Enable sparse warnings about endianness, replace the remaining fields
regarding network operations without explicit endianness annotations
with such that are annotated, and propagate this through the entire
stack.

Uses of ieee802154_addr_sa are not changed yet, this patch is only
concerned with all other fields (such as address filters, operation
parameters and the likes).
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a replacement ieee802154_addr struct with proper endianness on
fields. Short address fields are stored as __le16 as on the network,
extended (EUI64) addresses are __le64 as opposed to the u8[8] format
used previously. This disconnect with the netdev address, which is
stored as big-endian u8[8], is intentional.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The struct as currently defined uses host byte order for some fields,
and most big endian/EUI display byte order for other fields. Inside the
stack, endianness should ideally match network byte order where possible
to minimize the number of byteswaps done in critical paths, but this
patch does not address this; it is only preparatory.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

most of these are only used locally, make them static.
fold lowpan_expire_frag_queue into its caller, its small enough.

Cc: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the sh_eth device is registered using OF, then the driver
should call of_mdiobus_register() to register the PHYs described
in the devicetree and then use of_phy_connect() to connect the
PHYs to the device.

This ensures that any PHYs registered in the device tree are
appropriately connected to the parent devices nodes so that
the PHY drivers can access their OF properties.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

nla_nest_end() already has return skb->len, so replace
return skb->len with return nla_nest_end instead().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcm_enet_netpoll does not exist, and causing
bcm63xx_net to fail to build when NET_POLL_CONTROLLER
is defined.

Remove the bogus .ndo_poll_controller = bcm_enet_netpoll
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric W. Biederman says:

====================
Don't receive packets when the napi budget == 0

To the best of understanding processing any received packets when the
napi budget == 0 is broken driver behavior.  At the same time I don't
think we have ever cared before so there are a handful of drivers that
need fixes.

I care now as I will shortly be using htis in netpoll to get the
tx queue processing without the rx queue processing.

Drivers that need fixes are few and far between, and so far I have only
found two of them.  More similar patches later if I find more drivers
that need fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.

This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

consolidate duplicate code is skb_checksum_setup() helpers

Realizing that the skb_maybe_pull_tail() calls in the IP-protocol
specific portions of both helpers are terminal ones (i.e. no further
pulls are expected), their maximum size to be pulled can be made match
their minimal size needed, thus making the code identical and hence
possible to be moved into another helper.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb, e1000e, ixgbe and ixgbevf.

Tom Herbert provides changes to e1000e, igb and ixgbe to call skb_set_hash()
to set the hash and its type in an skbuff.

Carolyn provides a fix for igb where using ethtool for EEE settings, which
was not working correctly.

Jacob provides some trivial cleanups and fixes for ixgbe which mainly
dealt with the file headers.

Julia Lawall provides a one fix for ixgbevf where the driver did not need
to adjust the power state on suspend, so the call to pci_set_power_state()
in the resume function was a no-op.

v2:
- dropped patches 4-6 from original series which implemented debugfs for
  igb from Carolyn based on feed back from David Miller and Or Gerlitz
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
For the mac80211 bits, Johannes says:

"This time, I have a number of small fixes and improvements, and those
are fairly straight-forward. More interesting changes come from Luca
with some preparations for the CSA work, mostly around interface/channel
combinations checking. One other possibly interesting change is a small
one by myself to add NAPI support back to mac80211, which can help
improve TCP behaviour through GRO."

For the Bluetooth bits, Gustavo says:

"This is our first pull request for 3.15, the main feature here is the addition of
the privacy feature for low energy devices. Other than that we have a bunch of small
improvements, fixes, and clean ups all over the tree."

And...

"Another pull request to 3.15. Here we have the second part of the LE private
feature, the LE auto-connect feature and improvements to the power off
procedures. The rest are small improvements, clean up, and fixes."

For the iwlwifi bits, Emmanuel says:

"I have here a whole bunch of various things. Trivial cleanups,
debugfs handlers and new stuff for the new generation of devices
along with new capabilities for monitor mode. We also have support
for power save for dual interface mode, but that is not supported by
the firmware currently available."

And for the Atheros bits, Kalle says:

"For ath10k Alexander did some cleanup to PCI error cases and switched
ath10k to use pci_enable_msi_range(). Michal implemented AP CSA support
and sta_rc_update() operation. I enabled firmware "STA quick kickout"
functionality for faster detection of disappeared clients.

Also there are lots of small fixes to everywhere from various people."

I pulled the wireless tree to avoid some merge conflicts, and I
reverted the staging patch that I had mistakenly merged previously.
Along with that, mwifiex, brcmfmac, wil6210, ath9k, and a few other
drivers get their usual round of updates.  Also notable is the addition
of yet another driver in the rtlwifi family.

 ...

I have amended this commit request to correct the build problems in
staging, including a warning added to one of the staging drivers by
the wireless-next tree.  I also included a fix from Larry Finger to
address an issue found in rtl8723be by Dan Carpenter and smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
Misc. fixes for cxgb4

This patch series provides miscelleneous fixes for Chelsio T4/T5 adapters
cxgb4 driver related to SGE and MTU.

