Add support for MCB over PCI devices. Both PCI attached on-board Chameleon FPGAs
as well as CompactPCI based MCB carrier cards are supported with this driver.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The MCB (MEN Chameleon Bus) is a Bus specific to MEN Mikroelektronik
FPGA based devices. It is used to identify MCB based IP-Cores within
an FPGA and provide the necessary framework for instantiating drivers
for these devices.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove firmware framebuffer before initializing hyperv-fb.  Needed
on gen2 virtual machines.   Letting register_framebuffer handle the
switchover results in efifb still being active while hyperv graphics
are initialized, which in turn can make the linux kernel hang.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

UEFI-based generation 2 virtual machines support vmbus devices only.
There is no pci bus.  Thus they use a different mechanism for the
graphics framebuffer:  Instead of using the vga pci bar a chunk of
memory muct be allocated from the hyperv mmio region declared using
APCI.  This patch implements support for it.

Based on a patch by Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This implements support for defining reserved areas as subnodes,
to keep the genpool from using these.
Suggested-by: Rob Herring <robherring2@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some SoCs need parts of their sram for special purposes. So while being part
of the peripheral, it should not be part of the genpool controlling the sram.

Therefore add the option to define reserved regions as subnodes of the
sram-node similar to defining reserved global memory regions.

Originally
Suggested-by: Rob Herring <robherring2@gmail.com>

Using subnodes for reserved regions
Suggested-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d2ae2e20 ("driver/memory:Move
Freescale IFC driver to a common driver") introduces this build
regression into the mpc85xx_defconfig:

 drivers/built-in.o: In function `fsl_ifc_nand_remove':
 drivers/mtd/nand/fsl_ifc_nand.c:1147: undefined reference to `fsl_ifc_ctrl_dev'
 drivers/mtd/nand/fsl_ifc_nand.c:1147: undefined reference to `fsl_ifc_ctrl_dev'
 drivers/built-in.o: In function `fsl_ifc_nand_probe':
 drivers/mtd/nand/fsl_ifc_nand.c:1031: undefined reference to `fsl_ifc_ctrl_dev'
 drivers/mtd/nand/fsl_ifc_nand.c:1031: undefined reference to `fsl_ifc_ctrl_dev'
 drivers/built-in.o: In function `match_bank':
 drivers/mtd/nand/fsl_ifc_nand.c:1013: undefined reference to `convert_ifc_address'
 drivers/built-in.o: In function `fsl_ifc_nand_probe':
 drivers/mtd/nand/fsl_ifc_nand.c:1059: undefined reference to `fsl_ifc_ctrl_dev'
 drivers/mtd/nand/fsl_ifc_nand.c:1080: undefined reference to `fsl_ifc_ctrl_dev'
 drivers/mtd/nand/fsl_ifc_nand.c:1069: undefined reference to `fsl_ifc_ctrl_dev'
 drivers/mtd/nand/fsl_ifc_nand.c:1069: undefined reference to `fsl_ifc_ctrl_dev'
 make: *** [vmlinux] Error 1

This happens because there is nothing to descend us into the
drivers/memory directory in the mpc85xx_defconfig.  It wasn't
selecting CONFIG_MEMORY.  So we never built drivers/memory/fsl_ifc.o
and so we have nothing to link the above symbols against.

Since the goal of the original commit was to relocate the driver to
an arch independent location, it only makes sense to relocate the
Kconfig setting there as well.  But that alone won't fix the build
failure; for that we ensure whoever selects FSL_IFC also selects MEMORY.

Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This helps increasing build testing coverage.
To do this, __raw_{read,write}b() functions was be replaced with
simple {read,write}b() variants.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

- Remove old and currently wrong address of the FSF from license
  parts of the code.
- Remove unused #include and sort remaining headers alphabetically.
- Remove unised definitions.
- Add definitions for bit-fields.
- Add missing module owner field.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fix mxc_w1_ds2_reset_bus() return value.
According to i.MX reference manual, "presence status" reflected
in the bit 6 of control register.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Configuration for masters and slaves is included only if W1 symbol
enabled, so no reason to check it once more.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy King <acking@vmware.com>
Cc: Dmitry Torokhov <dtor@vmware.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Harshavardhan R Kharche <harshavardhan.r.kharche@intel.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

While running Documentation/watchdog/src/watchdog-simple.c
and quiting by Ctrl-C, fallowing error is displayed:
mei_me 0000:00:16.0: wd: stop failed to complete ret=-512.

