Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200415062154.741179-3-bjorn.andersson@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add coresight components found on Qualcomm SC7180 SoC.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/73e4352c19afff4c9ea2041b263a85e68e6eef11.1586263250.git.saiprakash.ranjan@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This was mistakenly copied from the downstream dts, however the upstream
driver works differently.

I only tested this with the pm8150_gpios node (used with volume button),
but the 2 others should be the same.

Fixes: e92b61c8 ("arm64: dts: qcom: pm8150l: Add base dts file")
Fixes: 229d5bca ("arm64: dts: qcom: pm8150b: Add base dts file")
Fixes: 5101f22a ("arm64: dts: qcom: pm8150: Add base dts file")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200420153543.14512-1-jonathan@marek.caSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Overriding the QUSB2 V2 Phy tuning parameters for SC7180 IDP device.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1583747589-17267-10-git-send-email-sanm@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Use generic QUSB2 V2 Phy configuration for SC7180.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1583747589-17267-8-git-send-email-sanm@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Use generic QUSB2 V2 Phy configuration for sdm845.
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1583747589-17267-9-git-send-email-sanm@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add device bindings for cpuidle states for cpu devices.

Cc: devicetree@vger.kernel.orgi
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Srinivas Rao L <lsrao@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1586703004-13674-2-git-send-email-mkshah@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This patch re-arranges ipq8074 device nodes based on node address
followed by node names followed by node labels.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1586572830-22727-1-git-send-email-sivaprak@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add the interconnect path configuration for the venus video codec of
the SC7180.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20200409160206.1.Icf877f5cd50ef5e56d14ee014ca196d76242cb89@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Changed polling-delay and polling-delay-passive to zero to disable
polling mode of the framework as interrupts for tsens are already
configured.
Signed-off-by: Rajeshwari <rkambl@codeaurora.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1586244677-14399-1-git-send-email-rkambl@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Devices are supposed to be sorted by unit address.  These two got
swapped when they landed.  Fix.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200331092832.1.Ic361058ca22d7439164ffea11421740462e14272@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.

arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu4-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu5-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu6-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cpu7-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust0-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
clust1-mhm-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
wlan-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8998-mtp.dt.yaml: thermal-zones:
multimedia-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/cd6f0c7298437d35642b35c9ede9064c247d6090.1585562459.git.amit.kucheria@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.

arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-ifc6640.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu0-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu1-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu2-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cpu3-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
m4m-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
l3-or-venus-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster0-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
cluster1-l2-thermal:trips: 'trip-point@0' does not match any of the
regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
q6-dsp-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
mem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8096-db820c.dt.yaml: thermal-zones:
modemtx-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2c0aa5357c96c3caff8554f9ef3ab9c5a2b8d2f8.1585562459.git.amit.kucheria@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The thermal trip points have unit name but no reg property, so we can
remove them. It also fixes the following warnings from 'make dtbs_check'
after adding the thermal yaml bindings.

arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/apq8016-sbc.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'

arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
gpu-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
camera-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
arch/arm64/boot/dts/qcom/msm8916-mtp.dt.yaml: thermal-zones:
modem-thermal:trips: 'trip-point@0' does not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2d3d045c18a2fb85b28cf304aa11ae6e6538d75e.1585562459.git.amit.kucheria@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add DISP_CC_MDSS_ROT_CLK and DISP_CC_MDSS_AHB_CLK
in the assigned clocks list as these are display
specific clocks and needs to be initialized from
the client side. Adding the default rate of
19.2 mhz for these clocks for sc7180 target.
Signed-off-by: Krishna Manikandan <mkrishn@codeaurora.org>
Link: https://lore.kernel.org/r/1584709864-5587-1-git-send-email-mkrishn@codeaurora.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Re-introduce the include of the sc7180 interconnect node name
definitions. Though this was part of v5 of the interconnect provider
series [1], it was dropped because the DT changes went through a
different tree than the header. Re-add that now.

Interconnect clients being introduced can reference this patch as a
dependency, rather than racing each other to add the include.

