interval displays the probability and vice versa.

Fixes: 6adc4a22 ("fault-inject: add ratelimit option")
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When the kernel compiled with KASAN=y, GCC adds redzones for each
variable on stack.  This enlarges function's stack frame and causes:

	'warning: the frame size of X bytes is larger than Y bytes'

The worst case I've seen for now is following:

   ../net/wireless/nl80211.c: In function `nl80211_send_wiphy':
   ../net/wireless/nl80211.c:1731:1: warning: the frame size of 5448 bytes is larger than 2048 bytes [-Wframe-larger-than=]

That kind of warning becomes useless with KASAN=y.  It doesn't
necessarily indicate that there is some problem in the code, thus we
should turn it off.

(The KASAN=y stack size in increased from 16k to 32k for this reason)
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Abylay Ospan <aospan@netup.ru>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Currently a simple program below issues a sendfile(2) system call which
takes about 62 days to complete in my test KVM instance.

        int fd;
        off_t off = 0;

        fd = open("file", O_RDWR | O_TRUNC | O_SYNC | O_CREAT, 0644);
        ftruncate(fd, 2);
        lseek(fd, 0, SEEK_END);
        sendfile(fd, fd, &off, 0xfffffff);

Now you should not ask kernel to do a stupid stuff like copying 256MB in
2-byte chunks and call fsync(2) after each chunk but if you do, sysadmin
should have a way to stop you.

We actually do have a check for fatal_signal_pending() in
generic_perform_write() which triggers in this path however because we
always succeed in writing something before the check is done, we return
value > 0 from generic_perform_write() and thus the information about
signal gets lost.

Fix the problem by doing the signal check before writing anything.  That
way generic_perform_write() returns -EINTR, the error gets propagated up
and the sendfile loop terminates early.
Signed-off-by: Jan Kara <jack@suse.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Use is_zero_pfn() on pteval only after pte_present() check on pteval
(It might be better idea to introduce is_zero_pte() which checks
pte_present() first).

Otherwise when working on a swap or migration entry and if pte_pfn's
result is equal to zero_pfn by chance, we lose user's data in
__collapse_huge_page_copy().  So if you're unlucky, the application
segfaults and finally you could see below message on exit:

BUG: Bad rss-counter state mm:ffff88007f099300 idx:2 val:3

Fixes: ca0984ca ("mm: incorporate zero pages into transparent huge pages")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>	[4.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The get_maintainer script still reports my old Collabora email based on
old commits but that address no longer exist so update mailmap to report
my current email and avoid people sending to the old address.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Nominate myself as a zsmalloc reviewer.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This was found during userspace fuzzing test when a large size dma cma
allocation is made by driver(like ion) through userspace.

  show_stack+0x10/0x1c
  dump_stack+0x74/0xc8
  kasan_report_error+0x2b0/0x408
  kasan_report+0x34/0x40
  __asan_storeN+0x15c/0x168
  memset+0x20/0x44
  __dma_alloc_coherent+0x114/0x18c
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

call_usermodehelper_exec_sync() does fork() + wait() with "unignored"
SIGCHLD.  What we have missed is that this worker thread can have other
children previously forked by call_usermodehelper_exec_work() without
UMH_WAIT_PROC.  If such a child exits in between it becomes a zombie
because auto-reaping only works if SIGCHLD is ignored, and nobody can
reap it (unless/until this worker thread exits too).

Change the !UMH_WAIT_PROC case to use CLONE_PARENT.

Note: this is only first step.  All PF_KTHREAD tasks, even created by
kernel_thread() should have ->parent == kthreadd by default.

Fixes: bb304a5c ("kmod: handle UMH_WAIT_PROC from system unbound workqueue")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull intel-iommu bugfix from David Woodhouse:
 "This contains a single fix, for when the IOMMU API is used to overlay
  an existing mapping comprised of 4KiB pages, with a mapping that can
  use superpages.

  For the *first* superpage in the new mapping, we were correctly¹
  freeing the old bottom-level page table page and clearing the link to
  it, before installing the superpage.  For subsequent superpages,
  however, we weren't.  This causes a memory leak, and a warning about
  setting a PTE which is already set.

  ¹ Well, not *entirely* correctly.  We just free the page table pages
    right there and then, which is wrong.  In fact they should only be
    freed *after* the IOTLB is flushed so we know the hardware will no
    longer be looking at them....  and in fact I note that the IOTLB
    flush is completely missing from the intel_iommu_map() code path,
    although it needs to be there if it's permitted to overwrite
    existing mappings.

