This patch fixes two race conditions between bond_store_updelay/downdelay
and bond_store_miimon which could lead to division by zero as miimon can
be set to 0 while either updelay/downdelay are being set and thus miss the
zero check in the beginning, the zero div happens because updelay/downdelay
are stored as new_value / bond->params.miimon. Use rtnl to synchronize with
miimon setting.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit c9eeec26 ("tcp: TSQ can use a dynamic limit"), several
users reported throughput regressions, notably on mvneta and wifi
adapters.

802.11 AMPDU requires a fair amount of queueing to be effective.

This patch partially reverts the change done in tcp_write_xmit()
so that the minimal amount is sysctl_tcp_limit_output_bytes.

It also remove the use of this sysctl while building skb stored
in write queue, as TSO autosizing does the right thing anyway.

Users with well behaving NICS and correct qdisc (like sch_fq),
can then lower the default sysctl_tcp_limit_output_bytes value from
128KB to 8KB.

This new usage of sysctl_tcp_limit_output_bytes permits each driver
authors to check how their driver performs when/if the value is set
to a minimum of 4KB.

Normally, line rate for a single TCP flow should be possible,
but some drivers rely on timers to perform TX completion and
too long TX completion delays prevent reaching full throughput.

Fixes: c9eeec26 ("tcp: TSQ can use a dynamic limit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
net_tstamp: Validate hwtstamp_config completely before applying it

This series fixes very similar bugs in 6 implementations of
SIOCSHWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes.  Currently it sets the TX configuration
before validating the rx_filter field.

Untested as I don't have a cross-compiler to hand.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cpsw_hwtstamp_ioctl() should validate all fields of hwtstamp_config,
and the hardware version, before making any changes.  Currently it
sets the TX configuration before validating the rx_filter field
or that the hardware supports timestamping.

Also correct the error code for hardware versions that don't
support timestamping.  ENOTSUPP is used by the NFS implementation
and is not part of userland API; we want EOPNOTSUPP (which glibc
also calls ENOTSUP, with one 'P').

Untested as I don't have a cross-compiler to hand.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stmmac_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes.  Currently it sets the TX configuration
before validating the rx_filter field.

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes.  Currently it sets the TX configuration
before validating the rx_filter field.

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes.  Currently it copies the configuration to
the e1000_adapter structure before validating it at all.

Change e1000e_config_hwtstamp() to take a pointer to the
hwstamp_config and to copy the config after validating it.

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes.  Currently it sets the TX configuration
before validating the rx_filter field.

Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently don't call br_vlan_flush() when deleting a bridge, which
leads to memory leak if br->vlan_info is allocated.

Steps to reproduce:
  while :
  do
    brctl addbr br0
    bridge vlan add dev br0 vid 10 self
    brctl delbr br0
  done
We can observe the cache size of corresponding slab entry
(as kmalloc-2048 in SLUB) is increased.

kmemleak output:
unreferenced object 0xffff8800b68a7000 (size 2048):
  comm "bridge", pid 2086, jiffies 4295774704 (age 47.656s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 48 9b 36 00 88 ff ff  .........H.6....
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff815eb6ae>] kmemleak_alloc+0x4e/0xb0
    [<ffffffff8116a1ca>] kmem_cache_alloc_trace+0xca/0x220
    [<ffffffffa03eddd6>] br_vlan_add+0x66/0xe0 [bridge]
    [<ffffffffa03e543c>] br_setlink+0x2dc/0x340 [bridge]
    [<ffffffff8150e481>] rtnl_bridge_setlink+0x101/0x200
    [<ffffffff8150d9d9>] rtnetlink_rcv_msg+0x99/0x260
    [<ffffffff81528679>] netlink_rcv_skb+0xa9/0xc0
    [<ffffffff8150d938>] rtnetlink_rcv+0x28/0x30
    [<ffffffff81527ccd>] netlink_unicast+0xdd/0x190
    [<ffffffff8152807f>] netlink_sendmsg+0x2ff/0x740
    [<ffffffff814e8368>] sock_sendmsg+0x88/0xc0
    [<ffffffff814e8ac8>] ___sys_sendmsg.part.14+0x298/0x2b0
    [<ffffffff814e91de>] __sys_sendmsg+0x4e/0x90
    [<ffffffff814e922e>] SyS_sendmsg+0xe/0x10
    [<ffffffff81601669>] system_call_fastpath+0x16/0x1b
    [<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should call vlan_vid_del for all vids at nbp_vlan_flush to prevent
vid_info->refcount from being leaked when detaching a bridge port.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should use wrapper functions vlan_vid_[add/del] instead of
ndo_vlan_rx_[add/kill]_vid. Otherwise, we might be not able to communicate
using vlan interface in a certain situation.

