If a device event generates gratuitous ARP messages, only primary
address is used for sending. This patch iterates through the whole
list. Tested with 2 IP addresses configuration on bonding interface.
Signed-off-by: Zoltan Kiss <schaman@sch.bme.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Original commit 2bda8a0c... "Disable router anycast
address for /127 prefixes" says:

|   No need for matching code in addrconf_leave_anycast() as it
|   will silently ignore any attempt to leave an unknown anycast
|   address.

After analysis, because 1) we may add two or more prefixes on the
same interface, or 2)user may have manually joined that anycast,
we may hit chances to have anycast address which as if we had
generated one by /127 prefix and we should not leave from subnet-
router anycast address unconditionally.

CC: Bjørn Mork <bjorn@mork.no>
CC: Brian Haley <brian.haley@hp.com>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable 'tracer' never be used, so remove it.
Added by f701e5b7.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Take Eric's patch one step further.
Use netdev_skb_ip_align to do setup the receive skb.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (lm78) Become the maintainer
  hwmon: (lm78) Make ISA interface depend on CONFIG_ISA
  hwmon: (lm78) Avoid forward declarations
  hwmon: (sht15) Correct a comment mistake
  hwmon: (max1111) Avoid extra memory allocations
  hwmon: (it87) Add chassis intrusion detection support
  hwmon: (via-cputemp) Add VID reporting support
  hwmon-vid: Add support for VIA family 6 model D CPU
  hwmon: New driver sch5636
  hwmon: (sch5627) Factor out some code shared with sch5636 driver

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  fs: Merge split strings
  treewide: fix potentially dangerous trailing ';' in #defined values/expressions
  uwb: Fix misspelling of neighbourhood in comment
  net, netfilter: Remove redundant goto in ebt_ulog_packet
  trivial: don't touch files that are removed in the staging tree
  lib/vsprintf: replace link to Draft by final RFC number
  doc: Kconfig: `to be' -> `be'
  doc: Kconfig: Typo: square -> squared
  doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
  drivers/net: static should be at beginning of declaration
  drivers/media: static should be at beginning of declaration
  drivers/i2c: static should be at beginning of declaration
  XTENSA: static should be at beginning of declaration
  SH: static should be at beginning of declaration
  MIPS: static should be at beginning of declaration
  ARM: static should be at beginning of declaration
  rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
  Update my e-mail address
  PCIe ASPM: forcedly -> forcibly
  gma500: push through device driver tree
  ...

Fix up trivial conflicts:
 - arch/arm/mach-ep93xx/dma-m2p.c (deleted)
 - drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
 - drivers/net/r8169.c (just context changes)

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  fs: take the ACL checks to common code
  bury posix_acl_..._masq() variants
  kill boilerplates around posix_acl_create_masq()
  generic_acl: no need to clone acl just to push it to set_cached_acl()
  kill boilerplate around posix_acl_chmod_masq()
  reiserfs: cache negative ACLs for v1 stat format
  xfs: cache negative ACLs if there is no attribute fork
  9p: do no return 0 from ->check_acl without actually checking
  vfs: move ACL cache lookup into generic code
  CIFS: Fix oops while mounting with prefixpath
  xfs: Fix wrong return value of xfs_file_aio_write
  fix devtmpfs race
  caam: don't pass bogus S_IFCHR to debugfs_create_...()
  get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
  asus-wmi: ->is_visible() can't return negative
  fix jffs2 ACLs on big-endian with 16bit mode_t
  9p: close ACL leaks
  ocfs2_init_acl(): fix a leak
  VFS : mount lock scalability for internal mounts

Declare myself the maintainer of the lm78 driver. I still have a
running system with one of these chips.

Also count myself as a co-author of the driver. With 34 commits over
6 years, it seems fair.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

We should only include support for the ISA interface of the LM78/LM79
if CONFIG_ISA is set. Not only this makes the driver somewhat smaller
on most architectures, but this also avoids poking at random I/O
ports on these architectures.

This is very similiar to what was done for the w83781d driver in
October 2008.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Dean Nelson <dnelson@redhat.com>

Move code around to avoid several forward declarations. Also group
ISA-related functions together, to make future changes easier.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Dean Nelson <dnelson@redhat.com>

sht15_store_heater() is called on _write_ access to heater_enable.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

We can allocate the tx and rx buffers as part of our data structure.
Doing so is faster and spares memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Stanislav Brabec <utx@penguin.cz>

Add chassis intrusion detection support for all supported devices,
using the standard interface.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

At least VIA family 6 model D CPU report the VID settings in a MSR,
so expose the value to user-space. Not sure about model A.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Jeff Rickman <jrickman@myamigos.us>

The VIA family 6 model D CPU (C7-D, Eden 90 nm) can use two different
VID tables, we have to check the value of a MSR to decide which one to
use.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Jeff Rickman <jrickman@myamigos.us>

This patch adds a new driver for SMSC SCH5636 Super I/O chips.
The chips include an embedded microcontroller for hardware monitoring
solutions, allowing motherboard manufacturers to create their own
custom hwmon solution based upon the SCH5636.

