK from turning on by other component.
  2. keep BCLK and LRCLK being present at the same time

This patch adjusts the device tree to allow BCLK to switch
to GPIO func before LRCLK output, and switch back during
LRCLK is output.
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220708080726.4170711-1-judyhsiao@chromium.orgSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The RK3566 and RK3568 come with a dedicated Hantro instance solely for
encoding. This patch adds a node for this to the device tree, along with
a node for its MMU.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20220612155346.16288-4-frattaroli.nicolas@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

RK356x has Hantro G1 video decoder capable to decode MPEG2/H.264/VP8
video formats.

This patch enables RK356x video decoder in RK356x device-tree
include.

Tested on [1] with FFmpeg v4l2_request code taken from [2]
with MPEG2, H.642 and VP8 samples with results [3].

[1] https://github.com/warpme/minimyth2
[2] https://github.com/LibreELEC/LibreELEC.tv/blob/master/packages/multimedia/ffmpeg/patches/v4l2-request/ffmpeg-001-v4l2-request.patch
[3] https://github.com/warpme/minimyth2/blob/master/video-test-summary.txtSigned-off-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Link: https://lore.kernel.org/r/20220214212955.1178947-2-piotr.oniszczuk@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the nodes to enable the PCIe controller on the
Radxa ROCK3 Model A board. Run test with the MT7921
pcie wireless card.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20220726023516.6487-1-amadeus@jmu.edu.cnSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add devicetree node for hym8563 rtc to
Radxa ROCK3 Model A board.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://lore.kernel.org/r/20220726023046.5876-1-amadeus@jmu.edu.cnSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This adds the regulator node to the quartz64-b device tree,
and enables the PCIe 2 controller and combphy for it.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20220718033145.792657-1-frattaroli.nicolas@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Anbernic RG353P and RG503 are both RK3566 based handheld gaming devices
from Anbernic.

Both devices have:
 - 2 SDMMC slots.
 - A Realtek rtl8821cs WiFi/Bluetooth adapter.
 - A mini HDMI port.
 - A USB C host port and a USB C otg port (currently only working as
   device).
 - Multiple GPIO buttons and a single ADC button.
 - Dual analog joysticks controlled via a GPIO mux.
 - A headphone jack with amplified stereo speakers via a SGM4865 amp.
 - A PWM based vibrator for force feedback.

The RG353P has:
 - 2GB LPDDR4 RAM.
 - A 32GB eMMC.
 - A 3.5 inch 640x480 4-lane DSI panel of unknown origin with an i2c
   controlled touchscreen (touchscreen is a Hynitron CST340).

The RG503 has:
 - 1GB LPDDR4 RAM.
 - A 5 inch 960x544 AMOLED 2-lane DSI/DBI panel manufactured by Samsung
   with part number ams495qa04. Data for this panel is provided via the
   DSI interface, however commands are sent via a 9-bit 3-wire SPI
   interface. The MISO pin of SPI3 of the SOC is wired to the input of
   the panel, so it must be bitbanged.

This devicetree enables the following hardware:
 - HDMI (plus audio).
 - Analog audio, including speakers.
 - All buttons.
 - All SDMMC/eMMC/SDIO controllers.
 - The ADC joysticks (note a pending patch is required to use them).
 - WiFi/Bluetooth (note out of tree drivers are required).
 - The PWM based vibrator motor.

The following hardware is not enabled:
 - The display panels (drivers are being written and there are issues
   with the upstream DSI and VOP2 subsystems).
 - Battery (driver pending).
 - Touchscreen on the RG353P (note the i2c2 bus is enabled for it).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20220906210324.28986-4-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add entry for the Anbernic RG353P and RG503 handheld devices.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220906210324.28986-3-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Anbernic designs and manufactures portable gaming systems.
https://anbernic.com/Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220906210324.28986-2-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add -regulator suffix to regulator names on Banana Pi R2 Pro board as
discussed on Mailinglist
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220906164212.84835-1-linux@fw-web.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

add support for user LEDs on Radxa ROCK 4C+ board.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220908031726.1307105-2-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

only user_led2 (blue) is supported.