    Fixing those is somewhat more intrusive though, and will probably
    need to wait for 4.4 at this point"

* tag 'for-linus-20151021' of git://git.infradead.org/intel-iommu:
  iommu/vt-d: fix range computation when making room for large pages

Pull MMC bugfix from Ulf Hansson:
 "Here's yet another MMC fix intended for v4.3 rc7.  I don't expect to
  send any further pull requests for 4.3 rc[n].

  MMC core:
   - Don't re-tune in the reset sequence to allow re-init of the card"

* tag 'mmc-v4.3-rc5' of git://git.linaro.org/people/ulf.hansson/mmc:
  mmc: core: Fix init_card in 52Mhz

Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull UML fixes from Richard Weinberger:
 "This contains four overdue UML regression fixes"

* 'for-linus-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: Fix kernel mode fault condition
  um: Fix waitpid() usage in helper code
  um: Do not rely on libc to provide modify_ldt()
  um: Fix out-of-tree build

Pull key handling fixes from David Howells:
 "Here are two patches, the first of which at least should go upstream
  immediately:

  (1) Prevent a user-triggerable crash in the keyrings destructor when a
      negatively instantiated keyring is garbage collected.  I have also
      seen this triggered for user type keys.

  (2) Prevent the user from using requesting that a keyring be created
      and instantiated through an upcall.  Doing so is probably safe
      since the keyring type ignores the arguments to its instantiation
      function - but we probably shouldn't let keyrings be created in
      this manner"

* 'keys-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  KEYS: Don't permit request_key() to construct a new keyring
  KEYS: Fix crash when attempt to garbage collect an uninstantiated keyring

We have to exclude memory locations <= PAGE_SIZE from
the condition and let the kernel mode fault path catch it.
Otherwise a kernel NULL pointer exception will be reported
as a kernel user space access.

Fixes: d2313084 (um: Catch unprotected user memory access)
Signed-off-by: Richard Weinberger <richard@nod.at>

If UML is executing a helper program it is using
waitpid() with the __WCLONE flag to wait for the program
as the helper is executed from a clone()'ed thread.
While using __WCLONE is perfectly fine for clone()'ed
childs it won't detect terminated childs if the helper
has issued an execve().

We have to use __WALL to wait for both clone()'ed and
regular childs to detect the termination before and
after an execve().
Reported-and-tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>

modify_ldt() was declared as an external symbol. Despite the man
page for this syscall telling that there is no wrapper in glibc,
since version 2.1 there actually is, so linking to the glibc
works.

Since modify_ldt() is not a POSIX interface, other libc
implementations do not always provide a wrapper function.
Even glibc headers do not provide a corresponding declaration.

So go the recommended way to call this using syscall().
Signed-off-by: Hans-Werner Hilse <hwhilse@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>

Commit 30b11ee9 (um: Remove copy&paste code from init.h)
uncovered an issue wrt. out-of-tree builds.
For out-of-tree builds, we must not rely on relative paths.
Before 30b11ee9 it worked by chance as no host code included
generated header files.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>

Pull networking fixes from David Miller:

 1) Account for extra headroom in ath9k driver, from Felix Fietkau.

 2) Fix OOPS in pppoe driver due to incorrect socket state transition,
    from Guillaume Nault.

 3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.

 4) Power management fixes for iwlwifi, from Johannes Berg.

 5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.

 6) Fix dst_entry usage in ARP replies, from Jiri Benc.

 7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.

 8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.

 9) Various resource allocation/freeing cures in DSA< from Neil
    Armstrong.

10) A series of bug fixes in the openvswitch conntrack support, from
    Joe Stringer.

11) Fix two cases (BPF and act_mirred) where we have to clean the sender
    cpu stored in the SKB before transmitting.  From WANG Cong and
    Alexei Starovoitov.

12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
    Achiad Shochat.

13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
    configuration via ethtool.  From Yuval Mintz.

14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
    'dev' is NULL, from Eric Biederman.

15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.

16) kcalloc() gstrings ethtool buffer before having driver fill it in,
    in order to prevent kernel memory leaking.  From Joe Perches.

17) Fix mixxing rt6_info initialization for blackhole routes, from
    Martin KaFai Lau.

18) Kill VLAN regression in via-rhine, from Andrej Ota.

19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.

