And delete rt6_redirect(), since it is no longer used.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Hook it into dst_ops->redirect as well.
Signed-off-by: David S. Miller <davem@davemloft.net>

This sets things up so that we can have the protocol error handlers
call down into the ipv6 route code for redirects just as ipv4 already
does.
Signed-off-by: David S. Miller <davem@davemloft.net>

This is going to be used internally by the rt6 redirect code.
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer needed, as the protocol handlers now all properly
propagate the redirect back into the routing code.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

All of the redirect acceptance policy is now contained within.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass in the SKB rather than just the IP addresses, so that policy
and other aspects can reside in ip_rt_redirect() rather then
icmp_redirect().
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

And thus, we can remove the ping_err() hack.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

This introduce TSQ (TCP Small Queues)

TSQ goal is to reduce number of TCP packets in xmit queues (qdisc &
device queues), to reduce RTT and cwnd bias, part of the bufferbloat
problem.

sk->sk_wmem_alloc not allowed to grow above a given limit,
allowing no more than ~128KB [1] per tcp socket in qdisc/dev layers at a
given time.

TSO packets are sized/capped to half the limit, so that we have two
TSO packets in flight, allowing better bandwidth use.

As a side effect, setting the limit to 40000 automatically reduces the
standard gso max limit (65536) to 40000/2 : It can help to reduce
latencies of high prio packets, having smaller TSO packets.

This means we divert sock_wfree() to a tcp_wfree() handler, to
queue/send following frames when skb_orphan() [2] is called for the
already queued skbs.

Results on my dev machines (tg3/ixgbe nics) are really impressive,
using standard pfifo_fast, and with or without TSO/GSO.

Without reduction of nominal bandwidth, we have reduction of buffering
per bulk sender :
< 1ms on Gbit (instead of 50ms with TSO)
< 8ms on 100Mbit (instead of 132 ms)

I no longer have 4 MBytes backlogged in qdisc by a single netperf
session, and both side socket autotuning no longer use 4 Mbytes.

As skb destructor cannot restart xmit itself ( as qdisc lock might be
taken at this point ), we delegate the work to a tasklet. We use one
tasklest per cpu for performance reasons.

If tasklet finds a socket owned by the user, it sets TSQ_OWNED flag.
This flag is tested in a new protocol method called from release_sock(),
to eventually send new segments.

[1] New /proc/sys/net/ipv4/tcp_limit_output_bytes tunable
[2] skb_orphan() is usually called at TX completion time,
  but some drivers call it in their start_xmit() handler.
  These drivers should at least use BQL, or else a single TCP
  session can still fill the whole NIC TX ring, since TSQ will
  have no effect.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recent patch "tcp: Maintain dynamic metrics in local cache." introduced
an out of bounds access due to what appears to be a typo.   I believe this
change should resolve the issue by replacing the access to RTAX_CWND with
TCP_METRIC_CWND.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes build when ipv6 is disabled.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mld->mld_maxdelay is net endian, so we should use ntohs, not htons

CC: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 6d29b1ef introduces a bug, ntohs is __be16_to_cpu,
not cpu_to_be16.

We always use htons on IP_OFFSET and IP_MF, then compare
with network package.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, Using htons on skb->protocol is wrong.

And fix two code style issues: indentation and remove
unnecessary parentheses.

CC: Tristram Ha <Tristram.Ha@micrel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Joe Perches <joe@perches.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/batman-adv/bridge_loop_avoidance.c
	net/batman-adv/bridge_loop_avoidance.h
	net/batman-adv/soft-interface.c
	net/mac80211/mlme.c

With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).

