- 16 May, 2010 7 commits
-
-
Andrew Vasquez authored
Migrate to a consistent set of debug entries during status-IOCB handling: * group CS_TIMEOUT handling with CS_PORT_UNAVAILABLE and the like (more regrouping of common behaviour). * drop CS_DATA_OVERRUN handling as it now falls into the 'default' case (still returns DID_ERROR). * consolidate CS_RESET and CS_ABORTED handling, as we the only functional difference was a printk() (still returns DID_RESET). * dropped all the earlier inconsistent [qla_]printk()s sprinkled throught the needlessly large case-statement. Failure case I/Os are now logged with a 'standard' format: <command failure details> <command generic details> so, for example a dropped-frame is logged as: qla2xxx 0000:13:00.0: scsi(16:0:0) Dropped frame(s) detected (4000 of 4000 bytes). qla2xxx 0000:13:00.0: scsi(16:0:0) FCP command status: 0x15-0x18 (70018) \ oxid=78 ser=76 cdb=280000 len=4000 rsp_info=0 resid=0 fw_resid=4000 which should now convey all relevant information. Signed-off-by:Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
James Bottomley <James.Bottomley@suse.de>
-
Andrew Vasquez authored
Signed-off-by:
-
Andrew Vasquez authored
Prepare CTX infrastructure for additional asynchronous executions, add generic done() operator, pull CMD definitions. Signed-off-by:
Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by:
-
Harish Zunjarrao authored
The driver should not be unloaded if any application is using it. To disallow driver unload, driver use count must be incremented. Application uses this char device as handle and increases driver use count to avoid possible driver unload. Signed-off-by:
-
Lalit Chandivade authored
Currently error status is cleared only after the uncorrectable fatal errors in the qla2xxx_pci_slot_reset. This fix is added to clear the error status in qla2xxx_pci_resume. This way for both fatal and non-fatal errors the error status gets cleared properly. Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=572258Signed-off-by:
-
Andrew Vasquez authored
With qla2xxx using mid-layer async-scsi-scanning, the link state for disconnected port is displayed wrong. Additional check for cable presence is considered to display proper link state. Signed-off-by:
-
Andrew Vasquez authored
Signed-off-by:
-
- 02 May, 2010 30 commits
-
-
Geert Uytterhoeven authored
Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
Signed-off-by:
-
Geert Uytterhoeven authored
wd33c93_release() has been empty since ages, and sgiwd93.c no longer calls it since its conversion to a proper platform driver 2 years ago. Also remove the callers in the m68k wd33c93 shims. Signed-off-by:
-
Christof Schmitt authored
With debug kernels, the memory allocated with kmem_cache_alloc might be initialized with the poison values 6b and a5. Use kmem_cache_zalloc instead of kmem_cache_alloc to get zeroed memory and not send invalid requests. Signed-off-by:
Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by:
-
Christof Schmitt authored
The FCP channel provides the number of status read buffers to issue. Use the provided number instead of the hardcoded number in zfcp. Reviewed-by:
Swen Schillig <swen@vnet.ibm.com> Signed-off-by:
-
Christof Schmitt authored
Waiting for a free sbal is a operation on the qdio queue. Move the code implementing the wait to zfcp_qdio.c and rename the functions accordingly. Reviewed-by:
-
Christof Schmitt authored
Move the code accessing the qdio sbales and zfcp_qdio_req struct to the zfcp_qdio files and provide helper functions for accessing the qdio related parts. Reviewed-by:
-
Christof Schmitt authored
Instead of dealing with large segments in the scatter-gather lists in zfcp_qdio.c, report the limits to the upper layers. With these limits in place, the code for mapping large data blocks to multiple sbales can be removed. Reviewed-by:
-
Ravi Anand authored
Signed-off-by:
Ravi Anand <ravi.anand@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
Vikas Chaudhary <vikas.chaudhary@qlogic.com> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Vikas Chaudhary authored
* Handles SCSI command aborts. * Serialization srb between error handler and command completion path. Signed-off-by:
-
Vikas Chaudhary authored