The whatchdog core framework is not able to propagate
-ESYSRESTART or -EINTR. Also There is no much sense in
restarting the close system call so instead of using
wait_event_interruptible_timeout we can use wait_event_timeout
with reasonable 10 msecs timeout.
Reported-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add reduce credits to wd_send to remove code
repetition and simplify error handling
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1. Propagate ENOTTY  to user space if the client is not present
in the system
2. Use ETIME consistently on timeouts
3. Return EIO on write failures
4. Return ENODEV on recoverable device failures such as resets
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since txe use doorbell and not circular buffer
we have to cheat in write slot counting, txe always consume all the
slots upon write. In order for it to work we need to track
slots using mei_hbuf_empty_slots() instead of tracking it in mei layer
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A client has to acquire host buffer
before writing, we add lock like wrapper
to replace the code snippet

if (dev->hbuf_is_ready)
        dev->hbuf_is_ready = false;
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This completes the show_sdb_tree functionality, with the
new informative fields.  The output for a verbose module is now
like this (long lines are unavoidable):

 SDB: 00000651:e6a542c9 WB4-Crossbar-GSI
 SDB: 0000ce42:00000601 WB-DMA.Control      (00001000-0000103f)
 SDB: 0000ce42:779c5443 WB-OneWire-Master   (00001100-000011ff)
 SDB: 0000ce42:00000603 WB-SPEC-CSR         (00001200-0000121f)
 SDB: 0000ce42:00000013 WB-VIC-Int.Control  (00001300-000013ff)
 SDB: 0000ce42:d5735ab4 WB-DMA.EIC          (00001400-0000140f)
 SDB: 00000651:eef0b198 WB4-Bridge-GSI      (bridge: 00002000)
 SDB:    00000651:e6a542c9 WB4-Crossbar-GSI
 SDB:    0000ce42:123c5443 WB-I2C-Master       (00003000-000030ff)
 SDB:    0000ce42:e503947e WB-SPI.Control      (00003100-0000311f)
 SDB:    0000ce42:123c5443 WB-I2C-Master       (00003200-000032ff)
 SDB:    0000ce42:00000608 WB-FMC-ADC-Core     (00003300-0000337f)
 SDB:    0000ce42:779c5443 WB-OneWire-Master   (00003400-000034ff)
 SDB:    0000ce42:26ec6086 WB-FMC-ADC.EIC      (00003500-0000350f)
 SDB:    0000ce42:00000604 WB-Timetag-Core     (00003600-0000367f)
 SDB: Synthesis repository: git://ohwr.org/fmc-projects/fmc-adc-100m14b4cha.git
 SDB: Bitstream 'spec_top_fmc_adcmc-projects/fmc-adc-100m14b4cha.git' \
         synthesized 20140116 by mcattin (ISE version 133), commit f0a539dffe6d
Signed-off-by: Tomasz Wlostowski <tomasz.wlostowski@cern.ch>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Juan David Gonzalez Cobas <dcobas@cern.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows easier modification to the eeprom than loading the
fmc-write-eeprom module.  The carrier driver will refuse writing if
the FPGA is not running the golden gateware image, so writing in
practice is only available at manufacture/development time.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Juan David Gonzalez Cobas <dcobas@cern.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To quote Mark:
	I think it's safe to delete the driver.

	The mimc200 unit is now basically obsolete and there'll be no
	new development on it.

Becides, it grabs the 0 misc minor number, when it never asked for it,
conflicting with the logitech bus mouse driver.

Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use a resource for the hyperv mmio region instead of start/size
variables.  Register the region properly so it shows up in
/proc/iomem.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want these fixes here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ARM SoC fixes from Olof Johansson:
 "A collection of fixes for ARM platforms.  Most are fixes for DTS
  files, mostly from DT conversion on OMAP which is still finding a few
  issues here and there.

  There's a couple of small stale code removal patches that we usually
  queue for the next release instead, but they seemed harmless enough to
  bring in now.

  Also, a fix for backlight on some PXA platforms, and a cache
  configuration fix for Tegra, etc"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
  MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
  ARM: tegra: only run PL310 init on systems with one
  ARM: tegra: Add head numbers to display controllers
  ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
  ARM: tegra: fix RTC0 alias for Cardhu
  ARM: dove: dt: revert PMU interrupt controller node
  Documentation: dt: OMAP: Update Overo/Tobi
  ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
  ARM: dts: omap3-tobi: Use the correct vendor prefix
  ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
  ARM: OMAP2+: Remove legacy macros for zoom platforms
  ARM: OMAP2+: Remove MACH_NOKIA_N800
  ARM: dts: N900: add missing compatible property
  ARM: dts: N9/N950: fix boot hang with 3.14-rc1
  ARM: OMAP1: nokia770: enable tahvo-usb
  ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
  ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
  ARM: dts: omap3-gta04: Fix mmc1 properties.
  ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
  ARM: OMAP2+: add missing ARCH_HAS_OPP
  ...

