The SDHCI controller on Tegra186 supports 40-bit addressing, which is
usually enough to address all of system memory. However, if the SDHCI
controller is behind an IOMMU, the address space can go beyond. This
happens on Tegra186 and later where the ARM SMMU has an input address
space of 48 bits. If the DMA API is backed by this ARM SMMU, the top-
down IOVA allocator will cause IOV addresses to be returned that the
SDHCI controller cannot access.

Unfortunately, prior to the introduction of the ->set_dma_mask() host
operation, the SDHCI core would set either a 64-bit DMA mask if the
controller claimed to support 64-bit addressing, or a 32-bit DMA mask
otherwise.

Since the full 64 bits cannot be addressed on Tegra, this had to be
worked around in commit 68481a7e ("mmc: tegra: Mark 64 bit dma
broken on Tegra186") by setting the SDHCI_QUIRK2_BROKEN_64_BIT_DMA
quirk, which effectively restricts the DMA mask to 32 bits.

One disadvantage of this is that dma_map_*() APIs will now try to use
the swiotlb to bounce DMA to addresses beyond of the controller's DMA
mask. This in turn caused degraded performance and can lead to
situations where the swiotlb buffer is exhausted, which in turn leads
to DMA transfers to fail.

With the recent introduction of the ->set_dma_mask() host operation,
this can now be properly fixed. For each generation of Tegra, the exact
supported DMA mask can be configured. This kills two birds with one
stone: it avoids the use of bounce buffers because system memory never
exceeds the addressable memory range of the SDHCI controllers on these
devices, and at the same time when an IOMMU is involved, it prevents
IOV addresses from being allocated beyond the addressible range of the
controllers.

Since the DMA mask is now properly handled, the 64-bit DMA quirk can be
removed.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[treding@nvidia.com: provide more background in commit message]
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.15 +
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add host operation ->set_dma_mask() so that drivers can define their own
DMA masks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.15 +
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We must not unconditionally set the DMA snoop bit; if the DMA API is
assuming that the device is not DMA coherent, and the device snoops the
CPU caches, the device can see stale cache lines brought in by
speculative prefetch.

This leads to the device seeing stale data, potentially resulting in
corrupted data transfers.  Commonly, this results in a descriptor fetch
error such as:

mmc0: ADMA error
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr:  0x00000000 | Version:  0x00002202
mmc0: sdhci: Blk size:  0x00000008 | Blk cnt:  0x00000001
mmc0: sdhci: Argument:  0x00000000 | Trn mode: 0x00000013
mmc0: sdhci: Present:   0x01f50008 | Host ctl: 0x00000038
mmc0: sdhci: Power:     0x00000003 | Blk gap:  0x00000000
mmc0: sdhci: Wake-up:   0x00000000 | Clock:    0x000040d8
mmc0: sdhci: Timeout:   0x00000003 | Int stat: 0x00000001
mmc0: sdhci: Int enab:  0x037f108f | Sig enab: 0x037f108b
mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00002202
mmc0: sdhci: Caps:      0x35fa0000 | Caps_1:   0x0000af00
mmc0: sdhci: Cmd:       0x0000333a | Max curr: 0x00000000
mmc0: sdhci: Resp[0]:   0x00000920 | Resp[1]:  0x001d8a33
mmc0: sdhci: Resp[2]:   0x325b5900 | Resp[3]:  0x3f400e00
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ADMA Err:  0x00000009 | ADMA Ptr: 0x000000236d43820c
mmc0: sdhci: ============================================
mmc0: error -5 whilst initialising SD card

but can lead to other errors, and potentially direct the SDHCI
controller to read/write data to other memory locations (e.g. if a valid
descriptor is visible to the device in a stale cache line.)

Fix this by ensuring that the DMA snoop bit corresponds with the
behaviour of the DMA API.  Since the driver currently only supports DT,
use of_dma_is_coherent().  Note that device_get_dma_attr() can not be
used as that risks re-introducing this bug if/when the driver is
converted to ACPI.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

ADMA errors are potentially data corrupting events; although we print
the register state, we do not usefully print the ADMA descriptors.
Worse than that, we print them by referencing their virtual address
which is meaningless when the register state gives us the DMA address
of the failing descriptor.

Print the ADMA descriptors giving their DMA addresses rather than their
virtual addresses, and print them using SDHCI_DUMP() rather than DBG().

We also do not show the correct value of the interrupt status register;
the register dump shows the current value, after we have cleared the
pending interrupts we are going to service.  What is more useful is to
print the interrupts that _were_ pending at the time the ADMA error was
encountered.  Fix that too.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull crypto fixes froim Herbert Xu:
 "This fixes the following issues:

   - potential boot hang in hwrng

   - missing switch/break in talitos

   - bugs and warnings in hisilicon

   - build warning in inside-secure"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: hisilicon - avoid unused function warning
  hwrng: core - don't wait on add_early_randomness()
  crypto: hisilicon - Fix return value check in hisi_zip_acompress()
  crypto: hisilicon - Matching the dma address for dma_pool_free()
  crypto: hisilicon - Fix double free in sec_free_hw_sgl()
  crypto: inside-secure - Fix unused variable warning when CONFIG_PCI=n
  crypto: talitos - fix missing break in switch statement

Pull power supply and reset updates from Sebastian Reichel:
 "Core:
   - Ensure HWMON devices are registered with valid names
   - Fix device wakeup code

  Drivers:
   - bq25890_charger: Add BQ25895 support
   - axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
   - sc27xx: improve battery calibration
   - misc small fixes all over drivers"

* tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
  power: supply: cpcap-charger: Enable vbus boost voltage
  power: supply: sc27xx: Add POWER_SUPPLY_PROP_CALIBRATE attribute
  power: supply: sc27xx: Optimize the battery capacity calibration
  power: supply: sc27xx: Make sure the alarm capacity is larger than 0
  power: supply: sc27xx: Fix the the accuracy issue of coulomb calculation
  power: supply: sc27xx: Fix conditon to enable the FGU interrupt
  power: supply: sc27xx: Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute
  power: supply: max77650: add MODULE_ALIAS()
  power: supply: isp1704: remove redundant assignment to variable ret
  power: supply: bq25890_charger: Add the BQ25895 part
  power: supply: sc27xx: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
  power: supply: sc27xx: Introduce local variable 'struct device *dev'
  power: reset: reboot-mode: Fix author email format
  power: supply: ab8500: remove set but not used variables 'vbup33_vrtcn' and 'bup_vch_range'
  power: supply: max17042_battery: Fix a typo in function names
  power: reset: gpio-restart: Fix typo when gpio reset is not found
  power: supply: Init device wakeup after device_add()
  power: supply: ab8500_charger: Mark expected switch fall-through
  power: supply: sbs-battery: only return health when battery present
  MAINTAINERS: N900: Remove isp1704_charger.h record
  ...

Pull HSI updates from Sebastian Reichel:
 "Misc cleanups"

* tag 'hsi-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
  HSI: Remove dev_err() usage after platform_get_irq()
  HSI: ssi_protocol: Mark expected switch fall-throughs

Commit feb4eb06 ("firmware: bcm47xx_nvram: Correct size_t printf
format") was wrong, and changed a printout of 'header.len' - which is an
u32 type - to use '%zu'.

