- 21 Dec, 2011 27 commits
-
-
Eryu Guan authored
commit 8762202d upstream. I hit a J_ASSERT(blocknr != 0) failure in cleanup_journal_tail() when mounting a fsfuzzed ext3 image. It turns out that the corrupted ext3 image has s_first = 0 in journal superblock, and the 0 is passed to journal->j_head in journal_reset(), then to blocknr in cleanup_journal_tail(), in the end the J_ASSERT failed. So validate s_first after reading journal superblock from disk in journal_get_superblock() to ensure s_first is valid. The following script could reproduce it: fstype=ext3 blocksize=1024 img=$fstype.img offset=0 found=0 magic="c0 3b 39 98" dd if=/dev/zero of=$img bs=1M count=8 mkfs -t $fstype -b $blocksize -F $img filesize=`stat -c %s $img` while [ $offset -lt $filesize ] do if od -j $offset -N 4 -t x1 $img | grep -i "$magic";then echo "Found journal: $offset" found=1 break fi offset=`echo "$offset+$blocksize" | bc` done if [ $found -ne 1 ];then echo "Magic \"$magic\" not found" exit 1 fi dd if=/dev/zero of=$img seek=$(($offset+23)) conv=notrunc bs=1 count=1 mkdir -p ./mnt mount -o loop $img ./mnt Cc: Jan Kara <jack@suse.cz> Signed-off-by:
Eryu Guan <guaneryu@gmail.com> Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Cc: Moritz Mühlenhoff <jmm@inutil.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Mark Langsdorf authored
commit 2ded6e6a upstream. When HPET is operating in RTC mode, the TN_ENABLE bit on timer1 controls whether the HPET or the RTC delivers interrupts to irq8. When the system goes into suspend, the RTC driver sends a signal to the HPET driver so that the HPET releases control of irq8, allowing the RTC to wake the system from suspend. The switchover is accomplished by a write to the HPET configuration registers which currently only occurs while servicing the HPET interrupt. On some systems, I have seen the system suspend before an HPET interrupt occurs, preventing the write to the HPET configuration register and leaving the HPET in control of the irq8. As the HPET is not active during suspend, it does not generate a wake signal and RTC alarms do not work. This patch forces the HPET driver to immediately transfer control of the irq8 channel to the RTC instead of waiting until the next interrupt event. Signed-off-by:
Mark Langsdorf <mark.langsdorf@amd.com> Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.comTested-by:
Andreas Herrmann <andreas.herrmann3@amd.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Sascha Hauer authored
commit e58f516f upstream. When we can't configure the dma channel we want to fall back to PIO. We do this by setting host->do_dma to zero. This does not work as do_dma is used to see whether dma can be used for the current transfer. Instead, we have to set host->dma to NULL. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Axel Lin authored
commit 0b57d760 upstream. wait_for_completion_interruptible_timeout() may return negative value. In this case, checking if (t > 0) will return true if t is unsigned. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by:
-
Linus Torvalds authored
commit 13c07b02 upstream. Exactly like roundup_pow_of_two(1), the rounddown version was buggy for the case of a compile-time constant '1' argument. Probably because it originated from the same code, sharing history with the roundup version from before the bugfix (for that one, see commit 1a06a52e: "Fix roundup_pow_of_two(1)"). However, unlike the roundup version, the fix for rounddown is to just remove the broken special case entirely. It's simply not needed - the generic code 1UL << ilog2(n) does the right thing for the constant '1' argment too. The only reason roundup needed that special case was because rounding up does so by subtracting one from the argument (and then adding one to the result) causing the obvious problems with "ilog2(0)". But rounddown doesn't do any of that, since ilog2() naturally truncates (ie "rounds down") to the right rounded down value. And without the ilog2(0) case, there's no reason for the special case that had the wrong value. tl;dr: rounddown_pow_of_two(1) should be 1, not 0. Acked-by:
Dmitry Torokhov <dtor@vmware.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Nikolay Martynov authored