Currently the sch5636 driver only supports the Fujitsu Theseus SCH5636
based hwmon solution. The sch5636 driver runs a sanity check on
loading to ensure it is dealing with a Fujitsu Theseus and not with
another custom SCH5636 based hwmon solution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This patch adds a new sch56xx-common.ko which contains code which will also
be used in the new sch5636 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Merge branch 'next/deletion' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc

* 'next/deletion' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
  ARM: mach-loki: delete
  ARM: mach-s3c2400: delete
  ARM: mach-s3c24a0: delete

* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
  ARM: EXYNOS4: Change devname for FIMD clkdev
  ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
  ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
  ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
  ARM: S3C24XX: Use generic s3c_set_platdata for devices
  ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
  ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
  ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
  ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
  ARM: SAMSUNG: Use generic s3c_set_platdata for FB
  ARM: SAMSUNG: Use generic s3c_set_platdata for TS
  ARM: S3C64XX: Add PWM backlight support on SMDK6410
  ARM: S5P64X0: Add PWM backlight support on SMDK6450
  ARM: S5P64X0: Add PWM backlight support on SMDK6440
  ARM: S5PC100: Add PWM backlight support on SMDKC100
  ARM: S5PV210: Add PWM backlight support on SMDKV210
  ARM: EXYNOS4: Add PWM backlight support on SMDKC210
  ARM: EXYNOS4: Add PWM backlight support on SMDKV310
  ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
  clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
  ...

Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c

* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
  ARM: msm: platsmp: determine number of CPU cores at boot time
  ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
  ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
  ARM: orion5x: fixup 5181 MPP mask check
  ARM: mxs-dma: include <linux/dmaengine.h>
  ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
  ARM: i.MX53: UARTn_CTS pin should not change RTS input select
  ARM: i.MX53: UARTn_TXD pin should not change RXD input select
  ARM: mx25: Fix typo on CAN1_RX pad setting
  iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
  ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
  ARM: i.MX53: Fix IOMUX type o's
  ARM i.MX dma: Fix burstsize settings
  mach-mx5: fix the I2C clock parents
  ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
  ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
  ARM: mx53: Fix some interrupts marked as reserved.
  MXC: iomux-v3: correct NO_PAD_CTRL definition
  ...

Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Allow i2c_add_numbered_adapter() to assign a bus id
  i2c-ali1535: Fix style issues

Replace the ->check_acl method with a ->get_acl method that simply reads an
ACL from disk after having a cache miss.  This means we can replace the ACL
checking boilerplate code with a single implementation in namei.c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

made static; no callers left outside of posix_acl.c.  posix_acl_clone() also
has lost all external callers and became static...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

new helper: posix_acl_create(&acl, gfp, mode_p).  Replaces acl with
modified clone, on failure releases acl and replaces with NULL.
Returns 0 or -ve on error.  All callers of posix_acl_create_masq()
switched.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

In-core acls are copy-on-write, so the reference taken by set_cached_acl() will
do just fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

new helper: posix_acl_chmod(&acl, gfp, mode).  Replaces acl with modified
clone or with NULL if that has failed; returns 0 or -ve on error.  All
callers of posix_acl_chmod_masq() switched to that - they'd been doing
exactly the same thing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Always set up a negative ACL cache entry if the inode can't have ACLs.
That behaves much better than doing this check inside ->check_acl.

Also remove the left over MAY_NOT_BLOCK check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Always set up a negative ACL cache entry if the inode doesn't have an
attribute fork.  That behaves much better than doing this check inside
->check_acl.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

If we do not want to use ACLs we at least need to perform normal Unix
permission checks.  From the comment I'm not quite sure that's what
is intended, but if 0p wants to do permission checks entirely on the
server it needs to do so in ->permission, not in ->check_acl.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

This moves logic for checking the cached ACL values from low-level
filesystems into generic code.  The end result is a streamlined ACL
check that doesn't need to load the inode->i_op->check_acl pointer at
all for the common cached case.

The filesystems also don't need to check for a non-blocking RCU walk
case in their acl_check() functions, because that is all handled at a
VFS layer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

commit fec11dd9 caused
a regression when we have already mounted //server/share/a
and want to mount //server/share/a/b.

