Commit 4e087133 ("ASoC: hdmi-codec: fix channel info for
compressed formats") accidentally changed hcp->chmap_idx from
ca_id, the CEA channel allocation ID, to idx, the index to
the table of channel mappings ordered by preference.

This resulted in wrong channel maps being reported to userspace,
eg for 5.1 "FL,FR,LFE,FC" was reported instead of the expected
"FL,FR,LFE,FC,RL,RR":

~ # speaker-test -c 6 -t sine
...
 0 - Front Left
 3 - Front Center
 1 - Front Right
 2 - LFE
 4 - Unknown
 5 - Unknown

~ # amixer cget iface=PCM,name='Playback Channel Map' | grep ': values'
  : values=3,4,8,7,0,0,0,0

Switch this back to ca_id in case of PCM audio so the correct channel
map is reported again and set it to HDMI_CODEC_CHMAP_IDX_UNKNOWN in
case of non-PCM audio so the PCM channel map control returns "Unknown"
channels (value 0).

Fixes: 4e087133 ("ASoC: hdmi-codec: fix channel info for compressed formats")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20230929195027.97136-1-hias@horus.comSigned-off-by: Mark Brown <broonie@kernel.org>

On init we have sequence:

	for_each_card_prelinks(card, i, dai_link) {
		ret = snd_soc_add_pcm_runtime(card, dai_link);

	ret = init_some_other_things(...);
	if (ret)
		goto probe_end:

	for_each_card_rtds(card, rtd) {
		ret = soc_init_pcm_runtime(card, rtd);

probe_end:

while on exit:
	for_each_card_rtds(card, rtd)
		snd_soc_link_exit(rtd);

If init_some_other_things() step fails due to error we end up with
not fully setup rtds and try to call snd_soc_link_exit on them, which
depending on contents on .link_exit handler, can end up dereferencing
NULL pointer.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929103243.705433-2-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When printing log related to component it is useful to know, to which
component it applies to.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929103243.705433-1-amadeuszx.slawinski@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Setting ACP ACLK as clock source when ACP enters D0 state causing
firmware load failure as mentioned in below scenario.

- Load snd_sof_amd_rembrandt
- Play or Record audio
- Stop audio
- Unload snd_sof_amd_rembrandt
- Reload snd_sof_amd_rembrandt

If acp_clkmux_sel register field is set, then clock source will be
set to ACP ACLK when ACP enters D0 state.

During stream stop, if there is no active stream is running then
acp firmware will set the ACP ACLK value to zero.

When driver is reloaded and clock source is selected as ACP ACLK,
as ACP ACLK is programmed to zero, firmware loading will fail.

For RMB platform, remove the clock mux selection field so that
ACP will use internal clock source when ACP enters D0 state.

Fixes: 41cb85bc ("ASoC: SOF: amd: Add support for Rembrandt plaform.")
Reported-by: coolstar <coolstarorganization@gmail.com>
Closes: https://github.com/thesofproject/sof/issues/8137Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230927071412.2416250-1-Vijendar.Mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

As the pll_id and pll_id can be zero (WM8960_SYSCLK_AUTO)
with the commit 2bbc2df4 ("ASoC: wm8960: Make automatic the
default clocking mode")

Then the machine driver will skip to call set_sysclk() and set_pll()
for codec, when the sysclk rate is different with what wm8960 read
at probe, the output sound frequency is wrong.

So change the fll_id and pll_id initial value, still keep machine
driver's behavior same as before.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695202992-24864-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

On i.MX8MP, the BCE and TERE bit are binding with mclk
enablement, if BCE and TERE are cleared the MCLK also be
disabled on output pin, that cause the external codec (wm8960)
in wrong state.

Codec (wm8960) is using the mclk to generate PLL clock,
if mclk is disabled before disabling PLL, the codec (wm8960)
won't generate bclk and frameclk when sysclk switch to
MCLK source in next test case.

