- 17 Aug, 2017 2 commits
-
-
Adam Ford authored
Fixes commit 687c2767 ("ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit") This patch corrects an issue where the cd-gpios was improperly setup using IRQ_TYPE_LEVEL_LOW instead of GPIO_ACTIVE_LOW. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Robert Nelson authored
Latest update to the BeagleBoard-X15 platform (revision C). This board contains a silicon update (Rev 2.0), which includes a fix for the 2nd ethernet phy when running at 1000 Mbps speeds. This board can be indentified by the [C.00] after [BBRDX15_] in the at24 eeprom: [BBRDX15_C.001731PX150249] Rev C is now in full production and boards are available for end users. https://beagleboard.org/x15 https://github.com/beagleboard/beagleboard-x15/Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tony Lindgren <tony@atomide.com> CC: Nishanth Menon <nm@ti.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Kishon Vijay Abraham I <kishon@ti.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Drew Fustini <drew@beagleboard.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 16 Aug, 2017 10 commits
-
-
Kishon Vijay Abraham I authored
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra71-evm.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra72-evm-revc.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra72-evm.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74x SoC and use it in the pinctrl properties of MMC devicetree nodes present in am572x-idk.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Include dra72x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra72 SoC and use it in the pinctrl properties of MMC devicetree nodes present in am571x-idk.dts. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sekhar Nori authored
AM572x IDK and AM571x IDK boards have equivalent design of how SD card and eMMC are connected. The two EVMs mainly differ in IOdelay configuration needed (because of difference in SoC used). Move the common properties to am57xx-idk-common.dtsi file which is common for both EVMs. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74 SoC and use it in the pinctrl properties of MMC devicetree nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra7-evm. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sekhar Nori authored
Add pinmux configuration for MMC module including IODELAY values suggested in the data manual for the various supported modes. IOdelay data for both silicon revision 1.1 and 2.0 is added here. The datamanual revisions used are: * AM572x Silicon Revision 2.0: SPRS953B, Revised November 2016 * AM572x Silicon Revision 1.1: SPRS915R, Revised November 2016 Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sekhar Nori authored
Add pinmux configuration for MMC module including IODELAY values suggested in the data manual for the various supported modes. IOdelay data for both silicon revision 1.0 and 2.0 is added here. The datamanual revisions used are: * AM571x Silicon Revision 2.0: SPRS957D, Revised January 2017 * AM571x Silicon Revision 1.0: SPRS919M, Revised November 2017 * DRA71x : SPRS960B, Revised February 2017 Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 14 Aug, 2017 13 commits
-
-
Pavel Machek authored
Add camera support to N900 dts. Also add a note about MMC & debugging. Signed-off-by: Pavel Machek <pavel@ucw.cz> Acked-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Lokesh Vutla authored
dra76-evm is a board based on TI's dra76 processor targeting for infotainment systems. Adding support for this platform. dra76-evm and dra7-evm has a similar layout except with few differences. So create a dra7-evm-common.dtsi with similarities on dra76-evm and dra7-evm. Include this common dtsi in both dra7-evm.dts and dra76-evm.dts Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Lokesh Vutla authored
dra76 family is a high-performance, infotainment application device, based on OMAP architecture on a 28-nm technology. This contains most of the subsystems, peripherals that are available on dra74, dra72 family. This SoC mainly features Subsystems: - 2 x Cortex-A15 with max speed of 1.8GHz - 2 X DSP - 2 X Cortex-M4 IPU - ISS - CAL - DSS - VPE - VIP Connectivity peripherals: - 1 USB3.0 and 3 USB2.0 subsystems - 2 x SATA - 2 x PCI Express Gen2 - 3-port Gigabit ethernet switch - 2 x CAN - MCAN Adding basic dts support for DRA76 family while reusing the data available in dra7.dtsi, dra74x.dtsi. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
Add pcie1 dt node in order for the controller to operate in endpoint mode. However since none of the dra7 based boards have slots configured to operate in endpoint mode, keep EP mode disabled. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
SZ Lin authored
Add support for Moxa UC-8100-ME-T open platform The UC-8100-ME-T computing platform is designed for embedded data acquisition industrial applications The features of UC-8100-ME-T series are: * eMMC * SPI flash * SD slot * 2x LAN * 2 RS-232/422/485 ports, software-selectable * Mini PCIe form factor with USB signal * USB host * EEPROM * TPM * Watchdog * RTC * User gpio-keys * User LEDs * User button Signed-off-by: SZ Lin <sz.lin@moxa.com> Acked-by: Rob Herring <robh@kernel.org> [tony@atomide.com: fix unit adress as suggested by Rob] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Franklin S Cooper Jr authored
