- 31 May, 2019 40 commits
-
-
Aditya Pakki authored
[ Upstream commit f37d8e67 ] pch_alloc_dma_buf allocated tx, rx DMA buffers which can fail. Further, these buffers are used without a check. The patch checks for these failures and sends the error upstream. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
James Smart authored
[ Upstream commit c95a3b4b ] During debug, it was seen that the driver is issuing commands specific to SLI3 on SLI4 devices. Although the adapter correctly rejected the command, this should not be done. Revise the code to stop sending these commands on a SLI4 adapter. Signed-off-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Smart <jsmart2021@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 03aa4f19 ] Two saa7146/hexium files contain a construct that causes a warning when built with clang: drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe' [-Werror,-Wframe-larger-than=] static int hexium_probe(struct saa7146_dev *dev) ^ drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach' [-Werror,-Wframe-larger-than=] static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info) ^ This one happens regardless of KASAN, and the problem is that a constructor to initialize a dynamically allocated structure leads to a copy of that structure on the stack, whereas gcc initializes it in place. Link: https://bugs.llvm.org/show_bug.cgi?id=40776Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> [hverkuil-cisco@xs4all.nl: fix checkpatch warnings] Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
James Smart authored
[ Upstream commit d67f935b ] The FDMI manufacturer value being reported on Linux is inconsistent with other OS's. Set the value to "Emulex Corporation" for consistency. Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit ed713a4a ] clang-8 warns about one function here when KASAN is enabled, even without the 'asan-stack' option: drivers/media/usb/go7007/go7007-fw.c:1551:5: warning: stack frame size of 2656 bytes in function I have reported this issue in the llvm bugzilla, but to make it work with the clang-8 release, a small annotation is still needed. Link: https://bugs.llvm.org/show_bug.cgi?id=38809Signed-off-by:
-
James Hutchinson authored
[ Upstream commit 981fbe3d ] Ref: https://bugzilla.kernel.org/show_bug.cgi?id=199323 Users are experiencing problems with the DVBSky S960/S960C USB devices since the following commit: 9d659ae1: ("locking/mutex: Add lock handoff to avoid starvation") The device malfunctions after running for an indeterminable period of time, and the problem can only be cleared by rebooting the machine. It is possible to encourage the problem to surface by blocking the signal to the LNB. Further debugging revealed the cause of the problem. In the following capture: - thread #1325 is running m88ds3103_set_frontend - thread #42 is running ts2020_stat_work a> [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 07 80 [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 08 [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 68 3f [42] usb 1-1: dvb_usb_v2_generic_io: <<< 08 ff [42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11 [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 3d [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff b> [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 07 00 [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07 [42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11 [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 21 [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff [42] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11 [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 [42] usb 1-1: dvb_usb_v2_generic_io: >>> 09 01 01 60 66 [42] usb 1-1: dvb_usb_v2_generic_io: <<< 07 ff [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 68 02 03 11 [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07 [1325] usb 1-1: dvb_usb_v2_generic_io: >>> 08 60 02 10 0b [1325] usb 1-1: dvb_usb_v2_generic_io: <<< 07 Two i2c messages are sent to perform a reset in m88ds3103_set_frontend: a. 0x07, 0x80 b. 0x07, 0x00 However, as shown in the capture, the regmap mutex is being handed over to another thread (ts2020_stat_work) in between these two messages. >From here, the device responds to every i2c message with an 07 message, and will only return to normal operation following a power cycle. Use regmap_multi_reg_write to group the two reset messages, ensuring both are processed before the regmap mutex is unlocked. Signed-off-by:
