The RPMH regulator binding covers several devices with different
regulator supplies, so it uses patterns matching broad range of these
supplies.  This works fine but is not specific and might miss actual
mistakes when a wrong supply property is used for given variant.

Describe the supplies depending on the compatible, using a defs-allOf
method.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220426105501.73200-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

David Collins' email bounces ("Recipient address rejected: undeliverable
address: No such user here").
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220426105501.73200-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

When DVS is enabled via the devicetree properties
"nxp,dvs-run-voltage" and "nxp,dvs-standby-voltage" then
also the bit that enables DVS control via PMIC_STBY_REQ pin
should be set.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-5-rickaran@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-4-rickaran@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

Make it possible to do warm reset on WDOG_B assertion.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-3-rickaran@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

Make the I2C Level Translator included in PCA9450 configurable from
devicetree. The reset state is off. By setting nxp,i2c-lt-enable, the
I2C Level Translator will be enabled while in STANDBY or RUN state.
Signed-off-by: Per-Daniel Olsson <perdo@axis.com>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-2-rickaran@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

By setting nxp,i2c-lt-enable the I2C level translator is
enabled.
Signed-off-by: Per-Daniel Olsson <perdo@axis.com>
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Link: https://lore.kernel.org/r/20220429072211.24957-1-rickaran@axis.comSigned-off-by: Mark Brown <broonie@kernel.org>

The correct file name is regulator.yaml, not regulators.yaml.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220429120914.9928-1-markuss.broks@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Regulators block of SM5703 controls several voltage regulators which
are used to power various components. There are 3 LDO outputs ranging
from 1.5 to 3.3V, a buck regulator ranging from 1V to 3V, two fixed
voltage LDO regulators for powering the USB devices and one high-power
fixed voltage LDO line (actually two lines) meant to power high-power
USB devices.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220423085319.483524-6-markuss.broks@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch adds device-tree bindings for regulators on Silicon Mitus
SM5703 MFD.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220423085319.483524-3-markuss.broks@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Having one enable-gpios property for all regulators is discouraged and
instead, similarly to regulator core ena_gpiod feature, each GPIO should
be present in each regulator node.  Add support for parsing such GPIOs,
keeping backwards compatibility.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/20220425072455.27356-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The binding and driver duplicated regulator core feature of controlling
regulators with GPIOs (of_parse_cb + ena_gpiod) and created its own
enable-gpios property with multiple GPIOs.

This is a less preferred way, because enable-gpios should enable only one
element, not multiple. It also duplicates existing solution.

Deprecate the original 'enable-gpios' and add per-regulator property.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220425072455.27356-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

These delays can be relatively large (e.g., hundreds of microseconds to
several milliseconds on RK3399 Gru systems). Per
Documentation/timers/timers-howto.rst, that should usually use a
sleeping delay. Let's use the existing regulator delay helper to handle
both large and small delays appropriately. This avoids burning a bunch
of CPU time and hurting scheduling latencies when hitting regulators a
lot (e.g., during cpufreq).

The sleep vs. delay issue choice has been made differently over time --
early versions of RK3399 Gru PWM-regulator support used usleep_range()
in pwm-regulator.c. More of this got moved into the regulator core,
in commits like:

73e705bf regulator: core: Add set_voltage_time op

At the same time, the sleep turned into a delay.

It's OK to sleep in _regulator_do_set_voltage(), as we aren't in an
atomic context. (All our callers grab various mutexes already.)

I avoid using fsleep() because it uses a usleep_range() of [N to N*2],
and usleep_range() very commonly biases to the high end of the range. We
don't want to double the expected delay, especially for long delays.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220420141511.v2.2.If0fc61a894f537b052ca41572aff098cf8e7e673@changeidSigned-off-by: Mark Brown <broonie@kernel.org>

I want to use it in other contexts besides _regulator_do_enable().
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20220420141511.v2.1.I31ef0014c9597d53722ab513890f839f357fdfb3@changeidSigned-off-by: Mark Brown <broonie@kernel.org>

KASAN report slab-out-of-bounds in __regmap_init as follows:

BUG: KASAN: slab-out-of-bounds in __regmap_init drivers/base/regmap/regmap.c:841
Read of size 1 at addr ffff88803678cdf1 by task xrun/9137

CPU: 0 PID: 9137 Comm: xrun Tainted: G        W         5.18.0-rc2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0xe8/0x15a lib/dump_stack.c:88
 print_report.cold+0xcd/0x69b mm/kasan/report.c:313
 kasan_report+0x8e/0xc0 mm/kasan/report.c:491
 __regmap_init+0x4540/0x4ba0 drivers/base/regmap/regmap.c:841
 __devm_regmap_init+0x7a/0x100 drivers/base/regmap/regmap.c:1266
 __devm_regmap_init_i2c+0x65/0x80 drivers/base/regmap/regmap-i2c.c:394
 da9121_i2c_probe+0x386/0x6d1 drivers/regulator/da9121-regulator.c:1039
 i2c_device_probe+0x959/0xac0 drivers/i2c/i2c-core-base.c:563

This happend when da9121 device is probe by da9121_i2c_id, but with
invalid dts. Thus, chip->subvariant_id is set to -EINVAL, and later
da9121_assign_chip_model() will access 'regmap' without init it.

Fix it by return -EINVAL from da9121_assign_chip_model() if
'chip->subvariant_id' is invalid.

Fixes: f3fbd556 ("regulator: da9121: Add device variants")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Adam Ward <Adam.Ward.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20220421090335.1876149-1-weiyongjun1@huawei.comSigned-off-by: Mark Brown <broonie@kernel.org>

Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220412071030.2532230-1-chi.minghao@zte.com.cnSigned-off-by: Mark Brown <broonie@kernel.org>

Document used PMIC IDs: 'h' (sm8450-hdk, sm8450-qrd) and 'k'
(sc7280-crd).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220411105903.230733-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

This refers common bindings, so this is preferred for
unevaluatedProperties instead of additionalProperties.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1649145303-30221-3-git-send-email-hayashi.kunihiko@socionext.comSigned-off-by: Mark Brown <broonie@kernel.org>

Instead of "oneOf:" choices, use "allOf:" and "if:" to define clocks,
resets, and their names that can be taken by the compatible string.

The order of clock-names and reset-names doesn't change here.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1649145303-30221-2-git-send-email-hayashi.kunihiko@socionext.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from cy_huang <u0084500@gmail.com>:

This patch series add Richtek RT5759 buck converter support.

GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove these assignment all at once.

For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220325184508.45670-1-andriy.shevchenko@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Johnson Wang <johnson.wang@mediatek.com>:

This patchset adds support for MediaTek PMIC MT6366.
MT6366 is the primary PMIC for MT8186 and probably other SOCs.

Merge series from Johnson Wang <johnson.wang@mediatek.com>:

This patchset adds support for MediaTek PMIC MT6366.
MT6366 is the primary PMIC for MT8186 and probably other SOCs.

The MT6366 is a regulator found on boards based on MediaTek MT8186 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Link: https://lore.kernel.org/r/20220401080212.27383-2-johnson.wang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add buck_vcore_sshub and ldo_vsram_others_sshub
regulators to binding document for MT6358 and MT6366.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Link: https://lore.kernel.org/r/20220401080212.27383-3-johnson.wang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

While we currently assume that regulators with no control available are
just uncontionally enabled this isn't always as clearly displayed to
users as is desirable, for example the code for disabling unused
regulators will log that it is about to disable them. Clean this up a
bit by setting always_on during constraint evaluation if we have no
available mechanism for controlling the regualtor so things that check
the constraint will do the right thing.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220325144637.1543496-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

OOMs are very verbose, we don't need to print an additional error message
when we fail to allocate.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220324201854.3107077-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Correct grammar in 'enable-gpios' description and remove useless comment
about regulator nodes, because these are obvious from patternProperties.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220401153711.1057853-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add bindings for Richtek RT5759 high-performance DCDC converter.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1648294788-11758-2-git-send-email-u0084500@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for Richtek RT5759 high-performance DCDC converter.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1648294788-11758-3-git-send-email-u0084500@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add buck_vcore_sshub and ldo_vsram_others_sshub
regulators to binding document for MT6358 and MT6366.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220317030402.24894-3-johnson.wang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

