- 02 Jun, 2015 10 commits
-
-
Doug Ledford authored
-
Ira Weiny authored
In order to support constant callers of agent_send_response we add const specifiers to the its pointer arguments. Adjust the call tree accordingly. Signed-off-by:
Ira Weiny <ira.weiny@intel.com> Reviewed-by:
Hal Rosenstock <hal@mellanox.com> Reviewed-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Doug Ledford <dledford@redhat.com>
-
Ira Weiny authored
The process_mad device function declares some parameters as "in". Make those parameters const and adjust the call tree under process_mad in the various drivers accordingly. Signed-off-by:
-
Ira Weiny authored
The ib_device passed to the new RDMA helpers is constant. Declare the ib_device as const in the following functions. rdma_protocol_ib rdma_protocol_roce rdma_protocol_iwarp rdma_ib_or_roce rdma_cap_ib_mad rdma_cap_ib_smi rdma_cap_ib_cm rdma_cap_iw_cm rdma_cap_ib_sa rdma_cap_ib_mcast rdma_cap_af_ib rdma_cap_eth_ah Signed-off-by:
-
Roland Dreier authored
The unwinding clean up code are err_create_flow starts at the current index i. That means we shouldn't increment i until we're really sure we won't have to destroy the current flow; otherwise we might increment the index, fail inside an is_bonded block, and end up accessing off the end of the reg_id[] array. This was detected by Coverity (CID 1271229). Signed-off-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Roland Dreier authored
If ocrdma_get_pd_num() fails, then we need to free the pd struct we allocated. This was detected by Coverity (CID 1271245). Signed-off-by:
Devesh Sharma <devesh.sharma@avagotech.com> Signed-off-by:
-
Wengang Wang authored
The BUG_ON at line 452/453 is triggered in function rds_send_xmit. 441 while (ret) { 442 tmp = min_t(int, ret, sg->length - 443 conn->c_xmit_data_off); 444 conn->c_xmit_data_off += tmp; 445 ret -= tmp; 446 if (conn->c_xmit_data_off == sg->length) { 447 conn->c_xmit_data_off = 0; 448 sg++; 449 conn->c_xmit_sg++; 450 if (ret != 0 && conn->c_xmit_sg == rm->data.op_nents) 451 printk(KERN_ERR "conn %p rm %p sg %p ret %d\n", conn, rm, sg, ret); 452 BUG_ON(ret != 0 && 453 conn->c_xmit_sg == rm->data.op_nents); 454 } 455 } it is complaining the total sent length is bigger that we want to send. rds_ib_xmit() is wrong for the second entry for the same rds_message returning wrong value. the sg and off passed by rds_send_xmit to rds_ib_xmit is based on scatterlist.offset/length, but the rds_ib_xmit action is based on scatterlist.dma_address/dma_length. in case dma_length is larger than length there is problem. for the 2nd and later entries of rds_ib_xmit for same rds_message, at least one of the following two is wrong: 1) the scatterlist to start with, the choosen one can far beyond the correct one. 2) the offset to start with within the scatterlist. fix: add op_dmasg and op_dmaoff to rm_data_op structure indicating the scatterlist and offset within the it to start with for rds_ib_xmit respectively. op_dmasg and op_dmaoff are initialized to zero when doing dma mapping for the first see of the message and are changed when filling send slots. the same applies to rds_iw_xmit too. Signed-off-by:Wengang Wang <wen.gang.wang@oracle.com> Signed-off-by:
-
Bart Van Assche authored
Avoid that sparse complains about ipoib_neigh_hash_init(). This patch does not change any functionality. See also patch "IPoIB: Fix memory leak in the neigh table deletion flow" (commit ID 66172c09). Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Shlomo Pongratz <shlomop@mellanox.com> Signed-off-by:
-
Faisal Latif authored
RDMA/nes: Enable the use of the tos field in the nes driver Signed-off-by:
Faisal Latif <Faisal.Latif@intel.com> Signed-off-by:
Tatyana Nikolova <Tatyana.E.Nikolova@intel.com> Signed-off-by:
-
Steve Wise authored
rdma-cma/iw_cm: Export tos field to iwarp providers Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
-
- 20 May, 2015 10 commits
-
-
Doug Ledford authored
-
Ira Weiny authored
After discussion upstream, it was agreed to transition the usage of iboe in the kernel to roce. This keeps our terminology consistent with what was finalized in the IBTA Annex 16 and IBTA Annex 17 publications. Signed-off-by:
-
Ira Weiny authored
Remove query_protocol callback Use the new Core Capability bits for: rdma_protocol_* rdma_cap_ib_mad rdma_cap_ib_smi rdma_cap_ib_cm rdma_cap_iw_cm rdma_cap_ib_sa rdma_cap_ib_mcast rdma_cap_af_ib rdma_cap_eth_ah Signed-off-by:
-
Ira Weiny authored
As of commit 5eb620c8 "IB/core: Add helpers for uncached GID and P_Key searches"; pkey_tbl_len and gid_tbl_len are immutable data which are stored in the ib_device. The per port core capability flags to be added later are also immutable data to be stored in the ib_device object. In preparation for this create a structure for per port immutable data and place the pkey and gid table lengths within this structure. "get_port_immutable" is added as a mandatory device function to allow the drivers to fill in this data. Signed-off-by:
-
Ira Weiny authored
The addition of the rdma_cap_ib_mad is technically broken in ib_umad_remove_one because the loop "i" value is not a port value. This bug resulted in the ib_umad failing to properly remove its resources when the core capability functions were converted to bit fields. NOTE: e17371d73908 did not result in broken behavior on its own. It was only an issue when the implementation of rdma_cap_ib_mad was changed. Pass the port value to rdma_cap_ib_mad. Fixes: e17371d73908 ("IB/Verbs: Use management helper rdma_cap_ib_mad()") Signed-off-by: -
Ira Weiny authored
Use the new common rdma_[start|end]_port functions instead of using local variables and figuring it out on the fly. Signed-off-by:
-
Ira Weiny authored
The following functions only need read access to the data passed to them. ib_mad_kernel_rmpp_agent is_rmpp_data_mad rcv_has_same_gid ib_find_send_mad Clarify with const specifiers Signed-off-by:
-
Ira Weiny authored
rcv_has_same_class only needs access to the MAD header specify WR and Receive WC as const Reviewed-By:
Sean Hefty <sean.hefty@intel.com> Signed-off-by:
-
Ira Weiny authored
ib_response_mad only needs read access to the MAD header, not write access to the entire mad struct, so replace struct ib_mad with const struct ib_mad_hdr Reviewed-By:
-
Ira Weiny authored
validate_mad only needs read access to the MAD header, not write access to the entire mad struct, so replace struct ib_mad with const struct ib_mad_hdr Reviewed-By:
-
- 18 May, 2015 20 commits
-
-
Sagi Grimberg authored
Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
-
Sagi Grimberg authored
Reviewed-by:
Chuck Lever <chuck.lever@oracle.com> Signed-off-by:
Anna Schumaker <anna.schumaker@netapp.com> Signed-off-by:
-
Sagi Grimberg authored
Signed-off-by:
-
Sagi Grimberg authored
Signed-off-by:
-
Sagi Grimberg authored
Reviewed-by:
-
Sagi Grimberg authored
Some of us keep revisiting the code to decode enumerations that appear in out logs. Let's borrow the nice logging helpers that exists in xprtrdma and rds for CMA events, IB events and WC statuses. Reviewd-by:
-
Bart Van Assche authored
The SCSI standard defines 64-bit values for LUNs. Large arrays employing large or hierarchical LUN numbers become more and more common. So update the SRP initiator to use 64-bit LUN numbers. See also Hannes Reinecke, commit 9cb78c16 ("scsi: use 64-bit LUNs"), June 2014. The largest LUN number that has been tested is 0xd2003fff00000000. Checked the following structure sizes with gdb: * sizeof(struct srp_cmd) = 48 * sizeof(struct srp_tsk_mgmt) = 48 * sizeof(struct srp_aer_req) = 36 The ibmvscsi changes have been compile tested only (on a PPC system). Signed-off-by:
Hannes Reinecke <hare@suse.de> Reviewed-by:
Yann Droneaud <ydroneaud@opteya.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Cc: Brian King <brking@linux.vnet.ibm.com> Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com> Cc: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by:
-
Bart Van Assche authored
Remove the !ch->target tests from the reconnect code. These tests are not needed: upon entry of srp_rport_reconnect() it is guaranteed that all ch->target pointers are non-NULL. None of the functions srp_new_cm_id(), srp_finish_req(), srp_create_ch_ib() nor srp_connect_ch() modifies this pointer. srp_free_ch_ib() is never called concurrently with srp_rport_reconnect(). Signed-off-by:
-
