- 20 Dec, 2021 1 commit
-
-
Manish Chopra authored
This new firmware addresses few important issues and enhancements as mentioned below - - Support direct invalidation of FP HSI Ver per function ID, required for invalidating FP HSI Ver prior to each VF start, as there is no VF start - BRB hardware block parity error detection support for the driver - Fix the FCOE underrun flow - Fix PSOD during FCoE BFS over the NIC ports after preboot driver - Maintains backward compatibility This patch incorporates this new firmware 7.13.21.0 in bnx2x driver. Signed-off-by:
Manish Chopra <manishc@marvell.com> Signed-off-by:
Prabhakar Kushwaha <pkushwaha@marvell.com> Signed-off-by:
Alok Prasad <palok@marvell.com> Signed-off-by:
Ariel Elior <aelior@marvell.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 19 Dec, 2021 14 commits
-
-
David S. Miller authored
Simon Horman says: ==================== allow user to offload tc action to net device Baowen Zheng says: Allow use of flow_indr_dev_register/flow_indr_dev_setup_offload to offload tc actions independent of flows. The motivation for this work is to prepare for using TC police action instances to provide hardware offload of OVS metering feature - which calls for policers that may be used by multiple flows and whose lifecycle is independent of any flows that use them. This patch includes basic changes to offload drivers to return EOPNOTSUPP if this feature is used - it is not yet supported by any driver. Tc cli command to offload and quote an action: # tc qdisc del dev $DEV ingress && sleep 1 || true # tc actions delete action police index 200 || true # tc qdisc add dev $DEV ingress # tc qdisc show dev $DEV ingress # tc actions add action police rate 100mbit burst 10000k index 200 skip_sw # tc -s -d actions list action police total acts 1 action order 0: police 0xc8 rate 100Mbit burst 10000Kb mtu 2Kb action reclassify overhead 0b linklayer ethernet ref 1 bind 0 installed 142 sec used 0 sec Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 skip_sw in_hw in_hw_count 1 used_hw_stats delayed # tc filter add dev $DEV protocol ip parent ffff: \ flower skip_sw ip_proto tcp action police index 200 # tc -s -d filter show dev $DEV protocol ip parent ffff: filter pref 49152 flower chain 0 filter pref 49152 flower chain 0 handle 0x1 eth_type ipv4 ip_proto tcp skip_sw in_hw in_hw_count 1 action order 1: police 0xc8 rate 100Mbit burst 10000Kb mtu 2Kb action reclassify overhead 0b linklayer ethernet ref 2 bind 1 installed 300 sec used 0 sec Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 skip_sw in_hw in_hw_count 1 used_hw_stats delayed # tc filter add dev $DEV protocol ipv6 parent ffff: \ flower skip_sw ip_proto tcp action police index 200 # tc -s -d filter show dev $DEV protocol ipv6 parent ffff: filter pref 49151 flower chain 0 filter pref 49151 flower chain 0 handle 0x1 eth_type ipv6 ip_proto tcp skip_sw in_hw in_hw_count 1 action order 1: police 0xc8 rate 100Mbit burst 10000Kb mtu 2Kb action reclassify overhead 0b linklayer ethernet ref 3 bind 2 installed 761 sec used 0 sec Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 skip_sw in_hw in_hw_count 1 used_hw_stats delayed # tc -s -d actions list action police total acts 1 action order 0: police 0xc8 rate 100Mbit burst 10000Kb mtu 2Kb action reclassify overhead 0b linklayer ethernet ref 3 bind 2 installed 917 sec used 0 sec Action statistics: Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) backlog 0b 0p requeues 0 skip_sw in_hw in_hw_count 1 used_hw_stats delayed Changes between v7 and v8: * Rename enum offload_act_command as enum flow_offload_act_command * Add a single patch to rename exts stats update function for readability. * Fix the kernel test robot issue reported by Oliver Sang. Changes between v6 and v7: * Add a single patch to rename offload functions with offload for readability. * Post 166b6a46 ("flow_offload: return EOPNOTSUPP for the unsupported mpls action type") as a bug fix to netdev. * Rename enum flow_act_command as enum flow_offload_act_command * Rename the new added action offload setup ops with offload instead of flow * Rename the new added action offload function with