- 08 Jun, 2016 40 commits
-
-
Tomáš Trnka authored
commit c0cb8bf3 upstream. The length of the GSS MIC token need not be a multiple of four bytes. It is then padded by XDR to a multiple of 4 B, but unwrap_integ_data() would previously only trim mic.len + 4 B. The remaining up to three bytes would then trigger a check in nfs4svc_decode_compoundargs(), leading to a "garbage args" error and mount failure: nfs4svc_decode_compoundargs: compound not properly padded! nfsd: failed to decode arguments! This would prevent older clients using the pre-RFC 4121 MIC format (37-byte MIC including a 9-byte OID) from mounting exports from v3.9+ servers using krb5i. The trimming was introduced by commit 4c190e2f ("sunrpc: trim off trailing checksum before returning decrypted or integrity authenticated buffer"). Fixes: 4c190e2f "unrpc: trim off trailing checksum..." Signed-off-by:
Tomáš Trnka <ttrnka@mail.muni.cz> Acked-by:
Jeff Layton <jlayton@poochiereds.net> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Juergen Gross authored
commit dd14be92 upstream. Instead of having two functions for cycling through the E820 map in order to count to be remapped pages and remap them later, just use one function with a caller supplied sub-function called for each region to be processed. This eliminates the possibility of a mismatch between both loops which showed up in certain configurations. Suggested-by:
Ed Swierk <eswierk@skyportsystems.com> Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Ross Lagerwall authored
commit f0f39387 upstream. Commit ff1e22e7 ("xen/events: Mask a moving irq") open-coded irq_move_irq() but left out checking if the IRQ is disabled. This broke resuming from suspend since it tries to move a (disabled) irq without holding the IRQ's desc->lock. Fix it by adding in a check for disabled IRQs. The resulting stacktrace was: kernel BUG at /build/linux-UbQGH5/linux-4.4.0/kernel/irq/migration.c:31! invalid opcode: 0000 [#1] SMP Modules linked in: xenfs xen_privcmd ... CPU: 0 PID: 9 Comm: migration/0 Not tainted 4.4.0-22-generic #39-Ubuntu Hardware name: Xen HVM domU, BIOS 4.6.1-xs125180 05/04/2016 task: ffff88003d75ee00 ti: ffff88003d7bc000 task.ti: ffff88003d7bc000 RIP: 0010:[<ffffffff810e26e2>] [<ffffffff810e26e2>] irq_move_masked_irq+0xd2/0xe0 RSP: 0018:ffff88003d7bfc50 EFLAGS: 00010046 RAX: 0000000000000000 RBX: ffff88003d40ba00 RCX: 0000000000000001 RDX: 0000000000000001 RSI: 0000000000000100 RDI: ffff88003d40bad8 RBP: ffff88003d7bfc68 R08: 0000000000000000 R09: ffff88003d000000 R10: 0000000000000000 R11: 000000000000023c R12: ffff88003d40bad0 R13: ffffffff81f3a4a0 R14: 0000000000000010 R15: 00000000ffffffff FS: 0000000000000000(0000) GS:ffff88003da00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007fd4264de624 CR3: 0000000037922000 CR4: 00000000003406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Stack: ffff88003d40ba38 0000000000000024 0000000000000000 ffff88003d7bfca0 ffffffff814c8d92 00000010813ef89d 00000000805ea732 0000000000000009 0000000000000024 ffff88003cc39b80 ffff88003d7bfce0 ffffffff814c8f66 Call Trace: [<ffffffff814c8d92>] eoi_pirq+0xb2/0xf0 [<ffffffff814c8f66>] __startup_pirq+0xe6/0x150 [<ffffffff814ca659>] xen_irq_resume+0x319/0x360 [<ffffffff814c7e75>] xen_suspend+0xb5/0x180 [<ffffffff81120155>] multi_cpu_stop+0xb5/0xe0 [<ffffffff811200a0>] ? cpu_stop_queue_work+0x80/0x80 [<ffffffff811203d0>] cpu_stopper_thread+0xb0/0x140 [<ffffffff810a94e6>] ? finish_task_switch+0x76/0x220 [<ffffffff810ca731>] ? __raw_callee_save___pv_queued_spin_unlock+0x11/0x20 [<ffffffff810a3935>] smpboot_thread_fn+0x105/0x160 [<ffffffff810a3830>] ? sort_range+0x30/0x30 [<ffffffff810a0588>] kthread+0xd8/0xf0 [<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0 [<ffffffff8182568f>] ret_from_fork+0x3f/0x70 [<ffffffff810a04b0>] ? kthread_create_on_node+0x1e0/0x1e0 Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
-
Gavin Shan authored
commit 5a0cdbfd upstream. The function eeh_pe_reset_and_recover() is used to recover EEH error when the passthrou device are transferred to guest and backwards. The content in the device's config space will be lost on PE reset issued in the middle of the recovery. The function saves/restores it before/after the reset. However, config access to some adapters like Broadcom BCM5719 at this point will causes fenced PHB. The config space is always blocked and we save 0xFF's that are restored at late point. The memory BARs are totally corrupted, causing another EEH error upon access to one of the memory BARs. This restores the config space on those adapters like BCM5719 from the content saved to the EEH device when it's populated, to resolve above issue. Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices") Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by:
Russell Currey <ruscur@russell.cc> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Guilherme G. Piccoli authored
commit c2078d9e upstream. This reverts commit 89a51df5. The function eeh_add_device_early() is used to perform EEH initialization in devices added later on the system, like in hotplug/DLPAR scenarios. Since the commit 89a51df5 ("powerpc/eeh: Fix crash in eeh_add_device_early() on Cell") a new check was introduced in this function - Cell has no EEH capabilities which led to kernel oops if hotplug was performed, so checking for eeh_enabled() was introduced to avoid the issue. However, in architectures that EEH is present like pSeries or PowerNV, we might reach a case in which no PCI devices are present on boot time and so EEH is not initialized. Then, if a device is added via DLPAR for example, eeh_add_device_early() fails because eeh_enabled() is false, and EEH end up not being enabled at all. This reverts the aforementioned patch since a new verification was introduced by the commit d91dafc0 ("powerpc/eeh: Delay probing EEH device during hotplug") and so the original Cell issue does not happen anymore. Reviewed-by:
Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by:
-
Gavin Shan authored
commit affeb0f2 upstream. The function eeh_pe_reset_and_recover() is used to recover EEH error when the passthrough device are transferred to guest and backwards, meaning the device's driver is vfio-pci or none. When the driver is vfio-pci that provides error_detected() error handler only, the handler simply stops the guest and it's not expected behaviour. On the other hand, no error handlers will be called if we don't have a bound driver. This ignores the error handler in eeh_pe_reset_and_recover() that reports the error to device driver to avoid the exceptional behaviour. Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices") Signed-off-by:
-
Hari Bathini authored
commit 8ed8ab40 upstream. Some of the interrupt vectors on 64-bit POWER server processors are only 32 bytes long (8 instructions), which is not enough for the full first-level interrupt handler. For these we need to branch to an out-of-line (OOL) handler. But when we are running a relocatable kernel, interrupt vectors till __end_interrupts marker are copied down to real address 0x100. So, branching to labels (ie. OOL handlers) outside this section must be handled differently (see LOAD_HANDLER()), considering relocatable kernel, which would need at least 4 instructions. However, branching from interrupt vector means that we corrupt the CFAR (come-from address register) on POWER7 and later processors as mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions) that contains the part up to the point where the CFAR is saved in the PACA should be part of the short interrupt vectors before we branch out to OOL handlers. But as mentioned already, there are interrupt vectors on 64-bit POWER server processors that are only 32 bytes long (like vectors 0x4f00, 0x4f20, etc.), which cannot accomodate the above two cases at the same time owing to space constraint. Currently, in these interrupt vectors, we simply branch out to OOL handlers, without using LOAD_HANDLER(), which leaves us vulnerable when running a relocatable kernel (eg. kdump case). While this has been the case for sometime now and kdump is used widely, we were fortunate not to see any problems so far, for three reasons: 1. In almost all cases, production kernel (relocatable) is used for kdump as well, which would mean that crashed kernel's OOL handler would be at the same place where we end up branching to, from short interrupt vector of kdump kernel. 2. Also, OOL handler was unlikely the reason for crash in almost all the kdump scenarios, which meant we had a sane OOL handler from crashed kernel that we branched to. 3. On most 64-bit POWER server processors, page size is large enough that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel, that sits right below interrupt vector code from kdump kernel, as executable as well. Let us fix this by moving the __end_interrupts marker down past OOL handlers to make sure that we also copy OOL handlers to real address 0x100 when running a relocatable kernel. This fix has been tested successfully in kdump scenario, on an LPAR with 4K page size by using different default/production kernel and kdump kernel. Also tested by manually corrupting the OOL handlers in the first kernel and then kdump'ing, and then causing the OOL handlers to fire - mpe. Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers") Signed-off-by:
Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
-
Sven Eckelmann authored
The router is put down twice when it was non-NULL and either orig_ifinfo is NULL afterwards or batman-adv receives a packet with the same sequence number. This will end up in a use-after-free when the batadv_neigh_node is removed because the reference counter ended up too early at 0. This patch is skipping netdev and is being sent directly to stable in accordance with David S. Miller[1]. The reason is that this patch applies only on linux-4.6 and not on linux-4.7/net because it was "accidentally" fixed by a refactoring commit (more details in [2]). It addresses a reference imbalance which systematically leads to a use-after-free and then a kernel crash. [1] https://www.mail-archive.com/b.a.t.m.a.n@lists.open-mesh.org/msg15258.html [2] https://www.mail-archive.com/b.a.t.m.a.n@lists.open-mesh.org/msg15252.html Fixes: 9323158e ("batman-adv: OGMv2 - implement originators logic") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Antonio Quartulli <a@unstable.cc> Signed-off-by:
-
Zhao Qiang authored
commit 11ca2b7a upstream. New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart. So add it. Signed-off-by:
Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by:
-
Oleg Nesterov authored
commit bf959931 upstream. The following program (simplified version of generated by syzkaller) #include <pthread.h> #include <unistd.h> #include <sys/ptrace.h> #include <stdio.h> #include <signal.h> void *thread_func(void *arg) { ptrace(PTRACE_TRACEME, 0,0,0); return 0; } int main(void) { pthread_t thread; if (fork()) return 0; while (getppid() != 1) ; pthread_create(&thread, NULL, thread_func, NULL); pthread_join(thread, NULL); return 0; } creates an unreapable zombie if /sbin/init doesn't use __WALL. This is not a kernel bug, at least in a sense that everything works as expected: debugger should reap a traced sub-thread before it can reap the leader, but without __WALL/__WCLONE do_wait() ignores sub-threads. Unfortunately, it seems that /sbin/init in most (all?) distributions doesn't use it and we have to change the kernel to avoid the problem. Note also that most init's use sys_waitid() which doesn't allow __WALL, so the necessary user-space fix is not that trivial. This patch just adds the "ptrace" check into eligible_child(). To some degree this matches the "tsk->ptrace" in exit_notify(), ->exit_signal is mostly ignored when the tracee reports to debugger. Or WSTOPPED, the tracer doesn't need to set this flag to wait for the stopped tracee. This obviously means the user-visible change: __WCLONE and __WALL no longer have any meaning for debugger. And I can only hope that this won't break something, but at least strace/gdb won't suffer. We could make a more conservative change. Say, we can take __WCLONE into account, or !thread_group_leader(). But it would be nice to not complicate these historical/confusing checks. Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Jan Kratochvil <jan.kratochvil@redhat.com> Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com> Cc: Pedro Alves <palves@redhat.com> Cc: Roland McGrath <roland@hack.frob.com> Cc: <syzkaller@googlegroups.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Chen Feng authored
commit 6cd9dc3e upstream. While testing the kcompactd in my platform 3G MEM only DMA ZONE. I found the kcompactd never wakeup. It seems the zoneindex has already minus 1 before. So the traverse here should be <=. It fixes a regression where kswapd could previously compact, but kcompactd not. Not a crash fix though. [akpm@linux-foundation.org: fix kcompactd_do_work() as well, per Hugh] Link: http://lkml.kernel.org/r/1463659121-84124-1-git-send-email-puck.chen@hisilicon.com Fixes: accf6242 ("mm, kswapd: replace kswapd compaction with waking up kcompactd") Signed-off-by:
Chen Feng <puck.chen@hisilicon.com> Acked-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: Zhuangluan Su <suzhuangluan@hisilicon.com> Cc: Yiping Xu <xuyiping@hisilicon.com> Signed-off-by:
-
Stefan Bader authored
commit 4b50bcc7 upstream. Since commit 92923ca3 ("mm: meminit: only set page reserved in the memblock region") the reserved bit is set on reserved memblock regions. However start and end address are passed as unsigned long. This is only 32bit on i386, so it can end up marking the wrong pages reserved for ranges at 4GB and above. This was observed on a 32bit Xen dom0 which was booted with initial memory set to a value below 4G but allowing to balloon in memory (dom0_mem=1024M for example). This would define a reserved bootmem region for the additional memory (for example on a 8GB system there was a reverved region covering the 4GB-8GB range). But since the addresses were passed on as unsigned long, this was actually marking all pages from 0 to 4GB as reserved. Fixes: 92923ca3 ("mm: meminit: only set page reserved in the memblock region") Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.comSigned-off-by:
Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
-
Colin Ian King authored
commit 06af9b0f upstream. The OID_sha224 case is missing a break and it falls through to the -ENOPKG error default. Since HASH_ALGO_SHA224 seems to be supported, this looks like an unintentional missing break. Fixes: 07f081fb ("PKCS#7: Add OIDs for sha224, sha284 and sha512 hash algos and use them") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Tiffany Lin authored
commit baf43c6e upstream. In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved filed of v4l2_create_buffers filled with zero Reserved field is filled with zero in v4l_create_bufs. This patch copy reserved field of v4l2_create_buffer from kernel space to user space Signed-off-by:
Tiffany Lin <tiffany.lin@mediatek.com> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Prarit Bhargava authored
commit ad67b437 upstream. b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with the PCI spec. But it didn't do anything for expansion ROM BARs, so we still try to size them, resulting in warnings like this on Broadwell-EP: pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref] Move the non-compliant BAR check from __pci_read_base() up to pci_read_bases() so it applies to the expansion ROM BAR as well as to BARs 0-5. Note that direct callers of __pci_read_base(), like sriov_init(), will now bypass this check. We haven't had reports of devices with broken SR-IOV BARs yet. [bhelgaas: changelog] Fixes: b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: "H. Peter Anvin" <hpa@zytor.com> CC: Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Andrew Jeffery authored
commit 71324fdc upstream. The range is registered into a linked list which can be referenced throughout the lifetime of the driver. Ensure the range's memory is useful for the same lifetime by adding it to the driver's private data structure. The bug was introduced in the driver's initial commit, which was present in v3.10. Fixes: f0b9a7e5 ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC") Signed-off-by:
Andrew Jeffery <andrew@aj.id.au> Acked-by:
Tomasz Figa <tomasz.figa@gmail.com> Reviewed-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Martin Sperl authored
commit 959ca92a upstream. The current driver calculates the clock divider with fractional support enabled. But it does not enable fractional support in the control register itself resulting in an integer only divider, but in clk_set_rate responds back the fractionally divided clock frequency. This patch enables fractional support in the control register whenever there is a fractional bit set in the requested clock divider. Mash clock limits are are also handled for the PWM clock applying the correct divider limits (2 and max_int) applicable to basic fractional divider support (mash order of 1). It also adds locking to protect the read/modify/write cycle of the register modification. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by:
Martin Sperl <kernel@martin.sperl.org> Signed-off-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
-
Martin Sperl authored
commit 997f16bd upstream. Current clamping of a normal divider allows a value < 1 to be valid. A divider of < 1 would actually only be possible if we had a PLL... So this patch clamps the divider to 1. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by:
-
Martin Sperl authored
commit 6727f086 upstream. bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control register, which may lose the other bits that are currently set by the clock dividers. It also now locks during the read/modify/write cycle of both registers. Fixes: 41691b88 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by:
-
Vladimir Zapolskiy authored
commit cb0ceaf7 upstream. The clk_register() function returns a valid pointer to struct clk or ERR_PTR() error code, this makes a check for returned NULL value useless and may lead to oops on error path. Signed-off-by:
Vladimir Zapolskiy <vz@mleia.com> Acked-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: bcc5fd49 ("clk: at91: add a driver for the h32mx clock") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Eric Anholt authored
commit e708b383 upstream. In poweroff, we set the reset bit and the power down bit, but only managed to unset the reset bit for poweron. This meant that if HDMI did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the PLLH (that had been on at boot time) and never recover. Signed-off-by:
-
Daniel Lezcano authored
commit e7387da5 upstream. Commit 0b89e9aa (cpuidle: delay enabling interrupts until all coupled CPUs leave idle) rightfully fixed a regression by letting the coupled idle state framework to handle local interrupt enabling when the CPU is exiting an idle state. The current code checks if the idle state is coupled and, if so, it will let the coupled code to enable interrupts. This way, it can decrement the ready-count before handling the interrupt. This mechanism prevents the other CPUs from waiting for a CPU which is handling interrupts. But the check is done against the state index returned by the back end driver's ->enter functions which could be different from the initial index passed as parameter to the cpuidle_enter_state() function. entered_state = target_state->enter(dev, drv, index); [ ... ] if (!cpuidle_state_is_coupled(drv, entered_state)) local_irq_enable(); [ ... ] If the 'index' is referring to a coupled idle state but the 'entered_state' is *not* coupled, then the interrupts are enabled again. All CPUs blocked on the sync barrier may busy loop longer if the CPU has interrupts to handle before decrementing the ready-count. That's consuming more energy than saving. Fixes: 0b89e9aa (cpuidle: delay enabling interrupts until all coupled CPUs leave idle) Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> [ rjw: Subject & changelog ] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dave Gerlach authored
commit c998c078 upstream. Currently the 'registered' member of the cpuidle_device struct is set to 1 during cpuidle_register_device. In this same function there are checks to see if the device is already registered to prevent duplicate calls to register the device, but this value is never set to 0 even on unregister of the device. Because of this, any attempt to call cpuidle_register_device after a call to cpuidle_unregister_device will fail which shouldn't be the case. To prevent this, set registered to 0 when the device is unregistered. Fixes: c878a52d (cpuidle: Check if device is already registered) Signed-off-by:
Dave Gerlach <d-gerlach@ti.com> Acked-by:
-
Ulf Hansson authored
commit 0ae3aeef upstream. As pm_runtime_set_active() may fail because the device's parent isn't active, we can end up executing the ->runtime_resume() callback for the device when it isn't allowed. Fix this by invoking pm_runtime_set_active() before running the callback and let's also deal with the error code. Fixes: 37f20416 (PM: Add pm_runtime_suspend|resume_force functions) Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by:
-
Ville Syrjälä authored
commit 36e6d081 upstream. GPIO lookup tables are supposed to be zero terminated. Let's do that and avoid accidentally walking off the end. Fixes: 61dd2ca2 ("mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal") Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by:
Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Heikki Krogerus authored
commit 41a3da2b upstream. All configurations are lost and the registers will have default values when the hardware is suspended and resumed, so saving the private register space context on suspend, and restoring it on resume. Fixes: 4b45efe8 (mfd: Add support for Intel Sunrisepoint LPSS devices) Signed-off-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