James Hutchinson <jahutchinson99@googlemail.com> Reviewed-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sameer Pujar authored
[ Upstream commit f6ed6491 ] adma driver is using pm_clk_*() interface for managing clock resources. With this it is observed that clocks remain ON always. This happens on Tegra devices which use BPMP co-processor to manage clock resources, where clocks are enabled during prepare phase. This is necessary because clocks to BPMP are always blocking. When pm_clk_*() interface is used on such Tegra devices, clock prepare count is not balanced till remove call happens for the driver and hence clocks are seen ON always. Thus this patch replaces pm_clk_*() with devm_clk_*() framework. Suggested-by:
Mohan Kumar D <mkumard@nvidia.com> Reviewed-by:
Jonathan Hunter <jonathanh@nvidia.com> Signed-off-by:
Sameer Pujar <spujar@nvidia.com> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 608f729c ] Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA memory in get_fw_boot_info() but attempt to free it anyway: drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized] if (!(val & 0x07)) { ^~~~~~~~~~~~~ drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma); ^~~~~~~ drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true if (!(val & 0x07)) { ^~~~~~~~~~~~~~~~~~~ drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning dma_addr_t buf_dma; ^ = 0 Skip the call to dma_free_coherent() here. Fixes: 2a991c21 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi") Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 8ead7e81 ] If ohci-platform is runtime suspended, we can currently get an "imprecise external abort" on reboot with ohci-platform loaded when PM runtime is implemented for the SoC. Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown. Signed-off-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Paul E. McKenney authored
[ Upstream commit ad092c02 ] If the specified rcuperf.perf_type is not in the rcu_perf_init() function's perf_ops[] array, rcuperf prints some console messages and then invokes rcu_perf_cleanup() to set state so that a future torture test can run. However, rcu_perf_cleanup() also attempts to end the test that didn't actually start, and in doing so relies on the value of cur_ops, a value that is not particularly relevant in this case. This can result in confusing output or even follow-on failures due to attempts to use facilities that have not been properly initialized. This commit therefore sets the value of cur_ops to NULL in this case and inserts a check near the beginning of rcu_perf_cleanup(), thus avoiding relying on an irrelevant cur_ops value. Signed-off-by:
Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by:
-
Paul E. McKenney authored
[ Upstream commit b813afae ] If the specified rcutorture.torture_type is not in the rcu_torture_init() function's torture_ops[] array, rcutorture prints some console messages and then invokes rcu_torture_cleanup() to set state so that a future torture test can run. However, rcu_torture_cleanup() also attempts to end the test that didn't actually start, and in doing so relies on the value of cur_ops, a value that is not particularly relevant in this case. This can result in confusing output or even follow-on failures due to attempts to use facilities that have not been properly initialized. This commit therefore sets the value of cur_ops to NULL in this case and inserts a check near the beginning of rcu_torture_cleanup(), thus avoiding relying on an irrelevant cur_ops value. Reported-by:
kernel test robot <rong.a.chen@intel.com> Signed-off-by:
-
Tony Luck authored
[ Upstream commit f19501aa ] There has been a lurking "TBD" in the machine check poll routine ever since it was first split out from the machine check handler. The potential issue is that the poll routine may have just begun a read from the STATUS register in a machine check bank when the hardware logs an error in that bank and signals a machine check. That race used to be pretty small back when machine checks were broadcast, but the addition of local machine check means that the poll code could continue running and clear the error from the bank before the local machine check handler on another CPU gets around to reading it. Fix the code to be sure to only process errors that need to be processed in the poll code, leaving other logged errors alone for the machine check handler to find and process. [ bp: Massage a bit and flip the "== 0" check to the usual !(..) test. ] Fixes: b79109c3 ("x86, mce: separate correct machine check poller and fatal exception handler") Fixes: ed7290d0 ("x86, mce: implement new status bits") Reported-by:
Ashok Raj <ashok.raj@intel.com> Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: Ashok Raj <ashok.raj@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Cc: Yazen Ghannam <Yazen.Ghannam@amd.com> Link: https://lkml.kernel.org/r/20190312170938.GA23035@agluck-deskSigned-off-by:
-
Kangjie Lu authored
[ Upstream commit 1bbb1c31 ] ipw->attr_memory and ipw->common_memory are assigned with the return value of ioremap. ioremap may fail, but no checks are enforced. The fix inserts the checks to avoid potential NULL pointer dereferences. Signed-off-by:
Kangjie Lu <kjlu@umn.edu> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Pankaj Gupta authored
[ Upstream commit 4b0a2c5f ] For regular serial ports we do not initialize value of vtermno variable. A garbage value is assigned for non console ports. The value can be observed as a random integer with [1]. [1] vim /sys/kernel/debug/virtio-ports/vport*p* This patch initialize the value of vtermno for console serial ports to '1' and regular serial ports are initiaized to '0'. Reported-by: siliu@redhat.com Signed-off-by:
Pankaj Gupta <pagupta@redhat.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 9c2ccc32 ] Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen" can copy up to 255 bytes and we only have room for two bytes. Even if this comes from the firmware and we trust it, the new policy generally is just to fix it as kernel hardenning. I can't test this code so I tried to be very conservative. I considered not allowing "evt_hdr->dlen == 1" because it doesn't initialize the whole variable but in the end I decided to allow it and manually initialized "asic_id" and "asic_ver" to zero. Fixes: e8454ff7 ("[media] drivers:media:radio: wl128x: FM Driver Common sources") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Sowjanya Komatineni authored
[ Upstream commit 01919493 ] Fixes: SPI driver can be built as module so perform SPI controller reset on probe to make sure it is in valid state before initiating transfer. Signed-off-by:
Sowjanya Komatineni <skomatineni@nvidia.com> Signed-off-by:
-
Gustavo A. R. Silva authored
[ Upstream commit 76497732 ] The use of zero-sized array causes undefined behaviour when it is not the last member in a structure. As it happens to be in this case. Also, the current code makes use of a language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as this one is a flexible array member, introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last. Which is beneficial to cultivate a high-quality code. Fixes: e48f129c ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Wen Yang authored
[ Upstream commit c7052471 ] The call to of_parse_phandle returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./sound/soc/fsl/fsl_utils.c:74:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function. Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Wen Yang authored
[ Upstream commit b820d52e ] The call to of_parse_phandle returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./sound/soc/fsl/eukrea-tlv320.c:121:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function. ./sound/soc/fsl/eukrea-tlv320.c:127:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function. Signed-off-by:
-
Nicolas Saenz Julienne authored
[ Upstream commit 58e75155 ] As seen on some USB wireless keyboards manufactured by Primax, the HID parser was using some assumptions that are not always true. In this case it's s the fact that, inside the scope of a main item, an Usage Page will always precede an Usage. The spec is not pretty clear as 6.2.2.7 states "Any usage that follows is interpreted as a Usage ID and concatenated with the Usage Page". While 6.2.2.8 states "When the parser encounters a main item it concatenates the last declared Usage Page with a Usage to form a complete usage value." Being somewhat contradictory it was decided to match Window's implementation, which follows 6.2.2.8. In summary, the patch moves the Usage Page concatenation from the local item parsing function to the main item parsing function. Signed-off-by:
Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by:
Terry Junge <terry.junge@poly.com> Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
Chengguang Xu authored
[ Upstream commit de36e16d ] Current overlap checking cannot correctly handle a case which is baseminor < existing baseminor && baseminor + minorct > existing baseminor + minorct. Signed-off-by:
Chengguang Xu <cgxu519@gmx.com> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 67a0514a ] Objtool spotted that we call native_load_gs_index() with AC set. Re-arrange the code to avoid that. Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 88e47182 ] Occasionally GCC is less agressive with inlining and the following is observed: arch/x86/kernel/signal.o: warning: objtool: restore_sigcontext()+0x3cc: call to force_valid_ss.isra.5() with UACCESS enabled arch/x86/kernel/signal.o: warning: objtool: do_signal()+0x384: call to frame_uc_flags.isra.0() with UACCESS enabled Cure this by moving this code out of the AC=1 region, since it really isn't needed for the user access. Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 92606ec9 ] The call to of_get_next_child returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./arch/arm64/kernel/cpu_ops.c:102:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 69, but without a corresponding object release within this function. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Stanley Chu authored
[ Upstream commit 3b141e8c ] For regulators used by UFS, vcc, vccq and vccq2 will have voltage range initialized by ufshcd_populate_vreg(), however other regulators may have undefined voltage range if dt-bindings have no such definition. In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg struct will be zero values and these values will be configured on regulators in different power modes. Currently this may have no harm if both "min_uV" and "max_uV" always keep "zero values" because regulator_set_voltage() will always bypass such invalid values and return "good" results. However improper values shall be fixed to avoid potential bugs. Simply bypass voltage configuration if voltage range is not defined. Signed-off-by:
Stanley Chu <stanley.chu@mediatek.com> Reviewed-by:
Avri Altman <avri.altman@wdc.com> Acked-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
-
Stanley Chu authored
[ Upstream commit 0487fff7 ] Currently if a regulator has "<name>-fixed-regulator" property in device tree, it will skip current limit initialization. This lead to a zero "max_uA" value in struct ufs_vreg. However, "regulator_set_load" operation shall be required on regulators which have valid current limits, otherwise a zero "max_uA" set by "regulator_set_load" may cause unexpected behavior when this regulator is enabled or set as high power mode. Similarly, in device's icc_level configuration flow, the target icc_level shall be updated if regulator also has valid current limit, otherwise a wrong icc_level will be calculated by zero "max_uA" and thus causes unexpected results after it is written to device. Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit 24d413a3 ] Fix a race which leads to an Oops with NULL pointer dereference. The dereference is in brcmf_config_dongle() when cfg_to_ndev() attempts to get net_device structure of interface with index 0 via if2bss mapping. This shouldn't fail because of check for bus being ready in brcmf_netdev_open(), but it's not synchronised with USB disconnect and there is a race: after the check the bus can be marked down and the mapping for interface 0 may be gone. Solve this by modifying disconnect handling so that the removal of mapping of ifidx to brcmf_if structure happens after netdev removal (which is synchronous with brcmf_netdev_open() thanks to rtln being locked in devinet_ioctl()). This assures brcmf_netdev_open() returns before the mapping is removed during disconnect. Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = bcae2612 [00000008] *pgd=8be73831 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: brcmfmac brcmutil nf_log_ipv4 nf_log_common xt_LOG xt_limit iptable_mangle xt_connmark xt_tcpudp xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 iptable_filter ip_tables x_tables usb_f_mass_storage usb_f_rndis u_ether usb_serial_simple usbserial cdc_acm smsc95xx usbnet ci_hdrc_imx ci_hdrc usbmisc_imx ulpi 8250_exar 8250_pci 8250 8250_base libcomposite configfs udc_core [last unloaded: brcmutil] CPU: 2 PID: 24478 Comm: ifconfig Not tainted 4.19.23-00078-ga62866d-dirty #115 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) PC is at brcmf_cfg80211_up+0x94/0x29c [brcmfmac] LR is at brcmf_cfg80211_up+0x8c/0x29c [brcmfmac] pc : [<7f26a91c>] lr : [<7f26a914>] psr: a0070013 sp : eca99d28 ip : 00000000 fp : ee9c6c00 r10: 00000036 r9 : 00000000 r8 : ece4002c r7 : edb5b800 r6 : 00000000 r5 : 80f08448 r4 : edb5b968 r3 : ffffffff r2 : 00000000 r1 : 00000002 r0 : 00000000 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 7ca0c04a DAC: 00000051 Process ifconfig (pid: 24478, stack limit = 0xd9e85a0e) Stack: (0xeca99d28 to 0xeca9a000) 9d20: 00000000 80f873b0 0000000d 80f08448 eca99d68 50d45f32 9d40: 7f27de94 ece40000 80f08448 80f08448 7f27de94 ece4002c 00000000 00000036 9d60: ee9c6c00 7f27262c 00001002 50d45f32 ece40000 00000000 80f08448 80772008 9d80: 00000001 00001043 00001002 ece40000 00000000 50d45f32 ece40000 00000001 9da0: 80f08448 00001043 00001002 807723d0 00000000 50d45f32 80f08448 eca99e58 9dc0: 80f87113 50d45f32 80f08448 ece40000 ece40138 00001002 80f08448 00000000 9de0: 00000000 80772434 edbd5380 eca99e58 edbd5380 80f08448 ee9c6c0c 80805f70 9e00: 00000000 ede08e00 00008914 ece40000 00000014 ee9c6c0c 600c0013 00001043 9e20: 0208a8c0 ffffffff 00000000 50d45f32 eca98000 80f08448 7ee9fc38 00008914 9e40: 80f68e40 00000051 eca98000 00000036 00000003 80808b9c 6e616c77 00000030 9e60: 00000000 00000000 00001043 0208a8c0 ffffffff 00000000 80f08448 00000000 9e80: 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 00000000 50d45f32 9ea0: eca98000 80f08448 7ee9fc38 50d45f32 00008914 80f08448 7ee9fc38 80f68e40 9ec0: ed531540 8074721c 00000800 00000001 00000000 6e616c77 00000030 00000000 9ee0: 00000000 00001002 0208a8c0 ffffffff 00000000 50d45f32 80f08448 7ee9fc38 9f00: ed531560 ec8fc900 80285a6c 80285138 edb910c0 00000000 ecd91008 ede08e00 9f20: 80f08448 00000000 00000000 816d8b20 600c0013 00000001 ede09320 801763d4 9f40: 00000000 50d45f32 00021000 edb91118 edb910c0 80f08448 01b29000 edb91118 9f60: eca99f7c 50d45f32 00021000 ec8fc900 00000003 ec8fc900 00008914 7ee9fc38 9f80: eca98000 00000036 00000003 80285a6c 00086364 7ee9fe1c 000000c3 00000036 9fa0: 801011c4 80101000 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc 600c0010 00000003 00000000 00000000 [<7f26a91c>] (brcmf_cfg80211_up [brcmfmac]) from [<7f27262c>] (brcmf_netdev_open+0x74/0xe8 [brcmfmac]) [<7f27262c>] (brcmf_netdev_open [brcmfmac]) from [<80772008>] (__dev_open+0xcc/0x150) [<80772008>] (__dev_open) from [<807723d0>] (__dev_change_flags+0x168/0x1b4) [<807723d0>] (__dev_change_flags) from [<80772434>] (dev_change_flags+0x18/0x48) [<80772434>] (dev_change_flags) from [<80805f70>] (devinet_ioctl+0x67c/0x79c) [<80805f70>] (devinet_ioctl) from [<80808b9c>] (inet_ioctl+0x210/0x3d4) [<80808b9c>] (inet_ioctl) from [<8074721c>] (sock_ioctl+0x350/0x524) [<8074721c>] (sock_ioctl) from [<80285138>] (do_vfs_ioctl+0xb0/0x9b0) [<80285138>] (do_vfs_ioctl) from [<80285a6c>] (ksys_ioctl+0x34/0x5c) [<80285a6c>] (ksys_ioctl) from [<80101000>] (ret_fast_syscall+0x0/0x28) Exception stack(0xeca99fa8 to 0xeca99ff0) 9fa0: 00086364 7ee9fe1c 00000003 00008914 7ee9fc38 00086364 9fc0: 00086364 7ee9fe1c 000000c3 00000036 0008630c 7ee9fe1c 7ee9fc38 00000003 9fe0: 000a42b8 7ee9fbd4 00019914 76e09acc Code: e5970328 eb002021 e1a02006 e3a01002 (e5909008) ---[ end trace 5cbac2333f3ac5df ]--- Signed-off-by:
Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit db3b9e2e ] It was observed that rarely during USB disconnect happening shortly after connect (before full initialization completes) usb_hub_wq would wait forever for the dev_init_lock to be unlocked. dev_init_lock would remain locked though because of infinite wait during usb_kill_urb: [ 2730.656472] kworker/0:2 D 0 260 2 0x00000000 [ 2730.660700] Workqueue: events request_firmware_work_func [ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114) [ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac]) [ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac]) [ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac]) [ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac]) [ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac]) [ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88) [ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808) [ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) [ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000 [ 2733.103926] Workqueue: usb_hub_wq hub_event [ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac) [ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4) [ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0) [ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac]) [ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4) [ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc) [ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc) [ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310) [ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc) [ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc) [ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88) [ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808) [ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) It