20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.

21) Scrube SKBs when pushing them between namespaces in openvswitch,
    from Joe Stringer.

22) bcmgenet enables link interrupts too early, fix from Florian
    Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
  net: bcmgenet: Fix early link interrupt enabling
  tunnels: Don't require remote endpoint or ID during creation.
  openvswitch: Scrub skb between namespaces
  xen-netback: correctly check failed allocation
  net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
  netlink: Trim skb to alloc size to avoid MSG_TRUNC
  net: add pfmemalloc check in sk_add_backlog()
  via-rhine: fix VLAN receive handling regression.
  ipv6: Initialize rt6_info properly in ip6_blackhole_route()
  ipv6: Move common init code for rt6_info to a new function rt6_info_init()
  Bluetooth: Fix initializing conn_params in scan phase
  Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
  Bluetooth: Fix remove_device behavior for explicit connects
  Bluetooth: Fix LE reconnection logic
  Bluetooth: Fix reference counting for LE-scan based connections
  Bluetooth: Fix double scan updates
  mlxsw: core: Fix race condition in __mlxsw_emad_transmit
  tipc: move fragment importance field to new header position
  ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
  tipc: eliminate risk of stalled link synchronization
  ...

If request_key() is used to find a keyring, only do the search part - don't
do the construction part if the keyring was not found by the search.  We
don't really want keyrings in the negative instantiated state since the
rejected/negative instantiation error value in the payload is unioned with
keyring metadata.

Now the kernel gives an error:

	request_key("keyring", "#selinux,bdekeyring", "keyring", KEY_SPEC_USER_SESSION_KEYRING) = -1 EPERM (Operation not permitted)
Signed-off-by: David Howells <dhowells@redhat.com>

Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.

Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.

Fixes: 6cc8e6d4 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-10-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
iwlwifi:

* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment

rtlwifi:

* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.

An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.

CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.

This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2015-10-16

First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.

The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.

The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.

I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.

netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.

Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).

It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.

This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull i2c fixes from Wolfram Sang:
 "Here are some bugfixes for the I2C subsystem.

  Kieran found a flaw in the recently renewed wake irq handling.  Mika
  handled a user bug report where the ACPI info turned out to be
  unusable.  I updated MAINTAINERS so that such bug reports will sooner
  get to the right people.  Geert pointed me to a problem of some i2c
  drivers regarding PM which I fixed"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
  MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
  i2c: designware-platdrv: enable RuntimePM before registering to the core
  i2c: s3c2410: enable RuntimePM before registering to the core
  i2c: rcar: enable RuntimePM before registering to the core
  i2c: return probe deferred status on dev_pm_domain_attach

ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:

  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: controller timed out

The values received from ACPI are (in fast mode):

  HCNT: 72
  LCNT: 160

this translates to following timings (input clock is 100MHz on Broadwell):

  tHIGH: 720 ns (spec min 600 ns)
  tLOW: 1600 ns (spec min 1300 ns)
  Bus period: 2920 ns (assuming 300 ns tf and tr)
  Bus speed: 342.5 kHz

Both tHIGH and tLOW are within the I2C specification.

The calculated values when ACPI parameters are not used are (in fast mode):

  HCNT: 87
  LCNT: 159

which translates to:

  tHIGH: 870 ns (spec min 600 ns)
  tLOW: 1590 ns (spec min 1300 ns)
  Bus period 3060 ns (assuming 300 ns tf and tr)
  Bus speed 326.8 kHz

These values are also within the I2C specification.

Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).

Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq/timer fixes from Thomas Gleixner:
 "irq: a fix for the new hierarchical MSI interrupt handling which
  unbreaks PCI=n configurations.

  timers: a fix for the new hrtimer clock offset update mechanism to
  ensure that the boot time offset is respected"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/msi: Do not use pci_msi_[un]mask_irq as default methods

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Increment clock_was_set_seq in timekeeping_init()

Greg reported crashes hitting the following check in __sk_backlog_rcv()

	BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));

The pfmemalloc bit is currently checked in sk_filter().

This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.

For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.

Fixes: b4b9e355 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input fixes from Dmitry Torokhov:
 "Just two small fixups to ads7846 touchscreen controller driver and
  Cypress touchpad driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: cyapa - fix the copy paste error on electrodes_rx value
  Input: ads7846 - correct the value got from SPI

Pull clk fix from Stephen Boyd:
 "Just one revert for Armada XP devices: the conversion to
  of_clk_get_parent_name() wasn't a direct translation, so we
  revert back to of_clk_get() + __clk_get_name().

