Reported-by: Maik-Holger Freudenberg <hhfeuer@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes several problems in the USB_DEVICE table, including missing IDs,
reversed vendor/product codes, and a duplicate ID.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit ebefce3d failed
to set proper PMU value to address ripple issue for AR9485.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CTL power data incorrect in ctlPowerData_2G field of ar9300_eeprom.
Setting incorrect CTL power in calibration is causing lower tx power.
Tx power was reported as 3dBm while operating in channel 6 HT40+/
in channel 11 HT40- due to CTL powers in the calibration is set to
zero.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This causes an databus error on a Broadcom SoC using bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

5000 series has issue supporting power save idle mode:

commit	9dc21533

iwlwifi: always support idle mode for agn devices

For agn devices, always support idle mode which help power
consumption in idle unassociated state.

the above changes cause 5000 become not stable when power management is "on"

http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2312

Cc: stable@kernel.org #2.6.39, #3.0.0
Reported-by: Devin J Pohly <djpohly+iwl@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We may call rt2x00queue_pause_queue(queue) with queue == NULL. Bug
was introduced by commit 62fe7784
"rt2x00: Fix stuck queue in tx failure case" .

Cc: stable@kernel.org # 3.0+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This was introduced by commit
77b5621b (rt2x00: Don't use queue entry
as parameter when creating TX descriptor.)
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This bug has been introduced by:
d5934110
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Mon Jul 11 10:48:51 2011 +0300

    iwlagn: simplify the bus architecture

Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We should clear skb->data not skb itself. Bug was introduced by:
commit 0b8004aa "rt2x00: Properly
reserve room for descriptors in skbs".

Cc: stable@kernel.org # 2.6.36+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This driver uses information from the self member of the pci_bus struct to
get information regarding the bridge to which the PCIe device is attached.
Unfortunately, this member is not established on all architectures, which
leads to a kernel oops.

Skipping the entire block that uses the self member to determine the bridge
vendor will only affect RTL8192DE devices as that driver sets the ASPM support
flag differently when the bridge vendor is Intel. If the self member is
available, there is no functional change.

This patch fixes Bugzilla No. 40212.
Reported-by: Hubert Liao <liao.hubertt@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [back to 2.6.38]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We receive many bug reports about system hang during suspend/resume
when ath9k driver is in use. Adrian Chadd remarked that this problem
happens on systems that have ASPM disabled.

To do not hit the bug, skip doing ->config_pci_powersave magic if PCIe
downstream port device, which ath9k device is connected to, has ASPM
disabled.

Bug was introduced by:

commit 53bc7aa0
Author: Vivek Natarajan <vnatarajan@atheros.com>
Date:   Mon Apr 5 14:48:04 2010 +0530

    ath9k: Add support for newer AR9285 chipsets.

Patch should address:
https://bugzilla.kernel.org/show_bug.cgi?id=37462
https://bugzilla.kernel.org/show_bug.cgi?id=37082
https://bugzilla.redhat.com/show_bug.cgi?id=697157

however I did not receive confirmation about that, except from Camilo
Mesias, whose system stops hang regularly with this patch (but still
hangs from time to time, but this is probably some other bug).
Tested-by: Camilo Mesias <camilo@mesias.co.uk>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The test is off by one so we'd read past the end of the
wiphy->bands[] array on the next line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If settings of tx power was deferred during scan or changing channel we
have to setup them during commit rxon. Fix problem on 3945 (4965 already
has this fix).

Optimize code to apply tx settings only when tx power was actually
changed.

Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With an uninitialized chainmask, the per-channel power will only contain
the power limits for a single chain instead of the combined tx power.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
  tg3: Remove 5719 jumbo frames and TSO blocks
  tg3: Break larger frags into 4k chunks for 5719
  tg3: Add tx BD budgeting code
  tg3: Consolidate code that calls tg3_tx_set_bd()
  tg3: Add partial fragment unmapping code
  tg3: Generalize tg3_skb_error_unmap()
  tg3: Remove short DMA check for 1st fragment
  tg3: Simplify tx bd assignments
  tg3: Reintroduce tg3_tx_ring_info
  ASIX: Use only 11 bits of header for data size
  ASIX: Simplify condition in rx_fixup()
  Fix cdc-phonet build
  bonding: reduce noise during init
  bonding: fix string comparison errors
  net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
  net: add IFF_SKB_TX_SHARED flag to priv_flags
  net: sock_sendmsg_nosec() is static
  forcedeth: fix vlans
  gianfar: fix bug caused by 87c288c6
  gro: Only reset frag0 when skb can be pulled
  ...