The MT6366 is a regulator found on boards based on MediaTek MT8186 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220317030402.24894-2-johnson.wang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Pull more tracing updates from Steven Rostedt:

 - Rename the staging files to give them some meaning. Just
   stage1,stag2,etc, does not show what they are for

 - Check for NULL from allocation in bootconfig

 - Hold event mutex for dyn_event call in user events

 - Mark user events to broken (to work on the API)

 - Remove eBPF updates from user events

 - Remove user events from uapi header to keep it from being installed.

 - Move ftrace_graph_is_dead() into inline as it is called from hot
   paths and also convert it into a static branch.

* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Move user_events.h temporarily out of include/uapi
  ftrace: Make ftrace_graph_is_dead() a static branch
  tracing: Set user_events to BROKEN
  tracing/user_events: Remove eBPF interfaces
  tracing/user_events: Hold event_mutex during dyn_event_add
  proc: bootconfig: Add null pointer check
  tracing: Rename the staging files for trace_events

Pull clk fix from Stephen Boyd:
 "A single revert to fix a boot regression seen when clk_put() started
  dropping rate range requests. It's best to keep various systems
  booting so we'll kick this out and try again next time"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  Revert "clk: Drop the rate range on clk_put()"

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes and updates:

   - Make the prctl() for enabling dynamic XSTATE components correct so
     it adds the newly requested feature to the permission bitmap
     instead of overwriting it. Add a selftest which validates that.

   - Unroll string MMIO for encrypted SEV guests as the hypervisor
     cannot emulate it.

   - Handle supervisor states correctly in the FPU/XSTATE code so it
     takes the feature set of the fpstate buffer into account. The
     feature sets can differ between host and guest buffers. Guest
     buffers do not contain supervisor states. So far this was not an
     issue, but with enabling PASID it needs to be handled in the buffer
     offset calculation and in the permission bitmaps.

   - Avoid a gazillion of repeated CPUID invocations in by caching the
     values early in the FPU/XSTATE code.

   - Enable CONFIG_WERROR in x86 defconfig.

   - Make the X86 defconfigs more useful by adapting them to Y2022
     reality"

* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu/xstate: Consolidate size calculations
  x86/fpu/xstate: Handle supervisor states in XSTATE permissions
  x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
  x86/fpu: Cache xfeature flags from CPUID
  x86/fpu/xsave: Initialize offset/size cache early
  x86/fpu: Remove unused supervisor only offsets
  x86/fpu: Remove redundant XCOMP_BV initialization
  x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
  x86/config: Make the x86 defconfigs a bit more usable
  x86/defconfig: Enable WERROR
  selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
  x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation

Pull RT signal fix from Thomas Gleixner:
 "Revert the RT related signal changes. They need to be reworked and
  generalized"

* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"

Pull more dma-mapping updates from Christoph Hellwig:

 - fix a regression in dma remap handling vs AMD memory encryption (me)

 - finally kill off the legacy PCI DMA API (Christophe JAILLET)

* tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: move pgprot_decrypted out of dma_pgprot
  PCI/doc: cleanup references to the legacy PCI DMA API
  PCI: Remove the deprecated "pci-dma-compat.h" API

Pull ARM fixes from Russell King:

 - avoid unnecessary rebuilds for library objects

 - fix return value of __setup handlers

 - fix invalid input check for "crashkernel=" kernel option

 - silence KASAN warnings in unwind_frame

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
  ARM: 9190/1: kdump: add invalid input check for 'crashkernel=0'
  ARM: 9187/1: JIVE: fix return value of __setup handler
  ARM: 9189/1: decompressor: fix unneeded rebuilds of library objects

This reverts commit 7dabfa2b. There are
multiple reports that this breaks boot on various systems. The common
theme is that orphan clks are having rates set on them when that isn't
expected. Let's revert it out for now so that -rc1 boots.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org