  We could make of_clk_get_parent_name() more robust, but that
  may have unintended side-effects, so we'll do that in the
  next version"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"

Pull device mapper fixes from Mike Snitzer:
 "Two DM target error path cleanup fixes (one for stable in DM thinp and
  one for a v4.3-rc5 thinko in DM snapshot)"

* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm thin: fix missing pool reference count decrement in pool_ctr error path
  dm snapshot persistent: fix missing cleanup in persistent_ctr error path

Pull btrfs fixes from Chris Mason:
 "I have two more bug fixes for btrfs.

  My commit fixes a bug we hit last week at FB, a combination of lots of
  hard links and an admin command to resolve inode numbers.

  Dave is adding checks to make sure balance on current kernels ignores
  filters it doesn't understand.  The penalty for being wrong is just
  doing more work (not crashing etc), but it's a good fix"

* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: fix use after free iterating extrefs
  btrfs: check unsupported filters in balance arguments

Pull Ceph fixes from Sage Weil:
 "Just two small items from Ilya:

  The first patch fixes the RBD readahead to grab full objects.  The
  second fixes the write ops to prevent undue promotion when a cache
  tier is configured on the server side"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: use writefull op for object size writes
  rbd: set max_sectors explicitly

Pull power management and ACPI fixes from Rafael Wysocki:
 "These fix two recent regressions (ACPICA, the generic power domains
  framework) and one crash that may happen on specific hardware
  supported since 4.1 (intel_pstate).

  Specifics:

   - Fix a regression introduced by a recent ACPICA cleanup that
     uncovered a latent bug (Lv Zheng).

   - Fix a recent regression in the generic power domains framework that
     may cause it to violate PM QoS latency constraints in some cases
     (Ulf Hansson).

   - Fix an intel_pstate driver crash on the Knights Landing chips that
     do not update the MPERF counter as often as expected by the driver
     which may result in a divide by 0 (Srinivas Pandruvada)"

* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
  ACPICA: Tables: Fix FADT dependency regression
  PM / Domains: Fix validation of latency constraints in genpd governor

Pull drm fixes from Dave Airlie:
 "Nothing too crazy or exciting:

   - two MAINTAINERS entries that I didn't see the point in delaying.
   - one drm mst fix to stop sending uninitialised data to monitors
   - two amdgpu fixes
   - one radeon mst tiling fix
   - one vmwgfx regression fix
   - one virtio warning fix.

  I have found one locking problem that needs a bit of reorg to fix, but
  I'm not sure it's worth putting in -fixes as I don't think we've seen
  it hit in the real world ever, I just found it using the virtio-gpu
  driver when working on it.  I'll possibly send it next week once I've
  time to discuss with Daniel"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/virtio: use %llu format string form atomic64_t
  MAINTAINERS: Add myself as maintainer for the gma500 driver
  MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
  drm/amdgpu: Keep the pflip interrupts always enabled v7
  drm/amdgpu: adjust default dispclk (v2)
  drm/dp/mst: make mst i2c transfer code more robust.
  drm/radeon: attach tile property to mst connector
  drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware

Pull powerpc fixes from Michael Ellerman:
 - Re-enable CONFIG_SCSI_DH in our defconfigs
 - Remove unused os_area_db_id_video_mode
 - cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
 - cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
 - cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
 - cxl: Workaround malformed pcie packets on some cards from Philippe
 - cxl: Fix number of allocated pages in SPA from Christophe Lombard
 - Fix checkstop in native_hpte_clear() with lockdep from Cyril
 - Panic on unhandled Machine Check on powernv from Daniel
 - selftests/powerpc: Fix build failure of load_unaligned_zeropad test

* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  selftests/powerpc: Fix build failure of load_unaligned_zeropad test
  powerpc/powernv: Panic on unhandled Machine Check
  powerpc: Fix checkstop in native_hpte_clear() with lockdep
  cxl: Fix number of allocated pages in SPA
  cxl: Workaround malformed pcie packets on some cards
  cxl: fix leak of ctx->mapping when releasing kernel API contexts
  cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
  cxl: fix leak of IRQ names in cxl_free_afu_irqs()
  powerpc/ps3: Remove unused os_area_db_id_video_mode
  powerpc/configs: Re-enable CONFIG_SCSI_DH