- 13 Jul, 2011 4 commits
-
-
Felix Fietkau authored
rfgain probe is only necessary for OFDM operation on AR5111 and AR5112. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Senthil Balasubramanian authored
Decryping frames on key_miss handling shouldn't be done for Michael MIC failed frames as h/w would have already decrypted such frames successfully anyway. Also leaving CRC and PHY error(where the frame is going to be dropped anyway), we are left to prcoess Decrypt error for which s/w decrypt is selected anway and so having key_miss as a separate check doesn't serve anything. So making key_miss handling mutually exlusive with other RX status handling makes much more sense. This patch addresses an issue with STA not reporting MIC failure events resulting in STA being disconnected immediately. Cc: stable@kernel.org Signed-off-by:
Senthil Balasubramanian <senthilb@qca.qualcomm.com> Signed-off-by:
-
Joe Perches authored
Multiple quoted strings are concatenated without comma separators. Make the array const while there. Signed-off-by:
Joe Perches <joe@perches.com> Acked-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Joe Perches authored
Multiple quoted strings are concatenated without comma separators. Signed-off-by:
-
- 11 Jul, 2011 36 commits
-
-
Wey-Yi Guy authored
Fix the compile warning cause by [IWL_TM_ATTR_MAX - 1] Reported-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Mohammed Shafi Shajakhan authored
Signed-off-by:
Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by:
-
Eduardo Bacchi Kienetz authored
Belkin's Connect N150 Wireless USB Adapter, model F7D1101 version 2, uses ID 0x945b. Chipset info: rt: 3390, rf: 000b, rev: 3213. I have just bought one, which started to work perfectly after the ID was added through this patch. Signed-off-by:
Eduardo Bacchi Kienetz <eduardo@kienetz.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Joe Perches authored
Signed-off-by:
Pavel Roskin <proski@gnu.org> Signed-off-by:
-
Larry Finger authored
A typo causes routine rtl92cu_phy_rf6052_set_cck_txpower() to test the same condition twice. The problem was found using cppcheck-1.49, and the proper fix was verified against the pre-mac80211 version of the code. Reported-by:
David Binderman <dcb314@hotmail.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: stable <stable@kernel.org> [back to 2.6.39] Signed-off-by:
-
Daniel Drake authored
When commands time out, corruption ensues. As lbs_complete_command() is called without locking, the command node is mistakenly freed twice. Also fixed up locking here in a few other places. The nature of command timeout may be that the card didn't even acknowledge receipt of the request. Detect this case and reset dnld_sent so that other commands don't hang forever. When cmdnodes are moved between the free list and the pending list, their list heads should be reinitialized. Fixed this. Sometimes commands are completed without actually submitting them or removing them from cmdpendingq. We must remember to remove them from cmdpendingq in these cases, so handle this in lbs_complete_command(). Harmless signals generated during suspend/resume were interrupting lbs_cmd. Convert to an uninterruptible sleep to avoid this. lbs_thread must be woken up every time there is some new work to do. I found that when 2 commands are queued, ther completion of the first command would not wake up lbs_thread to submit the second. Poke lbs_thread at the end of lbs_complete_command() to fix this. Signed-off-by:
Daniel Drake <dsd@laptop.org> Signed-off-by:
-
Johannes Berg authored
We don't have multiple RX queues, so there's no use in allocating multiple, use alloc_netdev_mqs() to allocate multiple TX but only one RX queue. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
I changed the TKIP key functions, but forgot to update the documentation includes, fix that. Signed-off-by:
-
Johannes Berg authored
Looks like I forgot to document the "gfp" parameter to cfg80211_gtk_rekey_notify, add it. Signed-off-by:
-
Hauke Mehrtens authored
The SoCs like the bcm4716 do not have a sprom on the bcma bus like a pcie device. It stores the values in some partition on flash memory. For ssb this informations are read out in the bcm47xx arch code, something like that should also be implemented for bcma. Without this patch bcma panics on SoCs. Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
-
Olivier Sobrie authored
Problems located in the two functions lbs_set_reg() and lbs_get_reg(): - The offset field of struct cmd_ds_reg_access was not filled in - The test on the return code of lbs_cmd_with_response() in function lbs_get_reg() was inverted Signed-off-by:
Olivier Sobrie <olivier@sobrie.be> Signed-off-by:
-
Pavel Roskin authored
Signed-off-by:
-
Pavel Roskin authored
Signed-off-by:
-
Felix Fietkau authored