was traced down to a case where usb_kill_urb would be called on an URB structure containing more or less random data, including large number in its use_count. During the debugging it appeared that in brcmf_usb_free_q() the traversal over URBs' lists is not synchronized with operations on those lists in brcmf_usb_rx_complete() leading to handling brcmf_usbdev_info structure (holding lists' head) as lists' element and in result causing above problem. Fix it by walking through all URBs during brcmf_cancel_all_urbs using the arrays of requests instead of linked lists. Signed-off-by:
-
Piotr Figiel authored
[ Upstream commit a9fd0953 ] Leaving dev_init_lock mutex locked in probe causes BUG and a WARNING when kernel is compiled with CONFIG_PROVE_LOCKING. Convert mutex to completion which silences those warnings and improves code readability. Fix below errors when connecting the USB WiFi dongle: brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43143 for chip BCM43143/2 BUG: workqueue leaked lock or atomic: kworker/0:2/0x00000000/434 last function: hub_event 1 lock held by kworker/0:2/434: #0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: usb_hub_wq hub_event [<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14) [<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4) [<809c4324>] (dump_stack) from [<8014195c>] (process_one_work+0x710/0x808) [<8014195c>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) Exception stack(0xed1d9fb0 to 0xed1d9ff8) 9fa0: 00000000 00000000 00000000 00000000 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ====================================================== WARNING: possible circular locking dependency detected 4.19.23-00084-g454a789-dirty #123 Not tainted ------------------------------------------------------ kworker/0:2/434 is trying to acquire lock: e29cf799 ((wq_completion)"events"){+.+.}, at: process_one_work+0x174/0x808 but task is already holding lock: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (&devinfo->dev_init_lock){+.+.}: mutex_lock_nested+0x1c/0x24 brcmf_usb_probe+0x78/0x550 [brcmfmac] usb_probe_interface+0xc0/0x1bc really_probe+0x228/0x2c0 __driver_attach+0xe4/0xe8 bus_for_each_dev+0x68/0xb4 bus_add_driver+0x19c/0x214 driver_register+0x78/0x110 usb_register_driver+0x84/0x148 process_one_work+0x228/0x808 worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) -> #1 (brcmf_driver_work){+.+.}: worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) -> #0 ((wq_completion)"events"){+.+.}: process_one_work+0x1b8/0x808 worker_thread+0x2c/0x564 kthread+0x13c/0x16c ret_from_fork+0x14/0x20 (null) other info that might help us debug this: Chain exists of: (wq_completion)"events" --> brcmf_driver_work --> &devinfo->dev_init_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&devinfo->dev_init_lock); lock(brcmf_driver_work); lock(&devinfo->dev_init_lock); lock((wq_completion)"events"); *** DEADLOCK *** 1 lock held by kworker/0:2/434: #0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac] stack backtrace: CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: events request_firmware_work_func [<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14) [<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4) [<809c4324>] (dump_stack) from [<80172838>] (print_circular_bug+0x210/0x330) [<80172838>] (print_circular_bug) from [<80175940>] (__lock_acquire+0x160c/0x1a30) [<80175940>] (__lock_acquire) from [<8017671c>] (lock_acquire+0xe0/0x268) [<8017671c>] (lock_acquire) from [<80141404>] (process_one_work+0x1b8/0x808) [<80141404>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564) [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c) [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20) Exception stack(0xed1d9fb0 to 0xed1d9ff8) 9fa0: 00000000 00000000 00000000 00000000 9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit d825db34 ] Clang warns about what is clearly a case of passing an uninitalized variable into a static function: drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here [-Werror,-Wuninitialized] lpphy_papd_cal(dev, gains, 0, 1, 30); ^~~~~ drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here struct lpphy_tx_gains gains, oldgains; ^ 1 error generated. However, this