Example of problematic case:
  vconfig add eth0 10
  brctl addif br0 eth0
  bridge vlan add dev eth0 vid 10
  bridge vlan del dev eth0 vid 10
  brctl delif br0 eth0
In this case, we cannot communicate via eth0.10 because vlan 10 is
filtered by NIC that has the vlan filtering feature.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use msecs_to_jiffies, for these calculations as different HZ
considerations are taken into account for conversion of the timer
shot, and also it makes the code more readable.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We only call that in functions annotated with __init, so add __init
prefix in prandom_start_seed_timer() as well, so that the kernel can
make use of this hint and we can possibly free up resources after it's
usage. And since it's an internal function rename it to
__prandom_start_seed_timer().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently use hdr_len as a hint of head length which is advertised by
guest. But when guest advertise a very big value, it can lead to an 64K+
allocating of kmalloc() which has a very high possibility of failure when host
memory is fragmented or under heavy stress. The huge hdr_len also reduce the
effect of zerocopy or even disable if a gso skb is linearized in guest.

To solves those issues, this patch introduces an upper limit (PAGE_SIZE) of the
head, which guarantees an order 0 allocation each time.

Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently use hdr_len as a hint of head length which is advertised by
guest. But when guest advertise a very big value, it can lead to an 64K+
allocating of kmalloc() which has a very high possibility of failure when host
memory is fragmented or under heavy stress. The huge hdr_len also reduce the
effect of zerocopy or even disable if a gso skb is linearized in guest.

To solves those issues, this patch introduces an upper limit (PAGE_SIZE) of the
head, which guarantees an order 0 allocation each time.

Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We assume that "mp->phy" can be NULL a couple lines before the
dereference.

Fixes: 1cce16d3 ('net: mv643xx_eth: Add missing phy_addr_set in DT mode')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is harmless but cdc_ncm_setup() returns negative error codes
truncated to u8 values.  There is only one caller and treats all
non-zero returns as errors but doesn't store the the return code.  So
the code works correctly but it's messy and upsets the static checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 06a23fe3
("core/dev: set pkt_type after eth_type_trans() in dev_forward_skb()")
and refactoring 64261f23
("dev: move skb_scrub_packet() after eth_type_trans()")

are forcing pkt_type to be PACKET_HOST when skb traverses veth.

which means that ip forwarding will kick in inside netns
even if skb->eth->h_dest != dev->dev_addr

Fix order of eth_type_trans() and skb_scrub_packet() in dev_forward_skb()
and in ip_tunnel_rcv()

Fixes: 06a23fe3 ("core/dev: set pkt_type after eth_type_trans() in dev_forward_skb()")
CC: Isaku Yamahata <yamahatanetdev@gmail.com>
CC: Maciej Zenczykowski <zenczykowski@gmail.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 7b0c5f21
"sierra_net: keep status interrupt URB active", sierra_net triggers
status interrupt polling before the net_device is opened (in order to
properly receive the sync message response).

To be able to receive further interrupts, the interrupt urb needs to be
re-submitted, so this patch removes the bogus check for netif_running().
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the ARP monitoring is not supported with 802.3ad, and it's
prohibited to use it via the module params.

However we still can set it afterwards via sysfs, cause we only check for
*LB modes there.

To fix this - add a check for 802.3ad mode in bonding_store_arp_interval.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Santosh raspatur is taking over the maintenance of cxgb3.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking updates from David Miller:

 1) The addition of nftables.  No longer will we need protocol aware
    firewall filtering modules, it can all live in userspace.

    At the core of nftables is a, for lack of a better term, virtual
    machine that executes byte codes to inspect packet or metadata
    (arriving interface index, etc.) and make verdict decisions.

    Besides support for loading packet contents and comparing them, the
    interpreter supports lookups in various datastructures as
    fundamental operations.  For example sets are supports, and
    therefore one could create a set of whitelist IP address entries
    which have ACCEPT verdicts attached to them, and use the appropriate
    byte codes to do such lookups.

    Since the interpreted code is composed in userspace, userspace can
    do things like optimize things before giving it to the kernel.