AR_AN_SYNTH9 is in the analog shift register range and thus needs to be written using the ath9k_hw_analog_shift_rmw function. Signed-off-by:
-
Felix Fietkau authored
The radio needs twice / four times as much time to stabilize for half/quarter channels. Signed-off-by:
-
Felix Fietkau authored
The radio seems to perform better that way Signed-off-by:
-
Felix Fietkau authored
Now that the clock rate is initialized properly and SIFS, EIFS, USEC, slot time and ACK timeout are properly calculated by the generic code, the 'async FIFO' register hacks are no longer necessary. Signed-off-by:
-
Felix Fietkau authored
Initialize the the clock-to-TSF field of AR_USEC and the SIFS and EIFS time registers based on the clock rate instead of relying on initvals. With those changes, some of the hardcoded AR9287 1.3+ specific overrides can be dropped. Signed-off-by:
-
Felix Fietkau authored
This chip uses the async FIFO feature and runs the MAC at 117 MHz Signed-off-by:
-
Felix Fietkau authored
Enabling half/quarter rate makes the MAC run at half/quarter clock speed. Signed-off-by:
-
Felix Fietkau authored
All devices support this, but some disable it using an EEPROM flag for some reason. Improves 5 GHz performance on those devices. Signed-off-by:
-
Felix Fietkau authored
Use the proper masks for the register instead. Fixes adding the (still unused) half/quarter PLL flags. Signed-off-by:
-
Amitkumar Karwar authored
Currently device is not able to transmit in 40MHz in spite of enabling 40MHz support in HTCapInfo IE in assoc req, because 11n specific FW capabilities for transmission are not initialized. This patch adds code to initilize these capabilities. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
Kiran Divekar <dkiran@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Don Fry authored
Not needed since the driver split. Move single use routines to calling location and keep static where possible. Signed-off-by:
Don Fry <donald.h.fry@intel.com> Signed-off-by:
-
Wey-Yi Guy authored
For testing purpose, we need better control of msc from user application. Separate the fixed_rate between debugfs and testmode and enforce it. Signed-off-by:
Kenny Hsu <kenny.hsu@intel.com> Signed-off-by:
-
Wey-Yi Guy authored
The only host command allow to send to uCode is the one initiated from testmode if testmode is the owner of uCode Signed-off-by:
-
Wey-Yi Guy authored
Since we open the door to allow application control the device behavior through testmode, add command to allow application request the ownership of the uCode Signed-off-by:
-
Wey-Yi Guy authored
For all the hist command request from testmode, set the CMD_ON_DEMAND flag. this flag will be used later to control the uCode behavior Signed-off-by:
-
Wey-Yi Guy authored
Declare iwl_mac_rssi_callback as "static" Signed-off-by:
-
Meenakshi Venkataraman authored
WiFi throughput drops drastically when BT is turned on, BT and WiFi are simultaneously transmitting/receiving traffic. This is particularly true when BT has higher priority over WiFi, and hence the device defers TX frames. The AP assumes that the channel is bad and reduces the data rate, implying longer airtime, which exacerbates the problem further, resulting ultimately in what is popularly called the "death-spiral" phenomenon. The use of PS-poll in such scenarios guarantees a low but consistent throughput. Since the death-spiral phenomenon is observed only when the RSSI is low, use PS-poll only when RSSI is low and disable when high, with a known hysterisis. This feature specifies the high and low thresholds and implements the callbacks registered with mac80211, which will be called when threshold events occur. iwlwifi: dynamic pspoll: optimize rssi monitor code Signed-off-by:
Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Signed-off-by:
-
Meenakshi Venkataraman authored
mac80211 maintains a running average of the RSSI when a STA is associated to an AP. Report threshold events to any driver that has registered callbacks for getting RSSI measurements. Implement callbacks in mac80211 so that driver can set thresholds. Add callbacks in mac80211 which is invoked when an RSSI threshold event occurs. mac80211: add tracing to rssi_reports api and remove extraneous fn argument mac80211: scale up rssi thresholds from driver by 16 before storing Signed-off-by:
-
Wey-Yi Guy authored
For bt combo devices, need to use bt enabled handlers and functions Reported-by:
-
Wey-Yi Guy authored
No need to do double level indirect call after driver split no functional changes Signed-off-by:
-
Fry, Donald H authored
Not needed since the driver split. Eliminate redundant routine. Signed-off-by:
-
Fry, Donald H authored
Not needed since the driver split. Signed-off-by:
-
Fry, Donald H authored
Not needed since the driver split. Signed-off-by:
-
