- 12 Feb, 2019 40 commits
-
-
Jia-Ju Bai authored
[ Upstream commit 7418e652 ] In drivers/isdn/hisax/hfc_pci.c, the functions hfcpci_interrupt() and HFCPCI_l1hw() may be concurrently executed. HFCPCI_l1hw() line 1173: if (!cs->tx_skb) hfcpci_interrupt() line 942: spin_lock_irqsave(); line 1066: dev_kfree_skb_irq(cs->tx_skb); Thus, a possible concurrency use-after-free bug may occur in HFCPCI_l1hw(). To fix these bugs, the calls to spin_lock_irqsave() and spin_unlock_irqrestore() are added in HFCPCI_l1hw(), to protect the access to cs->tx_skb. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Minchan Kim authored
[ Upstream commit 3c9959e0 ] Patch series "zram idle page writeback", v3. Inherently, swap device has many idle pages which are rare touched since it was allocated. It is never problem if we use storage device as swap. However, it's just waste for zram-swap. This patchset supports zram idle page writeback feature. * Admin can define what is idle page "no access since X time ago" * Admin can define when zram should writeback them * Admin can define when zram should stop writeback to prevent wearout Details are in each patch's description. This patch (of 7): ================================ WARNING: inconsistent lock state 4.19.0+ #390 Not tainted -------------------------------- inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. zram_verify/2095 [HC0[0]:SC1[1]:HE1:SE0] takes: 00000000b1828693 (&(&zram->bitmap_lock)->rlock){+.?.}, at: put_entry_bdev+0x1e/0x50 {SOFTIRQ-ON-W} state was registered at: _raw_spin_lock+0x2c/0x40 zram_make_request+0x755/0xdc9 generic_make_request+0x373/0x6a0 submit_bio+0x6c/0x140 __swap_writepage+0x3a8/0x480 shrink_page_list+0x1102/0x1a60 shrink_inactive_list+0x21b/0x3f0 shrink_node_memcg.constprop.99+0x4f8/0x7e0 shrink_node+0x7d/0x2f0 do_try_to_free_pages+0xe0/0x300 try_to_free_pages+0x116/0x2b0 __alloc_pages_slowpath+0x3f4/0xf80 __alloc_pages_nodemask+0x2a2/0x2f0 __handle_mm_fault+0x42e/0xb50 handle_mm_fault+0x55/0xb0 __do_page_fault+0x235/0x4b0 page_fault+0x1e/0x30 irq event stamp: 228412 hardirqs last enabled at (228412): [<ffffffff98245846>] __slab_free+0x3e6/0x600 hardirqs last disabled at (228411): [<ffffffff98245625>] __slab_free+0x1c5/0x600 softirqs last enabled at (228396): [<ffffffff98e0031e>] __do_softirq+0x31e/0x427 softirqs last disabled at (228403): [<ffffffff98072051>] irq_exit+0xd1/0xe0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&zram->bitmap_lock)->rlock); <Interrupt> lock(&(&zram->bitmap_lock)->rlock); *** DEADLOCK *** no locks held by zram_verify/2095. stack backtrace: CPU: 5 PID: 2095 Comm: zram_verify Not tainted 4.19.0+ #390 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 Call Trace: <IRQ> dump_stack+0x67/0x9b print_usage_bug+0x1bd/0x1d3 mark_lock+0x4aa/0x540 __lock_acquire+0x51d/0x1300 lock_acquire+0x90/0x180 _raw_spin_lock+0x2c/0x40 put_entry_bdev+0x1e/0x50 zram_free_page+0xf6/0x110 zram_slot_free_notify+0x42/0xa0 end_swap_bio_read+0x5b/0x170 blk_update_request+0x8f/0x340 scsi_end_request+0x2c/0x1e0 scsi_io_completion+0x98/0x650 blk_done_softirq+0x9e/0xd0 __do_softirq+0xcc/0x427 irq_exit+0xd1/0xe0 do_IRQ+0x93/0x120 common_interrupt+0xf/0xf </IRQ> With writeback feature, zram_slot_free_notify could be called in softirq context by end_swap_bio_read. However, bitmap_lock is not aware of that so lockdep yell out: get_entry_bdev spin_lock(bitmap->lock); irq softirq end_swap_bio_read zram_slot_free_notify zram_slot_lock <-- deadlock prone zram_free_page put_entry_bdev spin_lock(bitmap->lock); <-- deadlock prone With akpm's suggestion (i.e. bitmap operation is already atomic), we could remove bitmap lock. It might fail to find a empty slot if serious contention happens. However, it's not severe problem because huge page writeback has already possiblity to fail if there is severe memory pressure. Worst case is just keeping the incompressible in memory, not storage. The other problem is zram_slot_lock in zram_slot_slot_free_notify. To make it safe is this patch introduces zram_slot_trylock where zram_slot_free_notify uses it. Although it's rare to be contented, this patch adds new debug stat "miss_free" to keep monitoring how often it happens. Link: http://lkml.kernel.org/r/20181127055429.251614-2-minchan@kernel.orgSigned-off-by:
Minchan Kim <minchan@kernel.org> Reviewed-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Reviewed-by:
Joey Pabalinas <joeypabalinas@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Waiman Long authored