Upstream commit d305a655. If addBA responses comes in just after addba_resp_timer has expired mac80211 will still accept it and try to open the aggregation session. This causes drivers to be confused and in some cases even crash. This patch fixes the race condition and makes sure that if addba_resp_timer has expired addBA response is not longer accepted and we do not try to open half-closed session. Signed-off-by:
Nikolay Martynov <mar.kolya@gmail.com> [some adjustments] Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Wey-Yi Guy authored
commit 34a5b4b6 upstream. The ht40 setting should not change after association unless channel switch This fix a problem we are seeing which cause uCode assert because driver sending invalid information and make uCode confuse Here is the firmware assert message: kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000. kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301 kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump: kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6 kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1 kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2 kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1 kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2 kernel: iwlagn 0000:03:00.0: 0x01008035 | data1 kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2 kernel: iwlagn 0000:03:00.0: 0x000005A7 | line kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1 kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2 kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3 kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version kernel: iwlagn 0000:03:00.0: 0x00480303 | board version kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd kernel: iwlagn 0000:03:00.0: CSR values: kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG) kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303 kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40 kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030 kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5 kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0 kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001 kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001 kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044 kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078 kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2 kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200 kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000 kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010 kernel: iwlagn 0000:03:00.0: FH register values: kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0 kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060 kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000 kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001 kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000 kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries kernel: ------------[ cut here ]------------ WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407() kernel: Hardware name: 4290W4H kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2 kernel: Call Trace: kernel: [<ffffffff81036558>] ? warn_slowpath_common+0x73/0x87 kernel: [<ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407 kernel: [<ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32 kernel: [<ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87 kernel: [<ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3 kernel: [<ffffffff810480c9>] ? worker_thread+0x17a/0x23a kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b kernel: [<ffffffff8104ba97>] ? kthread+0x7a/0x82 kernel: [<ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10 kernel: [<ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11 kernel: [<ffffffff813d21b0>] ? gs_change+0xb/0xb Reported-by:
Udo Steinberg <udo@hypervisor.org> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by:
-
Tejun Heo authored