offload instead of flow. * Add more selftest cases for validate filter and actions. Changes between v5 and v6: * Fix issue reported by Dan Carpenter found using Smatch. Changes beteeen v4 and v5: * Made changes of code style according to the public review comments. * Add a fix for unsupported mpls action type in flow action setup stage. * Add ops to tc_action_ops for flow action setup to facilitate adding a standalone action module. * Add notification process when deleting action in reoffload process. Changes between v3 and v4: * Made changes according to the public review comments. * Validate flags inside tcf_action_init() instead of creating new tcf_exts_validate_actions() function. * Exactly match when validating flags of actions and filters. * Add index to flow_action_entry for driver to identify actions. Changes between v2 and v3: * Made changes according to the review comments. * Delete in_hw and not_in_hw flag and user can judge if the action is offloaded to any hardware by in_hw_count. * Split the main patch of the action offload to three single patch to facilitate code review. Changes between v1 and v2: * Add the skip_hw/skip_sw for user to specify if the action should be in hardware or software. * Fix issue of sleeping function called from invalid context. * Change the action offload/delete from batch to one by one. * Add some parameters to the netlink message for user space to look up the offload status of the actions. * Add reoffload process to update action hw_count when driver is inserted or removed. Changes between v1 and RFC: * Fix robot test failure. * Change actions offload process in action add function rather than action init. * Change actions offload delete process after tcf_del_notify to keep undeleted actions. * Add process to update actions stats from hardware. ==================== Signed-off-by: -
Baowen Zheng authored
Add selftest cases in action police with skip_hw. Add selftest case to validate flags of filter and action. These tests depend on corresponding iproute2 command support. Signed-off-by:
Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
-
Baowen Zheng authored
Add process to validate flags of filter and actions when adding a tc filter. We need to prevent adding filter with flags conflicts with its actions. Signed-off-by:
Louis Peens <louis.peens@corigine.com> Signed-off-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
Baowen Zheng authored
Add reoffload process to update hw_count when driver is inserted or removed. We will delete the action if it is with skip_sw flag and not offloaded to any hardware in reoffload process. When reoffloading actions, we still offload the actions that are added independent of filters. Signed-off-by:
-
Baowen Zheng authored
Save full action flags and return user flags when return flags to user space. Save full action flags to distinguish if the action is created independent from classifier. We made this change mainly for further patch to reoffload tc actions. Signed-off-by:
-
Baowen Zheng authored
When collecting stats for actions update them using both hardware and software counters. Stats update process should not run in context of preempt_disable. Signed-off-by:
-
Baowen Zheng authored
Rename exts stats update functions with hw for readability. We make this change also to update stats from hw for an action when it is offloaded to hw as a single action. Signed-off-by:
-
Baowen Zheng authored
We add skip_hw and skip_sw for user to control if offload the action to hardware. We also add in_hw_count for user to indicate if the action is offloaded to any hardware. Signed-off-by:
-
Baowen Zheng authored
Use flow_indr_dev_register/flow_indr_dev_setup_offload to offload tc action. We need to call tc_cleanup_flow_action to clean up tc action entry since in tc_setup_action, some actions may hold dev refcnt, especially the mirror action. Signed-off-by:
-
Baowen Zheng authored
Add a new ops to tc_action_ops for flow action setup. Refactor function tc_setup_flow_action to use this new ops. We make this change to facilitate to add standalone action module. We will also use this ops to offload action independent of filter in following patch. Signed-off-by:
-
Baowen Zheng authored
To improves readability, we rename offload functions with offload instead of flow. The term flow is related to exact matches, so we rename these functions with offload. We make this change to facilitate single action offload functions naming. Signed-off-by:
-
Baowen Zheng authored
Add index to flow_action_entry structure and delete index from police and gate child structure. We make this change to offload tc action for driver to identify a tc action. Signed-off-by:
-
Baowen Zheng authored
A follow-up patch will allow users to offload tc actions independent of classifier in the software datapath. In preparation for this, teach all drivers that support offload of the flow tables to reject such configuration as currently none of them support it. Signed-off-by:
-
Baowen Zheng authored
Fill flags to action structure to allow user control if the action should be offloaded to hardware or not. Signed-off-by:
-
- 18 Dec, 2021 9 commits
-
-
Yajun Deng authored
The xdp_rxq_info_unreg() called by xdp_rxq_info_reg() is meaningless when dev is NULL, so move the if dev statements to the first. Signed-off-by:
Yajun Deng <yajun.deng@linux.dev> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueDavid S. Miller authored
Tony Nguyen says: ==================== 40GbE Intel Wired LAN Driver Updates 2021-12-17 Brett Creeley says: This patch series adds support in the iavf driver for communicating and using VIRTCHNL_VF_OFFLOAD_VLAN_V2. The current VIRTCHNL_VF_OFFLOAD_VLAN is very limited and covers all 802.1Q VLAN offloads and filtering with no granularity. The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 adds more granularity, flexibility, and support for 802.1ad offloads and filtering. This includes the VF negotiating which VLAN offloads/filtering it's allowed, where VLAN tags should be inserted and/or stripped into and from descriptors, and the supported VLAN protocols. ==================== Signed-off-by: -
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Miscellaneous changes for 5.17 These are three unrelated patches that we've been testing in the MPTCP tree. Patch 1 modifies the packet scheduler that picks which TCP subflow is used for each chunk of outgoing data. The updated scheduler improves throughput on multiple-subflow connections. Patch 2 updates a selftest to verify recent TCP_ULP sockopt changes on MPTCP fallback sockets. Patch 3 cleans up some unnecessary comparisons with an 8-bit value. ==================== Link: https://lore.kernel.org/r/20211217233702.299461-1-mathew.j.martineau@linux.intel.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Jean Sacren authored
entry->addr.id is u8 with a range from 0 to 255 and MAX_ADDR_ID is 255. We should drop both false expressions of (entry->addr.id > MAX_ADDR_ID). We should also remove the obsolete parentheses in the first if branch. Use U8_MAX for MAX_ADDR_ID and add a comment to show the link to mptcp_addr_info.id as suggested by Mr. Matthieu Baerts. Reviewed-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
Jean Sacren <sakiwit@gmail.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Florian Westphal authored
The kernel will crash without 'mptcp: clear 'kern' flag from fallback sockets' change. Since this doesn't slow down testing in a noticeable way, run this unconditionally. The explicit test did not catch this, because the check was done for tcp socket returned by 'socket(.. IPPROTO_TCP) rather than a tcp socket returned by accept() on a mptcp listen fd. Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
-
Paolo Abeni authored