The test case:
$aplay -r44100 test1.wav (PLL source)
$aplay -r48000 test2.wav (MCLK source)
aplay: pcm_write:2127: write error: Input/output error

Fixes: 269f399d ("ASoC: fsl_sai: Disable bit clock with transmitter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695116533-23287-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add compatible for RK3128's S/PDIF.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230829171647.187787-4-knaerzche@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

While browsing/grepping in the sound core, I found that
snd_dmaengine_set_config_from_dai_data() did not exist, in favor of
snd_dmaengine_pcm_set_config_from_dai_data(). Fix the typo.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922161547.594484-1-miquel.raynal@bootlin.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:

Adding Es83x6 codec entry and HDMI-in capture support in MTL match table.

asoc_simple_probe() is used for both "DT probe" (A) and "platform probe"
(B). It uses "goto err" when error case, but it is not needed for
"platform probe" case (B). Thus it is using "return" directly there.

	static int asoc_simple_probe(...)
	{
 ^		if (...) {
 |			...
(A)			if (ret < 0)
 |				goto err;
 v		} else {
 ^			...
 |			if (ret < 0)
(B)				return -Exxx;
 v		}

		...
 ^		if (ret < 0)
(C)			goto err;
 v		...

	err:
(D)		simple_util_clean_reference(card);

		return ret;
	}

Both case are using (C) part, and it calls (D) when err case.
But (D) will do nothing for (B) case.
Because of these behavior, current code itself is not wrong,
but is confusable, and more, static analyzing tool will warning on
(B) part (should use goto err).

To avoid static analyzing tool warning, this patch uses "goto err"
on (B) part.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7hy7mlh.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

It should use "goto" instead of "return"

Fixes: 5ca2ab45 ("ASoC: simple-card-utils: Add new system-clock-fixed flag")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/202309141205.ITZeDJxV-lkp@intel.com/
Closes: https://lore.kernel.org/all/202309151840.au9Aa2W4-lkp@intel.com/Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8c76jnz.wl-kuninori.morimoto.gx@renesas.comSigned-off-by: Mark Brown <broonie@kernel.org>

One more missing SKU in the list.

Closes: https://github.com/thesofproject/linux/issues/4543Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919092125.1922468-1-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The rule for the SoundWire tables is that the platforms with more
devices need to be added first. We broke that rule with the Dell SKU
0B34, and caused the second amplifier for SKU 0AF3 to be ignored.

The fix is simple, we need to move the single-amplifier entry after
the two-amplifier one.

Fixes: b62a1a83 ("ASoC: Intel: soc-acpi: add tables for Dell SKU 0B34")
Closes: https://github.com/thesofproject/linux/issues/4559Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919083606.1920202-1-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Adding HDMI-In capture via I2S feature support in MTL platform.
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-3-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Adding support for ES83x6 codec in MTL match table.
Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-2-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

All the fail paths during probe will free up the ops, on remove we should
only free it if the probe was successful.

Fixes: bc433fd7 ("ASoC: SOF: Add ops_free")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20230915124015.19637-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

20s seems unnecessarily large for the DSP init timeout. This coupled with
multiple FW boot attempts causes an excessive delay in the error path when
booting in recovery mode. Reduce it to 0.5s and use the existing
HDA_DSP_INIT_TIMEOUT_US.

Link: https://github.com/thesofproject/linux/issues/4565Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230915134153.9688-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The microphone and speaker shutters on cs42l43 can be configured to
trigger from the same GPIO, in this case the current code returns an
error as we attempt to request two IRQ handlers for the same IRQ. Fix
this by always requesting the shutter IRQs with the IRQF_SHARED flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230915144300.120100-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The devm_clk_get() can return -EPROBE_DEFER error,
modify the error code to be -EINVAL is not correct, which
cause the -EPROBE_DEFER error is not correctly handled.

This patch is to fix the return error code.

Fixes: b86ef536 ("ASoC: fsl: Add Audio Mixer machine driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1694757731-18308-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Because of the potential failure of the devm_kstrdup(), the
dl[i].codecs->name could be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.

Fixes: 97030a43 ("ASoC: Intel: avs: Add HDAudio machine board")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230915021344.3078-1-nichen@iscas.ac.cnSigned-off-by: Mark Brown <broonie@kernel.org>

In case the widget setup fails we should only decrement the core usage
count if the sof_widget_free_unlocked() has not been called as part of
the error handling.
sof_widget_free_unlocked() calls snd_sof_dsp_core_put() and the additional
core_put will cause imbalance in core usage count.
Use the existing use_count_decremented to handle this issue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230914124725.17397-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

available_fmt is a pointer.

Fixes: 4fdef47a ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230914132504.18463-1-peter.ujfalusi@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

i.MX rpmsg sound cards work on codec slave mode. MCLK will be disabled
by CPU DAI driver in hw_free(). Some codec requires MCLK present at
power up/down sequence. So need to set ignore_pmdown_time to power down
codec immediately before MCLK is turned off.

