This patch updates copyrights and updates the tg3 version to 3.117.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a preprocessor naming bug for one of the EEE registers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a problem where EEE will fail to work in certain
environments.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

EEE interferes with the hardware's ability to loop a packet back to the
host.  This patch disables the feature for the duration of the test.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On CPMU devices, the MAC loopback test does not test any important paths
the phy loopback test doesn't also test.  The phy loopback test is the
more comprehensive test.  This patch disables the MAC loopback test for
these devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The half-duplex bit in the MAC MODE register will be set during the
loopback test if the external link is in half-duplex mode.  This will
cause the loopback test to fail on newer devices.  This patch turns the
half-duplex bit off for the test.

Also, newer devices fail the internal phy loopback test because the phy
link takes a little while to come up.  This patch adds code to wait for
the link before proceeding with the test.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If management firmware is present and the device is down, the firmware
will assume control of the phy.  If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior.  This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For single vector MSI-X allocations, we do not want to enable
multivector modes.  This patch makes the necessary corrections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch pivots the tg3 driver to the new VLAN infrastructure.
All references to vlgrp have been removed.  The driver still attempts to
disable VLAN tag stripping if CONFIG_VLAN_8021Q or
CONFIG_VLAN_8021Q_MODULE is not defined.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 5719 A0 has a bug that manifests itself as if the chipset were
reordering memory writes.  The best known way to solve this problem is
to turn off LSO and jumbo frames.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit cf79003d, entitled
"tg3: Fix 5719 internal FIFO overflow problem", proposed a way to solve
an internal FIFO overflow problem.  We have since discovered a slightly
better way to solve the problem.  This patch changes the code so that
the problem is contained closer to the problem source.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We spend lot of time clearing pages in pktgen.
(Or not clearing them on ipv6 and leaking kernel memory)

Since we dont modify them, we can use one zeroed page, and get
references on it. This page can use NUMA affinity as well.

Define pktgen_finalize_skb() helper, used both in ipv4 and ipv6

Results using skbs with one frag :

Before patch :

Result: OK: 608980458(c608978520+d1938) nsec, 1000000000
(100byte,1frags)
  1642088pps 1313Mb/sec (1313670400bps) errors: 0

After patch :

Result: OK: 345285014(c345283891+d1123) nsec, 1000000000
(100byte,1frags)
  2896158pps 2316Mb/sec (2316926400bps) errors: 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

count is incorrectly returned even in case of fail. Return ret instead.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The group of a network device can be queried or changed from userspace
using sysfs.

For example, considering sysfs mounted in /sys, one can change the group
that interface lo belongs to:
	echo 1 > /sys/class/net/lo/group
Signed-off-by: Vlad Dogaru <ddvlad@rosedu.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code is not needed because tb[IFLA_IFNAME] is already
processed in rtnl_newlink(). Remove this redundancy.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduce printk() levels to KERN_INFO in netdev_fix_features() as this will
be used by ethtool and might spam dmesg unnecessarily.

This converts the function to use netdev_info() instead of plain printk().

As a side effect, bonding and bridge devices will now log dropped features
on every slave device change.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.

Occurences found by `grep -r` on net/, drivers/net, include/

[ Move features and vlan_features next to each other in
  struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes the driver get rebuilt every single time you
type 'make' which is beyond rediculious.

I hereby declare this driver to have version "1.0"
Signed-off-by: David S. Miller <davem@davemloft.net>

Add suspend/resume support to tlan driver. This allows not unloading the
driver over suspend/resume.

Also, start (or now, wake) the queue after resetting the adapter --- not the
other way around.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Remove CamelCase.
- Convert hexadecimals to lower case.
- Remove useless comments. Tlan driver contained a name of the function at
  the end of it in a comment. Remove those comments.
- Remove local typedefs. Use real types instead of typedefs in code.
- Resolve space issues and reindent.
- One warning remain, it's a case where printing a single line involves a
  number of printk()s.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow drivers for multiqueue hardware with flow filter tables to
accelerate RFS.  The driver must:

1. Set net_device::rx_cpu_rmap to a cpu_rmap of the RX completion
IRQs (in queue order).  This will provide a mapping from CPUs to the
queues for which completions are handled nearest to them.

2. Implement net_device_ops::ndo_rx_flow_steer.  This operation adds
or replaces a filter steering the given flow to the given RX queue, if
possible.