The MPTCP packet scheduler has sub-optimal behavior with asymmetric subflows: if the faster subflow-level cwin is closed, the packet scheduler can enqueue "too much" data on a slower subflow. When all the data on the faster subflow is acked, if the mptcp-level cwin is closed, and link utilization becomes suboptimal. The solution is implementing blest-like[1] HoL-blocking estimation, transmitting only on the subflow with the shorter estimated time to flush the queued memory. If such subflows cwin is closed, we wait even if other subflows are available. This is quite simpler than the original blest implementation, as we leverage the pacing rate provided by the TCP socket. To get a more accurate estimation for the subflow linger-time, we maintain a per-subflow weighted average of such info. Additionally drop magic numbers usage in favor of newly defined macros and use more meaningful names for status variable. [1] http://dl.ifip.org/db/conf/networking/networking2016/1570234725.pdf Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/137Reviewed-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Dan Carpenter authored
The debugfs_create_dir() function never returns NULL. It does return error pointers but in normal situations like this there is no need to check for errors. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211217071037.GE26548@kiliSigned-off-by:
-
Dan Carpenter authored
There is already an "int err" declared at the start of the function so re-use that instead of declaring a shadow err variable. Signed-off-by:
-
Gerhard Engleder authored
The following warning is fixed with additional config dependencies: s390-linux-ld: drivers/net/ethernet/engleder/tsnep_main.o: in function `tsnep_probe': tsnep_main.c:(.text+0x1de6): undefined reference to `devm_ioremap_resource' Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Gerhard Engleder <gerhard@engleder-embedded.com> Link: https://lore.kernel.org/r/20211216200154.1520-1-gerhard@engleder-embedded.comSigned-off-by:
-
- 17 Dec, 2021 12 commits
-
-
Brett Creeley authored
For VIRTCHNL_VF_OFFLOAD_VLAN, PF's would limit the number of VLAN filters a VF was allowed to add. However, by the time the opcode failed, the VLAN netdev had already been added. VIRTCHNL_VF_OFFLOAD_VLAN_V2 added the ability for a PF to tell the VF how many VLAN filters it's allowed to add. Make changes to support that functionality. Signed-off-by:
Brett Creeley <brett.creeley@intel.com> Tested-by:
Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Brett Creeley authored
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows the VF to support 802.1Q and 802.1ad VLAN insertion and stripping if successfully negotiated via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS. Multiple changes were needed to support this new functionality. 1. Added new aq_required flags to support any kind of VLAN stripping and insertion offload requests via virtchnl. 2. Added the new method iavf_set_vlan_offload_features() that's used during VF initialization, VF reset, and iavf_set_features() to set the aq_required bits based on the current VLAN offload configuration of the VF's netdev. 3. Added virtchnl handling for VIRTCHNL_OP_ENABLE_STRIPPING_V2, VIRTCHNL_OP_DISABLE_STRIPPING_V2, VIRTCHNL_OP_ENABLE_INSERTION_V2, and VIRTCHNL_OP_ENABLE_INSERTION_V2. Signed-off-by:
-
Brett Creeley authored
The new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability added support that allows the PF to set the location of the Tx and Rx VLAN tag for insertion and stripping offloads. In order to support this functionality a few changes are needed. 1. Add a new method to cache the VLAN tag location based on negotiated capabilities for the Tx and Rx ring flags. This needs to be called in the initialization and reset paths. 2. Refactor the transmit hotpath to account for the new Tx ring flags. When IAVF_TXR_FLAGS_VLAN_LOC_L2TAG2 is set, then the driver needs to insert the VLAN tag in the L2TAG2 field of the transmit descriptor. When the IAVF_TXRX_FLAGS_VLAN_LOC_L2TAG1 is set, then the driver needs to use the l2tag1 field of the data descriptor (same behavior as before). 3. Refactor the iavf_tx_prepare_vlan_flags() function to simplify transmit hardware VLAN offload functionality by only depending on the skb_vlan_tag_present() function. This can be done because the OS won't request transmit offload for a VLAN unless the driver told the OS it's supported and enabled. 4. Refactor the receive hotpath to account for the new Rx ring flags and VLAN ethertypes. This requires checking the Rx ring flags and descriptor status bits to determine the location of the VLAN tag. Also, since only a single ethertype can be supported at a time, check the enabled netdev features before specifying a VLAN ethertype in __vlan_hwaccel_put_tag(). Signed-off-by:
-
Brett Creeley authored
Based on VIRTCHNL_VF_OFFLOAD_VLAN_V2, the VF can now support more VLAN capabilities (i.e. 802.1AD offloads and filtering). In order to communicate these capabilities to the netdev layer, the VF needs to parse its VLAN capabilities based on whether it was able to negotiation VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or neither of these. In order to support this, add the following functionality: iavf_get_netdev_vlan_hw_features() - This is used to determine the VLAN features that the underlying hardware supports and that can be toggled off/on based on the negotiated capabiltiies. For example, if VIRTCHNL_VF_OFFLOAD_VLAN_V2 was negotiated, then any capability marked with VIRTCHNL_VLAN_TOGGLE can be toggled on/off by the VF. If VIRTCHNL_VF_OFFLOAD_VLAN was negotiated, then only VLAN insertion and/or stripping can be toggled on/off. iavf_get_netdev_vlan_features() - This is used to determine the VLAN features that the underlying hardware supports and that should be enabled by default. For example, if VIRTHCNL_VF_OFFLOAD_VLAN_V2 was negotiated, then any supported capability that has its ethertype_init filed set should be enabled by default. If VIRTCHNL_VF_OFFLOAD_VLAN was negotiated, then filtering, stripping, and insertion should be enabled by default. Also, refactor iavf_fix_features() to take into account the new capabilities. To do this, query all the supported features (enabled by default and toggleable) and make sure the requested change is supported. If VIRTCHNL_VF_OFFLOAD_VLAN_V2 is successfully negotiated, there is no need to check VIRTCHNL_VLAN_TOGGLE here because the driver already told the netdev layer which features can be toggled via netdev->hw_features during iavf_process_config(), so only those features will be requested to change. Signed-off-by:
-
Brett Creeley authored
In order to support the new VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability the VF driver needs to rework it's initialization state machine and reset flow. This has to be done because successful negotiation of VIRTCHNL_VF_OFFLOAD_VLAN_V2 requires the VF driver to perform a second capability request via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS before configuring the adapter and its netdev. Add the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit when sending the VIRTHCNL_OP_GET_VF_RESOURECES message. The underlying PF will either support VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2 or neither. Both of these offloads should never be supported together. Based on this, add 2 new states to the initialization state machine: __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS __IAVF_INIT_CONFIG_ADAPTER The __IAVF_INIT_GET_OFFLOAD_VLAN_V2_CAPS state is used to request/store the new VLAN capabilities if and only if VIRTCHNL_VLAN_OFFLOAD_VLAN_V2 was successfully negotiated in the __IAVF_INIT_GET_RESOURCES state. The __IAVF_INIT_CONFIG_ADAPTER state is used to configure the adapter/netdev after the resource requests have finished. The VF will move into this state regardless of whether it successfully negotiated VIRTCHNL_VF_OFFLOAD_VLAN or VIRTCHNL_VF_OFFLOAD_VLAN_V2. Also, add a the new flag IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS and set it during VF reset. If VIRTCHNL_VF_OFFLOAD_VLAN_V2 was successfully negotiated then the VF will request its VLAN capabilities via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS during the reset. This is needed because the PF may change/modify the VF's configuration during VF reset (i.e. modifying the VF's port VLAN configuration). This also, required the VF to call netdev_update_features() since its VLAN features may change during VF reset. Make sure to call this under rtnl_lock(). Signed-off-by:
-
Brett Creeley authored