[ Upstream commit 3c0c12cc ] When CONFIG_KASAN is enabled on large memory SMP systems, the deferrred pages initialization can take a long time. Below were the reported init times on a 8-socket 96-core 4TB IvyBridge system. 1) Non-debug kernel without CONFIG_KASAN [ 8.764222] node 1 initialised, 132086516 pages in 7027ms 2) Debug kernel with CONFIG_KASAN [ 146.288115] node 1 initialised, 132075466 pages in 143052ms So the page init time in a debug kernel was 20X of the non-debug kernel. The long init time can be problematic as the page initialization is done with interrupt disabled. In this particular case, it caused the appearance of following warning messages as well as NMI backtraces of all the cores that were doing the initialization. [ 68.240049] rcu: INFO: rcu_sched detected stalls on CPUs/tasks: [ 68.241000] rcu: 25-...0: (100 ticks this GP) idle=b72/1/0x4000000000000000 softirq=915/915 fqs=16252 [ 68.241000] rcu: 44-...0: (95 ticks this GP) idle=49a/1/0x4000000000000000 softirq=788/788 fqs=16253 [ 68.241000] rcu: 54-...0: (104 ticks this GP) idle=03a/1/0x4000000000000000 softirq=721/825 fqs=16253 [ 68.241000] rcu: 60-...0: (103 ticks this GP) idle=cbe/1/0x4000000000000000 softirq=637/740 fqs=16253 [ 68.241000] rcu: 72-...0: (105 ticks this GP) idle=786/1/0x4000000000000000 softirq=536/641 fqs=16253 [ 68.241000] rcu: 84-...0: (99 ticks this GP) idle=292/1/0x4000000000000000 softirq=537/537 fqs=16253 [ 68.241000] rcu: 111-...0: (104 ticks this GP) idle=bde/1/0x4000000000000000 softirq=474/476 fqs=16253 [ 68.241000] rcu: (detected by 13, t=65018 jiffies, g=249, q=2) The long init time was mainly caused by the call to kasan_free_pages() to poison the newly initialized pages. On a 4TB system, we are talking about almost 500GB of memory probably on the same node. In reality, we may not need to poison the newly initialized pages before they are ever allocated. So KASAN poisoning of freed pages before the completion of deferred memory initialization is now disabled. Those pages will be properly poisoned when they are allocated or freed after deferred pages initialization is done. With this change, the new page initialization time became: [ 21.948010] node 1 initialised, 132075466 pages in 18702ms This was still about double the non-debug kernel time, but was much better than before. Link: http://lkml.kernel.org/r/1544459388-8736-1-git-send-email-longman@redhat.comSigned-off-by:
Waiman Long <longman@redhat.com> Reviewed-by:
-
Larry Chen authored
[ Upstream commit 9e6aea22 ] Included file path was hard-wired in the ocfs2 makefile, which might causes some confusion when compiling ocfs2 as an external module. Say if we compile ocfs2 module as following. cp -r /kernel/tree/fs/ocfs2 /other/dir/ocfs2 cd /other/dir/ocfs2 make -C /path/to/kernel_source M=`pwd` modules Acutally, the compiler wil try to find included file in /kernel/tree/fs/ocfs2, rather than the directory /other/dir/ocfs2. To fix this little bug, we introduce the var $(src) provided by kbuild. $(src) means the absolute path of the running kbuild file. Link: http://lkml.kernel.org/r/20181108085546.15149-1-lchen@suse.comSigned-off-by:
Larry Chen <lchen@suse.com> Reviewed-by:
-
Junxiao Bi authored
[ Upstream commit 70306d9d ] For sync io read in ocfs2_read_blocks_sync(), first clear bh uptodate flag and submit the io, second wait io done, last check whether bh uptodate, if not return io error. If two sync io for the same bh were issued, it could be the first io done and set uptodate flag, but just before check that flag, the second io came in and cleared uptodate, then ocfs2_read_blocks_sync() for the first io will return IO error. Indeed it's not necessary to clear uptodate flag, as the io end handler end_buffer_read_sync() will set or clear it based on io succeed or failed. The following message was found from a nfs server but the underlying storage returned no error. [4106438.567376] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2780 ERROR: read block 1238823695 failed -5 [4106438.567569] (nfsd,7146,3):ocfs2_get_suballoc_slot_bit:2812 ERROR: status = -5 [4106438.567611] (nfsd,7146,3):ocfs2_test_inode_bit:2894 ERROR: get alloc slot and bit failed -5 [4106438.567643] (nfsd,7146,3):ocfs2_test_inode_bit:2932 ERROR: status = -5 [4106438.567675] (nfsd,7146,3):ocfs2_get_dentry:94 ERROR: test inode bit failed -5 Same issue in non sync read ocfs2_read_blocks(), fixed it as well. Link: http://lkml.kernel.org/r/20181121020023.3034-4-junxiao.bi@oracle.comSigned-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Changwei Ge <ge.changwei@h3c.com> Reviewed-by:
Yiwen Jiang <jiangyiwen@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Signed-off-by:
-
Randy Dunlap authored
[ Upstream commit 440e7b37 ] arch/sh/boards/mach-kfr2r09/setup.c does not need to #include <mtd/onenand.h>, and doing so causes a build warning, so drop that header file. In file included from ../arch/sh/boards/mach-kfr2r09/setup.c:28: ../include/linux/mtd/onenand.h:225:12: warning: 'struct mtd_oob_ops' declared inside parameter list will not be visible outside of this definition or declaration struct mtd_oob_ops *ops); Link: http://lkml.kernel.org/r/702f0a25-c63e-6912-4640-6ab0f00afbc7@infradead.org Fixes: f3590dc3 ("media: arch: sh: kfr2r09: Use new renesas-ceu camera driver") Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Reported-by:
Geert Uytterhoeven <geert@linux-m68k.org> Suggested-by:
Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by:
-
Marc Zyngier authored
[ Upstream commit 67a28de4 ] Running something like: decodecode vmlinux . leads to interested results where not only the leading "." gets stripped from the displayed paths, but also anywhere in the string, displaying something like: kvm_vcpu_check_block (arch/arm64/kvm/virt/kvm/kvm_mainc:2141) which doesn't help further processing. Fix it by only stripping the base path if it is a prefix of the path. Link: http://lkml.kernel.org/r/20181210174659.31054-3-marc.zyngier@arm.comSigned-off-by:
Marc Zyngier <marc.zyngier@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Jiri Olsa authored
[ Upstream commit a389aece ] Ondřej reported that when compiled with python3, the python extension regresses in evlist.get_pollfd function behaviour. The evlist.get_pollfd function creates file objects from evlist's fds and returns them in a list. The python3 version also sets them to 'close the original descriptor' when the object dies (is closed), by passing True via the 'closefd' arg in the PyFile_FromFd call. The python's closefd doc says: If closefd is False, the underlying file descriptor will be kept open when the file is closed. That's why the following line in python3 closes all evlist fds: evlist.get_pollfd() the returned list is immediately destroyed and that takes down the original events fds. Passing closefd as False to PyFile_FromFd to fix this. Reported-by:
Ondřej Lysoněk <olysonek@redhat.com> Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jaroslav Škarvada <jskarvad@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 66dfdff0 ("perf tools: Add Python 3 support") Link: http://lkml.kernel.org/r/20181226112121.5285-1-jolsa@kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Ondrej Mosnacek authored
[ Upstream commit e250d91d ] This fixes the case where all mount options specified are consumed by an LSM and all that's left is an empty string. In this case cgroupfs should accept the string and not fail. How to reproduce (with SELinux enabled): # umount /sys/fs/cgroup/unified # mount -o context=system_u:object_r:cgroup_t:s0 -t cgroup2 cgroup2 /sys/fs/cgroup/unified mount: /sys/fs/cgroup/unified: wrong fs type, bad option, bad superblock on cgroup2, missing codepage or helper program, or other error. # dmesg | tail -n 1 [ 31.575952] cgroup: cgroup2: unknown option "" Fixes: 67e9c74b ("cgroup: replace __DEVEL__sane_behavior with cgroup2 fs type") [NOTE: should apply on top of commit 5136f636 ("cgroup: implement "nsdelegate" mount option"), older versions need manual rebase] Suggested-by:
Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by:
Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Sahitya Tummala authored
[ Upstream commit e4589fa5 ] When there is a failure in f2fs_fill_super() after/during the recovery of fsync'd nodes, it frees the current sbi and retries again. This time the mount is successful, but the files that got recovered before retry, still holds the extent tree, whose extent nodes list is corrupted since sbi and sbi->extent_list is freed up. The list_del corruption issue is observed when the file system is getting unmounted and when those recoverd files extent node is being freed up in the below context. list_del corruption. prev->next should be fffffff1e1ef5480, but was (null) <...> kernel BUG at kernel/msm-4.14/lib/list_debug.c:53! lr : __list_del_entry_valid+0x94/0xb4 pc : __list_del_entry_valid+0x94/0xb4 <...> Call trace: __list_del_entry_valid+0x94/0xb4 __release_extent_node+0xb0/0x114 __free_extent_tree+0x58/0x7c f2fs_shrink_extent_tree+0xdc/0x3b0 f2fs_leave_shrinker+0x28/0x7c f2fs_put_super+0xfc/0x1e0 generic_shutdown_super+0x70/0xf4 kill_block_super+0x2c/0x5c kill_f2fs_super+0x44/0x50 deactivate_locked_super+0x60/0x8c deactivate_super+0x68/0x74 cleanup_mnt+0x40/0x78 __cleanup_mnt+0x1c/0x28 task_work_run+0x48/0xd0 do_notify_resume+0x678/0xe98 work_pending+0x8/0x14 Fix this by not creating extents for those recovered files if shrinker is not registered yet. Once mount is successful and shrinker is registered, those files can have extents again. Signed-off-by:
Sahitya Tummala <stummala@codeaurora.org> Signed-off-by:
Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 26fd962b ] niu_pci_eeprom_read() may fail, so we should check its return value before using the read data. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Acked-by:
Shannon Nelson <shannon.lee.nelson@gmail.com> Signed-off-by:
-
Anton Ivanov authored
[ Upstream commit 8892d854 ] Changing protection is a very high cost operation in UML because in addition to an extra syscall it also interrupts mmap merge sequences generated by the tlb. While the condition is not particularly common it is worth avoiding. Signed-off-by:
Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
-
Sahitya Tummala authored