Currently the default method of prefetch polled shows the highest possible read and write speed when minimal non NAND background activity is being done. But it is also very CPU intensive to reach these high speeds (CPU load of 99% via mtd performance tests). While DMA prefetch only uses 50% of the CPU to achieve around 23% less in top read and write performance. However, as the non NAND CPU load increases the read and write performance takes a large hit when using polled prefetch. Therefore, prefetch dma mode ends up outperforming prefetch polled in general "system level" test. So switch to using dma prefetch by default since it is likely what most users would prefer. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Franklin S Cooper Jr authored
Currently the default method of prefetch polled shows the highest possible read and write speed when minimal non NAND background activity is being done. But it is also very CPU intensive to reach these high speeds (CPU load of 99% via mtd performance tests). While DMA prefetch only uses 50% of the CPU to achieve around 23% less in top read and write performance. However, as the non NAND CPU load increases the read and write performance takes a large hit when using polled prefetch. Therefore, prefetch dma mode ends up outperforming prefetch polled in general "system level" test. So switch to using dma prefetch by default since it is likely what most users would prefer. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Franklin S Cooper Jr authored
Currently the default method of prefetch polled shows the highest possible read and write speed when minimal non NAND background activity is being done. But it is also very CPU intensive to reach these high speeds (CPU load of 99% via mtd performance tests). While DMA prefetch only uses 50% of the CPU to achieve around 23% less in top read and write performance. However, as the non NAND CPU load increases the read and write performance takes a large hit when using polled prefetch. Therefore, prefetch dma mode ends up outperforming prefetch polled in general "system level" test. So switch to using dma prefetch by default since it is likely what most users would prefer. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sebastian Reichel authored
Add vibrator to Droid4's device tree. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Sebastian Reichel authored
Set default mode for vaudio, which may be left in standby mode if the system is booted via kexec from Android. Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Karthik Tummala authored
All nodes inhert "interrupt-parent" property from root node. Removed the aforementioned property from usbhsohci, usbhsehci, ssi_port1, ssi_port2 nodes to avoid duplication. Signed-off-by: Karthik Tummala <karthik@techveda.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Devices using an external encoder, ESD protection and level shifter such as tpd12s015 or ip4791cz12 have the CEC pull in the encoder chip. And on var-som-om44, there is external pull up resistor R30. So the internal CEC pull-up resistor needs to be disabled as otherwise the external and internal pull are parallel making the pull value much smaller than intended. This leads into the CEC not working as reported by Hans Verkuil <hverkuil@xs4all.nl>. Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Faiz Abbas authored
Add support for onboard gpio buzzer. It works using the gpio-beeper driver. Pinmux entries for GPIO controlling the buzzer are also added. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 10 Aug, 2017 8 commits
-
-
Tony Lindgren authored
Add dra7 iodelay configuration. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-
Enric Balletbo i Serra authored
The interrupt for power button is static data that comes from the datasheet, there is no reason to need to define this value on every board so seams reasonable put this information into the common tps65217 file. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Enric Balletbo i Serra authored
The interrupt specifiers for USB and AC charger input are static data that comes from the datasheet, there is no reason to need to define these values on every board so seem reasonable put this information into the common tps65217 file. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
-
Kishon Vijay Abraham I authored
Replace deprecated "vmmc_aux" with the generic "vqmmc" binding for MMC IO supply. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Linux v4.13-rc1
-
Kishon Vijay Abraham I authored
The GPIO polarity for MMC1 card detect is set to '0' which means active-high. However the polarity should be active-low. Fix it here. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kishon Vijay Abraham I authored
The GPIO polarity for MMC1 card detect is set to '0' which means active-high. However the polarity should be active-low. Fix it here. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 15 Jul, 2017 7 commits
-
-
Linus Torvalds authored
-
git://git.lwn.net/linuxLinus Torvalds authored