Currently VIRTCHNL only allows for VLAN filtering and offloads to happen on a single 802.1Q VLAN. Add support to filter and offload on inner, outer, and/or inner + outer VLANs. This is done by introducing the new capability VIRTCHNL_VF_OFFLOAD_VLAN_V2. The flow to negotiate this new capability is shown below. 1. VF - sets the VIRTCHNL_VF_OFFLOAD_VLAN_V2 bit in the virtchnl_vf_resource.vf_caps_flags during the VIRTCHNL_OP_GET_VF_RESOURCES request message. The VF should also set the VIRTCHNL_VF_OFFLOAD_VLAN bit in case the PF driver doesn't support the new capability. 2. PF - sets the VLAN capability bit it supports in the VIRTCHNL_OP_GET_VF_RESOURCES response message. This will either be VIRTCHNL_VF_OFFLOAD_VLAN_V2, VIRTCHNL_VF_OFFLOAD_VLAN, or none. 3. VF - If the VIRTCHNL_VF_OFFLOAD_VLAN_V2 capability was ACK'd by the PF, then the VF needs to request the VLAN capabilities of the PF/Device by issuing a VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS request. If the VIRTCHNL_VF_OFFLOAD_VLAN capability was ACK'd then the VF knows only single 802.1Q VLAN filtering/offloads are supported. If no VLAN capability is ACK'd then the PF/Device doesn't support hardware VLAN filtering/offloads for this VF. 4. PF - Populates the virtchnl_vlan_caps structure based on what it allows/supports for that VF and sends that response via VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS. After VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is successfully negotiated the VF driver needs to interpret the capabilities supported by the underlying PF/Device. The VF will be allowed to filter/offload the inner 802.1Q, outer (various ethertype), inner 802.1Q + outer (various ethertypes), or none based on which fields are set. The VF will also need to interpret where the VLAN tag should be inserted and/or stripped based on the negotiated capabilities. Signed-off-by:
-
Jakub Kicinski authored
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.17 Second set of patches for v5.17, planning to do at least one more. Smaller new features, nothing special this time. Major changes: rtw88 * debugfs file to fix tx rate iwlwifi * support SAR GEO Offset Mapping (SGOM) via BIOS * support firmware API version 68 * add some new device IDs ath11k * support PCI devices with 1 MSI vector * WCN6855 hw2.1 support * 11d scan offload support * full monitor mode, only supported on QCN9074 * scan MAC address randomization support * reserved host DDR addresses from DT for PCI devices support ath9k * switch to rate table based lookup ath * extend South Korea regulatory domain support wcn36xx * beacon filter support * tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits) wcn36xx: Implement beacon filtering wcn36xx: Fix physical location of beacon filter comment wcn36xx: Fix beacon filter structure definitions ath11k: Use reserved host DDR addresses from DT for PCI devices dt: bindings: add new DT entry for ath11k PCI device support wilc1000: Improve WILC TX performance when power_save is off wl1251: specify max. IE length rsi: fix array out of bound wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq" wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx wilc1000: Rename irq handler from "WILC_IRQ" to netdev name wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi" wilc1000: Fix spurious "FW not responding" error wilc1000: Remove misleading USE_SPI_DMA macro wilc1000: Fix missing newline in error message wilc1000: Fix copy-and-paste typo in wilc_set_mac_address rtw89: coex: Update COEX to 5.5.8 rtw89: coex: Cancel PS leaving while C2H comes rtw89: coex: Update BT counters while receiving report rtw89: coex: Define LPS state for BTC using ... ==================== Link: https://lore.kernel.org/r/20211217130952.34887C36AE9@smtp.kernel.orgSigned-off-by:
-
Changcheng Deng authored
Remove unneeded variable used to store return value. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by:
-
Dexuan Cui authored
RX fencing allows the driver to know that any prior change to the RQs has finished, e.g. when the RQs are disabled/enabled or the hashkey/indirection table are changed, RX fencing is required. Remove the previous workaround "ssleep(1)" and add the real support for RX fencing as the PF driver supports the MANA_FENCE_RQ request now (any old PF driver not supporting the request won't be used in production). Signed-off-by:
Dexuan Cui <decui@microsoft.com> Reviewed-by:
Haiyang Zhang <haiyangz@microsoft.com> Link: https://lore.kernel.org/r/20211216001748.8751-1-decui@microsoft.comSigned-off-by:
-
Yang Li authored
Eliminate the following coccicheck warning: ./drivers/net/ethernet/vertexcom/mse102x.c:414:2-3: Unneeded semicolon Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Link: https://lore.kernel.org/r/20211216015433.83383-1-yang.lee@linux.alibaba.comSigned-off-by:
-
Yinjun Zhang authored
The current use of circular buffer to manage stats_context_id is very obscure, and it will cause problem if its element size is not power of two. So change the use more straightforward and scalable, and also change that for mask_id to keep consistency. Signed-off-by:
Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski authored
No conflicts. Signed-off-by:
-
- 16 Dec, 2021 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/auditLinus Torvalds authored
Pull audit fix from Paul Moore: "A single patch to fix a problem where the audit queue could grow unbounded when the audit daemon is forcibly stopped" * tag 'audit-pr-20211216' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: audit: improve robustness of the audit queue handling
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Networking fixes, including fixes from mac80211, wifi, bpf. Relatively large batches of fixes from BPF and the WiFi stack, calm in general networking. Current release - regressions: - dpaa2-eth: fix buffer overrun when reporting ethtool statistics Current release - new code bugs: - bpf: fix incorrect state pruning for <8B spill/fill - iavf: - add missing unlocks in iavf_watchdog_task() - do not override the adapter state in the watchdog task (again) - mlxsw: spectrum_router: consolidate MAC profiles when possible Previous releases - regressions: - mac80211 fixes: - rate control, avoid driver crash for retransmitted frames - regression in SSN handling of addba tx - a memory leak where sta_info is not freed - marking TX-during-stop for TX in in_reconfig, prevent stall - cfg80211: acquire wiphy mutex on regulatory work - wifi drivers: fix build regressions and LED config dependency - virtio_net: fix rx_drops stat for small pkts - dsa: mv88e6xxx: unforce speed & duplex in mac_link_down() Previous releases - always broken: - bpf fixes: - kernel address leakage in atomic fetch - kernel address leakage in atomic cmpxchg's r0 aux reg - signed bounds propagation after mov32 - extable fixup offset - extable address check - mac80211: - fix the size used for building probe request - send ADDBA requests using the tid/queue of the aggregation session - agg-tx: don't schedule_and_wake_txq() under sta->lock, avoid deadlocks - validate extended element ID is present - mptcp: - never allow the PM to close a listener subflow (null-defer) - clear 'kern' flag from fallback sockets, prevent crash - fix deadlock in __mptcp_push_pending() - inet_diag: fix kernel-infoleak for UDP sockets - xsk: do not sleep in poll() when need_wakeup set - smc: avoid very long waits in smc_release() - sch_ets: don't remove idle classes from the round-robin list - netdevsim: - zero-initialize memory for bpf map's value, prevent info leak - don't let user space overwrite read only (max) ethtool parms - ixgbe: set X550 MDIO speed before talking to PHY - stmmac: - fix null-deref in flower deletion w/ VLAN prio Rx steering - dwmac-rk: fix oob read in rk_gmac_setup - ice: time stamping fixes - systemport: add global locking for descriptor life cycle" * tag 'net-5.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (89 commits) bpf, selftests: Fix racing issue in btf_skc_cls_ingress test selftest/bpf: Add a test that reads various addresses. bpf: Fix extable address check. bpf: Fix extable fixup offset. bpf, selftests: Add test case trying to taint map value pointer bpf: Make 32->64 bounds propagation slightly more robust bpf: Fix signed bounds propagation after mov32 sit: do not call ipip6_dev_free() from sit_init_net() net: systemport: Add global locking for descriptor lifecycle net/smc: Prevent smc_release() from long blocking net: Fix double 0x prefix print in SKB dump virtio_net: fix rx_drops stat for small pkts dsa: mv88e6xxx: fix debug print for SPEED_UNFORCED sfc_ef100: potential dereference of null pointer net: stmmac: dwmac-rk: fix oob read in rk_gmac_setup net: usb: lan78xx: add Allied Telesis AT29M2-AF net/packet: rx_owner_map depends on pg_vec netdevsim: Zero-initialize memory for new map's value in function nsim_bpf_map_alloc dpaa2-eth: fix ethtool statistics ixgbe: set X550 MDIO speed before talking to PHY ... -