    Another major improvement is the capability of atomically updating
    portions of the ruleset.  In the existing netfilter implementation,
    one has to update the entire rule set in order to make a change and
    this is very expensive.

    Userspace tools exist to create nftables rules using existing
    netfilter rule sets, but both kernel implementations will need to
    co-exist for quite some time as we transition from the old to the
    new stuff.

    Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
    worked so hard on this.

 2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
    to our pseudo-random number generator, mostly used for things like
    UDP port randomization and netfitler, amongst other things.

    In particular the taus88 generater is updated to taus113, and test
    cases are added.

 3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
    and Yang Yingliang.

 4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
    Sujir.

 5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
    Neal Cardwell, and Yuchung Cheng.

 6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
    control message data, much like other socket option attributes.
    From Francesco Fusco.

 7) Allow applications to specify a cap on the rate computed
    automatically by the kernel for pacing flows, via a new
    SO_MAX_PACING_RATE socket option.  From Eric Dumazet.

 8) Make the initial autotuned send buffer sizing in TCP more closely
    reflect actual needs, from Eric Dumazet.

 9) Currently early socket demux only happens for TCP sockets, but we
    can do it for connected UDP sockets too.  Implementation from Shawn
    Bohrer.

10) Refactor inet socket demux with the goal of improving hash demux
    performance for listening sockets.  With the main goals being able
    to use RCU lookups on even request sockets, and eliminating the
    listening lock contention.  From Eric Dumazet.

11) The bonding layer has many demuxes in it's fast path, and an RCU
    conversion was started back in 3.11, several changes here extend the
    RCU usage to even more locations.  From Ding Tianhong and Wang
    Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
    Falico.

12) Allow stackability of segmentation offloads to, in particular, allow
    segmentation offloading over tunnels.  From Eric Dumazet.

13) Significantly improve the handling of secret keys we input into the
    various hash functions in the inet hashtables, TCP fast open, as
    well as syncookies.  From Hannes Frederic Sowa.  The key fundamental
    operation is "net_get_random_once()" which uses static keys.

    Hannes even extended this to ipv4/ipv6 fragmentation handling and
    our generic flow dissector.

14) The generic driver layer takes care now to set the driver data to
    NULL on device removal, so it's no longer necessary for drivers to
    explicitly set it to NULL any more.  Many drivers have been cleaned
    up in this way, from Jingoo Han.

15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.

16) Improve CRC32 interfaces and generic SKB checksum iterators so that
    SCTP's checksumming can more cleanly be handled.  Also from Daniel
    Borkmann.

17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
    using the interface MTU value.  This helps avoid PMTU attacks,
    particularly on DNS servers.  From Hannes Frederic Sowa.

18) Use generic XPS for transmit queue steering rather than internal
    (re-)implementation in virtio-net.  From Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
  random32: add test cases for taus113 implementation
  random32: upgrade taus88 generator to taus113 from errata paper
  random32: move rnd_state to linux/random.h
  random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
  random32: add periodic reseeding
  random32: fix off-by-one in seeding requirement
  PHY: Add RTL8201CP phy_driver to realtek
  xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
  macmace: add missing platform_set_drvdata() in mace_probe()
  ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
  ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
  vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
  ixgbe: add warning when max_vfs is out of range.
  igb: Update link modes display in ethtool
  netfilter: push reasm skb through instead of original frag skbs
  ip6_output: fragment outgoing reassembled skb properly
  MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
  net_sched: tbf: support of 64bit rates
  ixgbe: deleting dfwd stations out of order can cause null ptr deref
  ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
  ...

Merge first patch-bomb from Andrew Morton:
 "Quite a lot of other stuff is banked up awaiting further
  next->mainline merging, but this batch contains:

   - Lots of random misc patches
   - OCFS2
   - Most of MM
   - backlight updates
   - lib/ updates
   - printk updates
   - checkpatch updates
   - epoll tweaking
   - rtc updates
   - hfs
   - hfsplus
   - documentation
   - procfs
   - update gcov to gcc-4.7 format
   - IPC"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (269 commits)
  ipc, msg: fix message length check for negative values
  ipc/util.c: remove unnecessary work pending test
  devpts: plug the memory leak in kill_sb
  ./Makefile: export initial ramdisk compression config option
  init/Kconfig: add option to disable kernel compression
  drivers: w1: make w1_slave::flags long to avoid memory corruption
  drivers/w1/masters/ds1wm.cuse dev_get_platdata()
  drivers/memstick/core/ms_block.c: fix unreachable state in h_msb_read_page()
  drivers/memstick/core/mspro_block.c: fix attributes array allocation
  drivers/pps/clients/pps-gpio.c: remove redundant of_match_ptr
  kernel/panic.c: reduce 1 byte usage for print tainted buffer
  gcov: reuse kbasename helper
  kernel/gcov/fs.c: use pr_warn()
  kernel/module.c: use pr_foo()
  gcov: compile specific gcov implementation based on gcc version
  gcov: add support for gcc 4.7 gcov format
  gcov: move gcov structs definitions to a gcc version specific file
  kernel/taskstats.c: return -ENOMEM when alloc memory fails in add_del_listener()
  kernel/taskstats.c: add nla_nest_cancel() for failure processing between nla_nest_start() and nla_nest_end()
  kernel/sysctl_binary.c: use scnprintf() instead of snprintf()
  ...

Pull vfs updates from Al Viro:
 "All kinds of stuff this time around; some more notable parts:

   - RCU'd vfsmounts handling
   - new primitives for coredump handling
   - files_lock is gone
   - Bruce's delegations handling series
   - exportfs fixes

  plus misc stuff all over the place"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
  ecryptfs: ->f_op is never NULL
  locks: break delegations on any attribute modification
  locks: break delegations on link
  locks: break delegations on rename
  locks: helper functions for delegation breaking
  locks: break delegations on unlink
  namei: minor vfs_unlink cleanup
  locks: implement delegations
  locks: introduce new FL_DELEG lock flag
  vfs: take i_mutex on renamed file
  vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
  vfs: don't use PARENT/CHILD lock classes for non-directories
  vfs: pull ext4's double-i_mutex-locking into common code
  exportfs: fix quadratic behavior in filehandle lookup
  exportfs: better variable name
  exportfs: move most of reconnect_path to helper function
  exportfs: eliminate unused "noprogress" counter
  exportfs: stop retrying once we race with rename/remove
  exportfs: clear DISCONNECTED on all parents sooner
  exportfs: more detailed comment for path_reconnect
  ...

Pull dlm fix from David Teigland:
 "This set includes a single fix to resolve to a race that could cause
  lockspace shutdown to incorrectly return -EBUSY"

* tag 'dlm-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
  dlm: Avoid that dlm_release_lockspace() incorrectly returns -EBUSY

Pull UBI changes from Artem Bityutskiy:
 "A bunch of fixes for the fastmap feature, which is still new and
  rather experimental.  It looks like it starts getting more users.

  No significant changes for the "classical" non-fastmap UBI"

* tag 'upstream-3.13-rc1' of git://git.infradead.org/linux-ubi:
  UBI: Add some asserts to ubi_attach_fastmap()
  UBI: Fix memory leak in ubi_attach_fastmap() error path
  UBI: simplify image sequence test
  UBI: fastmap: fix backward compatibility with image_seq
  UBI: Call scan_all() with correct offset in error case
  UBI: Fix error path in scan_pool()
  UBI: fix refill_wl_user_pool()

Pull ubifs changes from Artem Bityutskiy:
 "Mostly fixes for the power cut emulation UBIFS mode, and only one
  functional change which fixes a return error code"

* tag 'upstream-3.13-rc1' of git://git.infradead.org/linux-ubifs:
  UBIFS: correct data corruption range
  UBIFS: fix return code
  UBIFS: remove unnecessary code in ubifs_garbage_collect

Pull fuse updates from Miklos Szeredi:
 "This adds a ->writepage() implementation to fuse, improving mmaped
  writeout and paving the way for buffered writeback.

  And there's a patch to add a fix minor number for /dev/cuse, similarly
  to /dev/fuse"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: writepages: protect secondary requests from fuse file release
  fuse: writepages: update bdi writeout when deleting secondary request
  fuse: writepages: crop secondary requests
  fuse: writepages: roll back changes if request not found
  cuse: add fix minor number to /dev/cuse
  fuse: writepage: skip already in flight
  fuse: writepages: handle same page rewrites
  fuse: writepages: fix aggregation
  fuse: fix race in fuse_writepages()
  fuse: Implement writepages callback
  fuse: don't BUG on no write file
  fuse: lock page in mkwrite
  fuse: Prepare to handle multiple pages in writeback
  fuse: Getting file for writeback helper

Pull ext[23], udf and quota fixes from Jan Kara:
 "Assorted fixes in quota, ext2, ext3 & udf.