It apparently did pattern matching on the other case, where it printed
out 'nvram_len', which is indeed of type 'size_t'.

Rather than undoing the change, this just makes it use the variable that
the change seemed to expect to be used.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It's an unusual configuration, and was apparently never tested, and not
caught in linux-next because of a combination of travels and it making
it into the tree too late.

The fix is to simply move the #define to outside the CONFIG_MODULE
section, since MODULE_INFO() will do the right thing.

Cc: Martijn Coenen <maco@android.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthias Maennich <maennich@google.com>
Cc: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull RTC updates from Alexandre Belloni:
 "Two new drivers and the new pcf2127 feature make the bulk of the
  additions. The rest are the usual fixes and new features.

  Subsystem:
   - add debug message when registration fails

  New drivers:
   - Amlogic Virtual Wake
   - Freescale FlexTimer Module alarm

  Drivers:
   - remove superfluous error messages
   - convert to i2c_new_dummy_device and devm_i2c_new_dummy_device
   - Remove dev_err() usage after platform_get_irq()
   - Set RTC range for: pcf2123, pcf8563, snvs.
   - pcf2127: tamper detection and watchdog support
   - pcf85363: fix regmap issue
   - sun6i: H6 support
   - remove w90x900/nuc900 driver"

* tag 'rtc-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (51 commits)
  rtc: meson: mark PM functions as __maybe_unused
  rtc: sc27xx: Remove clearing SPRD_RTC_POWEROFF_ALM_FLAG flag
  dt-bindings: rtc: ds1307: add rx8130 compatible
  rtc: sun6i: Allow using as wakeup source from suspend
  rtc: pcf8563: let the core handle range offsetting
  rtc: pcf8563: remove useless indirection
  rtc: pcf8563: convert to devm_rtc_allocate_device
  rtc: pcf8563: add Microcrystal RV8564 compatible
  rtc: pcf8563: add Epson RTC8564 compatible
  rtc: s35390a: convert to devm_i2c_new_dummy_device()
  rtc: max77686: convert to devm_i2c_new_dummy_device()
  rtc: pcf85363/pcf85263: fix regmap error in set_time
  rtc: snvs: switch to rtc_time64_to_tm/rtc_tm_to_time64
  rtc: snvs: set range
  rtc: snvs: fix possible race condition
  rtc: pcf2127: bugfix: watchdog build dependency
  rtc: pcf2127: add tamper detection support
  rtc: pcf2127: add watchdog feature support
  rtc: pcf2127: bugfix: read rtc disables watchdog
  rtc: pcf2127: cleanup register and bit defines
  ...

Pull rpmsg updates from Bjorn Andersson:
 "This contains updates to make the rpmsg sample driver more useful,
  fixes the naming of GLINK devices to avoid naming collisions and a few
  minor bug fixes. It also updates MAINTAINERS to reflect the move to
  kernel.org"

* tag 'rpmsg-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
  rpmsg: glink-smem: Name the edge based on parent remoteproc
  rpmsg: glink: Use struct_size() helper
  rpmsg: virtio_rpmsg_bus: replace "%p" with "%pK"
  MAINTAINERS: rpmsg: fix git tree location
  rpmsg: core: fix comments
  samples/rpmsg: Introduce a module parameter for message count
  samples/rpmsg: Replace print_hex_dump() with print_hex_dump_debug()

Pull remoteproc updates from Bjorn Andersson:
 "This exposes the remoteproc's name in sysfs, allows stm32 to enter
  platform standby and provides bug fixes for stm32 and Qualcomm's modem
  remoteproc drivers. Finally it updates MAINTAINERS to reflect the move
  to kernel.org"

* tag 'rproc-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
  MAINTAINERS: remoteproc: update git tree location
  remoteproc: Remove dev_err() usage after platform_get_irq()
  remoteproc: stm32: manage the get_irq probe defer case
  remoteproc: stm32: clear MCU PDDS at firmware start
  remoteproc: qcom: q6v5-mss: fixup q6v5_pds_enable error handling
  remoteproc: Add a sysfs interface for name
  remoteproc: qcom: Move glink_ssr notification after stop

Pull soundwire updates from Vinod Koul:
 "This includes DT support thanks to Srini and more work done by Intel
  (Pierre) on improving cadence and intel support.

  Summary:

   - Add DT bindings and DT support in core

   - Add debugfs support for soundwire properties

   - Improvements on streaming handling to core

   - Improved handling of Cadence module

   - More updates and improvements to Intel driver"

* tag 'soundwire-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (30 commits)
  soundwire: stream: make stream name a const pointer
  soundwire: Add compute_params callback
  soundwire: core: add device tree support for slave devices
  dt-bindings: soundwire: add slave bindings
  soundwire: bus: set initial value to port_status
  soundwire: intel: handle disabled links
  soundwire: intel: add debugfs register dump
  soundwire: cadence_master: add debugfs register dump
  soundwire: add debugfs support
  soundwire: intel: remove unused variables
  soundwire: intel: move shutdown() callback and don't export symbol
  soundwire: cadence_master: add kernel parameter to override interrupt mask
  soundwire: intel_init: add kernel module parameter to filter out links
  soundwire: cadence_master: fix divider setting in clock register
  soundwire: cadence_master: make use of mclk_freq property
  soundwire: intel: read mclk_freq property from firmware
  soundwire: add new mclk_freq field for properties
  soundwire: stream: remove unnecessary variable initializations
  soundwire: stream: fix disable sequence
  soundwire: include mod_devicetable.h to avoid compiling warnings
  ...

Pull modules updates from Jessica Yu:
 "The main bulk of this pull request introduces a new exported symbol
  namespaces feature. The number of exported symbols is increasingly
  growing with each release (we're at about 31k exports as of 5.3-rc7)
  and we currently have no way of visualizing how these symbols are
  "clustered" or making sense of this huge export surface.

  Namespacing exported symbols allows kernel developers to more
  explicitly partition and categorize exported symbols, as well as more
  easily limiting the availability of namespaced symbols to other parts
  of the kernel. For starters, we have introduced the USB_STORAGE
  namespace to demonstrate the API's usage. I have briefly summarized
  the feature and its main motivations in the tag below.

  Summary:

   - Introduce exported symbol namespaces.

     This new feature allows subsystem maintainers to partition and
     categorize their exported symbols into explicit namespaces. Module
     authors are now required to import the namespaces they need.

     Some of the main motivations of this feature include: allowing
     kernel developers to better manage the export surface, allow
     subsystem maintainers to explicitly state that usage of some
     exported symbols should only be limited to certain users (think:
     inter-module or inter-driver symbols, debugging symbols, etc), as
     well as more easily limiting the availability of namespaced symbols
     to other parts of the kernel.

     With the module import requirement, it is also easier to spot the
     misuse of exported symbols during patch review.

     Two new macros are introduced: EXPORT_SYMBOL_NS() and
     EXPORT_SYMBOL_NS_GPL(). The API is thoroughly documented in
     Documentation/kbuild/namespaces.rst.