Pull documentation format standardization from Jonathan Corbet: "This series converts a number of top-level documents to the RST format without incorporating them into the Sphinx tree. The hope is to bring some uniformity to kernel documentation and, perhaps more importantly, have our existing docs serve as an example of the desired formatting for those that will be added later. Mauro has gone through and fixed up a lot of top-level documentation files to make them conform to the RST format, but without moving or renaming them in any way. This will help when we incorporate the ones we want to keep into the Sphinx doctree, but the real purpose is to bring a bit of uniformity to our documentation and let the top-level docs serve as examples for those writing new ones" * tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits) docs: kprobes.txt: Fix whitespacing tee.txt: standardize document format cgroup-v2.txt: standardize document format dell_rbu.txt: standardize document format zorro.txt: standardize document format xz.txt: standardize document format xillybus.txt: standardize document format vfio.txt: standardize document format vfio-mediated-device.txt: standardize document format unaligned-memory-access.txt: standardize document format this_cpu_ops.txt: standardize document format svga.txt: standardize document format static-keys.txt: standardize document format smsc_ece1099.txt: standardize document format SM501.txt: standardize document format siphash.txt: standardize document format sgi-ioc4.txt: standardize document format SAK.txt: standardize document format rpmsg.txt: standardize document format robust-futexes.txt: standardize document format ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/randomLinus Torvalds authored
Pull random updates from Ted Ts'o: "Add wait_for_random_bytes() and get_random_*_wait() functions so that callers can more safely get random bytes if they can block until the CRNG is initialized. Also print a warning if get_random_*() is called before the CRNG is initialized. By default, only one single-line warning will be printed per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a warning will be printed for each function which tries to get random bytes before the CRNG is initialized. This can get spammy for certain architecture types, so it is not enabled by default" * tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: random: reorder READ_ONCE() in get_random_uXX random: suppress spammy warnings about unseeded randomness random: warn when kernel uses unseeded randomness net/route: use get_random_int for random counter net/neighbor: use get_random_u32 for 32-bit hash random rhashtable: use get_random_u32 for hash_rnd ceph: ensure RNG is seeded before using iscsi: ensure RNG is seeded before use cifs: use get_random_u32 for 32-bit lock random random: add get_random_{bytes,u32,u64,int,long,once}_wait family random: add wait_for_random_bytes() API
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull ->s_options removal from Al Viro: "Preparations for fsmount/fsopen stuff (coming next cycle). Everything gets moved to explicit ->show_options(), killing ->s_options off + some cosmetic bits around fs/namespace.c and friends. Basically, the stuff needed to work with fsmount series with minimum of conflicts with other work. It's not strictly required for this merge window, but it would reduce the PITA during the coming cycle, so it would be nice to have those bits and pieces out of the way" * 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: isofs: Fix isofs_show_options() VFS: Kill off s_options and helpers orangefs: Implement show_options 9p: Implement show_options isofs: Implement show_options afs: Implement show_options affs: Implement show_options befs: Implement show_options spufs: Implement show_options bpf: Implement show_options ramfs: Implement show_options pstore: Implement show_options omfs: Implement show_options hugetlbfs: Implement show_options VFS: Don't use save/replace_mount_options if not using generic_show_options VFS: Provide empty name qstr VFS: Make get_filesystem() return the affected filesystem VFS: Clean up whitespace in fs/namespace.c and fs/super.c Provide a function to create a NUL-terminated string from unterminated data
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull more __copy_.._user elimination from Al Viro. * 'work.__copy_to_user' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: drm_dp_aux_dev: switch to read_iter/write_iter
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull uacess-unaligned removal from Al Viro: "That stuff had just one user, and an exotic one, at that - binfmt_flat on arm and m68k" * 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: kill {__,}{get,put}_user_unaligned() binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull network field-by-field copy-in updates from Al Viro: "This part of the misc compat queue was held back for review from networking folks and since davem has jus ACKed those..." * 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: get_compat_bpf_fprog(): don't copyin field-by-field get_compat_msghdr(): get rid of field-by-field copyin copy_msghdr_from_user(): get rid of field-by-field copyin
-