-
Andy Shevchenko authored
commit 7f0c5ae1 upstream. There is a potential resource leak in case when ->probe() fails. We have to unregister and remove clock tree which is done here. This is a follow up to previously pushed commit c4726abc ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") that prevents double free() when clkdev_drop() followed by kfree() in devm_kcalloc() release stage. I leave Fixes tag here, but the backporting will require to backport the commit c4726abc ("mfd: intel_quark_i2c_gpio: Use clkdev_create()") first. Fixes: 60ae5b9f (mfd: intel_quark_i2c_gpio: Add Intel Quark X1000 I2C-GPIO MFD Driver) Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
-
Akshay Bhat authored
commit 7a18afe8 upstream. On ads7828 the internal reference defaults to off upon power up. When using internal reference, it needs to be turned on and the voltage needs to settle before normal conversion cycle can be started. Hence perform a dummy read in the probe to enable the internal reference allowing the voltage to settle before performing a normal read. Without this fix, the first read from the ADC when using internal reference always returns incorrect data. Signed-off-by:
Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Javier Martinez Canillas authored
commit 5e3ca2b3 upstream. Commit 6261b06d ("regulator: Defer lookup of supply to regulator_get") moved the regulator supplies lookup logic from the regulators registration to the regulators get time. Unfortunately, that changed the behavior of the regulator core since now a parent supply with a child regulator marked as always-on, won't be enabled unless a client driver attempts to get the child regulator during boot. This patch tries to resolve the parent supply for the already registered regulators each time that a new regulator is registered. So the regulators that have child regulators marked as always on will be enabled regardless if a driver gets the child regulator or not. That was the behavior before the mentioned commit, since parent supplies were looked up at regulator registration time instead of during child get. Since regulator_resolve_supply() checks for rdev->supply, most of the times it will be a no-op. Errors aren't checked to keep the possible out of order dependencies which was the motivation for the mentioned commit. Also, the supply being available will be enforced on regulator get anyways in case the resolve fails on regulators registration. Fixes: 6261b06d ("regulator: Defer lookup of supply to regulator_get") Suggested-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 78cbccd3 upstream. When KDUMP is triggered the driver first talks to the firmware in INTX mode, but the adapter firmware is still in MSIX mode. Therefore the first driver command hangs since the driver is waiting for an INTX response and firmware gives a MSIX response. If when the OS is installed on a RAID drive created by the adapter KDUMP will hang since the driver does not receive a response in sync mode. Fixed by: Change the firmware to INTX mode if it is in MSIX mode before sending the first sync command. Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit fc4bf75e upstream. Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 07beca2b upstream. aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 116d77fe upstream. The adapter has to be started after updating the number of MSIX Vectors Fixes: ecc479e0 (aacraid: Set correct MSIX count for EEH recovery) Signed-off-by:
-
Martin K. Petersen authored
commit d65c8fff upstream. This reverts commit 9be32181 which caused a regression on hardware using the SLI3 interface. Reported-by:
Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by:
James Bottomley <jejb@linux.vnet.ibm.com> Signed-off-by:
-
wang yanqing authored