commit a855b84c upstream. Percpu allocator recorded the cpus which map to the first and last units in pcpu_first/last_unit_cpu respectively and used them to determine the address range of a chunk - e.g. it assumed that the first unit has the lowest address in a chunk while the last unit has the highest address. This simply isn't true. Groups in a chunk can have arbitrary positive or negative offsets from the previous one and there is no guarantee that the first unit occupies the lowest offset while the last one the highest. Fix it by actually comparing unit offsets to determine cpus occupying the lowest and highest offsets. Also, rename pcu_first/last_unit_cpu to pcpu_low/high_unit_cpu to avoid confusion. The chunk address range is used to flush cache on vmalloc area map/unmap and decide whether a given address is in the first chunk by per_cpu_ptr_to_phys() and the bug was discovered by invalid per_cpu_ptr_to_phys() translation for crash_note. Kudos to Dave Young for tracking down the problem. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
WANG Cong <xiyou.wangcong@gmail.com> Reported-by:
Dave Young <dyoung@redhat.com> Tested-by:
Thomas Renninger <trenn@suse.de> Signed-off-by:
-
Allen Kay authored
commit 4399c8bf upstream. If target_level == 0, current code breaks out of the while-loop if SUPERPAGE bit is set. We should also break out if PTE is not present. If we don't do this, KVM calls to iommu_iova_to_phys() will cause pfn_to_dma_pte() to create mapping for 4KiB pages. Signed-off-by:
Allen Kay <allen.m.kay@intel.com> Signed-off-by:
David Woodhouse <David.Woodhouse@intel.com> Signed-off-by:
Youquan Song <youquan.song@intel.com> Signed-off-by:
-
Allen Kay authored
commit 8140a95d upstream. set dmar->iommu_superpage field to the smallest common denominator of super page sizes supported by all active VT-d engines. Initialize this field in intel_iommu_domain_init() API so intel_iommu_map() API will be able to use iommu_superpage field to determine the appropriate super page size to use. Signed-off-by:
-
Allen Kay authored
commit 292827cb upstream. iommu_unmap() API expects IOMMU drivers to return the actual page order of the address being unmapped. Previous code was just returning page order passed in from the caller. This patch fixes this problem. Signed-off-by:
-
Roland Dreier authored
commit 9b5cd7f3 upstream. SBC-3 says: A TRANSFER LENGTH field set to zero specifies that 256 logical blocks shall be written. Any other value specifies the number of logical blocks that shall be written. The old code was always just returning the value in the TRANSFER LENGTH byte. Fix this to return 256 if the byte is 0. Signed-off-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Al Viro authored
commit 02125a82 upstream. __d_path() API is asking for trouble and in case of apparmor d_namespace_path() getting just that. The root cause is that when __d_path() misses the root it had been told to look for, it stores the location of the most remote ancestor in *root. Without grabbing references. Sure, at the moment of call it had been pinned down by what we have in *path. And if we raced with umount -l, we could have very well stopped at vfsmount/dentry that got freed as soon as prepend_path() dropped vfsmount_lock. It is safe to compare these pointers with pre-existing (and known to be still alive) vfsmount and dentry, as long as all we are asking is "is it the same address?". Dereferencing is not safe and apparmor ended up stepping into that. d_namespace_path() really wants to examine the place where we stopped, even if it's not connected to our namespace. As the result, it looked at ->d_sb->s_magic of a dentry that might've been already freed by that point. All other callers had been careful enough to avoid that, but it's really a bad interface - it invites that kind of trouble. The fix is fairly straightforward, even though it's bigger than I'd like: * prepend_path() root argument becomes const. * __d_path() is never called with NULL/NULL root. It was a kludge to start with. Instead, we have an explicit function - d_absolute_root(). Same as __d_path(), except that it doesn't get root passed and stops where it stops. apparmor and tomoyo are using it. * __d_path() returns NULL on path outside of root. The main caller is show_mountinfo() and that's precisely what we pass root for - to skip those outside chroot jail. Those who don't want that can (and do) use d_path(). * __d_path() root argument becomes const. Everyone agrees, I hope. * apparmor does *NOT* try to use __d_path() or any of its variants when it sees that path->mnt is an internal vfsmount. In that case it's definitely not mounted anywhere and dentry_path() is exactly