   - Some small code and kbuild cleanups here and there"

* tag 'modules-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
  module: Remove leftover '#undef' from export header
  module: remove unneeded casts in cmp_name()
  module: move CONFIG_UNUSED_SYMBOLS to the sub-menu of MODULES
  module: remove redundant 'depends on MODULES'
  module: Fix link failure due to invalid relocation on namespace offset
  usb-storage: export symbols in USB_STORAGE namespace
  usb-storage: remove single-use define for debugging
  docs: Add documentation for Symbol Namespaces
  scripts: Coccinelle script for namespace dependencies.
  modpost: add support for generating namespace dependencies
  export: allow definition default namespaces in Makefiles or sources
  module: add config option MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS
  modpost: add support for symbol namespaces
  module: add support for symbol namespaces.
  export: explicitly align struct kernel_symbol
  module: support reading multiple values per modinfo tag

Pull ARM updates from Russell King:

 - fix various clang build and cppcheck issues

 - switch ARM to use new common outgoing-CPU-notification code

 - add some additional explanation about the boot code

 - kbuild "make clean" fixes

 - get rid of another "(____ptrval____)", this time for the VDSO code

 - avoid treating cache maintenance faults as a write

 - add a frame pointer unwinder implementation for clang

 - add EDAC support for Aurora L2 cache

 - improve robustness of adjust_lowmem_bounds() finding the bounds of
   lowmem.

 - add reset control for AMBA primecell devices

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (24 commits)
  ARM: 8906/1: drivers/amba: add reset control to amba bus probe
  ARM: 8905/1: Emit __gnu_mcount_nc when using Clang 10.0.0 or newer
  ARM: 8904/1: skip nomap memblocks while finding the lowmem/highmem boundary
  ARM: 8903/1: ensure that usable memory in bank 0 starts from a PMD-aligned address
  ARM: 8891/1: EDAC: armada_xp: Add support for more SoCs
  ARM: 8888/1: EDAC: Add driver for the Marvell Armada XP SDRAM and L2 cache ECC
  ARM: 8892/1: EDAC: Add missing debugfs_create_x32 wrapper
  ARM: 8890/1: l2x0: add marvell,ecc-enable property for aurora
  ARM: 8889/1: dt-bindings: document marvell,ecc-enable binding
  ARM: 8886/1: l2x0: support parity-enable/disable on aurora
  ARM: 8885/1: aurora-l2: add defines for parity and ECC registers
  ARM: 8887/1: aurora-l2: add prefix to MAX_RANGE_SIZE
  ARM: 8902/1: l2c: move cache-aurora-l2.h to asm/hardware
  ARM: 8900/1: UNWINDER_FRAME_POINTER implementation for Clang
  ARM: 8898/1: mm: Don't treat faults reported from cache maintenance as writes
  ARM: 8896/1: VDSO: Don't leak kernel addresses
  ARM: 8895/1: visit mach-* and plat-* directories when cleaning
  ARM: 8894/1: boot: Replace open-coded nop with macro
  ARM: 8893/1: boot: Explain the 8 nops
  ARM: 8876/1: fix O= building with CONFIG_FPE_FASTFPE
  ...

Pull MIPS updates from Paul Burton:
 "Main MIPS changes:

   - boot_mem_map is removed, providing a nice cleanup made possible by
     the recent removal of bootmem.

   - Some fixes to atomics, in general providing compiler barriers for
     smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
     or MIPS32 systems using cmpxchg64().

   - Conversion to the new generic VDSO infrastructure courtesy of
     Vincenzo Frascino.

   - Removal of undefined behavior in set_io_port_base(), fixing the
     behavior of some MIPS kernel configurations when built with recent
     clang versions.

   - Initial MIPS32 huge page support, functional on at least Ingenic
     SoCs.

   - pte_special() is now supported for some configurations, allowing
     among other things generic fast GUP to be used.

   - Miscellaneous fixes & cleanups.

  And platform specific changes:

   - Major improvements to Ingenic SoC support from Paul Cercueil,
     mostly enabled by the inclusion of the new TCU (timer-counter unit)
     drivers he's spent a very patient year or so working on. Plus some
     fixes for X1000 SoCs from Zhou Yanjie.

   - Netgear R6200 v1 systems are now supported by the bcm47xx platform.

   - DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"

* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
  MIPS: Detect bad _PFN_SHIFT values
  MIPS: Disable pte_special() for MIPS32 with RiXi
  MIPS: ralink: deactivate PCI support for SOC_MT7621
  mips: compat: vdso: Use legacy syscalls as fallback
  MIPS: Drop Loongson _CACHE_* definitions
  MIPS: tlbex: Remove cpu_has_local_ebase
  MIPS: tlbex: Simplify r3k check
  MIPS: Select R3k-style TLB in Kconfig
  MIPS: PCI: refactor ioc3 special handling
  mips: remove ioremap_cachable
  mips/atomic: Fix smp_mb__{before,after}_atomic()
  mips/atomic: Fix loongson_llsc_mb() wreckage
  mips/atomic: Fix cmpxchg64 barriers
  MIPS: Octeon: remove duplicated include from dma-octeon.c
  firmware: bcm47xx_nvram: Allow COMPILE_TEST
  firmware: bcm47xx_nvram: Correct size_t printf format
  MIPS: Treat Loongson Extensions as ASEs
  MIPS: Remove dev_err() usage after platform_get_irq()
  MIPS: dts: mscc: describe the PTP ready interrupt
  MIPS: dts: mscc: describe the PTP register range
  ...

Pull gfs2 updates from Andreas Gruenbacher:

 - Use asynchronous glocks and timeouts to recover from deadlocks during
   rename and exchange: the lock ordering constraints the vfs uses are
   not sufficient to prevent deadlocks across multiple nodes.

 - Add support for IOMAP_ZERO and use iomap_zero_range to replace gfs2
   specific code.

 - Various other minor fixes and cleanups.

* tag 'gfs2-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: clear buf_in_tr when ending a transaction in sweep_bh_for_rgrps
  gfs2: Improve mmap write vs. truncate consistency
  gfs2: Use async glocks for rename
  gfs2: create function gfs2_glock_update_hold_time
  gfs2: separate holder for rgrps in gfs2_rename
  gfs2: Delete an unnecessary check before brelse()
  gfs2: Minor PAGE_SIZE arithmetic cleanups
  gfs2: Fix recovery slot bumping
  gfs2: Fix possible fs name overflows
  gfs2: untangle the logic in gfs2_drevalidate
  gfs2: Always mark inode dirty in fallocate
  gfs2: Minor gfs2_alloc_inode cleanup
  gfs2: implement gfs2_block_zero_range using iomap_zero_range
  gfs2: Add support for IOMAP_ZERO
  gfs2: gfs2_iomap_begin cleanup

Pull f2fs updates from Jaegeuk Kim:
 "In this round, we introduced casefolding support in f2fs, and fixed
  various bugs in individual features such as IO alignment,
  checkpoint=disable, quota, and swapfile.

