Sparse reports a warning at sctp_transport_walk_stop()

warning: context imbalance in sctp_transport_walk_stop
	- wrong count at exit

The root cause is the missing annotation at sctp_transport_walk_stop()
Add the missing __releases(RCU) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse reports a warning at sctp_transport_walk_start()

warning: context imbalance in sctp_transport_walk_start
	- wrong count at exit

The root cause is the missing annotation at sctp_transport_walk_start()
Add the missing __acquires(RCU) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse reports a warning at sctp_err_finish()
warning: context imbalance in sctp_err_finish() - unexpected unlock

The root cause is a missing annotation at sctp_err_finish()
Add the missing  __releases(&((__sk)->sk_lock.slock)) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6mr_for_each_table() macro uses list_for_each_entry_rcu()
for traversing outside an RCU read side critical section
but under the protection of rtnl_mutex. Hence add the
corresponding lockdep expression to silence the following
false-positive warnings:

[    4.319479] =============================
[    4.319480] WARNING: suspicious RCU usage
[    4.319482] 5.5.4-stable #17 Tainted: G            E
[    4.319483] -----------------------------
[    4.319485] net/ipv6/ip6mr.c:1243 RCU-list traversed in non-reader section!!

[    4.456831] =============================
[    4.456832] WARNING: suspicious RCU usage
[    4.456834] 5.5.4-stable #17 Tainted: G            E
[    4.456835] -----------------------------
[    4.456837] net/ipv6/ip6mr.c:1582 RCU-list traversed in non-reader section!!
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IDT 82P33 Synchronization Management Unit (SMU) family provides
tools to manage timing references, clock sources and
timing paths for IEEE 1588 / Precision Time Protocol (PTP) and
Synchronous Ethernet (SyncE) based clocks. The device supports up
to three independent timing paths that control: PTP clock synthesis;
SyncE clock generation; and general purpose frequency translation.
The device supports physical layer timing with Digital PLLs (DPLLs)
and it supports packet based timing with Digitally Controlled
Oscillators (DCOs). This patch adds support for ptp clock based on
the device.

Changes since v1:
 - As suggested by Richard Cochran:
   1. Replace _mask_bit_count with the existing hweight8
   2. Prefix all functions with idt82p33
   3. Fix white space issues in Kconfig and Makefile
   4. Remove forward declaration
   5. Use adjfine instead of adjfreq for better resolution

 - As suggested by David Miller:
   1. Replace CHAN_INIT macro with a static function
      idt82p33_channel_init
   2. Employ reverse christmas tree ordering for local
      variables
   3. Fix indentation problem by appropriate number of
      TAB then SPACE character
Signed-off-by: Min Li <min.li.xe@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree binding doc for the PTP clock based on IDT 82P33
Synchronization Management Unit (SMU).

Changes since v1:
 - As suggested by Rob Herring:
   1. Drop reg description for i2c
   2. Replace i2c@1 with i2c
   3. Add addtionalProperties: false
Signed-off-by: Min Li <min.li.xe@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

md5sig->head maybe traversed using hlist_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of socket lock.

Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

list_for_each_entry_rcu() has built-in RCU and lock checking.

Pass cond argument to list_for_each_entry_rcu() to silence
false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled
by default.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_ulp_list is traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of tcp_ulp_list_lock.

Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.t
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Introduce ACL traps

This patchset allows to track packets that are dropped in HW by ACL.

Unlike the existing mlxsw traps, ACL traps are "source traps".
That means the action is not controlled by HPKT register but directly
in ACL TRAP action. When devlink user changes action from drop to trap
and vice versa, it would be needed to go over all instances of ACL TRAP
action and do change. That does not scale. Instead, resolve this
by introducing "dummy" group with "thin" policer. The purpose of
this policer is to drop as many packets as possible. The ones
that pass through are going to be dropped in devlink code - patch #6
takes care of that.