3. Periodically remove filters for which rps_may_expire_flow() returns
true.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When initiating I/O on a multiqueue and multi-IRQ device, we may want
to select a queue for which the response will be handled on the same
or a nearby CPU.  This requires a reverse-map of IRQ affinity.  Add
library functions to support a generic reverse-mapping from CPUs to
objects with affinity and the specific case where the objects are
IRQs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/sched/sch_hfsc.c
	net/sched/sch_htb.c
	net/sched/sch_tbf.c

Commit 941666c2 "net: RCU conversion of dev_getbyhwaddr() and
arp_ioctl()" introduced a regression, reported by Jamie Heilman.
"arp -Ds 192.168.2.41 eth0 pub" triggered the ASSERT_RTNL() assert
in pneigh_lookup()

Removing RTNL requirement from arp_ioctl() was a mistake, just revert
that part.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a shutdown regression caused by 2a2d31c8 ("intel_idle: open
broadcast clock event").  The clockevent framework can automatically
shutdown broadcast timers for hotremove CPUs.  And we get a shutdown
regression when we shutdown broadcast timer for hot remove CPU, so just
delete some code.

Also fix some section mismatch.
Reported-by: Ari Savolainen <ari.m.savolainen@gmail.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap: DMA: clear interrupt status correctly
  OMAP3: Devkit8000: Fix tps65930 pullup/pulldown configuration
  arm: omap3: cm-t3517: minor comment fix
  arm: omap3: cm-t3517: rtc fix
  omap1: Fix sched_clock implementation when both MPU timer and 32K timer are used
  omap1: Fix booting for 15xx and 730 with omap1_defconfig
  omap1: Fix sched_clock for the MPU timer
  OMAP: PRCM: remove duplicated headers
  OMAP4: clockdomain: bypass unimplemented wake-up dependency functions on OMAP4
  OMAP: counter_32k: init clocksource as part of machine timer init

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf tools: Fix time function double declaration with glibc
  perf tools: Fix build by checking if extra warnings are supported
  perf tools: Fix build when using gcc 3.4.6
  perf tools: Add missing header, fixes build
  perf tools: Fix 64 bit integer format strings
  perf test: Fix build on older glibcs
  perf: perf_event_exit_task_context: s/rcu_dereference/rcu_dereference_raw/
  perf test: Use cpu_map->[cpu] when setting affinity
  perf symbols: Fix annotation of thumb code
  perf: Annotate cpuctx->ctx.mutex to avoid a lockdep splat
  powerpc, perf: Fix frequency calculation for overflowing counters (FSL version)
  perf: Fix perf_event_init_task()/perf_event_free_task() interaction
  perf: Fix find_get_context() vs perf_event_exit_task() race

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  RTC: Remove Kconfig symbol for UIE emulation
  RTC: Properly handle rtc_read_alarm error propagation and fix bug
  RTC: Propagate error handling via rtc_timer_enqueue properly
  acpi_pm: Clear pmtmr_ioport if acpi_pm initialization fails
  rtc: Cleanup removed UIE emulation declaration
  hrtimers: Notify hrtimer users of switches to NOHZ mode

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Fix poor interactivity on UP systems due to group scheduler nice tune bug

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix jump label with RO/NX module protection crash
  x86, hotplug: Fix powersavings with offlined cores on AMD
  x86, mcheck, therm_throt.c: Export symbol platform_thermal_notify to allow coretemp to handler intr
  x86: Use asm-generic/cacheflush.h
  x86: Update CPU cache attributes table descriptors

Michael Witten and Christian Kujau reported that the autogroup
scheduling feature hurts interactivity on their UP systems.

It turns out that this is an older bug in the group scheduling code,
and the wider appeal provided by the autogroup feature exposed it
more prominently.

When on UP with FAIR_GROUP_SCHED enabled, tune shares
only affect tg->shares, but is not reflected in
tg->se->load. The reason is that update_cfs_shares()
does nothing on UP.

So introduce update_cfs_shares() for UP && FAIR_GROUP_SCHED.

This issue was found when enable autogroup scheduling was enabled,
but it is an older bug that also exists on cgroup.cpu on UP.
Reported-and-Tested-by: Michael Witten <mfwitten@gmail.com>
Reported-and-Tested-by: Christian Kujau <christian@nerdbynature.de>
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Mike Galbraith <efault@gmx.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110124073352.GA24186@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

* 'BUG_ON' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  Remove MAYBE_BUILD_BUG_ON
  BUILD_BUG_ON: make it handle more cases

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  module: fix missing semicolons in MODULE macro usage
  param: add null statement to compiled-in module params
  module: fix linker error for MODULE_VERSION when !MODULE and CONFIG_SYSFS=n
  module: show version information for built-in modules in sysfs

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  selinux: return -ENOMEM when memory allocation fails
  tpm: fix panic caused by "tpm: Autodetect itpm devices"
  TPM: Long default timeout fix
  trusted keys: Fix a memory leak in trusted_update().
  keys: add trusted and encrypted maintainers
  encrypted-keys: rename encrypted_defined files to encrypted
  trusted-keys: rename trusted_defined files to trusted

This patch enables support for Intel i340 Quad Port Fiber Adapter.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The semantic patch that makes this output is available
in scripts/coccinelle/api/memdup.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>