  Enhancement:
   - support casefolding w/ enhancement in ext4
   - support fiemap for directory
   - support FS_IO_GET|SET_FSLABEL

  Bug fix:
   - fix IO stuck during checkpoint=disable
   - avoid infinite GC loop
   - fix panic/overflow related to IO alignment feature
   - fix livelock in swap file
   - fix discard command leak
   - disallow dio for atomic_write"

* tag 'f2fs-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (51 commits)
  f2fs: add a condition to detect overflow in f2fs_ioc_gc_range()
  f2fs: fix to add missing F2FS_IO_ALIGNED() condition
  f2fs: fix to fallback to buffered IO in IO aligned mode
  f2fs: fix to handle error path correctly in f2fs_map_blocks
  f2fs: fix extent corrupotion during directIO in LFS mode
  f2fs: check all the data segments against all node ones
  f2fs: Add a small clarification to CONFIG_FS_F2FS_FS_SECURITY
  f2fs: fix inode rwsem regression
  f2fs: fix to avoid accessing uninitialized field of inode page in is_alive()
  f2fs: avoid infinite GC loop due to stale atomic files
  f2fs: Fix indefinite loop in f2fs_gc()
  f2fs: convert inline_data in prior to i_size_write
  f2fs: fix error path of f2fs_convert_inline_page()
  f2fs: add missing documents of reserve_root/resuid/resgid
  f2fs: fix flushing node pages when checkpoint is disabled
  f2fs: enhance f2fs_is_checkpoint_ready()'s readability
  f2fs: clean up __bio_alloc()'s parameter
  f2fs: fix wrong error injection path in inc_valid_block_count()
  f2fs: fix to writeout dirty inode during node flush
  f2fs: optimize case-insensitive lookups
  ...

Pull ext2, quota, udf fixes and cleanups from Jan Kara:

 - two small quota fixes (in grace time handling and possible missed
   accounting of preallocated blocks beyond EOF).

 - some ext2 cleanups

 - udf fixes for better compatibility with Windows 10 generated media
   (named streams, write-protection using domain-identifier, placement
   of volume recognition sequence)

 - some udf cleanups

* tag 'for_v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  quota: fix wrong condition in is_quota_modification()
  fs-udf: Delete an unnecessary check before brelse()
  ext2: Delete an unnecessary check before brelse()
  udf: Drop forward function declarations
  udf: Verify domain identifier fields
  udf: augment UDF permissions on new inodes
  udf: Use dynamic debug infrastructure
  udf: reduce leakage of blocks related to named streams
  udf: prevent allocation beyond UDF partition
  quota: fix condition for resetting time limit in do_set_dqblk()
  ext2: code cleanup for ext2_free_blocks()
  ext2: fix block range in ext2_data_block_valid()
  udf: support 2048-byte spacing of VRS descriptors on 4K media
  udf: refactor VRS descriptor identification

Pull ext4 updates from Ted Ts'o:
 "Added new ext4 debugging ioctls to allow userspace to get information
  about the state of the extent status cache.

  Dropped workaround for pre-1970 dates which were encoded incorrectly
  in pre-4.4 kernels. Since both the kernel correctly generates, and
  e2fsck detects and fixes this issue for the past four years, it'e time
  to drop the workaround. (Also, it's not like files with dates in the
  distant past were all that common in the first place.)

  A lot of miscellaneous bug fixes and cleanups, including some ext4
  Documentation fixes. Also included are two minor bug fixes in
  fs/unicode"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (21 commits)
  unicode: make array 'token' static const, makes object smaller
  unicode: Move static keyword to the front of declarations
  ext4: add missing bigalloc documentation.
  ext4: fix kernel oops caused by spurious casefold flag
  ext4: fix integer overflow when calculating commit interval
  ext4: use percpu_counters for extent_status cache hits/misses
  ext4: fix potential use after free after remounting with noblock_validity
  jbd2: add missing tracepoint for reserved handle
  ext4: fix punch hole for inline_data file systems
  ext4: rework reserved cluster accounting when invalidating pages
  ext4: documentation fixes
  ext4: treat buffers with write errors as containing valid data
  ext4: fix warning inside ext4_convert_unwritten_extents_endio
  ext4: set error return correctly when ext4_htree_store_dirent fails
  ext4: drop legacy pre-1970 encoding workaround
  ext4: add new ioctl EXT4_IOC_GET_ES_CACHE
  ext4: add a new ioctl EXT4_IOC_GETSTATE
  ext4: add a new ioctl EXT4_IOC_CLEAR_ES_CACHE
  jbd2: flush_descriptor(): Do not decrease buffer head's ref count
  ext4: remove unnecessary error check
  ...

Pull UBI, UBIFS and JFFS2 updates from Richard Weinberger:
 "UBI:
   - Be less stupid when placing a fastmap anchor
   - Try harder to get an empty PEB in case of contention
   - Make ubiblock to warn if image is not a multiple of 512

  UBIFS:
   - Various fixes in error paths

  JFFS2:
   - Various fixes in error paths"

* tag 'upstream-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  jffs2: Fix memory leak in jffs2_scan_eraseblock() error path
  jffs2: Remove jffs2_gc_fetch_page and jffs2_gc_release_page
  jffs2: Fix possible null-pointer dereferences in jffs2_add_frag_to_fragtree()
  ubi: block: Warn if volume size is not multiple of 512
  ubifs: Fix memory leak bug in alloc_ubifs_info() error path
  ubifs: Fix memory leak in __ubifs_node_verify_hmac error path
  ubifs: Fix memory leak in read_znode() error path
  ubi: ubi_wl_get_peb: Increase the number of attempts while getting PEB
  ubi: Don't do anchor move within fastmap area
  ubifs: Remove redundant assignment to pointer fname

Pull UML updates from Richard Weinberger:

 - virtio support

 - fixes for our new time travel mode

 - various improvements to make lockdep and kasan work better

 - SPDX header updates

* tag 'for-linus-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: (25 commits)
  um: irq: Fix LAST_IRQ usage in init_IRQ()
  um: Add SPDX headers for files in arch/um/include
  um: Add SPDX headers for files in arch/um/os-Linux
  um: Add SPDX headers to files in arch/um/kernel/
  um: Add SPDX headers for files in arch/um/drivers
  um: virtio: Implement VHOST_USER_PROTOCOL_F_REPLY_ACK
  um: virtio: Implement VHOST_USER_PROTOCOL_F_SLAVE_REQ
  um: drivers: Add virtio vhost-user driver
  um: Use real DMA barriers
  um: Don't use generic barrier.h
  um: time-travel: Restrict time update in IRQ handler
  um: time-travel: Fix periodic timers
  um: Enable CONFIG_CONSTRUCTORS
  um: Place (soft)irq text with macros
  um: Fix VDSO compiler warning
  um: Implement TRACE_IRQFLAGS_SUPPORT
  um: Remove misleading #define ARCh_IRQ_ENABLED
  um: Avoid using uninitialized regs
  um: Remove sig_info[SIGALRM]
  um: Error handling fixes in vector drivers
  ...