* 'for-linus' of git://neil.brown.name/md: (75 commits)
  md/raid10: handle further errors during fix_read_error better.
  md/raid10: Handle read errors during recovery better.
  md/raid10: simplify read error handling during recovery.
  md/raid10: record bad blocks due to write errors during resync/recovery.
  md/raid10:  attempt to fix read errors during resync/check
  md/raid10:  Handle write errors by updating badblock log.
  md/raid10: clear bad-block record when write succeeds.
  md/raid10: avoid writing to known bad blocks on known bad drives.
  md/raid10 record bad blocks as needed during recovery.
  md/raid10: avoid reading known bad blocks during resync/recovery.
  md/raid10 - avoid reading from known bad blocks - part 3
  md/raid10: avoid reading from known bad blocks - part 2
  md/raid10: avoid reading from known bad blocks - part 1
  md/raid10: Split handle_read_error out from raid10d.
  md/raid10: simplify/reindent some loops.
  md/raid5: Clear bad blocks on successful write.
  md/raid5.  Don't write to known bad block on doubtful devices.
  md/raid5: write errors should be recorded as bad blocks if possible.
  md/raid5: use bad-block log to improve handling of uncorrectable read errors.
  md/raid5: avoid reading from known bad blocks.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
  ALSA: hda - Fix duplicated DAC assignments for Realtek
  ALSA: asihpi - off by one in asihpi_hpi_ioctl()
  ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
  ALSA: asihpi - bug fix pa use before init.
  ALSA: hda - Add support for vref-out based mute LED control on IDT codecs

The A0 revision of this chip is the only device that requires these
features to be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 5719 has bug where RDMAs larger than 4k can cause problems.  This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped.  This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch consolidates all code that populates tx BDs into a single
routine.  Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following patches are going to break skb fragments into smaller
sizes.  This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.

The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment.  Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the following patches, unmapping skb fragments will get just as
complicated as mapping them.  This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The first fragment of an skb should always be greater than 8 bytes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated.  To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated.  It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following patches will require the use of an additional flag in the
ring_info structure.  The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AX88772B uses only 11 bits of the header for the actual size. The other bits
are used for something else. This causes dmesg full of messages:

	asix_rx_fixup() Bad Header Length

This patch trims the check to only 11 bits. I believe on older chips, the
remaining 5 top bits are unused.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Try to send to correct address this time!

----------  Forwarded Message  ----------

Subject: [PATCH] Fix cdc-phonet build
Date: Saturday 23 Jul 2011
From: Chris Clayton <chris2553@googlemail.com>
To: linux-net@vger.kernel.org

cdc-phonet does not presently build on linux-3.0 because there is no entry for it in
drivers/net/Makefile. This patch adds that entry.
Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not?  To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>

I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are.  The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...

Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init

Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.

Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.

This was reported and based on work by Takuma Umeya.  I also verified
the problem and tested that this fix resolves it.

V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.

I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.

V3: Actually sending the proper patch....
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Takuma Umeya <tumeya@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs.  There are a handful of drivers that violate this assumption of
course, and need to be fixed up.  This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Karsten Keil <isdn@linux-pingi.de>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Patrick McHardy <kaber@trash.net>
CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pktgen attempts to transmit shared skbs to net devices, which can't be used by
some drivers as they keep state information in skbs.  This patch adds a flag
marking drivers as being able to handle shared skbs in their tx path.  Drivers
are defaulted to being unable to do so, but calling ether_setup enables this
flag, as 90% of the drivers calling ether_setup touch real hardware and can
handle shared skbs.  A subsequent patch will audit drivers to ensure that the
flag is set properly
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Jiri Pirko <jpirko@redhat.com>
CC: Robert Olsson <robert.olsson@its.uu.se>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 87c288c6 "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)

If VLAN insertion is requested (via ethtool) it will be set at an other point ...
Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (54 commits)
  tpm_nsc: Fix bug when loading multiple TPM drivers
  tpm: Move tpm_tis_reenable_interrupts out of CONFIG_PNP block
  tpm: Fix compilation warning when CONFIG_PNP is not defined
  TOMOYO: Update kernel-doc.
  tpm: Fix a typo
  tpm_tis: Probing function for Intel iTPM bug
  tpm_tis: Fix the probing for interrupts
  tpm_tis: Delay ACPI S3 suspend while the TPM is busy
  tpm_tis: Re-enable interrupts upon (S3) resume
  tpm: Fix display of data in pubek sysfs entry
  tpm_tis: Add timeouts sysfs entry
  tpm: Adjust interface timeouts if they are too small
  tpm: Use interface timeouts returned from the TPM
  tpm_tis: Introduce durations sysfs entry
  tpm: Adjust the durations if they are too small
  tpm: Use durations returned from TPM
  TOMOYO: Enable conditional ACL.
  TOMOYO: Allow using argv[]/envp[] of execve() as conditions.
  TOMOYO: Allow using executable's realpath and symlink's target as conditions.
  TOMOYO: Allow using owner/group etc. of file objects as conditions.
  ...

Fix up trivial conflict in security/tomoyo/realpath.c