what we want there. Handling of sysctl()-triggered weirdness is moved to that place. * if apparmor is asked to do pathname relative to chroot jail and __d_path() tells it we it's not in that jail, the sucker just calls d_absolute_path() instead. That's the other remaining caller of __d_path(), BTW. * seq_path_root() does _NOT_ return -ENAMETOOLONG (it's stupid anyway - the normal seq_file logics will take care of growing the buffer and redoing the call of ->show() just fine). However, if it gets path not reachable from root, it returns SEQ_SKIP. The only caller adjusted (i.e. stopped ignoring the return value as it used to do). Reviewed-by:
John Johansen <john.johansen@canonical.com> ACKed-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Mel Gorman authored
commit 1368edf0 upstream. Commit f5252e00 ("mm: avoid null pointer access in vm_struct via /proc/vmallocinfo") adds newly allocated vm_structs to the vmlist after it is fully initialised. Unfortunately, it did not check that __vmalloc_area_node() successfully populated the area. In the event of allocation failure, the vmalloc area is freed but the pointer to freed memory is inserted into the vmlist leading to a a crash later in get_vmalloc_info(). This patch adds a check for ____vmalloc_area_node() failure within __vmalloc_node_range. It does not use "goto fail" as in the previous error path as a warning was already displayed by __vmalloc_area_node() before it called vfree in its failure path. Credit goes to Luciano Chavez for doing all the real work of identifying exactly where the problem was. Signed-off-by:
Mel Gorman <mgorman@suse.de> Reported-by:
Luciano Chavez <lnx1138@linux.vnet.ibm.com> Tested-by:
Rik van Riel <riel@redhat.com> Acked-by:
David Rientjes <rientjes@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Michal Hocko authored
commit d0215638 upstream. setup_zone_migrate_reserve() expects that zone->start_pfn starts at pageblock_nr_pages aligned pfn otherwise we could access beyond an existing memblock resulting in the following panic if CONFIG_HOLES_IN_ZONE is not configured and we do not check pfn_valid: IP: [<c02d331d>] setup_zone_migrate_reserve+0xcd/0x180 *pdpt = 0000000000000000 *pde = f000ff53f000ff53 Oops: 0000 [#1] SMP Pid: 1, comm: swapper Not tainted 3.0.7-0.7-pae #1 VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform EIP: 0060:[<c02d331d>] EFLAGS: 00010006 CPU: 0 EIP is at setup_zone_migrate_reserve+0xcd/0x180 EAX: 000c0000 EBX: f5801fc0 ECX: 000c0000 EDX: 00000000 ESI: 000c01fe EDI: 000c01fe EBP: 00140000 ESP: f2475f58 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process swapper (pid: 1, ti=f2474000 task=f2472cd0 task.ti=f2474000) Call Trace: [<c02d389c>] __setup_per_zone_wmarks+0xec/0x160 [<c02d3a1f>] setup_per_zone_wmarks+0xf/0x20 [<c08a771c>] init_per_zone_wmark_min+0x27/0x86 [<c020111b>] do_one_initcall+0x2b/0x160 [<c086639d>] kernel_init+0xbe/0x157 [<c05cae26>] kernel_thread_helper+0x6/0xd Code: a5 39 f5 89 f7 0f 46 fd 39 cf 76 40 8b 03 f6 c4 08 74 32 eb 91 90 89 c8 c1 e8 0e 0f be 80 80 2f 86 c0 8b 14 85 60 2f 86 c0 89 c8 <2b> 82 b4 12 00 00 c1 e0 05 03 82 ac 12 00 00 8b 00 f6 c4 08 0f EIP: [<c02d331d>] setup_zone_migrate_reserve+0xcd/0x180 SS:ESP 0068:f2475f58 CR2: 00000000000012b4 We crashed in pageblock_is_reserved() when accessing pfn 0xc0000 because highstart_pfn = 0x36ffe. The issue was introduced in 3.0-rc1 by 6d3163ce ("mm: check if any page in a pageblock is reserved before marking it MIGRATE_RESERVE"). Make sure that start_pfn is always aligned to pageblock_nr_pages to ensure that pfn_valid s always called at the start of each pageblock. Architectures with holes in pageblocks will be correctly handled by pfn_valid_within in pageblock_is_reserved. Signed-off-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
Dang Bo <bdang@vmware.com> Reviewed-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Arve Hjnnevg <arve@android.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Dave Hansen <dave@linux.vnet.ibm.com> Signed-off-by:
-
Thomas Gleixner authored
commit d68fb11c upstream. The clock_getres() function must return the resolution in the timespec argument and return 0 for success. Signed-off-by:
John Stultz <john.stultz@linaro.org> Cc: Richard Cochran <richard.cochran@omicron.at> Signed-off-by:
-
Youquan Song authored