[1] https://patchwork.kernel.org/patch/11417989/Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200310161502.1.Ia2884ed3c8826f52fbd5dcfa7a376a2fac4f31e6@changeidSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Enable the ov8856 main camera and the ov7251 b/w tracking camera
used on the Qualcomm RB3 kit.

Currently the camera nodes have not yet been attached to an to a
CSI2 endpoint, since no driver currently supports the ISP that the the
SDM845/db845c ships with.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-6-robert.foss@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add pm_8998 GPIO trace names. These names are defined in
the 96boards db845c mezzanine schematic.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-5-robert.foss@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The sdm845 SOC ships with a CCI controller, which
has two CCI/I2C buses.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-4-robert.foss@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add cci device to msm8916.dtsi.
Add default 96boards camera node for db410c (apq8016-sbc).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-3-robert.foss@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The msm8916 CCI controller provides one CCI/I2C bus.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200324155843.10719-2-robert.foss@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This patch enables the primary and secondary USB controllers on the
qcs404-evb.

Primary:
The primary USB controller has

- One USB3 SS PHY using gpio-usb-conn
- One USB2 HS PHY in device mode only and no connector driver
  associated.

Secondary:
The second DWC3 controller which has one USB Hi-Speed PHY attached to it.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-7-bryan.odonoghue@linaro.org
[bjorn: Dropped usb3 role switching and enabled vbus]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Rather than set the minimum microvolt for this regulator in the USB SS PHY
driver, set it in the DTS.
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-6-bryan.odonoghue@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

VBUS is supplied by an external regulator controlled by a GPIO pin. This
patch models the regulator as regulator-usb3-vbus.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-5-bryan.odonoghue@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

The USB ID pin is used to tell if a system is a Host or a Device. For our
purposes we will bind this pin into gpio-usb-conn later.

For now define the pin with its pinmux.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-4-bryan.odonoghue@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Defines VBUS detect and VBUS boost for the QCS404 EVB.

Detect:
VBUS present/absent is presented to the SoC via a GPIO on the EVB. Define
the pin mapping for later use by gpio-usb-conn.

Boost:
An external regulator is used to trigger VBUS on/off via GPIO. This patch
defines the relevant GPIO in the EVB dts.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-3-bryan.odonoghue@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

QCS404 sports HS and SS USB controllers based on dwc3 block with two HS
PHYs and one SS PHY. Add nodes for these devices and enable them for
EVB board.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200311191517.8221-2-bryan.odonoghue@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

"arm,armv8" compatible should only be used for software models. Replace
it with the real cpu type.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/2526d2b2907116d1bb6f7edd194226eb7e24c333.1584516925.git.amit.kucheria@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Kryo468 is found in sc7180, so add it to the list of cpu compatibles
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/cd0f3d35ca0fc2944fd97e030a28318ff82dd5c1.1584516925.git.amit.kucheria@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Subnodes for PSCI should start with "power-domain-", so let's adopt to
this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200326103932.5809-3-ulf.hansson@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

As the domain-idle-state DT binding got converted to the json-schema, a few
minor changes were introduced. For example, the states needs to be
specified within a separate node, named domain-idle-states. Let's conform
to the updated binding.

This also silence the below errors for msm8916 from of 'make dtbs_check':
idle-states: cluster-retention:compatible:0: 'arm,idle-state' was expected
idle-states: cluster-gdhs:compatible:0: 'arm,idle-state' was expected
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20200326103932.5809-2-ulf.hansson@linaro.orgSigned-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This sorts the actual field names too, potentially causing even more
chaos and confusion at merge time if you have edited the MAINTAINERS
file.  But the end result is a more consistent layout, and hopefully
it's a one-time pain minimized by doing this just before the -rc1
release.

This was entirely scripted:

  ./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

They are all supposed to be sorted, but people who add new entries don't
always know the alphabet.  Plus sometimes the entry names get edited,
and people don't then re-order the entry.

Let's see how painful this will be for merging purposes (the MAINTAINERS
file is often edited in various different trees), but Joe claims there's
relatively few patches in -next that touch this, and doing it just
before -rc1 is likely the best time.  Fingers crossed.

