Current code calls omap4430_phy_init() twice in usb_musb_init().
Calling omap4430_phy_init() once is enough.
This patch removes the first omap4430_phy_init() call, which using an
uninitialized pointer as parameter.

This patch elimates below build warning:
arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init':
arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Bjarne Steinsbo <bsteinsbo@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like 2600 kHz rate does not work reliably on 2430,
so just use the 100 kHz rate.

Otherwise the system often fails to boot properly with:

omap_i2c omap_i2c.2: timeout waiting for bus ready
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
twl: clock init err [-110]
omap_i2c omap_i2c.2: timeout waiting for bus ready
twl: i2c_write failed to transfer all messages
TWL4030 Unable to unlock IDCODE registers --110
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.

Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.

MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: Bryan Buckley <bryan.buckley@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

* 'for-linus' of git://github.com/tiwai/sound:
  ASoC: ssm2602: Re-enable oscillator after suspend
  ALSA: usb-audio: Check for possible chip NULL pointer before clearing probing flag
  ALSA: hda/realtek - Don't detect LO jack when identical with HP
  ALSA: hda/realtek - Avoid bogus HP-pin assignment
  ALSA: HDA: No power nids on 92HD93
  ASoC: omap-mcbsp: Do not attempt to change DAI sysclk if stream is active

* 'pm-fixes' of git://github.com/rjwysocki/linux-pm:
  PM / Clocks: Do not acquire a mutex under a spinlock

That flag no longer makes sense, since we don't look up automount points
as eagerly any more.  Additionally, it turns out that the NO_AUTOMOUNT
handling was buggy to begin with: it would avoid automounting even for
cases where we really *needed* to do the automount handling, and could
return ENOENT for autofs entries that hadn't been instantiated yet.

With our new non-eager automount semantics, one discussion has been
about adding a AT_AUTOMOUNT flag to vfs_fstatat (and thus the
newfstatat() and fstatat64() system calls), but it's probably not worth
it: you can always force at least directory automounting by simply
adding the final '/' to the filename, which works for *all* of the stat
family system calls, old and new.

So AT_NO_AUTOMOUNT (and thus LOOKUP_NO_AUTOMOUNT) really were just a
result of our bad default behavior.
Acked-by: Ian Kent <raven@themaw.net>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently the the internal oscillator is powered down when entering BIAS_OFF
state, but not re-enabled when going back to BIAS_STANDBY. As a result the
CODEC will stop working after suspend if the internal oscillator is used to
generate the sysclock signal. This patch fixes it by clearing the appropriate
bit in the power down register when the CODEC is re-enabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The concensus seems to be that system calls such as stat() etc should
not trigger an automount.  Neither should the l* versions.

This patch therefore adds a LOOKUP_AUTOMOUNT flag to tag those lookups
that _should_ trigger an automount on the last path element.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[ Edited to leave out the cases that are already covered by LOOKUP_OPEN,
  LOOKUP_DIRECTORY and LOOKUP_CREATE - all of which also fundamentally
  force automounting for their own reasons   - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since we've now turned around and made LOOKUP_FOLLOW *not* force an
automount, we want to add the ability to force an automount event on
lookup even if we don't happen to have one of the other flags that force
it implicitly (LOOKUP_OPEN, LOOKUP_DIRECTORY, LOOKUP_PARENT..)

Most cases will never want to use this, since you'd normally want to
delay automounting as long as possible, which usually implies
LOOKUP_OPEN (when we open a file or directory, we really cannot avoid
the automount any more).

But Trond argued sufficiently forcefully that at a minimum bind mounting
a file and quotactl will want to force the automount lookup.  Some other
cases (like nfs_follow_remote_path()) could use it too, although
LOOKUP_DIRECTORY would work there as well.

This commit just adds the flag and logic, no users yet, though.  It also
doesn't actually touch the LOOKUP_NO_AUTOMOUNT flag that is related, and
was made irrelevant by the same change that made us not follow on
LOOKUP_FOLLOW.

Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: David Howells <dhowells@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Greg KH <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'samsung-fixes-3' of git://github.com/kgene/linux-samsung:
  ARM: EXYNOS4: Rename sclk_cam clocks for FIMC driver
  ARM: S5PV210: Rename sclk_cam clocks for FIMC media driver
  ARM: S5P: fix incorrect loop iterator usage on gpio-interrupt
  ARM: S3C2443: Fix bit-reset in setrate of clk_armdiv

The sclk_cam clocks are now controlled by the top level FIMC media
device driver bound to "s5p-fimc-md" platform device.
Rename sclk_cam clocks so they accessible by the corresponding
driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The sclk_cam clocks are now controlled by the top level FIMC media
device driver bound to "s5p-fimc-md" platform device.
Rename sclk_cam clocks so they accessible by the corresponding
driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

* 'hwmon-for-linus' of git://github.com/groeck/linux:
  hwmon: (coretemp) remove struct platform_data * parameter from create_core_data()
  hwmon: (coretemp) constify static data
  hwmon: (coretemp) don't use kernel assigned CPU number as platform device ID
  hwmon: (ds620) Fix handling of negative temperatures
  hwmon: (w83791d) rename prototype parameter from 'register' to 'reg'
  hwmon: (coretemp) Don't use threshold registers for tempX_max
  hwmon: (coretemp) Let the user force TjMax
  hwmon: (coretemp) Drop duplicate function get_pkg_tjmax

* 'kvm-updates/3.1' of git://github.com/avikivity/kvm:
  KVM: x86 emulator: fix Src2CL decode
  KVM: MMU: fix incorrect return of spte

* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
  ARM: 7099/1: futex: preserve oldval in SMP __futex_atomic_op
  ARM: dma-mapping: free allocated page if unable to map
  ARM: fix vmlinux.lds.S discarding sections
  ARM: nommu: fix warning with checksyscalls.sh
  ARM: 7091/1: errata: D-cache line maintenance operation by MVA may not succeed

Commit b7ab83ed (PM: Use spinlock instead of mutex in clock
management functions) introduced a regression causing clocks_mutex
to be acquired under a spinlock.  This happens because
pm_clk_suspend() and pm_clk_resume() call pm_clk_acquire() under
pcd->lock, but pm_clk_acquire() executes clk_get() which causes
clocks_mutex to be acquired.  Similarly, __pm_clk_remove(),
executed under pcd->lock, calls clk_put(), which also causes
clocks_mutex to be acquired.

To fix those problems make pm_clk_add() call pm_clk_acquire(), so
that pm_clk_suspend() and pm_clk_resume() don't have to do that.
Change pm_clk_remove() and pm_clk_destroy() to separate
modifications of the pcd->clock_list list from the actual removal of
PM clock entry objects done by __pm_clk_remove().
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>

Before clearing the probing flag in the error exit path, check that the
chip pointer is not NULL.
Signed-off-by: Thomas Pfaff <tpfaff@gmx.net>
Cc: <stable@kernel.org> [2.6.39+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The spec->autocfg.line_out_pins[] may contain the same pins as hp_pins[]
depending on the configuration.  When they are identical, detecting the
line_jack_present flag screws up the auto-mute because alc_line_automute()
is called unconditionally at initialization while it won't be triggered
by unsol events, thus the old line_jack_present flag is kept for the
whole run.

For fixing this buggy behavior, the driver needs to check whether the
line-outs are really individual, and skip if same as headphone jacks.

Reference: https://bugzilla.novell.com/show_bug.cgi?id=716104Signed-off-by: Takashi Iwai <tiwai@suse.de>

The SMP implementation of __futex_atomic_op clobbers oldval with the
status flag from the exclusive store. This causes it to always read as
zero when performing the FUTEX_OP_CMP_* operation.

This patch updates the ARM __futex_atomic_op implementations to take a
tmp argument, allowing us to store the strex status flag without
overwriting the register containing oldval.

Cc: stable@kernel.org
Reported-by: Minho Ban <mhban@samsung.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When the headphone pin is assigned as primary output to line_out_pins[],
the automatic HP-pin assignment by ASSID must be suppressed.  Otherwise
a wrong pin might be assigned to the headphone and breaks the auto-mute.