commit 58a84aa9 upstream. Commit 70b50f94 ("mm: thp: tail page refcounting fix") keeps all page_tail->_count zero at all times. But the current kernel does not set page_tail->_count to zero if a 1GB page is utilized. So when an IOMMU 1GB page is used by KVM, it wil result in a kernel oops because a tail page's _count does not equal zero. kernel BUG at include/linux/mm.h:386! invalid opcode: 0000 [#1] SMP Call Trace: gup_pud_range+0xb8/0x19d get_user_pages_fast+0xcb/0x192 ? trace_hardirqs_off+0xd/0xf hva_to_pfn+0x119/0x2f2 gfn_to_pfn_memslot+0x2c/0x2e kvm_iommu_map_pages+0xfd/0x1c1 kvm_iommu_map_memslots+0x7c/0xbd kvm_iommu_map_guest+0xaa/0xbf kvm_vm_ioctl_assigned_device+0x2ef/0xa47 kvm_vm_ioctl+0x36c/0x3a2 do_vfs_ioctl+0x49e/0x4e4 sys_ioctl+0x5a/0x7c system_call_fastpath+0x16/0x1b RIP gup_huge_pud+0xf2/0x159 Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Signed-off-by:
-
Youquan Song authored
commit b6999b19 upstream. With the 3.2-rc kernel, IOMMU 2M pages in KVM works. But when I tried to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page failed to be used. The root cause is that 1GB page allocation calls gup_huge_pud() while 2M page calls gup_huge_pmd. If compound pages are used and the page is a tail page, gup_huge_pmd() increases _mapcount to record tail page are mapped while gup_huge_pud does not do that. So when the mapped page is relesed, it will result in kernel oops because the page is not marked mapped. This patch add tail process for compound page in 1GB huge page which keeps the same process as 2M page. Reproduce like: 1. Add grub boot option: hugepagesz=1G hugepages=8 2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages 3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages -net none -device pci-assign,host=07:00.1 kernel BUG at mm/swap.c:114! invalid opcode: 0000 [#1] SMP Call Trace: put_page+0x15/0x37 kvm_release_pfn_clean+0x31/0x36 kvm_iommu_put_pages+0x94/0xb1 kvm_iommu_unmap_memslots+0x80/0xb6 kvm_assign_device+0xba/0x117 kvm_vm_ioctl_assigned_device+0x301/0xa47 kvm_vm_ioctl+0x36c/0x3a2 do_vfs_ioctl+0x49e/0x4e4 sys_ioctl+0x5a/0x7c system_call_fastpath+0x16/0x1b RIP put_compound_page+0xd4/0x168 Signed-off-by:
-
Claudio Scordino authored
commit b53fc7c2 upstream. Fix the error message "directives may not be used inside a macro argument" which appears when the kernel is compiled for the cris architecture. Signed-off-by:
Claudio Scordino <claudio@evidence.eu.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by:
-
Mark Brown authored
commit cefcc03f upstream. Allow userspace applications to do more parameter setting by providing a more complete stub DMA driver specifying a wildcard set of formats and channels and essentially random values for the DMA parameters. This is required for useful runtime operation of the dummy DMA driver until we are able to figure out how to power up links and do hw_params() from DAPM. Sending to stable as without this the dummy driver is not terribly useful. Reported-by:
Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com> Tested-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
Hans Verkuil authored
commit 83713fc9 upstream. The function setup_vpif_input_channel_mode() used the VSCLKDIS register instead of VIDCLKCTL. This meant that when in HD mode videoport channel 0 used a different clock from channel 1. Clearly a copy-and-paste error. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Acked-by:
Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Jean-Christophe PLAGNIOL-VILLARD authored
commit 1808958d upstream. The conid is supposed to be t0/t1/t2_clk. Signed-off-by:
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Wolfram Sang authored
commit 11357be9 upstream. Adding the machine_is_* line was forgotten when converting mach-stmp378x to mach-mxs. Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Manjunathappa, Prakash authored
commit f1b21c52 upstream. On OMAP-L138 platform, EDMA event queue 0 should be used for audio transfers so that they are not starved by video data moving on event queue 1. Commit 48519f0a (ASoC: davinci: let platform data define edma queue numbers) had a side-effect of changing this behavior by making the driver actually honor the platform data passed. Fix this now by passing event queue 0 as the queue to be used for audio transfers. Signed-off-by:
Manjunathappa, Prakash <prakash.pm@ti.com> Signed-off-by:
-
Thomas Gleixner authored
commit c9c024b3 upstream. The expiry function compares the timer against current time and does not expire the timer when the expiry time is >= now. That's wrong. If the timer is set for now, then it must expire. Make the condition expiry > now for breaking out the loop. Signed-off-by:
-
Takashi Iwai authored
commit cce4aa37 upstream. When no imux is available (e.g. a single capture source), alc_auto_init_input_src() may trigger an Oops due to the access to -1. Add a proper zero-check to avoid it. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
David Dillow authored
commit fc084e0b upstream. There are some AC97 codec and board combinations that have been observed to take a very long time to respond after the cold reset has completed. In one case, more than 350 ms was required. To allow users to have sound on those platforms, we'll wait up to 500ms for the codec to become ready. As a board may have multiple codecs, with some faster than others to reset, we add a module parameter to inform the driver which codecs should be present. Reported-by:
KotCzarny <tjosko@yahoo.com> Signed-off-by:
David Dillow <dave@thedillows.org> Signed-off-by:
-
- 09 Dec, 2011 13 commits
-
-
Greg Kroah-Hartman authored
-
Thomas Gleixner authored
commit de28f25e upstream. If a device is shutdown, then there might be a pending interrupt, which will be processed after we reenable interrupts, which causes the original handler to be run. If the old handler is the (broadcast) periodic handler the shutdown state might hang the kernel completely. Signed-off-by:
-
Yang Honggang (Joseph) authored
commit b1f91966 upstream. In order to leave a margin of 12.5% we should >> 3 not >> 5. Signed-off-by:
Yang Honggang (Joseph) <eagle.rtlinux@gmail.com> [jstultz: Modified commit subject] Signed-off-by:
-
Robert Richter authored
commit 87121ca5 upstream. Oprofile may crash in a KVM guest while unlaoding modules. This happens if oprofile_arch_init() fails and oprofile switches to the hr timer mode as a fallback. In this case oprofile_arch_exit() is called, but it never was initialized properly which causes the crash. This patch fixes this. oprofile: using timer interrupt. BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 IP: [<ffffffff8123c226>] unregister_syscore_ops+0x41/0x58 PGD 41da3f067 PUD 41d80e067 PMD 0 Oops: 0002 [#1] PREEMPT SMP CPU 5 Modules linked in: oprofile(-) Pid: 2382, comm: modprobe Not tainted 3.1.0-rc7-00018-g709a39d #18 Advanced Micro Device Anaheim/Anaheim RIP: 0010:[<ffffffff8123c226>] [<ffffffff8123c226>] unregister_syscore_ops+0x41/0x58 RSP: 0018:ffff88041de1de98 EFLAGS: 00010296 RAX: 0000000000000000 RBX: ffffffffa00060e0 RCX: dead000000200200 RDX: 0000000000000000 RSI: dead000000100100 RDI: ffffffff8178c620 RBP: ffff88041de1dea8 R08: 0000000000000001 R09: 0000000000000082 R10: 0000000000000000 R11: ffff88041de1dde8 R12: 0000000000000080 R13: fffffffffffffff5 R14: 0000000000000001 R15: 0000000000610210 FS: 00007f9ae5bef700(0000) GS:ffff88042fd40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000008 CR3: 000000041ca44000 CR4: 00000000000006e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process modprobe (pid: 2382, threadinfo ffff88041de1c000, task ffff88042db6d040) Stack: ffff88041de1deb8 ffffffffa0006770 ffff88041de1deb8 ffffffffa000251e ffff88041de1dec8 ffffffffa00022c2 ffff88041de1ded8 ffffffffa0004993 ffff88041de1df78 ffffffff81073115 656c69666f72706f 0000000000610200 Call Trace: [<ffffffffa000251e>] op_nmi_exit+0x15/0x17 [oprofile] [<ffffffffa00022c2>] oprofile_arch_exit+0xe/0x10 [oprofile] [<ffffffffa0004993>] oprofile_exit+0x13/0x15 [oprofile] [<ffffffff81073115>] sys_delete_module+0x1c3/0x22f [<ffffffff811bf09e>] ? trace_hardirqs_on_thunk+0x3a/0x3f [<ffffffff8148070b>] system_call_fastpath+0x16/0x1b Code: 20 c6 78 81 e8 c5 cc 23 00 48 8b 13 48 8b 43 08 48 be 00 01 10 00 00 00 ad de 48 b9 00 02 20 00 00 00 ad de 48 c7 c7 20 c6 78 81 89 42 08 48 89 10 48 89 33 48 89 4b 08 e8 a6 c0 23 00 5a 5b RIP [<ffffffff8123c226>] unregister_syscore_ops+0x41/0x58 RSP <ffff88041de1de98> CR2: 0000000000000008 ---[ end trace 06d4e95b6aa3b437 ]--- Signed-off-by:
Robert Richter <robert.richter@amd.com> Signed-off-by:
-