Pull MTD updates from Richard Weinberger:
 "MTD core changes:
   - add debugfs nodes for querying the flash name and id
   - mtd parser reorganization

  SPI NOR core changes:
   - always use bounce buffer for register read/writes
   - move m25p80 code in spi-nor.c
   - rework hwcaps selection for the spi-mem case
   - rework the core in order to move the manufacturer specific code out
     of it:
       - regroup flash parameters in 'struct spi_nor_flash_parameter'
       - add default_init() and post_sfdp() hooks to tweak the flash
         parameters
       - introduce the ->set_4byte(), ->convert_addr() and ->setup()
         methods, to deal with manufacturer specific code
       - rework the SPI NOR lock/unlock logic
   - fix an error code in spi_nor_read_raw()
   - fix a memory leak bug
   - enable the debugfs for the partname and partid
   - add support for few flashes

  SPI NOR controller drivers changes:
   - intel-spi:
       - Whitelist 4B read commands
       - Add support for Intel Tiger Lake SPI serial flash
   - aspeed-smc: Add of_node_put()
   - hisi-sfc: add of_node_put()
   - cadence-quadspi: Fix QSPI RCU Schedule Stall

  NAND core:
   - Fixing typos
   - Adding missing of_node_put() in various drivers

  Raw NAND controller drivers:
   - Macronix: new controller driver
   - Omap2: fix the number of bitflips returned
   - Brcmnand: fix a pointer not iterating over all the page chunks
   - W90x900: driver removed
   - Onenand: fix a memory leak
   - Sharpsl: missing include guard
   - STM32: avoid warnings when building with W=1
   - Ingenic: fix a coccinelle warning
   - r852: call a helper to simplify the code

  CFI core:
   - Kill useless initializer in mtd_do_chip_probe()
   - Fix a rare write failure seen on some cfi_cmdset_0002 compliant
     Parallel NORs
   - Bunch of cleanups for cfi_cmdset_0002 driver's write functions by
     Tokunori Ikegami"

* tag 'mtd/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (77 commits)
  mtd: pmc551: Remove set but not used variable 'soff_lo'
  mtd: cfi_cmdset_0002: Fix do_erase_chip() to get chip as erasing mode
  mtd: sm_ftl: Fix memory leak in sm_init_zone() error path
  mtd: parsers: Move CMDLINE parser
  mtd: parsers: Move OF parser
  mtd: parsers: Move BCM63xx parser
  mtd: parsers: Move BCM47xx parser
  mtd: parsers: Move TI AR7 parser
  mtd: pismo: Simplify getting the adapter of a client
  mtd: phram: Module parameters add writable permissions
  mtd: pxa2xx: Use ioremap_cache insted of ioremap_cached
  mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"
  mtd: spi-nor: Add support for mt35xu02g
  mtd: rawnand: omap2: Fix number of bitflips reporting with ELM
  mtd: rawnand: brcmnand: Fix ecc chunk calculation for erased page bitfips
  mtd: spi-nor: remove superfluous pass of nor->info->sector_size
  mtd: spi-nor: enable the debugfs for the partname and partid
  mtd: mtdcore: add debugfs nodes for querying the flash name and id
  mtd: spi-nor: hisi-sfc: Add of_node_put() before break
  mtd: spi-nor: aspeed-smc: Add of_node_put()
  ...

Pull libnvdimm updates from Dan Williams:
 "Some reworks to better support nvdimms on powerpc and an nvdimm
  security interface update:

   - Rework the nvdimm core to accommodate architectures with different
     page sizes and ones that can change supported huge page sizes at
     boot time rather than a compile time constant.

   - Introduce a distinct 'frozen' attribute for the nvdimm security
     state since it is independent of the locked state.

   - Miscellaneous fixups"

* tag 'libnvdimm-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm: Use PAGE_SIZE instead of SZ_4K for align check
  libnvdimm/label: Remove the dpa align check
  libnvdimm/pfn_dev: Add page size and struct page size to pfn superblock
  libnvdimm/pfn_dev: Add a build check to make sure we notice when struct page size change
  libnvdimm/pmem: Advance namespace seed for specific probe errors
  libnvdimm/region: Rewrite _probe_success() to _advance_seeds()
  libnvdimm/security: Consolidate 'security' operations
  libnvdimm/security: Tighten scope of nvdimm->busy vs security operations
  libnvdimm/security: Introduce a 'frozen' attribute
  libnvdimm, region: Use struct_size() in kzalloc()
  tools/testing/nvdimm: Fix fallthrough warning
  libnvdimm/of_pmem: Provide a unique name for bus provider

Pull SCSI updates from James Bottomley:
 "This is mostly update of the usual drivers: qla2xxx, ufs, smartpqi,
  lpfc, hisi_sas, qedf, mpt3sas; plus a whole load of minor updates. The
  only core change this time around is the addition of request batching
  for virtio. Since batching requires an additional flag to use, it
  should be invisible to the rest of the drivers"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (264 commits)
  scsi: hisi_sas: Fix the conflict between device gone and host reset
  scsi: hisi_sas: Add BIST support for phy loopback
  scsi: hisi_sas: Add hisi_sas_debugfs_alloc() to centralise allocation
  scsi: hisi_sas: Remove some unused function arguments
  scsi: hisi_sas: Remove redundant work declaration
  scsi: hisi_sas: Remove hisi_sas_hw.slot_complete
  scsi: hisi_sas: Assign NCQ tag for all NCQ commands
  scsi: hisi_sas: Update all the registers after suspend and resume
  scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init device
  scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() fails
  scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabled
  scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()
  scsi: hisi_sas: add debugfs auto-trigger for internal abort time out
  scsi: virtio_scsi: unplug LUNs when events missed
  scsi: scsi_dh_rdac: zero cdb in send_mode_select()
  scsi: fcoe: fix null-ptr-deref Read in fc_release_transport
  scsi: ufs-hisi: use devm_platform_ioremap_resource() to simplify code
  scsi: ufshcd: use devm_platform_ioremap_resource() to simplify code
  scsi: hisi_sas: use devm_platform_ioremap_resource() to simplify code
  scsi: ufs: Use kmemdup in ufshcd_read_string_desc()
  ...

Merge tag 'for-5.4/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper updates from Mike Snitzer:

 - crypto and DM crypt advances that allow the crypto API to reclaim
   implementation details that do not belong in DM crypt. The wrapper
   template for ESSIV generation that was factored out will also be used
   by fscrypt in the future.

 - Add root hash pkcs#7 signature verification to the DM verity target.

 - Add a new "clone" DM target that allows for efficient remote
   replication of a device.

 - Enhance DM bufio's cache to be tailored to each client based on use.
   Clients that make heavy use of the cache get more of it, and those
   that use less have reduced cache usage.

 - Add a new DM_GET_TARGET_VERSION ioctl to allow userspace to query the
   version number of a DM target (even if the associated module isn't
   yet loaded).

 - Fix invalid memory access in DM zoned target.

 - Fix the max_discard_sectors limit advertised by the DM raid target;
   it was mistakenly storing the limit in bytes rather than sectors.

 - Small optimizations and cleanups in DM writecache target.

 - Various fixes and cleanups in DM core, DM raid1 and space map portion
   of DM persistent data library.