function is empty, and its arguments are never evaluated, so gcc in contrast does not warn here. Both compilers behave in a reasonable way as far as I can tell, so we should change the code to avoid the warning everywhere. We could just eliminate the lpphy_papd_cal() function entirely, given that it has had the TODO comment in it for 10 years now and is rather unlikely to ever get done. I'm doing a simpler change here, and just pass the 'oldgains' variable in that has been initialized, based on the guess that this is what was originally meant. Fixes: 2c0d6100 ("b43: LP-PHY: Begin implementing calibration & software RFKILL support") Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by:
-
Kangjie Lu authored
[ Upstream commit 46953f97 ] In case kmemdup fails, the fix sets conn_info->req_ie_len and conn_info->resp_ie_len to zero to avoid buffer overflows. Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
-
YueHaibing authored
[ Upstream commit 003b686a ] 'hostcmd' is alloced by kzalloc, should be freed before leaving from the error handling cases, otherwise it will cause mem leak. Fixes: 3935ccc1 ("mwifiex: add cfg80211 testmode support") Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 76597628 ] In case alloc_workqueue fails, the fix reports the error and returns to avoid NULL pointer dereference. Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 6f9ca1d3 ] When building with -Wsometimes-uninitialized, Clang warns: drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable 'calculated_time' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized] While it isn't wrong, this will never be a problem because iio_push_to_buffers_with_timestamp only uses calculated_time on the same condition that it is assigned (when scan_timestamp is not zero). While iio_push_to_buffers_with_timestamp is marked as inline, Clang does inlining in the optimization stage, which happens after the semantic analysis phase (plus inline is merely a hint to the compiler). Fix this by just zero initializing calculated_time. Link: https://github.com/ClangBuiltLinux/linux/issues/394Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Kangjie Lu authored
[ Upstream commit 536cc27d ] devm_regmap_init_i2c may fail and return NULL. The fix returns the error when it fails. Signed-off-by:
-
Lars-Peter Clausen authored
[ Upstream commit df1d80ae ] For devices from the SigmaDelta family we need to keep CS low when doing a conversion, since the device will use the MISO line as a interrupt to indicate that the conversion is complete. This is why the driver locks the SPI bus and when the SPI bus is locked keeps as long as a conversion is going on. The current implementation gets one small detail wrong though. CS is only de-asserted after the SPI bus is unlocked. This means it is possible for a different SPI device on the same bus to send a message which would be wrongfully be addressed to the SigmaDelta device as well. Make sure that the last SPI transfer that is done while holding the SPI bus lock de-asserts the CS signal. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Alexandru Ardelean <Alexandru.Ardelean@analog.com> Signed-off-by:
-
Kees Cook authored
[ Upstream commit 7c21383f ] The LLVM linker (ld.lld) defaults to removing local relocations, which causes KASLR boot failures. ld.bfd and ld.gold already handle this correctly. This adds the explicit instruction "--discard-none" during the link phase. There is no change in output for ld.bfd and ld.gold, but ld.lld now produces an image with all the needed relocations. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 8d10dc28 ] The call to of_find_node_by_name returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function. ./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function. ./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function. Signed-off-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
-
Wen Yang authored
[ Upstream commit a9acc26b ] The call to of_get_cpu_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function. ./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function. Signed-off-by:
-
Wen Yang authored
[ Upstream commit 23329803 ] The call to of_get_cpu_node returns a node pointer with refcount incremented thus it must be explicitly decremented after the last usage. Detected by coccinelle with the following warnings: ./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function. ./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function. Signed-off-by:
-