git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds authored
Pull ARM SoC fixes from Arnd Bergmann: "There are a number of DT fixes, mostly for mistakes found through static checking of the dts files again, as well as a couple of minor changes to address incorrect DT settings. For i.MX, there is yet another series of devitree changes to update RGMII delay settings for ethernet, which is an ongoing problem after some driver changes. For SoC specific device drivers, a number of smaller fixes came up: - i.MX SoC identification was incorrectly registered non-i.MX machines when the driver is built-in - One fix on imx8m-blk-ctrl driver to get i.MX8MM MIPI reset work properly - a few compile fixes for warnings that get in the way of -Werror - a string overflow in the scpi firmware driver - a boot failure with FORTIFY_SOURCE on Rockchips machines - broken error handling in the AMD TEE driver - a revert for a tegra reset driver commit that broke HDA" * tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits) soc/tegra: fuse: Fix bitwise vs. logical OR warning firmware: arm_scpi: Fix string overflow in SCPI genpd driver soc: imx: Register SoC device only on i.MX boards soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name arm64: dts: imx8mq: remove interconnect property from lcdif ARM: socfpga: dts: fix qspi node compatible arm64: dts: apple: add #interrupt-cells property to pinctrl nodes dt-bindings: i2c: apple,i2c: allow multiple compatibles arm64: meson: remove COMMON_CLK arm64: meson: fix dts for JetHub D1 tee: amdtee: fix an IS_ERR() vs NULL bug arm64: dts: apple: change ethernet0 device type to ethernet arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys arm64: dts: rockchip: fix poweroff on helios64 arm64: dts: rockchip: fix audio-supply for Rock Pi 4 arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-edge ARM: rockchip: Use memcpy_toio instead of memcpy on smp bring-up ... -
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf 2021-12-16 We've added 15 non-merge commits during the last 7 day(s) which contain a total of 12 files changed, 434 insertions(+), 30 deletions(-). The main changes are: 1) Fix incorrect verifier state pruning behavior for <8B register spill/fill, from Paul Chaignon. 2) Fix x86-64 JIT's extable handling for fentry/fexit when return pointer is an ERR_PTR(), from Alexei Starovoitov. 3) Fix 3 different possibilities that BPF verifier missed where unprivileged could leak kernel addresses, from Daniel Borkmann. 4) Fix xsk's poll behavior under need_wakeup flag, from Magnus Karlsson. 5) Fix an oob-write in test_verifier due to a missed MAX_NR_MAPS bump, from Kumar Kartikeya Dwivedi. 6) Fix a race in test_btf_skc_cls_ingress selftest, from Martin KaFai Lau. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: bpf, selftests: Fix racing issue in btf_skc_cls_ingress test selftest/bpf: Add a test that reads various addresses. bpf: Fix extable address check. bpf: Fix extable fixup offset. bpf, selftests: Add test case trying to taint map value pointer bpf: Make 32->64 bounds propagation slightly more robust bpf: Fix signed bounds propagation after mov32 bpf, selftests: Update test case for atomic cmpxchg on r0 with pointer bpf: Fix kernel address leakage in atomic cmpxchg's r0 aux reg bpf, selftests: Add test case for atomic fetch on spilled pointer bpf: Fix kernel address leakage in atomic fetch selftests/bpf: Fix OOB write in test_verifier xsk: Do not sleep in poll() when need_wakeup set selftests/bpf: Tests for state pruning with u32 spill/fill bpf: Fix incorrect state pruning for <8B spill/fill ==================== Link: https://lore.kernel.org/r/20211216210005.13815-1-daniel@iogearbox.netSigned-off-by:
-