* tag 'for-5.4/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (22 commits)
  dm: introduce DM_GET_TARGET_VERSION
  dm bufio: introduce a global cache replacement
  dm bufio: remove old-style buffer cleanup
  dm bufio: introduce a global queue
  dm bufio: refactor adjust_total_allocated
  dm bufio: call adjust_total_allocated from __link_buffer and __unlink_buffer
  dm: add clone target
  dm raid: fix updating of max_discard_sectors limit
  dm writecache: skip writecache_wait for pmem mode
  dm stats: use struct_size() helper
  dm crypt: omit parsing of the encapsulated cipher
  dm crypt: switch to ESSIV crypto API template
  crypto: essiv - create wrapper template for ESSIV generation
  dm space map common: remove check for impossible sm_find_free() return value
  dm raid1: use struct_size() with kzalloc()
  dm writecache: optimize performance by sorting the blocks for writeback_all
  dm writecache: add unlikely for getting two block with same LBA
  dm writecache: remove unused member pointer in writeback_struct
  dm zoned: fix invalid memory access
  dm verity: add root hash pkcs#7 signature verification
  ...

Pull RDMA subsystem updates from Jason Gunthorpe:
 "This cycle mainly saw lots of bug fixes and clean up code across the
  core code and several drivers, few new functional changes were made.

   - Many cleanup and bug fixes for hns

   - Various small bug fixes and cleanups in hfi1, mlx5, usnic, qed,
     bnxt_re, efa

   - Share the query_port code between all the iWarp drivers

   - General rework and cleanup of the ODP MR umem code to fit better
     with the mmu notifier get/put scheme

   - Support rdma netlink in non init_net name spaces

   - mlx5 support for XRC devx and DC ODP"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (99 commits)
  RDMA: Fix double-free in srq creation error flow
  RDMA/efa: Fix incorrect error print
  IB/mlx5: Free mpi in mp_slave mode
  IB/mlx5: Use the original address for the page during free_pages
  RDMA/bnxt_re: Fix spelling mistake "missin_resp" -> "missing_resp"
  RDMA/hns: Package operations of rq inline buffer into separate functions
  RDMA/hns: Optimize cmd init and mode selection for hip08
  IB/hfi1: Define variables as unsigned long to fix KASAN warning
  IB/{rdmavt, hfi1, qib}: Add a counter for credit waits
  IB/hfi1: Add traces for TID RDMA READ
  RDMA/siw: Relax from kmap_atomic() use in TX path
  IB/iser: Support up to 16MB data transfer in a single command
  RDMA/siw: Fix page address mapping in TX path
  RDMA: Fix goto target to release the allocated memory
  RDMA/usnic: Avoid overly large buffers on stack
  RDMA/odp: Add missing cast for 32 bit
  RDMA/hns: Use devm_platform_ioremap_resource() to simplify code
  Documentation/infiniband: update name of some functions
  RDMA/cma: Fix false error message
  RDMA/hns: Fix wrong assignment of qp_access_flags
  ...

Pull hmm updates from Jason Gunthorpe:
 "This is more cleanup and consolidation of the hmm APIs and the very
  strongly related mmu_notifier interfaces. Many places across the tree
  using these interfaces are touched in the process. Beyond that a
  cleanup to the page walker API and a few memremap related changes
  round out the series:

   - General improvement of hmm_range_fault() and related APIs, more
     documentation, bug fixes from testing, API simplification &
     consolidation, and unused API removal

   - Simplify the hmm related kconfigs to HMM_MIRROR and DEVICE_PRIVATE,
     and make them internal kconfig selects

   - Hoist a lot of code related to mmu notifier attachment out of
     drivers by using a refcount get/put attachment idiom and remove the
     convoluted mmu_notifier_unregister_no_release() and related APIs.

   - General API improvement for the migrate_vma API and revision of its
     only user in nouveau

   - Annotate mmu_notifiers with lockdep and sleeping region debugging

  Two series unrelated to HMM or mmu_notifiers came along due to
  dependencies:

   - Allow pagemap's memremap_pages family of APIs to work without
     providing a struct device

   - Make walk_page_range() and related use a constant structure for
     function pointers"

* tag 'for-linus-hmm' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (75 commits)
  libnvdimm: Enable unit test infrastructure compile checks
  mm, notifier: Catch sleeping/blocking for !blockable
  kernel.h: Add non_block_start/end()
  drm/radeon: guard against calling an unpaired radeon_mn_unregister()
  csky: add missing brackets in a macro for tlb.h
  pagewalk: use lockdep_assert_held for locking validation
  pagewalk: separate function pointers from iterator data
  mm: split out a new pagewalk.h header from mm.h
  mm/mmu_notifiers: annotate with might_sleep()
  mm/mmu_notifiers: prime lockdep
  mm/mmu_notifiers: add a lockdep map for invalidate_range_start/end
  mm/mmu_notifiers: remove the __mmu_notifier_invalidate_range_start/end exports
  mm/hmm: hmm_range_fault() infinite loop
  mm/hmm: hmm_range_fault() NULL pointer bug
  mm/hmm: fix hmm_range_fault()'s handling of swapped out pages
  mm/mmu_notifiers: remove unregister_no_release
  RDMA/odp: remove ib_ucontext from ib_umem
  RDMA/odp: use mmu_notifier_get/put for 'struct ib_ucontext_per_mm'
  RDMA/mlx5: Use odp instead of mr->umem in pagefault_mr
  RDMA/mlx5: Use ib_umem_start instead of umem.address
  ...

Pull asm inline support from Miguel Ojeda:
 "Make use of gcc 9's "asm inline()" (Rasmus Villemoes):

  gcc 9+ (and gcc 8.3, 7.5) provides a way to override the otherwise
  crude heuristic that gcc uses to estimate the size of the code
  represented by an asm() statement. From the gcc docs

      If you use 'asm inline' instead of just 'asm', then for inlining
      purposes the size of the asm is taken as the minimum size, ignoring
      how many instructions GCC thinks it is.

  For compatibility with older compilers, we obviously want a

      #if [understands asm inline]
      #define asm_inline asm inline
      #else
      #define asm_inline asm
      #endif

  But since we #define the identifier inline to attach some attributes,
  we have to use an alternate spelling of that keyword. gcc provides
  both __inline__ and __inline, and we currently #define both to inline,
  so they all have the same semantics.

  We have to free up one of __inline__ and __inline, and the latter is
  by far the easiest.

  The two x86 changes cause smaller code gen differences than I'd
  expect, but I think we do want the asm_inline thing available sooner
  or later, so this is just to get the ball rolling"

* tag 'compiler-attributes-for-linus-v5.4' of git://github.com/ojeda/linux:
  x86: bug.h: use asm_inline in _BUG_FLAGS definitions
  x86: alternative.h: use asm_inline for all alternative variants
  compiler-types.h: add asm_inline definition
  compiler_types.h: don't #define __inline
  lib/zstd/mem.h: replace __inline by inline
  staging: rtl8723bs: replace __inline by inline

Pull gcc-plugins fix from Kees Cook:
 "Fix a potential problem in randomize_layout structure auto-selection
  (that was not triggered by any existing kernel structures)"

* tag 'gcc-plugins-v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  randstruct: Check member structs in is_pure_ops_struct()

Pull printk updates from Petr Mladek:

 - Fix off-by-one error when calculating messages that might fit into
   kmsg buffer. It causes occasional omitting of the last message.