[ Upstream commit 60aa4d55 ] iput() on sbi->node_inode can update sbi->stat_info in the below context, if the f2fs_write_checkpoint() has failed with error. f2fs_balance_fs_bg+0x1ac/0x1ec f2fs_write_node_pages+0x4c/0x260 do_writepages+0x80/0xbc __writeback_single_inode+0xdc/0x4ac writeback_single_inode+0x9c/0x144 write_inode_now+0xc4/0xec iput+0x194/0x22c f2fs_put_super+0x11c/0x1e8 generic_shutdown_super+0x70/0xf4 kill_block_super+0x2c/0x5c kill_f2fs_super+0x44/0x50 deactivate_locked_super+0x60/0x8c deactivate_super+0x68/0x74 cleanup_mnt+0x40/0x78 Fix this by moving f2fs_destroy_stats() further below iput() in both f2fs_put_super() and f2fs_fill_super() paths. Signed-off-by:
Chao Yu <yuchao0@huawei.com> Signed-off-by:
-
Ronnie Sahlberg authored
[ Upstream commit 59a63e47 ] RHBZ: 1021460 There is an issue where when multiple threads open/close the same directory ntwrk_buf_start might end up being NULL, causing the call to smbCalcSize later to oops with a NULL deref. The real bug is why this happens and why this can become NULL for an open cfile, which should not be allowed. This patch tries to avoid a oops until the time when we fix the underlying issue. Signed-off-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
Stefan Roese authored
[ Upstream commit 0b153944 ] Testing has shown, that when using mainline U-Boot on MT7688 based boards, the system may hang or crash while mounting the root-fs. The main issue here is that mainline U-Boot configures EBase to a value near the end of system memory. And with CONFIG_CPU_MIPSR2_IRQ_VI disabled, trap_init() will not allocate a new area to place the exception handler. The original value will be used and the handler will be copied to this location, which might already be used by some userspace application. The MT7688 supports VI - its config3 register is 0x00002420, so VInt (Bit 5) is set. But without setting CONFIG_CPU_MIPSR2_IRQ_VI this bit will not be evaluated to result in "cpu_has_vi" being set. This patch now selects CONFIG_CPU_MIPSR2_IRQ_VI on MT7620/8 which results trap_init() to allocate some memory for the exception handler. Please note that this issue was not seen with the Mediatek U-Boot version, as it does not touch EBase (stays at default of 0x8000.0000). This is strictly also not correct as the kernel (_text) resides here. Signed-off-by:
Stefan Roese <sr@denx.de> [paul.burton@mips.com: s/beeing/being/] Signed-off-by:
Paul Burton <paul.burton@mips.com> Cc: John Crispin <blogic@openwrt.org> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 5ac93f80 ] Clang warns when one enumerated type is implicitly converted to another: drivers/crypto/ux500/hash/hash_core.c:169:4: warning: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Wenum-conversion] direction, DMA_CTRL_ACK | DMA_PREP_INTERRUPT); ^~~~~~~~~ 1 warning generated. dmaengine_prep_slave_sg expects an enum from dma_transfer_direction. We know that the only direction supported by this function is DMA_TO_DEVICE because of the check at the top of this function so we can just use the equivalent value from dma_transfer_direction. DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1 Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 9d880c59 ] Clang warns when one enumerated type is implicitly converted to another: drivers/crypto/ux500/cryp/cryp_core.c:559:5: warning: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Wenum-conversion] direction, DMA_CTRL_ACK); ^~~~~~~~~ drivers/crypto/ux500/cryp/cryp_core.c:583:5: warning: implicit conversion from enumeration type 'enum dma_data_direction' to different enumeration type 'enum dma_transfer_direction' [-Wenum-conversion] direction, ^~~~~~~~~ 2 warnings generated. dmaengine_prep_slave_sg expects an enum from dma_transfer_direction. Because we know the value of the dma_data_direction enum from the switch statement, we can just use the proper value from dma_transfer_direction so there is no more conversion. DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1 DMA_FROM_DEVICE = DMA_DEV_TO_MEM = 2 Signed-off-by:
-
Michael Ellerman authored
[ Upstream commit 0464ed24 ] Currently seq_buf_puts() will happily create a non null-terminated string for you in the buffer. This is particularly dangerous if the buffer is on the stack. For example: char buf[8]; char secret = "secret"; struct seq_buf s; seq_buf_init(&s, buf, sizeof(buf)); seq_buf_puts(&s, "foo"); printk("Message is %s\n", buf); Can result in: Message is fooªªªªªsecret We could require all users to memset() their buffer to zero before use. But that seems likely to be forgotten and lead to bugs. Instead we can change seq_buf_puts() to always leave the buffer in a null-terminated state. The only downside is that this makes the buffer 1 character smaller for seq_buf_puts(), but that seems like a good trade off. Link: http://lkml.kernel.org/r/20181019042109.8064-1-mpe@ellerman.id.auAcked-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 9aa3aa15 ] In lm80_probe(), if lm80_read_value() fails, it returns a negative error number which is stored to data->fan[f_min] and will be further used. We should avoid using the data if the read fails. The fix checks if lm80_read_value() fails, and if so, returns with the error number. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit c9c63915 ] If lm80_read_value() fails, it returns a negative number instead of the correct read data. Therefore, we should avoid using the data if it fails. The fix checks if lm80_read_value() fails, and if so, returns with the error number. Signed-off-by:
-
Stanislav Fomichev authored
[ Upstream commit 14541b1e ] Current libbfd feature test unconditionally links against -liberty and -lz. While it's required on some systems (e.g. opensuse), it's completely unnecessary on the others, where only -lbdf is sufficient (debian). This patch streamlines (and renames) the following feature checks: feature-libbfd - only link against -lbfd (debian), see commit 2cf90407 ("perf tools: Fix bfd dependency libraries detection") feature-libbfd-liberty - link against -lbfd and -liberty feature-libbfd-liberty-z - link against -lbfd, -liberty and -lz (opensuse), see commit 280e7c48 ("perf tools: fix BFD detection on opensuse") (feature-liberty{,-z} were renamed to feature-libbfd-liberty{,z} for clarity) The main motivation is to fix this feature test for bpftool which is currently broken on debian (libbfd feature shows OFF, but we still unconditionally link against -lbfd and it works). Tested on debian with only -lbfd installed (without -liberty); I'd appreciate if somebody on the other systems can test this new detection method. Signed-off-by:
Stanislav Fomichev <sdf@google.com> Acked-by:
-
Chris Perl authored
[ Upstream commit 594d1644 ] This patch removes the check from nfs_compare_mount_options to see if a `sec' option was passed for the current mount before comparing auth flavors and instead just always compares auth flavors. Consider the following scenario: You have a server with the address 192.168.1.1 and two exports /export/a and /export/b. The first export supports `sys' and `krb5' security, the second just `sys'. Assume you start with no mounts from the server. The following results in EIOs being returned as the kernel nfs client incorrectly thinks it can share the underlying `struct nfs_server's: $ mkdir /tmp/{a,b} $ sudo mount -t nfs -o vers=3,sec=krb5 192.168.1.1:/export/a /tmp/a $ sudo mount -t nfs -o vers=3 192.168.1.1:/export/b /tmp/b $ df >/dev/null df: ‘/tmp/b’: Input/output error Signed-off-by:
Chris Perl <cperl@janestreet.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Jim Mattson authored
[ Upstream commit 7a86dab8 ] Since the offset is added directly to the hva from the gfn_to_hva_cache, a negative offset could result in an out of bounds write. The existing BUG_ON only checks for addresses beyond the end of the gfn_to_hva_cache, not for addresses before the start of the gfn_to_hva_cache. Note that all current call sites have non-negative offsets. Fixes: 4ec6e863 ("kvm: Introduce kvm_write_guest_offset_cached()") Reported-by:
Cfir Cohen <cfir@google.com> Signed-off-by:
Jim Mattson <jmattson@google.com> Reviewed-by:
Peter Shier <pshier@google.com> Reviewed-by:
Krish Sadhukhan <krish.sadhukhan@oracle.com> Reviewed-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Mahesh Salgaonkar authored
[ Upstream commit 0db6896f ] For fadump to work successfully there should not be any holes in reserved memory ranges where kernel has asked firmware to move the content of old kernel memory in event of crash. Now that fadump uses CMA for reserved area, this memory area is now not protected from hot-remove operations unless it is cma allocated. Hence, fadump service can fail to re-register after the hot-remove operation, if hot-removed memory belongs to fadump reserved region. To avoid this make sure that memory from fadump reserved area is not hot-removable if fadump is registered. However, if user still wants to remove that memory, he can do so by manually stopping fadump service before hot-remove operation. Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
-
Vitaly Kuznetsov authored
[ Upstream commit e87555e5 ] AMD doesn't seem to implement MSR_IA32_MCG_EXT_CTL and svm code in kvm knows nothing about it, however, this MSR is among emulated_msrs and thus returned with KVM_GET_MSR_INDEX_LIST. The consequent KVM_GET_MSRS, of course, fails. Report the MSR as unsupported to not confuse userspace. Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by:
-
Martin Blumenstingl authored
[ Upstream commit 2b745ac3 ] The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N) only belong to the pin controller in the AO domain. With the current definition these pins cannot be referred to in .dts files as group (which is possible on GXBB and GXL for example). Add a separate "gpio_aobus" function to fix the mapping between the pin controller and the GPIO pins in the AO domain. This is similar to how the GXBB and GXL drivers implement this functionality. Fixes: 9dab1868 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Martin Blumenstingl authored