Pull regulator fixes from Mark Brown:
 "Mostly unexciting driver fixes, plus one fix to lower the severity of
  the log message when we don't use an optional regulator - the fixes
  for ACPI system made this come up more often and it was correctly
  observed that it was causing undue concern for users"

* tag 'regulator-v3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: max14577: Fix invalid return value on DT parse success
  regulator: core: Change dummy supplies error message to a warning
  regulator: s5m8767: Add missing of_node_put
  regulator: s5m8767: Use of_get_child_by_name
  regulator: da9063: Bug fix when setting max voltage on LDOs 5-11

Pull timer fix from Thomas Gleixner:
 "Serialize the registration of a new sched_clock in the currently ARM
  only generic sched_clock facilty to avoid sched_clock havoc"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched_clock: Prevent callers from seeing half-updated data

Pull x86 fixes from Thomas Gleixner:

 - a bugfix which prevents a divide by 0 panic when the newly introduced
   try_msr_calibrate_tsc() fails

 - enablement of the Baytrail platform to utilize the newfangled msr
   based calibration

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: tsc: Add missing Baytrail frequency to the table
  x86, tsc: Fallback to normal calibration if fast MSR calibration fails

Pull irq fixes from Thomas Gleixner:
 "Another four fixlets to tame the ARM orion irq chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: orion: Fix getting generic chip pointer.
  irqchip: orion: clear stale interrupts in irq_startup
  irqchip: orion: use handle_edge_irq on bridge irqs
  irqchip: orion: clear bridge cause register on init

Pull USB fixes from Greg KH:
 "Here are a number of USB fixes for reported issues for 3.14-rc4

  The majority of these are for USB gadget, phy, and musb driver issues.
  And there's a few new device ids thrown in for good measure"

* tag 'usb-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: need to mask when writting endptflush and endptprime
  usb: musb: correct use of schedule_delayed_work()
  usb: phy: msm: fix compilation errors when !CONFIG_PM_SLEEP
  usb: gadget: fix NULL pointer dereference
  usb: gadget: printer: using gadget_is_otg to check otg support at runtime
  phy: let phy_provider_register be the last step in registering PHY
  phy-core: Don't allow building phy-core as a module
  phy-core: Don't propagate -ENOSUPP from phy_pm_runtime_get_sync to caller
  phy-core: phy_get: Leave error logging to the caller
  phy,phy-bcm-kona-usb2.c: Add dependency on HAS_IOMEM
  usb: musb: correct use of schedule_delayed_work()
  usb: musb: do not sleep in atomic context
  USB: serial: option: blacklist interface 4 for Cinterion PHS8 and PXS8
  USB: EHCI: add delay during suspend to prevent erroneous wakeups
  usb: gadget: bcm63xx_udc: fix build failure on DMA channel code
  usb: musb: do not sleep in atomic context
  usb: gadget: s3c2410_udc: Fix build error
  usb: musb: core: Fix remote-wakeup resume
  usb: musb: host: Fix SuperSpeed hub enumeration
  usb: musb: fix obex in g_nokia.ko causing kernel panic

Pull TTY revert from Greg KH:
 "Here is a single commit, a revert of a sysfs file change that ended up
  breaking a userspace tool"

* tag 'tty-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "tty: Set correct tty name in 'active' sysfs attribute"

Pull staging tree fix from Greg KH:
 "Here is a single android driver fix for 3.14-rc4 that fixes a reported
  problem in the binder driver"

* tag 'staging-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: binder: Fix death notifications

Pull char/misc fix from Greg KH:
 "Here is a single commit, to fix a reported problem in the mei driver"

* tag 'char-misc-3.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: set client's read_cb to NULL when flow control fails

Add myself as an additional maintainer for the Broadcom mobile
SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge remote-tracking branches 'regulator/fix/da9063', 'regulator/fix/max14577' and 'regulator/fix/s5m8767' into regulator-linus

This reverts commit d8a5dc30.

This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect.  Either way, this needs
to be reverted until it is all figured out.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Ray Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>