commit cf968937 upstream. We can't use kfree_skb in irq disable context, because spin_lock_irqsave make sure we are always in irq disable context, use dev_kfree_skb_irq instead of kfree_skb is better than dev_kfree_skb_any. This patch fix below kernel warning: [ 7612.095528] ------------[ cut here ]------------ [ 7612.095546] WARNING: CPU: 3 PID: 4460 at kernel/softirq.c:150 __local_bh_enable_ip+0x58/0x80() [ 7612.095550] Modules linked in: rtl8723be x86_pkg_temp_thermal btcoexist rtl_pci rtlwifi rtl8723_common [ 7612.095567] CPU: 3 PID: 4460 Comm: ifconfig Tainted: G W 4.4.0+ #4 [ 7612.095570] Hardware name: LENOVO 20DFA04FCD/20DFA04FCD, BIOS J5ET48WW (1.19 ) 08/27/2015 [ 7612.095574] 00000000 00000000 da37fc70 c12ce7c5 00000000 da37fca0 c104cc59 c19d4454 [ 7612.095584] 00000003 0000116c c19d4784 00000096 c10508a8 c10508a8 00000200 c1b42400 [ 7612.095594] f29be780 da37fcb0 c104ccad 00000009 00000000 da37fcbc c10508a8 f21f08b8 [ 7612.095604] Call Trace: [ 7612.095614] [<c12ce7c5>] dump_stack+0x41/0x5c [ 7612.095620] [<c104cc59>] warn_slowpath_common+0x89/0xc0 [ 7612.095628] [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80 [ 7612.095634] [<c10508a8>] ? __local_bh_enable_ip+0x58/0x80 [ 7612.095640] [<c104ccad>] warn_slowpath_null+0x1d/0x20 [ 7612.095646] [<c10508a8>] __local_bh_enable_ip+0x58/0x80 [ 7612.095653] [<c16b7d34>] destroy_conntrack+0x64/0xa0 [ 7612.095660] [<c16b300f>] nf_conntrack_destroy+0xf/0x20 [ 7612.095665] [<c1677565>] skb_release_head_state+0x55/0xa0 [ 7612.095670] [<c16775bb>] skb_release_all+0xb/0x20 [ 7612.095674] [<c167760b>] __kfree_skb+0xb/0x60 [ 7612.095679] [<c16776f0>] kfree_skb+0x30/0x70 [ 7612.095686] [<f81b869d>] ? rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci] [ 7612.095692] [<f81b869d>] rtl_pci_reset_trx_ring+0x22d/0x370 [rtl_pci] [ 7612.095698] [<f81b87f9>] rtl_pci_start+0x19/0x190 [rtl_pci] [ 7612.095705] [<f81970e6>] rtl_op_start+0x56/0x90 [rtlwifi] [ 7612.095712] [<c17e3f16>] drv_start+0x36/0xc0 [ 7612.095717] [<c17f5ab3>] ieee80211_do_open+0x2d3/0x890 [ 7612.095725] [<c16820fe>] ? call_netdevice_notifiers_info+0x2e/0x60 [ 7612.095730] [<c17f60bd>] ieee80211_open+0x4d/0x50 [ 7612.095736] [<c16891b3>] __dev_open+0xa3/0x130 [ 7612.095742] [<c183fa53>] ? _raw_spin_unlock_bh+0x13/0x20 [ 7612.095748] [<c1689499>] __dev_change_flags+0x89/0x140 [ 7612.095753] [<c127c70d>] ? selinux_capable+0xd/0x10 [ 7612.095759] [<c1689589>] dev_change_flags+0x29/0x60 [ 7612.095765] [<c1700b93>] devinet_ioctl+0x553/0x670 [ 7612.095772] [<c12db758>] ? _copy_to_user+0x28/0x40 [ 7612.095777] [<c17018b5>] inet_ioctl+0x85/0xb0 [ 7612.095783] [<c166e647>] sock_ioctl+0x67/0x260 [ 7612.095788] [<c166e5e0>] ? sock_fasync+0x80/0x80 [ 7612.095795] [<c115c99b>] do_vfs_ioctl+0x6b/0x550 [ 7612.095800] [<c127c812>] ? selinux_file_ioctl+0x102/0x1e0 [ 7612.095807] [<c10a8914>] ? timekeeping_suspend+0x294/0x320 [ 7612.095813] [<c10a256a>] ? __hrtimer_run_queues+0x14a/0x210 [ 7612.095820] [<c1276e24>] ? security_file_ioctl+0x34/0x50 [ 7612.095827] [<c115cef0>] SyS_ioctl+0x70/0x80 [ 7612.095832] [<c1001804>] do_fast_syscall_32+0x84/0x120 [ 7612.095839] [<c183ff91>] sysenter_past_esp+0x36/0x55 [ 7612.095844] ---[ end trace 97e9c637a20e8348 ]--- Signed-off-by:
Wang YanQing <udknight@gmail.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
wang yanqing authored
commit 873ffe15 upstream. In commit a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), the tests for enter/exit power-save mode were inverted. With this change applied, the wifi connection becomes much more stable. Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Signed-off-by:
-
Larry Finger authored
commit baa17022 upstream. The previous patch added an option to rtl8723be to manually select the antenna for those cases when only a single antenna is present, and the on-board EEPROM is incorrectly programmed. This patch implements the necessary changes in the Bluetooth coexistence driver. Signed-off-by:
-
Larry Finger authored
commit c18d8f50 upstream. A number of new laptops have been delivered with only a single antenna. In principle, this is OK; however, a problem arises when the on-board EEPROM is programmed to use the other antenna connection. The option of opening the computer and moving the connector is not always possible as it will void the warranty in some cases. In addition, this solution breaks the Windows driver when the box dual boots Linux and Windows. A fix involving a new module parameter has been developed. This commit adds the new parameter and implements the changes needed for the driver. Signed-off-by:
-
Krzysztof Kozlowski authored
commit f1925d78 upstream. In case of timeout during read operation, the exit path lacked PM runtime put. This could lead to unbalanced runtime PM usage counter thus leaving the device in an active state. Fixes: d7fd6075 ("hwrng: exynos - Add timeout for waiting on init done") Signed-off-by:
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