The problem is that lookup_one_len calls __lookup_hash
with nd pointer as NULL. Then __lookup_hash calls
do_revalidate in the case when dentry exists and we end
up with NULL pointer deference in cifs_d_revalidate:

if (nd->flags & LOOKUP_RCU)
	return -ECHILD;

Fix this by checking nd for NULL.
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The fsync prototype change commit 02c24a82 accidentally overwrote
the ssize_t return value of xfs_file_aio_write with 0 for SYNC type
writes. Fix this by checking if an error occured when calling
xfs_file_fsync and only change the return value in this case.
In addition xfs_file_fsync actually returns a normal negative error, so
fix this, too.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

After we's done complete(&req->done), there's nothing to prevent the
scope containing *req from being gone and *req overwritten by any
kind of junk.  So we must read req->next before that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

* 'for-3.1/drivers' of git://git.kernel.dk/linux-block:
  cciss: do not attempt to read from a write-only register
  xen/blkback: Add module alias for autoloading
  xen/blkback: Don't let in-flight requests defer pending ones.
  bsg: fix address space warning from sparse
  bsg: remove unnecessary conditional expressions
  bsg: fix bsg_poll() to return POLLOUT properly

* 'for-3.1/core' of git://git.kernel.dk/linux-block: (24 commits)
  block: strict rq_affinity
  backing-dev: use synchronize_rcu_expedited instead of synchronize_rcu
  block: fix patch import error in max_discard_sectors check
  block: reorder request_queue to remove 64 bit alignment padding
  CFQ: add think time check for group
  CFQ: add think time check for service tree
  CFQ: move think time check variables to a separate struct
  fixlet: Remove fs_excl from struct task.
  cfq: Remove special treatment for metadata rqs.
  block: document blk_plug list access
  block: avoid building too big plug list
  compat_ioctl: fix make headers_check regression
  block: eliminate potential for infinite loop in blkdev_issue_discard
  compat_ioctl: fix warning caused by qemu
  block: flush MEDIA_CHANGE from drivers on close(2)
  blk-throttle: Make total_nr_queued unsigned
  block: Add __attribute__((format(printf...) and fix fallout
  fs/partitions/check.c: make local symbols static
  block:remove some spare spaces in genhd.c
  block:fix the comment error in blkdev.h
  ...

When CONFIG_PCI is not enabled, CONFIG_EISA=y, and CONFIG_GENERIC_IOMAP=y,
drivers/net/3c59x.c build fails due to a recent small change to
<asm-generic/iomap.h> that surrounds pci_iomap() and pci_iounmap() with
#ifdef CONFIG_PCI/#endif.

Since that patch to iomap.h looks correct, add stubs for pci_iomap() and
pci_iounmap() with CONFIG_PCI is not enabled to fix the build errors.

  drivers/net/3c59x.c:1026: error: implicit declaration of function 'pci_iomap'
  drivers/net/3c59x.c:1038: error: implicit declaration of function 'pci_iounmap'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently, if an i2c bus driver supports both static and dynamic bus
ids, it needs to choose between calling i2c_add_numbered_adapter() and
i2c_add_adapter().  This patch makes i2c_add_numbered_adapter()
redirect to i2c_add_adapter() if the requested bus id is -1.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This is a fix-style patch for i2c-ali1535 (issues reported by
checkpatch.pl.)
Signed-off-by: LABBE Corentin <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Merge branch 'tegra/fixes' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into next/fixes

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] s5pv210: make needlessly global symbols static
  [CPUFREQ] exynos4210: make needlessly global symbols static
  [CPUFREQ] S3C6410: Add some lower frequencies for 800MHz base clock operation
  [CPUFREQ] S5PV210: Add reboot notifier to prevent system hang
  [CPUFREQ] S5PV210: Adjust udelay prior to voltage scaling down
  [CPUFREQ] S5PV210: Lock a mutex while changing the cpu frequency
  [CPUFREQ] S5PV210: Add pm_notifier to prevent system unstable
  [CPUFREQ] S5PV210: Add arm/int voltage control support
  [CPUFREQ] S5PV210: Add additional symantics for "relation" in cpufreq with pm
  [CPUFREQ] S3C64xx: Notify transition complete as soon as frequency changed
  [CPUFREQ] S3C6410: Support 800MHz operation in cpufreq
  [CPUFREQ] s5pv210-cpufreq.c: Add missing clk_put
  [CPUFREQ] Move compile for S3C64XX cpufreq to /drivers/cpufreq
  [CPUFREQ] Remove some vi noise that escaped into the Makefile.
  [CPUFREQ] Move ARM Samsung cpufreq drivers to drivers/cpufreq/
  [CPUFREQ/S3C64xx] Move S3C64xx CPUfreq driver into drivers/cpufreq
  [CPUFREQ] Handle CPUs with different capabilities in acpi-cpufreq