used cmd->host_scribble to store iocb command handle. Signed-off-by:
-
Vikas Chaudhary authored
Per RFC 3720, Login Response Status Code 0x02 should not be retried. Condensed connection error checking code to a single routine, and added check for status class 0x02. Signed-off-by:
Karen Higgins <karen.higgins@qlogic.com> Signed-off-by:
-
Vikas Chaudhary authored
Updated firmware ready timeout algorithm to prevent long delays and use jiffies to time out instead of counter. Also use msleep_interruptible instead of msleep. Signed-off-by:
-
Vikas Chaudhary authored
Signed-off-by:
-
Vikas Chaudhary authored
Link Down -> Mark all devices missing Previously, the driver took no action on a Link Down, and waited for the I/O on a dead connection to timeout in the firmware before marking the DDB missing. Link Up -> Mark all devices online F/W will do auto login to all the devices only once. After that its the responsibility of the driver to relogin to devices whenever there is : * Any sort of connection failure or * KATO expires indicating target has logged out or * I/O times out etc. Signed-off-by: -
Vikas Chaudhary authored
Signed-off-by:
-
Roland Dreier authored
If cxgb3i_pdu_init() fails, then it appears that cxgb3i_iscsi_init() will not be cleaned up, leading to the iscsi transport being left registered. Fix this by adding a call to cxgb3i_iscsi_cleanup() on the error path. Signed-off-by:
Roland Dreier <rolandd@cisco.com> Reviewed-by:
-
Tom Rini authored
The scsi/scsi.h header is normally provided by the libc (and was not exported by the kernel since 2.6.24) and has been until it was re-exported with 2.6.31. The kernel version is not userspace clean and does not appear to provide anything useable in userland over the (e)glibc version. Signed-off-by:
Tom Rini <tom_rini@mentor.com> Signed-off-by:
-
Dan Carpenter authored
In the original code we dereferenced "pm8001_dev" before checking if it was null. This patch moves the dereference inside the condition. This was found by a static checker (smatch). I looked, but I couldn't tell if "pm8001_dev" dev was ever actually null. The approach in this patch seemed like the safest response. Signed-off-by:
Dan Carpenter <error27@gmail.com> Acked-by:
Jack Wang <jack_wang@usish.com> Signed-off-by:
-
Brian King authored
If a command times out resulting in EH getting invoked, we wait for the aborted commands to come back after sending the abort. Shorten the amount of time we wait for these responses, to ensure we don't get stuck in EH for several minutes. Signed-off-by:
Brian King <brking@linux.vnet.ibm.com> Signed-off-by:
-
Brian King authored
Commands which are completed by the VIOS are placed on a CRQ in kernel memory for the ibmvfc driver to process. Each CRQ entry is 16 bytes. The ibmvfc driver reads the first 8 bytes to check if the entry is valid, then reads the next 8 bytes to get the handle, which is a pointer the completed command. This fixes an issue seen on Power 7 where the processor reordered the loads from memory, resulting in processing command completion with a stale handle. This could result in command timeouts, and also early completion of commands. Signed-off-by:
-
Mike Miller authored
This patch removes unnecessary #define's from hpsa. The SCSI midlayer handles all this for us. Signed-off-by:
Mike Miller <mike.miller@hp.com> Signed-off-by:
-
- 01 May, 2010 3 commits
-
-
Tomohiro Kusumi authored
This patch fixes sdev_rw_attr() macro for scsi device sysfs entries. It seems there is no such function snscanf in the current linux kernel, so it fails to compile scsi driver when someone try to add a new rw entry. This has been unfixed for a long time probably because current scsi device has no rw entries. # grep snscanf . -rn ./drivers/scsi/scsi_sysfs.c:489: snscanf (buf, 20, format_string, &sdev->field); \ Signed-off-by:
Tomohiro Kusumi <kusumi.tomohiro@jp.fujitsu.com> Signed-off-by:
-
Jing Huang authored
Fix the compilation warning in powerpc. The same change also fixes endian issue we found in powerpc test. This patch has been tested in x86 and powerpc platform. it is created using scsi-misc-2.6. Signed-off-by:
Jing Huang <huangj@brocade.com> Signed-off-by:
-
Giridhar Malavali authored
Enhanced the driver to support new FCoE host bus adapter. Signed-off-by:
-