  Probably the most important is a fix of fs corruption issue in ext2
  XIP support (OTOH xip is rarely used)"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  ext2: Fix fs corruption in ext2_get_xip_mem()
  quota: info leak in quota_getquota()
  jbd: Revert "jbd: remove dependency on __GFP_NOFAIL"
  udf: fix for pathetic mount times in case of invalid file system
  ext3: Count journal as bsddf overhead in ext3_statfs

Pull f2fs updates from Jaegeuk Kim:
 "This patch-set includes the following major enhancement patches.
   - add a sysfs to control reclaiming free segments
   - enhance the f2fs global lock procedures
   - enhance the victim selection flow
   - wait for selected node blocks during fsync
   - add some tracepoints
   - add a config to remove abundant BUG_ONs

  The other bug fixes are as follows.
   - fix deadlock on acl operations
   - fix some bugs with respect to orphan inodes

  And, there are a bunch of cleanups"

* tag 'for-f2fs-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (42 commits)
  f2fs: issue more large discard command
  f2fs: fix memory leak after kobject init failed in fill_super
  f2fs: cleanup waiting routine for writeback pages in cp
  f2fs: avoid to use a NULL point in destroy_segment_manager
  f2fs: remove unnecessary TestClearPageError when wait pages writeback
  f2fs: update f2fs document
  f2fs: avoid to wait all the node blocks during fsync
  f2fs: check all ones or zeros bitmap with bitops for better mount performance
  f2fs: change the method of calculating the number summary blocks
  f2fs: fix calculating incorrect free size when update xattr in __f2fs_setxattr
  f2fs: add an option to avoid unnecessary BUG_ONs
  f2fs: introduce CONFIG_F2FS_CHECK_FS for BUG_ON control
  f2fs: fix a deadlock during init_acl procedure
  f2fs: clean up acl flow for better readability
  f2fs: remove unnecessary segment bitmap updates
  f2fs: add tracepoint for vm_page_mkwrite
  f2fs: add tracepoint for set_page_dirty
  f2fs: remove redundant set_page_dirty from write_compacted_summaries
  f2fs: add reclaiming control by sysfs
  f2fs: introduce f2fs_balance_fs_bg for some background jobs
  ...

Pull cgroup changes from Tejun Heo:
 "Not too much activity this time around.  css_id is finally killed and
  a minor update to device_cgroup"

* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  device_cgroup: remove can_attach
  cgroup: kill css_id
  memcg: stop using css id
  memcg: fail to create cgroup if the cgroup id is too big
  memcg: convert to use cgroup id
  memcg: convert to use cgroup_is_descendant()

Pull libata changes from Tejun Heo:
 "Nothing too interesting.  Only two minor fixes in libata core.  Most
  changes are specific to hardware which isn't too common"

* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: Add Device IDs for Intel Wildcat Point-LP
  sata_rcar: Convert to clk_prepare/unprepare
  drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH drive
  libata: Add some missing command descriptions
  sata_highbank: clear whole array in highbank_initialize_phys()
  ahci: disabled FBS prior to issuing software reset
  libata: Fix display of sata speed
  ahci: imx: setup power saving methods
  ata_piix: minor typo and a printk fix
  ahci: Changing two module params with static and __read_mostly

Pull percpu changes from Tejun Heo:
 "Two smallish changes for percpu.  Two patches to remove unused
  this_cpu_xor() and one to fix a bug in percpu init failure path so
  that it can reach the proper BUG() instead of oopsing earlier"

* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  x86: remove this_cpu_xor() implementation
  percpu: remove this_cpu_xor() implementation
  percpu: fix bootmem error handling in pcpu_page_first_chunk()

On 64 bit systems the test for negative message sizes is bogus as the
size, which may be positive when evaluated as a long, will get truncated
to an int when passed to load_msg().  So a long might very well contain a
positive value but when truncated to an int it would become negative.

That in combination with a small negative value of msg_ctlmax (which will
be promoted to an unsigned type for the comparison against msgsz, making
it a big positive value and therefore make it pass the check) will lead to
two problems: 1/ The kmalloc() call in alloc_msg() will allocate a too
small buffer as the addition of alen is effectively a subtraction.  2/ The
copy_from_user() call in load_msg() will first overflow the buffer with
userland data and then, when the userland access generates an access
violation, the fixup handler copy_user_handle_tail() will try to fill the
remainder with zeros -- roughly 4GB.  That almost instantly results in a
system crash or reset.