Reference: https://bugzilla.novell.com/show_bug.cgi?id=716104Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

If the attempt to map a page for DMA fails (eg, because we're out of
mapping space) then we must not hold on to the page we allocated for
DMA - doing so will result in a memory leak.

Cc: <stable@kernel.org>
Reported-by: Bryan Phillippe <bp@darkforest.org>
Tested-by: Bryan Phillippe <bp@darkforest.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Loop iterator value after terminating list_for_each_entry()
is not NULL. This patch fixes incorrect iterator usage in
GPIO interrupt code for SAMSUNG S5P platforms.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The changed statement should set the old armdiv bits to 0
and not everything else, before setting the new value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

If PTRACE_LISTEN fails after lock_task_sighand() it doesn't drop ->siglock.
Reported-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Src2CL decode (used for double width shifts) erronously decodes only bit 3
of %rcx, instead of bits 7:0.

Fix by decoding %cl in its entirety.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>

__update_clear_spte_slow should return original spte while the
current code returns low half of original spte combined with high
half of new spte.
Signed-off-by: Zhao Jin <cronozhj@gmail.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>

This patch is necessary to make internal speakers work on this chip.

Cc: stable@kernel.org
BugLink: http://bugs.launchpad.net/bugs/854468Tested-by: Alex Wolfson <alex.wolfson@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  spi: Fix WARN when removing spi-fsl-spi module
  spi/imx: Fix spi-imx when the hardware SPI chipselects are used

If CPM mode is not used, the fsl_dummy_rx variable is never allocated.  When
the cleanup attempts to free it, the reference count is zero and a WARN is
generated.  The same CPM mode check used in the initialize is applied to the
free as well.

Tested on 2.6.33 with the previous spi_mpc8xxx driver.  The renamed
spi-fsl-spi driver looks to have the same problem.
Signed-off-by: Jeff Harris <jeff_harris@kentrox.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

sector_t can be different types, so cast it to its largest possible
type.

  drivers/scsi/qla2xxx/qla_isr.c:1509:5: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'sector_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

SCSI_ISCI needs to select SCSI_SAS_HOST_SMP to ensure that all
needed symbols are available to it.

Fixes this build error:

  ERROR: "try_test_sas_gpio_gp_bit" [drivers/scsi/isci/isci.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'perf-tools-for-linus' of git://github.com/acmel/linux:
  perf python: Add missing perf_event__parse_sample 'swapped' parm

* 'perf-tools-for-linus' of git://github.com/acmel/linux:
  perf tools: Add support for disabling -Werror via WERROR=0
  perf top: Fix userspace sample addr map offset
  perf symbols: Fix issue with binaries using 16-bytes buildids (v2)
  perf tool: Fix endianness handling of u32 data in samples
  perf sort: Fix symbol sort output by separating unresolved samples by type
  perf symbols: Synthesize anonymous mmap events
  perf record: Create events initially disabled and enable after init
  perf symbols: Add some heuristics for choosing the best duplicate symbol
  perf symbols: Preserve symbol scope when parsing /proc/kallsyms
  perf symbols: /proc/kallsyms does not sort module symbols
  perf symbols: Fix ppc64 SEGV in dso__load_sym with debuginfo files
  perf probe: Fix regression of variable finder

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix DDIA enable on some rs690 systems
  Revert "drm/radeon/kms: fix typo in r100_blit_copy"

* 'for-linus' of git://github.com/tiwai/sound:
  ALSA: usb-audio - clear chip->probing on error exit
  ALSA: fm801: Gracefully handle failure of tuner auto-detect
  ALSA: fm801: Fix double free in case of error in tuner detection
  ASoC: Ensure we generate a driver name
  ASoC: Remove bitrotted wm8962_resume()
  ASoC: bf5xx-ad73311: Fix prototype for bf5xx_probe

Problem introduced in 936be503, that missed one perf_event__parse_sample
user, the python binding.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-ja4phms9618ggi657plyuch2@git.kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

The only caller of the function obtained the pointer solely for the
purpose of passing it to this function, while it can be easily
determined from the struct platform_device * parameter also passed.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

These arrays won't ever be written to, so protect them from
unintentional modification.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>