 - Add missing pointer check in %pD format modifier handling.

 - Some clean up

* tag 'printk-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
  ABI: Update dev-kmsg documentation to match current kernel behaviour
  printk: Replace strncmp() with str_has_prefix()
  lib/test_printf: Remove obvious comments from %pd and %pD tests
  lib/test_printf: Add test of null/invalid pointer dereference for dentry
  vsprintf: Prevent crash when dereferencing invalid pointers for %pD
  printk: Do not lose last line in kmsg buffer dump

Pull ARM SoC late updates from Arnd Bergmann:
 "This is some material that we picked up into our tree late or that had
  complex inter-depondencies. The fact that there are these
  interdependencies tends to meant that these are often actually the
  most interesting new additions:

   - The new Aspeed AST2600 baseboard management controller is added,
     this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
     had some dependencies on other device drivers.

   - After many years, support for the MMP2 based OLPC XO-1.75 finally
     makes it into the kernel.

   - The Armada 3720 based Turris Mox open source router platform is a
     late addition and it follows some preparatory work across multiple
     branches.

   - The OMAP2+ platform had some large-scale cleanup involving driver
     changes and DT changes, here we finish it off, dropping a lot of
     the now-unused platform data.

   - The TI K3 platform that got added for 5.3 gains a lot more support
     for individual bits on the SoC, this part just came late for the
     merge window"

[ This pull request itself wasn't actually sent late at all by Arnd, but
  I waited on the branches that it used to be pulled first, so it ends
  up being merged much later than the other ARM SoC pull requests this
  merge window     - Linus ]

* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
  ARM: dts: dir685: Drop spi-cpol from the display
  ARM: dts: aspeed: Add AST2600 pinmux nodes
  ARM: dts: aspeed: Add AST2600 and EVB
  ARM: exynos: Enable support for ARM architected timers
  ARM: samsung: Fix system restart on S3C6410
  ARM: dts: mmp2: add OLPC XO 1.75 machine
  ARM: dts: mmp2: rename the USB PHY node
  ARM: dts: mmp2: specify reg-shift for the UARTs
  ARM: dts: mmp2: add camera interfaces
  ARM: dts: mmp2: fix the SPI nodes
  ARM: dts: mmp2: trivial whitespace fix
  arm64: dts: marvell: add DTS for Turris Mox
  dt-bindings: marvell: document Turris Mox compatible
  arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
  arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
  arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
  arm64: dts: ti: k3-j721e-main: Add hwspinlock node
  arm64: dts: ti: k3-am65-main: Add hwspinlock node
  arm64: dts: k3-j721e: Add gpio-keys on common processor board
  dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
  ...

Pull clk updates from Stephen Boyd:
 "We have a small collection of core framework updates this time, mostly
  around clk registration by clk providers and debugfs "nice to haves"
  for rate constraints. I'll highlight that we're now setting the
  clk_init_data pointer inside struct clk_hw to NULL during
  clk_register(), which may break some drivers that thought they could
  use that pointer during normal operations. That change has been
  sitting in next for a while now but maybe something is still broken.
  We'l see. Other than that the core framework changes aren't invasive
  and they're fixing bugs, simplifying, and making things better.

  On the clk driver side we got the usual addition of new SoC support,
  new features for existing drivers, and bug fixes scattered throughout.
  The biggest diffstat is the Amlogic driver that gained CPU clk support
  in addition to migrating to the new way of specifying clk parents.
  After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
  support for various new SoCs and clock controllers from those vendors.

  Core:
   - Drop NULL checks in clk debugfs
   - Add min/max rates to clk debugfs
   - Set clk_init_data pointer inside clk_hw to NULL after registration
   - Make clk_bulk_get_all() return an 'id' corresponding to clock-names
   - Evict parents from parent cache when they're unregistered

  New Drivers:
   - Add clock driver for i.MX8MN SoCs
   - Support aspeed AST2600 SoCs
   - Support for Mediatek MT6779 SoCs
   - Support qcom SM8150 GCC and RPMh clks
   - Support qcom QCS404 WCSS clks
   - Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
   - Addition of clock driver for Rockchip rk3308 SoCs

  Updates:
   - Add regulator support to the cdce925 clk driver
   - Add support for Raspberry Pi 4 bcm2711 SoCs
   - Add SDIO gate support to aspeed driver
   - Add missing of_node_put() calls in various clk drivers
   - Migrate Amlogic driver to new clock parent description method
   - Add DVFS support to Amlogic Meson g12
   - Add Amlogic Meson g12a reset support to the axg audio clock controller
   - Add sm1 support to the Amlogic Meson g12a clock controller
   - Switch i.MX8MM clock driver to platform driver
   - Add Hifi4 DSP related clocks for i.MX8QXP SoC
   - Fix Audio PLL setting and parent clock for USB
   - Misc i.MX8 clock driver improvements and corrections
   - Set floor ops for Qualcomm SD clks so that rounding works
   - Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
   - Enable the Allwinner V3 SoC and fix the i2s clock for H6"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
  clk: Drop !clk checks in debugfs dumping
  clk: imx: imx8mn: fix pll mux bit
  clk: imx: imx8mm: fix pll mux bit
  clk: imx: clk-pll14xx: unbypass PLL by default
  clk: imx: pll14xx: avoid glitch when set rate
  clk: mvebu: ap80x: add AP807 clock support
  clk: mvebu: ap806: Prepare the introduction of AP807 clock support
  clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
  clk: mvebu: ap806: be more explicit on what SaR is
  clk: mvebu: ap80x-cpu: add AP807 CPU clock support
  clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
  dt-bindings: ap806: Document AP807 clock compatible
  dt-bindings: ap80x: Document AP807 CPU clock compatible
  clk: sprd: add missing kfree
  clk: at91: allow 24 Mhz clock as input for PLL
  clk: Make clk_bulk_get_all() return a valid "id"
  clk: actions: Fix factor clk struct member access
  clk: qcom: rcg: Return failure for RCG update
  clk: remove extra ---help--- tags in Kconfig
  clk: add include guard to clk-conf.h
  ...

Pull VFIO updates from Alex Williamson:

 - Fix spapr iommu error case case (Alexey Kardashevskiy)

 - Consolidate region type definitions (Cornelia Huck)

 - Restore saved original PCI state on release (hexin)

 - Simplify mtty sample driver interrupt path (Parav Pandit)

 - Support for reporting valid IOVA regions to user (Shameer Kolothum)

* tag 'vfio-v5.4-rc1' of git://github.com/awilliam/linux-vfio:
  vfio_pci: Restore original state on release
  vfio/type1: remove duplicate retrieval of reserved regions
  vfio/type1: Add IOVA range capability support
  vfio/type1: check dma map request is within a valid iova range
  vfio/spapr_tce: Fix incorrect tce_iommu_group memory free
  vfio-mdev/mtty: Simplify interrupt generation
  vfio: re-arrange vfio region definitions
  vfio/type1: Update iova list on detach
  vfio/type1: Check reserved region conflict and update iova list
  vfio/type1: Introduce iova list and add iommu aperture validity check

2 recent commits have fixed issues where _PFN_SHIFT grew too large due
to the introduction of too many pgprot bits in our PTEs for some MIPS32
kernel configurations. Tracking down such issues can be tricky, so add a
BUILD_BUG_ON() to help.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org

Commit 61cbfff4 ("MIPS: pte_special()/pte_mkspecial() support")
added a _PAGE_SPECIAL bit to the pgprot bits of our PTEs. Unfortunately
for MIPS32 configurations with RiXi support this pushed the number of
pgprot bits to 13. Since the PFN field in EntryLo begins at bit 12 this
results in us shifting the most significant bit of the physical address
beyond the end of the PTE, leading any mapped access to a physical
address above 2GB to incorrectly access an address 2GB lower than
intended.