Bart Van Assche authored
The function srp_free_req_data() does not use ch->target. Hence remove the ch->target != NULL check. Signed-off-by:
-
Bart Van Assche authored
Move the module version and release date into separate fields. This makes the modinfo output easier to read. Signed-off-by:
-
Bart Van Assche authored
A long time ago the data type int64_t was declared as long long on x86 systems and as long on PPC systems. Today that data type is declared as long long on all Linux architectures. This means that the casts from uint64_t into unsigned long long are superfluous. Remove these superfluous casts. Signed-off-by:
-
Bart Van Assche authored
Unlike FC, there is no risk that SCSI devices will be offlined by the SCSI error handler if the SCSI error handler is started while a reconnect attempt is ongoing. Hence report timeout errors as soon as possible if a higher software layer (e.g. multipathd) needs to be informed about a timeout. It is assumed that if both fast_io_fail_tmo < 0 and rport->dev_loss_tmo < 0 that this means that there is no need to report timeouts quickly. Signed-off-by:
-
Bart Van Assche authored
Although it is possible to let SRP I/O continue if a reconnect results in a reduction of the number of channels, the current code does not handle this scenario correctly. Instead of making the reconnect code more complex, consider this as a reconnection failure. Signed-off-by:
-
Bart Van Assche authored
Reception of a DREQ message only causes the state of a single channel to change. Hence move the 'connected' member variable from the target to the channel data structure. This patch avoids that following false positive warning can be reported by srp_destroy_qp(): WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:617 srp_destroy_qp+0xa6/0x120 [ib_srp]() Call Trace: [<ffffffff8106e10f>] warn_slowpath_common+0x7f/0xc0 [<ffffffff8106e16a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa0440226>] srp_destroy_qp+0xa6/0x120 [ib_srp] [<ffffffffa0440322>] srp_free_ch_ib+0x82/0x1e0 [ib_srp] [<ffffffffa044408b>] srp_create_target+0x7ab/0x998 [ib_srp] [<ffffffff81346f60>] dev_attr_store+0x20/0x30 [<ffffffff811dd90f>] sysfs_write_file+0xef/0x170 [<ffffffff8116d248>] vfs_write+0xc8/0x190 [<ffffffff8116d411>] sys_write+0x51/0x90 Signed-off-by:
-
Bart Van Assche authored
Avoid that receiving a DREQ while RDMA channels are being established causes target->qp_in_error to be reset. Signed-off-by:
-
Bart Van Assche authored
Fix a scsi_get_host() / scsi_host_put() imbalance in the error path of srp_create_target(). See also patch "IB/srp: Avoid that I/O hangs due to a cable pull during LUN scanning" (commit ID 34aa654e). Signed-off-by:
-
Bart Van Assche authored
Avoid that srp_terminate_io() can get invoked while srp_queuecommand() is in progress. This patch avoids that an I/O timeout can trigger the following kernel warning: WARNING: at drivers/infiniband/ulp/srp/ib_srp.c:1447 srp_terminate_io+0xef/0x100 [ib_srp]() Call Trace: [<ffffffff814c65a2>] dump_stack+0x4e/0x68 [<ffffffff81051f71>] warn_slowpath_common+0x81/0xa0 [<ffffffff8105204a>] warn_slowpath_null+0x1a/0x20 [<ffffffffa075f51f>] srp_terminate_io+0xef/0x100 [ib_srp] [<ffffffffa07495da>] __rport_fail_io_fast+0xba/0xc0 [scsi_transport_srp] [<ffffffffa0749a90>] rport_fast_io_fail_timedout+0xe0/0xf0 [scsi_transport_srp] [<ffffffff8106e09b>] process_one_work+0x1db/0x780 [<ffffffff8106e75b>] worker_thread+0x11b/0x450 [<ffffffff81073c64>] kthread+0xe4/0x100 [<ffffffff814cf26c>] ret_from_fork+0x7c/0xb0 See also patch "scsi_transport_srp: Add transport layer error handling" (commit ID 29c17324). Signed-off-by:
-
Bart Van Assche authored
Introduce the helper function srp_wait_for_queuecommand(). Move the definition of scsi_request_fn_active(). Add a comment above srp_wait_for_queuecommand() that support for scsi-mq needs to be added. This patch does not change any functionality. A second call to srp_wait_for_queuecommand() will be introduced in the next patch. Signed-off-by:
-
Ira Weiny authored
Return values of 0 do not make sense for functions which return enum smi_action Reviewed-By:
-
Ira Weiny authored
is_rmpp_data_mad is more descriptive for this function. Reviewed-By:
-