Take WM8962 as an example, if MCLK is disabled before DAPM power down
playback stream, FIFO error will arise in WM8962 which will have bad
impact on playback next.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230913102656.2966757-1-chancel.liu@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:

These patches fix 3 problems with hard reset:
1. Ensure a minimum reset pulse width
2. Deal with ACPI overriding the requested default GPIO state
3. Avoid a race condition when hard-resetting a SoundWire peripheral
   that is already enumerated

wm_adsp_read_ctl() and wm_adsp_write_ctl() must hold the cs_dsp pwr_lock
mutex when calling cs_dsp_coeff_read_ctrl() and cs_dsp_coeff_write_ctrl().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160250.3700346-1-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Change the logging of each algorithm from info level to debug level.

On the original devices supported by this code there were typically only
one or two algorithms in a firmware and one or two DSPs so this logging
only used a small number of log lines.

However, for the latest devices there could be 30-40 algorithms in a
firmware and 8 DSPs being loaded in parallel, so using 300+ lines of log
for information that isn't particularly important to have logged.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160523.3701189-1-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

In SoundWire mode leave hard RESET asserted when exiting probe,
and wait for an UNATTACHED notification before deasserting RESET.

If the boot state of the reset GPIO was deasserted it is possible
that the SoundWire core had already enumerated the CS42L42 before
cs42l42_sdw_probe() is called. When cs42l42_common_probe() hard
resets the CS42L42 it triggers a race condition:

1) After cs42l42_sdw_probe() returns the thread that called it
   will call cs42l42_sdw_update_status() to report the last
   status recorded by the SoundWire core.

2) The SoundWire bus master will see a PING with the CS42L42
   now reporting as unenumerated and will trigger the core
   SoundWire code to start enumerating CS42L42.

These two threads are racing against each other. If (1)
happens before (2) a stale ATTACHED notification will be
reported to the cs42l42 driver when in fact the status of
cs42l42 is now unattached.

To avoid this race condition:

- Leave RESET asserted on exit from cs42l42_sdw_probe().
  This ensures that an UNATTACHED notification must be
  sent to the cs42l42 driver. If cs42l42 was already
  enumerated it will be seen to drop off the bus, causing
  an UNATTACH notification. If it was never enumerated the
  status is already UNATTACHED and this will be reported
  by thread (1).

- When the UNATTACH notification is received, release RESET.
  This will cause CS42L42 to be enumerated and eventually
  report an ATTACHED notification.

- The ATTACHED notification is now valid.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-4-sbinding@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The ACPI setting for a GPIO default state has higher priority than the
flag passed to devm_gpiod_get_optional() so ACPI can override the
GPIOD_OUT_LOW. Explicitly set the GPIO low when hard resetting.

Although GPIOD_OUT_LOW can't be relied on this doesn't seem like a
reason to stop passing it to devm_gpiod_get_optional(). So we still pass
it to state our intent, but can deal with it having no effect.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-3-sbinding@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The CS42L42 can accept very short reset pulses of a few microseconds
but there's no reason to force a very short pulse.
Allow a wide range for the usleep_range() so it can be relaxed about
the choice of timing source.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-2-sbinding@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

These error paths should return -EINVAL instead of success.

Fixes: 7f4ec778 ("ASoC: codecs: Add code for bin parsing compatible with aw88261")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/81476e78-05c2-4656-b754-f314c7ccdb81@moroto.mountainSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Hans de Goede <hdegoede@redhat.com>:

The recent(ish) rt5640 changes to add HDA header jack-detect support
and the related suspend/resume handling fixes have introduced several
issues with IRQ handling on boards not using the HDA header jack-detect
support.

This series fixes these issues, see the individual commit messages
for details.

Do not allow the CS35L56 to be put into its lowest power
"hibernation" mode. This only affects I2C because "hibernation"
is already disabled on SPI and SoundWire.

Recent firmwares need a different wake-up sequence. Until
that sequence has been specified, the chip "hibernation" mode
must be disabled otherwise it can intermittently fail to wake.

THIS WILL NOT APPLY CLEANLY TO 6.5 AND EARLIER:
We will send a separate backport patch to stable.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230912133841.3480466-1-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

If jack-detection is not used; or has already been disabled then
there is no need to call rt5640_cancel_work().

Move the rt5640_cancel_work() inside the "if (rt5640->jack) {}" block,
grouping it together with the disabling of the IRQ which queues the work
in the first place.

This also makes suspend() symetrical with resume() which re-queues the work
in an "if (rt5640->jack) {}" block.

Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-7-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Set "rt5640->irq_requested = true" after a successful request_irq()
in rt5640_enable_hda_jack_detect(), so that rt5640_disable_jack_detect()
properly frees the IRQ.

This fixes the IRQ not being freed on rmmod / driver unbind.