For now, disable the pte_special() support for MIPS32 configurations
that support RiXi.

Fixes: 61cbfff4 ("MIPS: pte_special()/pte_mkspecial() support")
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Dmitry Korotin <dkorotin@wavecomp.com>
Cc: linux-mips@vger.kernel.org

Pull powerpc updates from Michael Ellerman:
 "This is a bit late, partly due to me travelling, and partly due to a
  power outage knocking out some of my test systems *while* I was
  travelling.

   - Initial support for running on a system with an Ultravisor, which
     is software that runs below the hypervisor and protects guests
     against some attacks by the hypervisor.

   - Support for building the kernel to run as a "Secure Virtual
     Machine", ie. as a guest capable of running on a system with an
     Ultravisor.

   - Some changes to our DMA code on bare metal, to allow devices with
     medium sized DMA masks (> 32 && < 59 bits) to use more than 2GB of
     DMA space.

   - Support for firmware assisted crash dumps on bare metal (powernv).

   - Two series fixing bugs in and refactoring our PCI EEH code.

   - A large series refactoring our exception entry code to use gas
     macros, both to make it more readable and also enable some future
     optimisations.

  As well as many cleanups and other minor features & fixups.

  Thanks to: Adam Zerella, Alexey Kardashevskiy, Alistair Popple, Andrew
  Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman Khandual,
  Balbir Singh, Benjamin Herrenschmidt, Cédric Le Goater, Christophe
  JAILLET, Christophe Leroy, Christopher M. Riedl, Christoph Hellwig,
  Claudio Carvalho, Daniel Axtens, David Gibson, David Hildenbrand,
  Desnes A. Nunes do Rosario, Ganesh Goudar, Gautham R. Shenoy, Greg
  Kurz, Guerney Hunt, Gustavo Romero, Halil Pasic, Hari Bathini, Joakim
  Tjernlund, Jonathan Neuschafer, Jordan Niethe, Leonardo Bras, Lianbo
  Jiang, Madhavan Srinivasan, Mahesh Salgaonkar, Mahesh Salgaonkar,
  Masahiro Yamada, Maxiwell S. Garcia, Michael Anderson, Nathan
  Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Oliver
  O'Halloran, Qian Cai, Ram Pai, Ravi Bangoria, Reza Arbab, Ryan Grimm,
  Sam Bobroff, Santosh Sivaraj, Segher Boessenkool, Sukadev Bhattiprolu,
  Thiago Bauermann, Thiago Jung Bauermann, Thomas Gleixner, Tom
  Lendacky, Vasant Hegde"

* tag 'powerpc-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (264 commits)
  powerpc/mm/mce: Keep irqs disabled during lockless page table walk
  powerpc: Use ftrace_graph_ret_addr() when unwinding
  powerpc/ftrace: Enable HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
  ftrace: Look up the address of return_to_handler() using helpers
  powerpc: dump kernel log before carrying out fadump or kdump
  docs: powerpc: Add missing documentation reference
  powerpc/xmon: Fix output of XIVE IPI
  powerpc/xmon: Improve output of XIVE interrupts
  powerpc/mm/radix: remove useless kernel messages
  powerpc/fadump: support holes in kernel boot memory area
  powerpc/fadump: remove RMA_START and RMA_END macros
  powerpc/fadump: update documentation about option to release opalcore
  powerpc/fadump: consider f/w load area
  powerpc/opalcore: provide an option to invalidate /sys/firmware/opal/core file
  powerpc/opalcore: export /sys/firmware/opal/core for analysing opal crashes
  powerpc/fadump: update documentation about CONFIG_PRESERVE_FA_DUMP
  powerpc/fadump: add support to preserve crash data on FADUMP disabled kernel
  powerpc/fadump: improve how crashed kernel's memory is reserved
  powerpc/fadump: consider reserved ranges while releasing memory
  powerpc/fadump: make crash memory ranges array allocation generic
  ...

Pull arm64 fixes from Will Deacon:
 "We've had a few arm64 fixes trickle in this week. Nothing catastophic,
  but all things that should be addressed:

   - Fix clang build breakage with CONFIG_OPTIMIZE_INLINING=y

   - Fix compilation of pointer tagging selftest

   - Fix COND_SYSCALL definitions to work with CFI checks

   - Fix stale documentation reference in our Kconfig"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: Fix reference to docs for ARM64_TAGGED_ADDR_ABI
  arm64: fix function types in COND_SYSCALL
  selftests, arm64: add kernel headers path for tags_test
  arm64: fix unreachable code issue with cmpxchg

Pull Hexagon maintainership update from Richard Kuo:
 "I am leaving QuIC, and Brian Cain will be taking over maintainership
  of the Hexagon port"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
  Hexagon: change maintainer to Brian Cain

Pull tracing updates from Steven Rostedt:

 - Addition of multiprobes to kprobe and uprobe events (allows for more
   than one probe attached to the same location)

 - Addition of adding immediates to probe parameters

 - Clean up of the recordmcount.c code. This brings us closer to merging
   recordmcount into objtool, and reuse code.

 - Other small clean ups

* tag 'trace-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (33 commits)
  selftests/ftrace: Update kprobe event error testcase
  tracing/probe: Reject exactly same probe event
  tracing/probe: Fix to allow user to enable events on unloaded modules
  selftests/ftrace: Select an existing function in kprobe_eventname test
  tracing/kprobe: Fix NULL pointer access in trace_porbe_unlink()
  tracing: Make sure variable reference alias has correct var_ref_idx
  tracing: Be more clever when dumping hex in __print_hex()
  ftrace: Simplify ftrace hash lookup code in clear_func_from_hash()
  tracing: Add "gfp_t" support in synthetic_events
  tracing: Rename tracing_reset() to tracing_reset_cpu()
  tracing: Document the stack trace algorithm in the comments
  tracing/arm64: Have max stack tracer handle the case of return address after data
  recordmcount: Clarify what cleanup() does
  recordmcount: Remove redundant cleanup() calls
  recordmcount: Kernel style formatting
  recordmcount: Kernel style function signature formatting
  recordmcount: Rewrite error/success handling
  selftests/ftrace: Add syntax error test for multiprobe
  selftests/ftrace: Add syntax error test for immediates
  selftests/ftrace: Add a testcase for kprobe multiprobe event
  ...