user_led1 (green) is not connected to any gpio so it cannot be
controlled.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20220908031726.1307105-1-naoki@radxa.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the new rk817 charger driver to the Odroid Go Advance. Create a
monitored battery node as well for the charger to use. All values
from monitored battery are gathered from the BSP kernel for the
Odroid Go Advance provided by HardKernel.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Link: https://lore.kernel.org/r/20220827021623.23829-5-macroalpha82@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Voltage constraints on vccio_sd are invalid. They don't match the voltages
that LDO9 can generate, and this causes rk808-regulator driver to fail
to probe with -EINVAL when it tries to apply the constraints during boot.

Fix the constraints to something that LDO9 can be actually configured for.

Fixes: 78a21c7d ("arm64: dts: rockchip: Add initial support for Pine64 PinePhone Pro")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Tested-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Link: https://lore.kernel.org/r/20220904233652.3197885-1-megi@xff.czSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for Radxa ROCK 4C+ SBC.

Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec

Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220902065057.97425-3-jagan@amarulasolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

RK3399-T is down-clocked version of RK3399 SoC operated at 1.5GHz.

Add CPU operating points table for it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220902065057.97425-2-jagan@amarulasolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Document the dt-bindings for Radxa ROCK 4C+ SBC.

Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec

Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20220902065057.97425-1-jagan@amarulasolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This is a basic DT containing regulators and UART, intended to be a
base that myself and others can add additional nodes in future patches.

Tested to work: booting from eMMC/SD, output over UART.

https://wiki.pine64.org/wiki/PinePhone_Pro

This is derived from the community pine64-org repo[0] with fixes from
https://megous.com/git/linux.

0. https://gitlab.com/pine64-org/linux/-/commit/261d3b5f8ac503f97da810986d1d6422430c8531Signed-off-by: Martijn Braam <martijn@brixit.nl>
Co-developed-by: Kamil Trzciński <ayufan@ayufan.eu>
[no SoB, but Kamil is happy for this patch to be submitted]
Co-developed-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Co-developed-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Reviewed-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Tested-by: Nícolas F. R. A. Prado <n@nfraprado.net>
Link: https://lore.kernel.org/r/20220829050040.17330-2-tom@tom-fitzhenry.me.ukSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Document board compatible names for Pine64 PinePhonePro.

https://wiki.pine64.org/wiki/PinePhone_ProSigned-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Caleb Connolly <kc@postmarketos.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220815123004.252014-2-tom@tom-fitzhenry.me.ukSigned-off-by: Heiko Stuebner <heiko@sntech.de>

EAIDK-610 is from OPEN AI LAB and popularly used by university
students.

Specification:
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- 12V DC Power supply

This patch is test on Armbain and Glodroid with
HDMI/GPU/USB HOST/Type-C ADB/WIFI/BT.
Signed-off-by: Andy Yan <andyshrk@163.com>
Link: https://lore.kernel.org/r/20220709103016.2754044-1-andyshrk@163.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

EAIDK-610 is a rk3399 based board from OPEN AI LAB
and popularly used by university students.

Specification:
- Rockchip RK3399
- LPDDR3 4GB
- TF sd scard slot
- eMMC
- AP6255 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- 12V DC Power supply
Signed-off-by: Andy Yan <andyshrk@163.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220709103001.2753992-1-andyshrk@163.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add vendor prefixes for OPEN AI LAB.
Signed-off-by: Andy Yan <andyshrk@163.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220709102942.2753939-1-andyshrk@163.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add the MIPI CSI DPHY node to the RK356x device tree.
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220720091527.1270365-4-michael.riesch@wolfvision.netSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add Nodes to Bananapi-R2-Pro board to support PCIe v3 and
set PCIe related regulators to always on.
Suggested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220825193836.54262-6-linux@fw-web.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>