The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>

In rare cases, bnx2x_free_tx_skbs() can unmap the wrong DMA address
when it gets to the last entry of the tx ring.  We were not using
the proper macro to skip the last entry when advancing the tx index.
Reported-by: Zongyun Lai <zlai@vmware.com>
Reviewed-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz reported triggering of WARN_ON_ONCE(delta < len); in
skb_try_coalesce()
This warning tracks drivers that incorrectly set skb->truesize

IPoIB indeed allocates a full page to store a fragment, but only
accounts in skb->truesize the used part of the page (frame length)

This patch fixes skb truesize underestimation, and
also fixes a performance issue, because RX skbs have not enough tailroom
to allow IP and TCP stacks to pull their header in skb linear part
without an expensive call to pskb_expand_head()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Shlomo Pongartz <shlomop@mellanox.com>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In driver reload test there is a memory leak.
The structure vlan_info was not freed when the driver was removed.
It was not released since the nr_vids var is one after last vlan was removed.
The nr_vids is one, since vlan zero is added to the interface when the interface
is being set, but the vlan zero is not deleted at unregister.
Fix - delete vlan zero when we unregister the device.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes:
- fix a bug generated by the wrong interaction between the GW feature and the
  Bridge Loop Avoidance

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Missing case was causing ethtool self test to print garbage
value in extra info section.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TX queue was being stopped at beginning of send path instead
of at the end when last descriptor is used.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enabling RX cut-thru mode yields better performance as received frames
start getting written to memory before a whole frame is received.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increase the number of outstanding read and write AXI transactions from 1
to 8 for better performance.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix intermittent hangs in xgmac_rx_refill. If a ring buffer entry already
had an skb allocated, then xgmac_rx_refill would get stuck in a loop. This
can happen on a rx error when we just leave the skb allocated to the entry.

[ 7884.510000] INFO: rcu_preempt detected stall on CPU 0 (t=727315 jiffies)
[ 7884.510000] [<c0010a59>] (unwind_backtrace+0x1/0x98) from [<c006fd93>] (__rcu_pending+0x11b/0x2c4)
[ 7884.510000] [<c006fd93>] (__rcu_pending+0x11b/0x2c4) from [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8)
[ 7884.510000] [<c0070b95>] (rcu_check_callbacks+0xed/0x1a8) from [<c0036abb>] (update_process_times+0x2b/0x48)
[ 7884.510000] [<c0036abb>] (update_process_times+0x2b/0x48) from [<c004e8fd>] (tick_sched_timer+0x51/0x94)
[ 7884.510000] [<c004e8fd>] (tick_sched_timer+0x51/0x94) from [<c0045527>] (__run_hrtimer+0x4f/0x1e8)
[ 7884.510000] [<c0045527>] (__run_hrtimer+0x4f/0x1e8) from [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4)
[ 7884.510000] [<c0046003>] (hrtimer_interrupt+0xd7/0x1e4) from [<c00101d3>] (twd_handler+0x17/0x24)
[ 7884.510000] [<c00101d3>] (twd_handler+0x17/0x24) from [<c006be39>] (handle_percpu_devid_irq+0x59/0x114)
[ 7884.510000] [<c006be39>] (handle_percpu_devid_irq+0x59/0x114) from [<c0069aab>] (generic_handle_irq+0x17/0x2c)
[ 7884.510000] [<c0069aab>] (generic_handle_irq+0x17/0x2c) from [<c000cc8d>] (handle_IRQ+0x35/0x7c)
[ 7884.510000] [<c000cc8d>] (handle_IRQ+0x35/0x7c) from [<c033b153>] (__irq_svc+0x33/0xb8)
[ 7884.510000] [<c033b153>] (__irq_svc+0x33/0xb8) from [<c0244b06>] (xgmac_rx_refill+0x3a/0x140)
[ 7884.510000] [<c0244b06>] (xgmac_rx_refill+0x3a/0x140) from [<c02458ed>] (xgmac_poll+0x265/0x3bc)
[ 7884.510000] [<c02458ed>] (xgmac_poll+0x265/0x3bc) from [<c029fcbf>] (net_rx_action+0xc3/0x200)
[ 7884.510000] [<c029fcbf>] (net_rx_action+0xc3/0x200) from [<c0030cab>] (__do_softirq+0xa3/0x1bc)
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix net tx watchdog timeout recovery. The descriptor ring was reset,
but the DMA engine was not reset to the beginning of the ring.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->dev is being unnecessarily set by the driver on packet recieve.
eth_type_trans already sets skb->dev to the proper value and it is not
referenced anywhere else in the dirver, thus making its setting unnecessary.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>