  ,-[ Reproducer (needs to be run as root) ]--
  | #include <sys/stat.h>
  | #include <sys/msg.h>
  | #include <unistd.h>
  | #include <fcntl.h>
  |
  | int main(void) {
  |     long msg = 1;
  |     int fd;
  |
  |     fd = open("/proc/sys/kernel/msgmax", O_WRONLY);
  |     write(fd, "-1", 2);
  |     close(fd);
  |
  |     msgsnd(0, &msg, 0xfffffff0, IPC_NOWAIT);
  |
  |     return 0;
  | }
  '---

Fix the issue by preventing msgsz from getting truncated by consistently
using size_t for the message length.  This way the size checks in
do_msgsnd() could still be passed with a negative value for msg_ctlmax but
we would fail on the buffer allocation in that case and error out.

Also change the type of m_ts from int to size_t to avoid similar nastiness
in other code paths -- it is used in similar constructs, i.e.  signed vs.
unsigned checks.  It should never become negative under normal
circumstances, though.

Setting msg_ctlmax to a negative value is an odd configuration and should
be prevented.  As that might break existing userland, it will be handled
in a separate commit so it could easily be reverted and reworked without
reintroducing the above described bug.

Hardening mechanisms for user copy operations would have catched that bug
early -- e.g.  checking slab object sizes on user copy operations as the
usercopy feature of the PaX patch does.  Or, for that matter, detect the
long vs.  int sign change due to truncation, as the size overflow plugin
of the very same patch does.

[akpm@linux-foundation.org: fix i386 min() warnings]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Pax Team <pageexec@freemail.hu>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>	[ v2.3.27+ -- yes, that old ;) ]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove unnecessary work pending test before calling schedule_work().  It
has been tested in queue_work_on() already.  No functional changed.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Cc: Tejun Heo <tj@kernel.org>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When devpts is unmounted, there may be a no-longer-used IDR tree hanging
off the superblock we are about to kill.  This needs to be cleaned up
before destroying the SB.

The leak is usually not a big deal because unmounting devpts is typically
done when shutting down the whole machine.  However, shutting down an LXC
container instead of a physical machine exposes the problem (the garbage
is detectable with kmemleak).
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Make menuconfig allows one to choose compression format of an initial
ramdisk image.  But this choice does not result in duly compressed ramdisk
image.  Because - $ make install - does not pass on the selected
compression choice to the dracut(8) tool, which creates the initramfs
file.  dracut(8) generates the image with the default compression, ie.
gzip(1).

This patch exports the selected compression option to a sub-shell
environment, so that it could be used by dracut(8) tool to generate
appropriately compressed initramfs images.

There isn't a straightforward way to pass on options to dracut(8) via
positional parameters.  Because it is indirectly invoked at the end of a $
make install sequence.

 # make install
   -> arch/$arch/boot/Makefile
    -> arch/$arch/boot/install.sh
     -> /sbing/installkernel ...
      -> /sbin/new-kernel-pkg ...
       -> /sbin/dracut ...
Signed-off-by: P J P <ppandit@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some ARC users say they can boot faster with without kernel compression.
This probably depends on things like the FLASH chip they use etc.

Until now, kernel compression can only be disabled by removing "select
HAVE_<compression>" lines from the architecture Kconfig.  So add the
Kconfig logic to permit disabling of kernel compression.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On architectures where long is more then 32 bits, modifying a 32-bit field
with set_bit (and other atomic bit operations) may cause bytes following
the field to by modified.

Because the endianness of the bits within a field is the native endianness
of the CPU[1], on big-endian machines, bit number zero is in the last byte
of the field.

Therefore, `set_bit(0, ptr)' on a 64-bit big-endian machine is roughly
equivalent to `((char *)ptr)[7] |= 1', and since w1 driver uses a 32-bit
field for holding the flags, this causes bytes beyond the field to be
modified.

[1] From Documentation/atomic_ops.txt:

    Native atomic bit operations are defined to operate on objects
    aligned to the size of an "unsigned long" C data type, and are
    least of that size.  The endianness of the bits within each
    "unsigned long" are the native endianness of the cpu.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>