[ Upstream commit 42f9b48c ] The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N) only belong to the pin controller in the AO domain. With the current definition these pins cannot be referred to in .dts files as group (which is possible on GXBB and GXL for example). Add a separate "gpio_aobus" function to fix the mapping between the pin controller and the GPIO pins in the AO domain. This is similar to how the GXBB and GXL drivers implement this functionality. Fixes: 9dab1868 ("pinctrl: amlogic: Make driver independent from two-domain configuration") Signed-off-by:
-
Christophe Leroy authored
[ Upstream commit ffca395b ] On the 8xx, no-execute is set via PPP bits in the PTE. Therefore a no-exec fault generates DSISR_PROTFAULT error bits, not DSISR_NOEXEC_OR_G. This patch adds DSISR_PROTFAULT in the test mask. Fixes: d3ca5874 ("powerpc/mm: Fix reporting of kernel execute faults") Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
-
Noralf Trønnes authored
[ Upstream commit 2122b405 ] When unregistering fbdev using unregister_framebuffer(), any bound console will unbind automatically. This is working fine if this is the only framebuffer, resulting in a switch to the dummy console. However if there is a fb0 and I unregister fb1 having a bound console, I eventually get a crash. The fastest way for me to trigger the crash is to do a reboot, resulting in this splat: [ 76.478825] WARNING: CPU: 0 PID: 527 at linux/kernel/workqueue.c:1442 __queue_work+0x2d4/0x41c [ 76.478849] Modules linked in: raspberrypi_hwmon gpio_backlight backlight bcm2835_rng rng_core [last unloaded: tinydrm] [ 76.478916] CPU: 0 PID: 527 Comm: systemd-udevd Not tainted 4.20.0-rc4+ #4 [ 76.478933] Hardware name: BCM2835 [ 76.478949] Backtrace: [ 76.478995] [<c010d388>] (dump_backtrace) from [<c010d670>] (show_stack+0x20/0x24) [ 76.479022] r6:00000000 r5:c0bc73be r4:00000000 r3:6fb5bf81 [ 76.479060] [<c010d650>] (show_stack) from [<c08e82f4>] (dump_stack+0x20/0x28) [ 76.479102] [<c08e82d4>] (dump_stack) from [<c0120070>] (__warn+0xec/0x12c) [ 76.479134] [<c011ff84>] (__warn) from [<c01201e4>] (warn_slowpath_null+0x4c/0x58) [ 76.479165] r9:c0eb6944 r8:00000001 r7:c0e927f8 r6:c0bc73be r5:000005a2 r4:c0139e84 [ 76.479197] [<c0120198>] (warn_slowpath_null) from [<c0139e84>] (__queue_work+0x2d4/0x41c) [ 76.479222] r6:d7666a00 r5:c0e918ee r4:dbc4e700 [ 76.479251] [<c0139bb0>] (__queue_work) from [<c013a02c>] (queue_work_on+0x60/0x88) [ 76.479281] r10:c0496bf8 r9:00000100 r8:c0e92ae0 r7:00000001 r6:d9403700 r5:d7666a00 [ 76.479298] r4:20000113 [ 76.479348] [<c0139fcc>] (queue_work_on) from [<c0496c28>] (cursor_timer_handler+0x30/0x54) [ 76.479374] r7:d8a8fabc r6:c0e08088 r5:d8afdc5c r4:d8a8fabc [ 76.479413] [<c0496bf8>] (cursor_timer_handler) from [<c0178744>] (call_timer_fn+0x100/0x230) [ 76.479435] r4:c0e9192f r3:d758a340 [ 76.479465] [<c0178644>] (call_timer_fn) from [<c0178980>] (expire_timers+0x10c/0x12c) [ 76.479495] r10:40000000 r9:c0e9192f r8:c0e92ae0 r7:d8afdccc r6:c0e19280 r5:c0496bf8 [ 76.479513] r4:d8a8fabc [ 76.479541] [<c0178874>] (expire_timers) from [<c0179630>] (run_timer_softirq+0xa8/0x184) [ 76.479570] r9:00000001 r8:c0e19280 r7:00000000 r6:c0e08088 r5:c0e1a3e0 r4:c0e19280 [ 76.479603] [<c0179588>] (run_timer_softirq) from [<c0102404>] (__do_softirq+0x1ac/0x3fc) [ 76.479632] r10:c0e91680 r9:d8afc020 r8:0000000a r7:00000100 r6:00000001 r5:00000002 [ 76.479650] r4:c0eb65ec [ 76.479686] [<c0102258>] (__do_softirq) from [<c0124d10>] (irq_exit+0xe8/0x168) [ 76.479716] r10:d8d1a9b0 r9:d8afc000 r8:00000001 r7:d949c000 r6:00000000 r5:c0e8b3f0 [ 76.479734] r4:00000000 [ 76.479764] [<c0124c28>] (irq_exit) from [<c016b72c>] (__handle_domain_irq+0x94/0xb0) [ 76.479793] [<c016b698>] (__handle_domain_irq) from [<c01021dc>] (bcm2835_handle_irq+0x3c/0x48) [ 76.479823] r8:d8afdebc r7:d8afddfc r6:ffffffff r5:c0e089f8 r4:d8afddc8 r3:d8afddc8 [ 76.479851] [<c01021a0>] (bcm2835_handle_irq) from [<c01019f0>] (__irq_svc+0x70/0x98) The problem is in the console rebinding in fbcon_fb_unbind(). It uses the virtual console index as the new framebuffer index to bind the console(s) to. The correct way is to use the con2fb_map lookup table to find the framebuffer index. Fixes: cfafca80 ("fbdev: fbcon: console unregistration from unregister_framebuffer") Signed-off-by:
Noralf Trønnes <noralf@tronnes.org> Reviewed-by:
Mikulas Patocka <mpatocka@redhat.com> Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Lenny Szubowicz authored
[ Upstream commit 98cff8b2 ] In __ghes_panic() clear the block status in the APEI generic error status block for that generic hardware error source before calling panic() to prevent a second panic() in the crash kernel for exactly the same fatal error. Otherwise ghes_probe(), running in the crash kernel, would see an unhandled error in the APEI generic error status block and panic again, thereby precluding any crash dump. Signed-off-by:
Lenny Szubowicz <lszubowi@redhat.com> Signed-off-by:
David Arcari <darcari@redhat.com> Tested-by:
Tyler Baicar <baicar.tyler@gmail.com> Acked-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Kai-Heng Feng authored
[ Upstream commit 1fb3a7a7 ] I210 ethernet card doesn't wakeup when a cable gets plugged. It's because its PME is not set. Since commit 42eca230 ("PCI: Don't touch card regs after runtime suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops calling pci_finish_runtime_suspend(), which enables the PCI PME. To fix the issue, let's not to save PCI states when it's runtime suspend, to let the PCI subsystem enables PME. Fixes: 42eca230 ("PCI: Don't touch card regs after runtime suspend D3") Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Young Xiao authored
[ Upstream commit eec90376 ] If ice driver has q_vectors w/ active NAPI that has no rings, then this will result in a divide by zero error. To correct it I am updating the driver code so that we only support NAPI on q_vectors that have 1 or more rings allocated to them. See commit 13a8cd19 ("i40e: Do not enable NAPI on q_vectors that have no rings") for detail. Signed-off-by:
Young Xiao <YangX92@hotmail.com> Acked-by:
Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
-
Konstantin Khorenko authored
[ Upstream commit 31389b53 ] Out of bound read reported by KASan. i40iw_net_event() reads unconditionally 16 bytes from neigh->primary_key while the memory allocated for "neighbour" struct is evaluated in neigh_alloc() as tbl->entry_size + dev->neigh_priv_len where "dev" is a net_device. But the driver does not setup dev->neigh_priv_len and we read beyond the neigh entry allocated memory, so the patch in the next mail fixes this. Signed-off-by:
Konstantin Khorenko <khorenko@virtuozzo.com> Tested-by:
-
Peter Rosin authored
[ Upstream commit f75df8d4 ] Blitting an image with "negative" offsets is not working since there is no clipping. It hopefully just crashes. For the bootup logo, there is protection so that blitting does not happen as the image is drawn further and further to the right (ROTATE_UR) or further and further down (ROTATE_CW). There is however no protection when drawing in the opposite directions (ROTATE_UD and ROTATE_CCW). Add back this protection. The regression is 20-odd years old but the mindless warning-killing mentality displayed in commit 34bdb666 ("fbdev: fbmem: remove positive test on unsigned values") is also to blame, methinks. Fixes: 448d4797 ("fbdev: fb_do_show_logo() updates") Signed-off-by:
Peter Rosin <peda@axentia.se> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Fabian Frederick <ffrederick@users.sourceforge.net> Cc: Geert Uytterhoeven <geert+renesas@glider.be> cc: Geoff Levand <geoff@infradead.org> Cc: James Simmons <jsimmons@users.sf.net> Signed-off-by:
-
Guoqing Jiang authored
[ Upstream commit e820d55c ] When both regular IO and resync IO happen at the same time, and if we also need to split regular. Then we can see tasks hang due to barrier. 1. resync thread [ 1463.757205] INFO: task md1_resync:5215 blocked for more than 480 seconds. [ 1463.757207] Not tainted 4.19.5-1-default #1 [ 1463.757209] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1463.757212] md1_resync D 0 5215 2 0x80000000 [ 1463.757216] Call Trace: [ 1463.757223] ? __schedule+0x29a/0x880 [ 1463.757231] ? raise_barrier+0x8d/0x140 [raid10] [ 1463.757236] schedule+0x78/0x110 [ 1463.757243] raise_barrier+0x8d/0x140 [raid10] [ 1463.757248] ? wait_woken+0x80/0x80 [ 1463.757257] raid10_sync_request+0x1f6/0x1e30 [raid10] [ 1463.757265] ? _raw_spin_unlock_irq+0x22/0x40 [ 1463.757284] ? is_mddev_idle+0x125/0x137 [md_mod] [ 1463.757302] md_do_sync.cold.78+0x404/0x969 [md_mod] [ 1463.757311] ? wait_woken+0x80/0x80 [ 1463.757336] ? md_rdev_init+0xb0/0xb0 [md_mod] [ 1463.757351] md_thread+0xe9/0x140 [md_mod] [ 1463.757358] ? _raw_spin_unlock_irqrestore+0x2e/0x60 [ 1463.757364] ? __kthread_parkme+0x4c/0x70 [ 1463.757369] kthread+0x112/0x130 [ 1463.757374] ? kthread_create_worker_on_cpu+0x40/0x40 [ 1463.757380] ret_from_fork+0x3a/0x50 2. regular IO [ 1463.760679] INFO: task kworker/0:8:5367 blocked for more than 480 seconds. [ 1463.760683] Not tainted 4.19.5-1-default #1 [ 1463.760684] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1463.760687] kworker/0:8 D 0 5367 2 0x80000000 [ 1463.760718] Workqueue: md submit_flushes [md_mod] [ 1463.760721] Call Trace: [ 1463.760731] ? __schedule+0x29a/0x880 [ 1463.760741] ? wait_barrier+0xdd/0x170 [raid10] [ 1463.760746] schedule+0x78/0x110 [ 1463.760753] wait_barrier+0xdd/0x170 [raid10] [ 1463.760761] ? wait_woken+0x80/0x80 [ 1463.760768] raid10_write_request+0xf2/0x900 [raid10] [ 1463.760774] ? wait_woken+0x80/0x80 [ 1463.760778] ? mempool_alloc+0x55/0x160 [ 1463.760795] ? md_write_start+0xa9/0x270 [md_mod] [ 1463.760801] ? try_to_wake_up+0x44/0x470 [ 1463.760810] raid10_make_request+0xc1/0x120 [raid10] [ 1463.760816] ? wait_woken+0x80/0x80 [ 1463.760831] md_handle_request+0x121/0x190 [md_mod] [ 1463.760851] md_make_request+0x78/0x190 [md_mod] [ 1463.760860] generic_make_request+0x1c6/0x470 [ 1463.760870] raid10_write_request+0x77a/0x900 [raid10] [ 1463.760875] ? wait_woken+0x80/0x80 [ 1463.760879] ? mempool_alloc+0x55/0x160 [ 1463.760895] ? md_write_start+0xa9/0x270 [md_mod] [ 1463.760904] raid10_make_request+0xc1/0x120 [raid10] [ 1463.760910] ? wait_woken+0x80/0x80 [ 1463.760926] md_handle_request+0x121/0x190 [md_mod] [ 1463.760931] ? _raw_spin_unlock_irq+0x22/0x40 [ 1463.760936] ? finish_task_switch+0x74/0x260 [ 1463.760954] submit_flushes+0x21/0x40 [md_mod] So resync io is waiting for regular write io to complete to decrease nr_pending (conf->barrier++ is called before waiting). The regular write io splits another bio after call wait_barrier which call nr_pending++, then the splitted bio would continue with raid10_write_request -> wait_barrier, so the splitted bio has to wait for barrier to be zero, then deadlock happens as follows. resync io regular io raise_barrier wait_barrier generic_make_request wait_barrier To resolve the issue, we need to call allow_barrier to decrease nr_pending before generic_make_request since regular IO is not issued to underlying devices, and wait_barrier is called again to ensure no internal IO happening. Fixes: fc9977dd ("md/raid10: simplify the splitting of requests.") Reported-and-tested-by:
Siniša Bandin <sinisa@4net.rs> Signed-off-by:
Guoqing Jiang <gqjiang@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Alexey Khoroshilov authored
[ Upstream commit fdac7513 ] clps711x_fb_probe() increments refcnt of disp device node by of_parse_phandle() and leaves it undecremented on both successful and error paths. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
-
Wenjing Liu authored
[ Upstream commit 99b922f9 ] [why] Some dongle doesn't have a valid extended dongle caps, but we still set the extended dongle caps to be valid. This causes validation fails for all timing. [how] If no dp_hdmi_max_pixel_clk is provided, don't use extended dongle caps. Signed-off-by:
Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by:
Aric Cyr <Aric.Cyr@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
Abdoulaye Berthe <Abdoulaye.Berthe@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit a52c5a16 ] There are several warnings from Clang about no case statement matching the constant 0: In file included from drivers/block/drbd/drbd_receiver.c:48: In file included from drivers/block/drbd/drbd_int.h:48: In file included from ./include/linux/drbd_genl_api.h:54: In file included from ./include/linux/genl_magic_struct.h:236: ./include/linux/drbd_genl.h:321:1: warning: no case matching constant switch condition '0' GENL_struct(DRBD_NLA_HELPER, 24, drbd_helper_info, ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ./include/linux/genl_magic_struct.h:220:10: note: expanded from macro 'GENL_struct' switch (0) { ^ Silence this warning by adding a 'case 0:' statement. Additionally, adjust the alignment of the statements in the ct_assert_unique macro to avoid a checkpatch warning. This solution was originally sent by Arnd Bergmann with a default case statement: https://lore.kernel.org/patchwork/patch/756723/ Link: https://github.com/ClangBuiltLinux/linux/issues/43Suggested-by:
Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Lars Ellenberg authored
[ Upstream commit 9848b6dd ] If you try to promote a Secondary while connected to a Primary and allow-two-primaries is NOT set, we will wait for "ping-timeout" to give this node a chance to detect a dead primary, in case the cluster manager noticed faster than we did. But if we then are *still* connected to a Primary, we fail (after an additional timeout of ping-timout). This change skips the spurious second timeout. Most people won't notice really, since "ping-timeout" by default is half a second. But in some installations, ping-timeout may be 10 or 20 seconds or more, and spuriously delaying the error return becomes annoying. Signed-off-by:
-
Lars Ellenberg authored
[ Upstream commit b17b5960 ] With "on-no-data-accessible suspend-io", DRBD requires the next attach or connect to be to the very same data generation uuid tag it lost last. If we first lost connection to the peer, then later lost connection to our own disk, we would usually refuse to re-connect to the peer, because it presents the wrong data set. However, if the peer first connects without a disk, and then attached its disk, we accepted that same wrong data set, which would be "unexpected" by any user of that DRBD and cause "undefined results" (read: very likely data corruption). The fix is to forcefully disconnect as soon as we notice that the peer attached to the "wrong" dataset. Signed-off-by:
-