Gleb Natapov authored
commit bbbf7af4 upstream. If cpu A calls jump_label_inc() just after atomic_add_return() is called by cpu B, atomic_inc_not_zero() will return value greater then zero and jump_label_inc() will return to a caller before jump_label_update() finishes its job on cpu B. Link: http://lkml.kernel.org/r/20111018175551.GH17571@redhat.com Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by:
Jason Baron <jbaron@redhat.com> Signed-off-by:
Gleb Natapov <gleb@redhat.com> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt authored
commit d06c27b2 upstream. A update is made to the sched:sched_switch event that adds some logic to the first parameter of the __print_flags() that shows the state of tasks. This change cause perf to fail parsing the flags. A simple fix is needed to have the parser be able to process ops within the argument. Reported-by:
Andrew Vagin <avagin@openvz.org> Signed-off-by:
-
Thomas Gleixner authored
commit c1be8430 upstream. When a better rated broadcast device is installed, then the current active device is not disabled, which results in two running broadcast devices. Signed-off-by:
-
Ilya Dryomov authored
commit cb599747 upstream. Fix a bug introduced by e9dbfae5, which prevents event_subsystem from ever being released. Ref_count was added to keep track of subsystem users, not for counting events. Subsystem is created with ref_count = 1, so there is no need to increment it for every event, we have nr_events for that. Fix this by touching ref_count only when we actually have a new user - subsystem_open(). Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Link: http://lkml.kernel.org/r/1320052062-7846-1-git-send-email-idryomov@gmail.comSigned-off-by:
-
Rabin Vincent authored
commit c0afabd3 upstream. Currently, the RTC code does not disable the alarm in the hardware. This means that after a sequence such as the one below (the files are in the RTC sysfs), the box will boot up after 2 minutes even though we've asked for the alarm to be turned off. # echo $((`cat since_epoch`)+120) > wakealarm # echo 0 > wakealarm # poweroff Fix this by disabling the alarm when there are no timers to run. Cc: John Stultz <john.stultz@linaro.org> Signed-off-by:
Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by:
-
Tejun Heo authored
commit d3d9acf6 upstream. ftrace_event_call->filter is sched RCU protected but didn't use rcu_assign_pointer(). Use it. TODO: Add proper __rcu annotation to call->filter and all its users. -v2: Use RCU_INIT_POINTER() for %NULL clearing as suggested by Eric. Link: http://lkml.kernel.org/r/20111123164949.GA29639@google.com Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Signed-off-by:
-
Christoph Hellwig authored
commit 4c393a60 upstream. With Dmitry fsstress updates I've seen very reproducible crashes in xfs_attr_shortform_remove because xfs_attr_shortform_bytesfit claims that the attributes would not fit inline into the inode after removing an attribute. It turns out that we were operating on an inode with lots of delalloc extents, and thus an if_bytes values for the data fork that is larger than biggest possible on-disk storage for it which utterly confuses the code near the end of xfs_attr_shortform_bytesfit. Fix this by always allowing the current attribute fork, like we already do for the attr1 format, given that delalloc conversion will take care for moving either the data or attribute area out of line if it doesn't fit at that point - or making the point moot by merging extents at this point. Also document the function better, and clean up some loose bits. Reviewed-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Ben Myers <bpm@sgi.com> Acked-by:
-
Christoph Hellwig authored
commit 4dd2cb4a upstream. If we are doing synchronous inode reclaim we block the VM from making progress in memory reclaim. So if we encouter a flush locked inode promote it in the delwri list and wake up xfsbufd to write it out now. Without this we can get hangs of up to 30 seconds during workloads hitting synchronous inode reclaim. The scheme is copied from what we do for dquot reclaims. Reported-by:
Simon Kirby <sim@hostway.ca> Signed-off-by:
-
Christoph Hellwig authored
commit fa8b18ed upstream. This prevents in-memory corruption and possible panics if the on-disk ACL is badly corrupted. Signed-off-by:
-