This was scripted with

  /scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS

but then I also ended up manually upper-casing a few entry names that
stood out when looking at the end result.
Requested-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Thomas Gleixner:
 "A set of three patches to fix the fallout of the newly added split
  lock detection feature.

  It addressed the case where a KVM guest triggers a split lock #AC and
  KVM reinjects it into the guest which is not prepared to handle it.

  Add proper sanity checks which prevent the unconditional injection
  into the guest and handles the #AC on the host side in the same way as
  user space detections are handled. Depending on the detection mode it
  either warns and disables detection for the task or kills the task if
  the mode is set to fatal"

* tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest
  KVM: x86: Emulate split-lock access as a write in emulator
  x86/split_lock: Provide handle_guest_split_lock()

Pull time(keeping) updates from Thomas Gleixner:

 - Fix the time_for_children symlink in /proc/$PID/ so it properly
   reflects that it part of the 'time' namespace

 - Add the missing userns limit for the allowed number of time
   namespaces, which was half defined but the actual array member was
   not added. This went unnoticed as the array has an exessive empty
   member at the end but introduced a user visible regression as the
   output was corrupted.

 - Prevent further silent ucount corruption by adding a BUILD_BUG_ON()
   to catch half updated data.

* tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ucount: Make sure ucounts in /proc/sys/user don't regress again
  time/namespace: Add max_time_namespaces ucount
  time/namespace: Fix time_for_children symlink

Pull scheduler fixes/updates from Thomas Gleixner:

 - Deduplicate the average computations in the scheduler core and the
   fair class code.

 - Fix a raise between runtime distribution and assignement which can
   cause exceeding the quota by up to 70%.

 - Prevent negative results in the imbalanace calculation

 - Remove a stale warning in the workqueue code which can be triggered
   since the call site was moved out of preempt disabled code. It's a
   false positive.

 - Deduplicate the print macros for procfs

 - Add the ucmap values to the SCHED_DEBUG procfs output for completness

* tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Add task uclamp values to SCHED_DEBUG procfs
  sched/debug: Factor out printing formats into common macros
  sched/debug: Remove redundant macro define
  sched/core: Remove unused rq::last_load_update_tick
  workqueue: Remove the warning in wq_worker_sleeping()
  sched/fair: Fix negative imbalance in imbalance calculation
  sched/fair: Fix race between runtime distribution and assignment
  sched/fair: Align rq->avg_idle and rq->avg_scan_cost

Pull perf fixes from Thomas Gleixner:
 "Three fixes/updates for perf:

   - Fix the perf event cgroup tracking which tries to track the cgroup
     even for disabled events.

   - Add Ice Lake server support for uncore events

   - Disable pagefaults when retrieving the physical address in the
     sampling code"

* tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Disable page faults when getting phys address
  perf/x86/intel/uncore: Add Ice Lake server uncore support
  perf/cgroup: Correct indirection in perf_less_group_idx()
  perf/core: Fix event cgroup tracking

Pull locking fixes from Thomas Gleixner:
 "Three small fixes/updates for the locking core code:

   - Plug a task struct reference leak in the percpu rswem
     implementation.

   - Document the refcount interaction with PID_MAX_LIMIT

   - Improve the 'invalid wait context' data dump in lockdep so it
     contains all information which is required to decode the problem"

* tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Improve 'invalid wait context' splat
  locking/refcount: Document interaction with PID_MAX_LIMIT
  locking/percpu-rwsem: Fix a task_struct refcount

Pull cifs fixes from Steve French:
 "Ten cifs/smb fixes:

   - five RDMA (smbdirect) related fixes

   - add experimental support for swap over SMB3 mounts

   - also a fix which improves performance of signed connections"

* tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: enable swap on SMB3 mounts
  smb3: change noisy error message to FYI
  smb3: smbdirect support can be configured by default
  cifs: smbd: Do not schedule work to send immediate packet on every receive
  cifs: smbd: Properly process errors on ib_post_send
  cifs: Allocate crypto structures on the fly for calculating signatures of incoming packets
  cifs: smbd: Update receive credits before sending and deal with credits roll back on failure before sending
  cifs: smbd: Check send queue size before posting a send
  cifs: smbd: Merge code to track pending packets
  cifs: ignore cached share root handle closing errors