Also fixes regression in LSO calcuation path.
("cxgb4: Calculate len properly for LSO path")

The patches series is created against David Miller's 'net-next' tree.
And includes patches on cxgb4 driver.

We would like to request this patch series to get merged via David Miller's
'net-next' tree.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 0034b298 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
introduced a regression where-in length was calculated wrongly for LSO path,
causing chip hangs.
So, correct the calculation of len.

Fixes: 0034b298 ("cxgb4: Don't assume LSO only uses SGL path in t4_eth_xmit()")
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'd come in with SGE_FL_BUFFER_SIZE[0] and [1] both equal to 64KB and the
extant logic would flag that as an error.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/ath/ath9k/recv.c

Commit a619d1ab leads to the following static checker warning:

drivers/net/wireless/rtlwifi/rtl8723be/phy.c:667 _rtl8723be_store_tx_power_by_rate()
error: buffer overflow 'rtlphy->tx_power_by_rate_offset[band]' 4 <= 5

This warning arises because the code is testing the indices for the wrong maximum
values. In addition, the tests merely putput a warning, and then procedes to
corrupt memory. With this change, any such invalid memory access is avoided.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 3ebe8e25 ("ieee80211: remove function
ieee80211_{dsss_chan_to_freq, freq_to_dsss_chan}") removed
ieee80211_dsss_chan_to_freq, but it neglected to account for this
staging driver...

Cc: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit d8ca16db ("mac80211: add length check in
ieee80211_is_robust_mgmt_frame()") changed that API to take an skb,
and added "_ieee80211_is_robust_mgmt_frame" as a direct replacement
for the older API.  This is the same fix that was applied to the other
rtlwifi drivers in that commit.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is basically just to let Coverity et al shut up. Remove an
unneeded NULL check in sctp_assoc_update_retran_path().

It is safe to remove it, because in sctp_assoc_update_retran_path()
we iterate over the list of transports, our own transport which is
asoc->peer.retran_path included. In the iteration, we skip the
list head element and transports in state SCTP_UNCONFIRMED.

Such transports came from peer addresses received in INIT/INIT-ACK
address parameters. They are not yet confirmed by a heartbeat and
not available for data transfers.

We know however that in the list of transports, even if it contains
such elements, it at least contains our asoc->peer.retran_path as
well, so even if next to that element, we only encounter
SCTP_UNCONFIRMED transports, we are always going to fall back to
asoc->peer.retran_path through sctp_trans_elect_best(), as that is
for sure not SCTP_UNCONFIRMED as per fbdf501c ("sctp: Do no
select unconfirmed transports for retransmissions").

Whenever we call sctp_trans_elect_best() it will give us a non-NULL
element back, and therefore when we break out of the loop, we are
guaranteed to have a non-NULL transport pointer, and can remove
the NULL check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 161d7855.

Reversal of fortune -- I thought this was going to be resolved by other
means, but that hasn't materialized.  Plus, apparently we now care more
than I realized about not breaking staging drivers...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This driver does not need to adjust the power state on suspend, so the
call to pci_set_power_state in the resume function is a no-op.  Drop it,
to make the code more understandable.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes some formatting on multilined print messages, so that
the text of the print appears on a single line, which aids in grepping
the sourcecode for where the error came from.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The header above this function did not match the function prototype.
This patch rewords the comment to specify the correct parameters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the contact information on the ixgbe driver files so
that every file includes the Linux NICS address, as it is still used,
but only a few of the files mentioned it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

cppcheck detected following warning in ixgbe_fcoe.c
(warning) %d in format string (no. 1) requires 'int' but the
argument type is 'unsigned int'.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where using ethtool for EEE setting was not
working correctly.  This patch also fixes a problem where
the function that checks for EEE status on i354 devices was not being
called and was causing warnings with static analysis tools.
Reported-by: Rashika Kheria <rashika.kheria@gmail.com>
Reported-by: Josh Triplett <josh@joshtriplett.org>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Eric W. Biederman says:

====================
Using dev_kfree_skb_any for functions called in multiple contexts

This patchset should be an uncontroversial set of changes to change
dev_kfree_skb to dev_kfree_skb_any for code paths that are called in
hard irq contexts in addition to other contexts.  netpoll is the reason
this code gets called in multiple contexts.

There is more coming but these changes are a good starting place, and
stand on their own.

Since the last round changes to the rx path have been removed netpoll
will changed to avoid that.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>

netpoll can call functions in hard irq context that are ordinarily
called in lesser contexts.  For those functions use dev_kfree_skb_any
and dev_consume_skb_any so skbs are freed safely from hard irq
context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace free_skb with dev_kfree_skb_any in be_tx_compl_process as
which can be called in hard irq by netpoll, softirq context
by normal napi polling, and in normal sleepable context
by the network device close method.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>