First four patches are preparation for introduction of ACL traps in mlxsw
so it possible to easily change from drop to trap for source traps
as well - by changing group to "dummy" and back.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test to check functionality of ACL traps.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the helpers assume pref 1 and handle 101. Make that explicit
and pass the values from callers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include test of forbidding to have drop rule on mixed-bound
shared block.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the trap group used to report ACL drops. Setup the trap IDs for
ingress/egress flow action drop. Register the two packet traps
associated with ACL trap group with devlink during driver
initialization. As these are "source traps", set the disabled
trap group to be the dummy, discarding as many packets in HW
as possible.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For "source traps" it is not possible to change HPKT action to discard.
But there is still need to disallow packets arriving to CPU as much as
possible. Handle this by introduction of a "dummy group". It has a
"thin" policer, which passes as less packets to CPU as possible. The
rest is going to be discarded there. The "dummy group" is to be used
later on by ACL trap (which is a "source trap").
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the mlxsw_listener struct to contain trap group for disabled
traps too. Rename the original "trap_group" item to "en_trap_group" as
it represents enabled state. Let both groups be the same for MLXSW_RXL
however extend MLXSW_RXL_DIS to register separate groups for enable and
disable.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For source traps, the "thin policer" is going to be used in order
to reduce the amount of trapped packets to minimum. However, there
will be still small number of packets coming in that need to be dropped
in the driver. Allow to enable/disable rx_listener related to specific
trap in order to prevent unwanted packets to go up the stack.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new set of traps:
DISCARD_INGRESS_ACL and DISCARD_EGRESS_ACL
Set the trap_action from NOP to TRAP which causes the packets dropped
by the TRAP action to be trapped under new trap IDs, depending on the
ingress/egress binding point.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ACL flex action will have to know if it is in ingress or egress,
so it can use correct trap ID. Pass the ingress indication down to it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Action drop is going to be tracked by two separate traps, one for
ingress and one for egress. Prepare for it and disallow the possibility
to have drop action in blocks which are bound to both ingress and
egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Count the number of ingress and egress block bindings. Use the egress
counter in "is_egress_bound" helper. Add couple of helpers to check
ingress and mixed bound.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add packet traps that can report packets that were dropped during ACL
processing.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename function mlxsw_core_trap_action_set() to
mlxsw_core_trap_state_set() and pass bool enabled instead of action.
Figure out the action according to the enabled state there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The listener fields en_action and dis_action now contain the actions to
be used for TRAP and DROP devlink trap actions. Use them directly
instead of the hard-coded values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a new macro MLXSW_RXL_DIS that allows to register listeners
as disabled. That allows that from now on, the "action" can be
understood always as "enabled action" and "unreg_action" as "disabled
action". Rename them and treat them accordingly.

Use the new macro for defining drops in spectrum_trap.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently it does not really matter if it is set to DISCARD or
SET_FW_DEFAULT because it is set only during unregister of the listener.
The unreg_action is going to be used for disabling the listener too, so
change to SET_FW_DEFAULT and ensure the HW is going to behave correctly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
Clean driver, module and FW versions

Change log:
 v1:
  * Split all FW cleanups patches to separate patches
  * Fixed commit message
  * Deleted odd DRV_RELDATE
  * Added everyone from MAINTAINERS file
 v0: https://lore.kernel.org/netdev/20200220145855.255704-1-leon@kernel.org

This is first patchset to netdev (already sent RDMA [1] and arch/um [2])
in attempt to unify the version management for in-tree kernel code.
The patches follow already accepted ethtool change [3] to set as
a default linux kernel version.

It allows us to remove driver version and present to the users unified
picture of driver version, which is similar to default MODULE_VERSION().

As part of this series, I deleted various creative attempts to mark
absence of FW. There is no need to set "N/A" in ethtool ->fw_version
field and it is enough to do not set it.

1.
The code is compile tested and passes 0-day kbuild.
2.
The proposed changes are based on commit:
  2bb07f4e ("tc-testing: updated tdc tests for basic filter")
3.
WIP branch is [4].

[1] https://lore.kernel.org/linux-rdma/20200220071239.231800-1-leon@kernel.org/
[2] http://lists.infradead.org/pipermail/linux-um/2020-February/002913.html
[3] https://lore.kernel.org/linux-rdma/20200127072028.19123-1-leon@kernel.org/
[4] https://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma.git/log/?h=ethtool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use linux kernel version for ethtool and module versions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop constant driver version in favour of global linux kernel.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to keep module and driver versions in in-tree
kernel code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to set "N/A" if FW is not available.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete module version in favor of global and unique linux kernel.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert AMD drivers to respect universal linux kernel version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upstream drivers are managed inside global repository and released all
together, this ensure that driver version is the same as linux kernel,
so update amazon drivers to properly reflect it.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert to use default version provided by ethtool.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The acenic driver assigns FW version in driver version field,
as part of cleanup driver version, set FW version properly.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need in custom driver version for in-tree code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use standard variant of the driver version.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need in driver version for in-tree kernel code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If FW version is not available, it is enough to leave that field as
empty, there is no need to write N/A.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>