Fixes: 2b9c8d2b ("ASoC: rt5640: Add the HDA header support")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-6-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

The jack-detect IRQ should be enabled *after* the jack-detect related
configuration registers have been programmed.

Move the enable_irq() call for this to after the register setup.

Fixes: 5fabcc90 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-5-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

When jack-detect was originally added disabling the IRQ during suspend
was done by the sound/soc/intel/boards/bytcr_rt5640.c driver
calling snd_soc_component_set_jack(NULL) on suspend, which calls
rt5640_disable_jack_detect(), which calls free_irq() which also
disables it.

Commit 5fabcc90 ("ASoC: rt5640: Fix Jack work after system suspend")
added disable_irq() / enable_irq() calls on suspend/resume for machine
drivers which do not call snd_soc_component_set_jack(NULL) on suspend.

The new disable_irq() / enable_irq() are made conditional by
"if (rt5640->irq)" statements, but this is true for the machine drivers
which do call snd_soc_component_set_jack(NULL) on suspend too, causing
a disable_irq() call there on the already free-ed IRQ.

Change the "if (rt5640->irq)" condition to "if (rt5640->jack)" to fix this,
rt5640->jack is only set if the jack-detect IRQ handler is still active
when rt5640_suspend() runs.

And adjust rt5640_enable_hda_jack_detect()'s request_irq() error handling
to set rt5640->jack to NULL to match (note that the old setting of irq to
-ENOXIO still resulted in disable_irq(-ENOXIO) calls on suspend).

Fixes: 5fabcc90 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-4-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Following prints are observed while testing audio on Jetson AGX Orin which
has onboard RT5640 audio codec:

  BUG: sleeping function called from invalid context at kernel/workqueue.c:3027
  in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
  preempt_count: 10001, expected: 0
  RCU nest depth: 0, expected: 0
  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1e0/0x270
  ---[ end trace ad1c64905aac14a6 ]-

The IRQ handler rt5640_irq() runs in interrupt context and can sleep
during cancel_delayed_work_sync().

The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
avoiding the sleep in atomic context.

Fixes: 051dade3 ("ASoC: rt5640: Fix the wrong state of JD1 and JD2")
Reported-by: Sameer Pujar <spujar@nvidia.com>
Closes: https://lore.kernel.org/r/1688015537-31682-4-git-send-email-spujar@nvidia.com
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-3-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Commit 70a6404f ("ASoC: rt5640: Fix sleep in atomic context")
not only switched from request_irq() to request_threaded_irq(),
to fix the sleep in atomic context issue, but it also added
devm management of the IRQ by actually switching to
devm_request_threaded_irq() (without any explanation in the commit
message for this change).

This is wrong since the IRQ was already explicitly managed by
the driver. On unbind the ASoC core will call rt5640_set_jack(NULL)
which in turn will call rt5640_disable_jack_detect() which
frees the IRQ already. So now we have a double free.

Besides the unexplained switch to devm being wrong, the actual fix
for the sleep in atomic context issue also is not the best solution.

The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
which does not sleep. Using mod_delayed_work() is a much better fix
then adding a thread which does nothing other then queuing a work-item.

This patch is a straight revert of the troublesome changes, the switch
to mod_delayed_work() is done in a separate follow-up patch.

Fixes: 70a6404f ("ASoC: rt5640: Fix sleep in atomic context")
Cc: Sameer Pujar <spujar@nvidia.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-2-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Like the Lenovo 82TL and 82V2, the Lenovo 82QF (Yoga 7 14ARB7) and 82UG
(Legion S7 16ARHA7) both need a quirk entry for the internal microphone to
function. Commit c008323f ("ASoC: amd: yc: Fix a non-functional mic on
Lenovo 82SJ") restricted the quirk that previously matched "82" to "82V2",
breaking microphone functionality on these devices. Fix this by adding
specific quirks for these models, as was done for the Lenovo 82TL.

Fixes: c008323f ("ASoC: amd: yc: Fix a non-functional mic on Lenovo 82SJ")
Closes: https://github.com/tomsom/yoga-linux/issues/51
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208555#c780
Cc: stable@vger.kernel.org
Signed-off-by: August Wikerfors <git@augustwikerfors.se>
Link: https://lore.kernel.org/r/20230911213409.6106-1-git@augustwikerfors.seSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Sameer Pujar <spujar@nvidia.com>:

This small series fixes redundant PLLA updates that happen for
each DAI link in the audio path. This helps to resolve DMIC clock
issue seen on Jetson TX2 platform.